* [PATCH 0/6] serial: Cleanup literals
@ 2022-11-24 12:59 Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 1/6] serial: 8250: Use defined IER bits Ilpo Järvinen
` (5 more replies)
0 siblings, 6 replies; 8+ messages in thread
From: Ilpo Järvinen @ 2022-11-24 12:59 UTC (permalink / raw)
To: linux-serial, Greg Kroah-Hartman, Jiri Slaby
Cc: linux-kernel, Ilpo Järvinen
Convert plenty of register write literals to use the proper defines. In
most of the cases the defines already exist but a few new defines are
added too for combined sets of flags.
Ilpo Järvinen (6):
serial: 8250: Use defined IER bits
serial: 8250: Name MSR literals
serial: 8250: Cleanup MCR literals
serial: 8250: Add IIR FIFOs enabled field properly
serial: 8250: Define IIR 64 byte bit & cleanup related code
serial: 8250_early: Convert literals to use defines
drivers/tty/serial/8250/8250_early.c | 4 +--
drivers/tty/serial/8250/8250_port.c | 47 ++++++++++++++--------------
include/linux/serial.h | 10 ++++++
include/uapi/linux/serial_reg.h | 5 +++
4 files changed, 41 insertions(+), 25 deletions(-)
--
2.30.2
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH 1/6] serial: 8250: Use defined IER bits
2022-11-24 12:59 [PATCH 0/6] serial: Cleanup literals Ilpo Järvinen
@ 2022-11-24 12:59 ` Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 2/6] serial: 8250: Name MSR literals Ilpo Järvinen
` (4 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Ilpo Järvinen @ 2022-11-24 12:59 UTC (permalink / raw)
To: linux-serial, Greg Kroah-Hartman, Jiri Slaby, linux-kernel
Cc: Ilpo Järvinen
Instead of literal 0x0f, add a define for enabling all IER bits the
8250 driver is interested in.
Don't make the define for combined flags part of UAPI.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250_port.c | 10 +++++-----
include/linux/serial.h | 5 +++++
2 files changed, 10 insertions(+), 5 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index beba8f38b3dc..8676f8b7f2e3 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1236,14 +1236,14 @@ static void autoconfig(struct uart_8250_port *up)
* Mask out IER[7:4] bits for test as some UARTs (e.g. TL
* 16C754B) allow only to modify them if an EFR bit is set.
*/
- scratch2 = serial_in(up, UART_IER) & 0x0f;
- serial_out(up, UART_IER, 0x0F);
+ scratch2 = serial_in(up, UART_IER) & UART_IER_ALL_INTR;
+ serial_out(up, UART_IER, UART_IER_ALL_INTR);
#ifdef __i386__
outb(0, 0x080);
#endif
- scratch3 = serial_in(up, UART_IER) & 0x0f;
+ scratch3 = serial_in(up, UART_IER) & UART_IER_ALL_INTR;
serial_out(up, UART_IER, scratch);
- if (scratch2 != 0 || scratch3 != 0x0F) {
+ if (scratch2 != 0 || scratch3 != UART_IER_ALL_INTR) {
/*
* We failed; there's nothing here
*/
@@ -1394,7 +1394,7 @@ static void autoconfig_irq(struct uart_8250_port *up)
serial8250_out_MCR(up,
UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
}
- serial_out(up, UART_IER, 0x0f); /* enable all intrs */
+ serial_out(up, UART_IER, UART_IER_ALL_INTR);
serial_in(up, UART_LSR);
serial_in(up, UART_RX);
serial_in(up, UART_IIR);
diff --git a/include/linux/serial.h b/include/linux/serial.h
index 3d6fe3ef92cf..ad6e1c37e2d5 100644
--- a/include/linux/serial.h
+++ b/include/linux/serial.h
@@ -12,6 +12,11 @@
#include <uapi/linux/serial.h>
#include <uapi/linux/serial_reg.h>
+#define UART_IER_ALL_INTR (UART_IER_MSI | \
+ UART_IER_RLSI | \
+ UART_IER_THRI | \
+ UART_IER_RDI)
+
/* Helper for dealing with UART_LCR_WLEN* defines */
#define UART_LCR_WLEN(x) ((x) - 5)
--
2.30.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 2/6] serial: 8250: Name MSR literals
2022-11-24 12:59 [PATCH 0/6] serial: Cleanup literals Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 1/6] serial: 8250: Use defined IER bits Ilpo Järvinen
@ 2022-11-24 12:59 ` Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 3/6] serial: 8250: Cleanup MCR literals Ilpo Järvinen
` (3 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Ilpo Järvinen @ 2022-11-24 12:59 UTC (permalink / raw)
To: linux-serial, Greg Kroah-Hartman, Jiri Slaby, linux-kernel
Cc: Ilpo Järvinen
Add UART_MSR_STATUS_BITS for CD, RI, DSR & CTS. Use names for the
literal.
Don't make the define for combined flags part of UAPI.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250_port.c | 4 ++--
include/linux/serial.h | 5 +++++
2 files changed, 7 insertions(+), 2 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 8676f8b7f2e3..c870ee8e80b6 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1268,9 +1268,9 @@ static void autoconfig(struct uart_8250_port *up)
*/
if (!(port->flags & UPF_SKIP_TEST)) {
serial8250_out_MCR(up, UART_MCR_LOOP | 0x0A);
- status1 = serial_in(up, UART_MSR) & 0xF0;
+ status1 = serial_in(up, UART_MSR) & UART_MSR_STATUS_BITS;
serial8250_out_MCR(up, save_mcr);
- if (status1 != 0x90) {
+ if (status1 != (UART_MSR_DCD | UART_MSR_CTS)) {
spin_unlock_irqrestore(&port->lock, flags);
DEBUG_AUTOCONF("LOOP test failed (%02x) ",
status1);
diff --git a/include/linux/serial.h b/include/linux/serial.h
index ad6e1c37e2d5..bfda927dde15 100644
--- a/include/linux/serial.h
+++ b/include/linux/serial.h
@@ -28,6 +28,11 @@ static inline bool uart_lsr_tx_empty(u16 lsr)
return (lsr & UART_LSR_BOTH_EMPTY) == UART_LSR_BOTH_EMPTY;
}
+#define UART_MSR_STATUS_BITS (UART_MSR_DCD | \
+ UART_MSR_RI | \
+ UART_MSR_DSR | \
+ UART_MSR_CTS)
+
/*
* Counters of the input lines (CTS, DSR, RI, CD) interrupts
*/
--
2.30.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 3/6] serial: 8250: Cleanup MCR literals
2022-11-24 12:59 [PATCH 0/6] serial: Cleanup literals Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 1/6] serial: 8250: Use defined IER bits Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 2/6] serial: 8250: Name MSR literals Ilpo Järvinen
@ 2022-11-24 12:59 ` Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 4/6] serial: 8250: Add IIR FIFOs enabled field properly Ilpo Järvinen
` (2 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Ilpo Järvinen @ 2022-11-24 12:59 UTC (permalink / raw)
To: linux-serial, Greg Kroah-Hartman, Jiri Slaby, linux-kernel
Cc: Ilpo Järvinen
Use proper names from MCR bits.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250_port.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index c870ee8e80b6..e79bf2afd9be 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1267,7 +1267,7 @@ static void autoconfig(struct uart_8250_port *up)
* that conflicts with COM 1-4 --- we hope!
*/
if (!(port->flags & UPF_SKIP_TEST)) {
- serial8250_out_MCR(up, UART_MCR_LOOP | 0x0A);
+ serial8250_out_MCR(up, UART_MCR_LOOP | UART_MCR_OUT2 | UART_MCR_RTS);
status1 = serial_in(up, UART_MSR) & UART_MSR_STATUS_BITS;
serial8250_out_MCR(up, save_mcr);
if (status1 != (UART_MSR_DCD | UART_MSR_CTS)) {
--
2.30.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 4/6] serial: 8250: Add IIR FIFOs enabled field properly
2022-11-24 12:59 [PATCH 0/6] serial: Cleanup literals Ilpo Järvinen
` (2 preceding siblings ...)
2022-11-24 12:59 ` [PATCH 3/6] serial: 8250: Cleanup MCR literals Ilpo Järvinen
@ 2022-11-24 12:59 ` Ilpo Järvinen
2022-11-25 11:08 ` Jiri Slaby
2022-11-24 12:59 ` [PATCH 5/6] serial: 8250: Define IIR 64 byte bit & cleanup related code Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 6/6] serial: 8250_early: Convert literals to use defines Ilpo Järvinen
5 siblings, 1 reply; 8+ messages in thread
From: Ilpo Järvinen @ 2022-11-24 12:59 UTC (permalink / raw)
To: linux-serial, Greg Kroah-Hartman, Jiri Slaby, linux-kernel
Cc: Ilpo Järvinen
Don't use magic literals & comments but define a real field instead
for UART_IIR_FIFO_ENABLED and name also the values.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250_port.c | 17 +++++++----------
include/uapi/linux/serial_reg.h | 4 ++++
2 files changed, 11 insertions(+), 10 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index e79bf2afd9be..6d343b15bc58 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1293,22 +1293,19 @@ static void autoconfig(struct uart_8250_port *up)
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- /* Assign this as it is to truncate any bits above 7. */
- scratch = serial_in(up, UART_IIR);
-
- switch (scratch >> 6) {
- case 0:
+ switch (serial_in(up, UART_IIR) & UART_IIR_FIFO_ENABLED) {
+ case UART_IIR_FIFO_ENABLED_8250:
autoconfig_8250(up);
break;
- case 1:
- port->type = PORT_UNKNOWN;
- break;
- case 2:
+ case UART_IIR_FIFO_EAABLED_16550:
port->type = PORT_16550;
break;
- case 3:
+ case UART_IIR_FIFO_ENABLED_16550A:
autoconfig_16550a(up);
break;
+ default:
+ port->type = PORT_UNKNOWN;
+ break;
}
#ifdef CONFIG_SERIAL_8250_RSA
diff --git a/include/uapi/linux/serial_reg.h b/include/uapi/linux/serial_reg.h
index bab3b39266cc..a63c124b7fdc 100644
--- a/include/uapi/linux/serial_reg.h
+++ b/include/uapi/linux/serial_reg.h
@@ -44,6 +44,10 @@
#define UART_IIR_RX_TIMEOUT 0x0c /* OMAP RX Timeout interrupt */
#define UART_IIR_XOFF 0x10 /* OMAP XOFF/Special Character */
#define UART_IIR_CTS_RTS_DSR 0x20 /* OMAP CTS/RTS/DSR Change */
+#define UART_IIR_FIFO_ENABLED 0xc0 /* FIFOs enabled / port type identification */
+#define UART_IIR_FIFO_ENABLED_8250 0x00 /* 8250: no FIFO */
+#define UART_IIR_FIFO_EAABLED_16550 0x80 /* 16550: (broken/unusable) FIFO */
+#define UART_IIR_FIFO_ENABLED_16550A 0xc0 /* 16550A: FIFO enabled */
#define UART_FCR 2 /* Out: FIFO Control Register */
#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
--
2.30.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 5/6] serial: 8250: Define IIR 64 byte bit & cleanup related code
2022-11-24 12:59 [PATCH 0/6] serial: Cleanup literals Ilpo Järvinen
` (3 preceding siblings ...)
2022-11-24 12:59 ` [PATCH 4/6] serial: 8250: Add IIR FIFOs enabled field properly Ilpo Järvinen
@ 2022-11-24 12:59 ` Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 6/6] serial: 8250_early: Convert literals to use defines Ilpo Järvinen
5 siblings, 0 replies; 8+ messages in thread
From: Ilpo Järvinen @ 2022-11-24 12:59 UTC (permalink / raw)
To: linux-serial, Greg Kroah-Hartman, Jiri Slaby, linux-kernel
Cc: Ilpo Järvinen
16750 indicates 64 bytes FIFO with a IIR bit. Add define for it and
make related code more obvious.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250_port.c | 14 +++++++++-----
include/uapi/linux/serial_reg.h | 1 +
2 files changed, 10 insertions(+), 5 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 6d343b15bc58..764043931a99 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1050,11 +1050,12 @@ static void autoconfig_16550a(struct uart_8250_port *up)
serial_out(up, UART_LCR, 0);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR7_64BYTE);
- status1 = serial_in(up, UART_IIR) >> 5;
+ status1 = serial_in(up, UART_IIR) & (UART_IIR_64BYTE_FIFO |
+ UART_IIR_FIFO_ENABLED);
serial_out(up, UART_FCR, 0);
serial_out(up, UART_LCR, 0);
- if (status1 == 7)
+ if (status1 == (UART_IIR_64BYTE_FIFO | UART_IIR_FIFO_ENABLED))
up->port.type = PORT_16550A_FSL64;
else
DEBUG_AUTOCONF("Motorola 8xxx DUART ");
@@ -1122,17 +1123,20 @@ static void autoconfig_16550a(struct uart_8250_port *up)
*/
serial_out(up, UART_LCR, 0);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
- status1 = serial_in(up, UART_IIR) >> 5;
+ status1 = serial_in(up, UART_IIR) & (UART_IIR_64BYTE_FIFO | UART_IIR_FIFO_ENABLED);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
- status2 = serial_in(up, UART_IIR) >> 5;
+ status2 = serial_in(up, UART_IIR) & (UART_IIR_64BYTE_FIFO | UART_IIR_FIFO_ENABLED);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+
serial_out(up, UART_LCR, 0);
DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2);
- if (status1 == 6 && status2 == 7) {
+ if (status1 == UART_IIR_FIFO_ENABLED_16550A &&
+ status2 == (UART_IIR_64BYTE_FIFO | UART_IIR_FIFO_ENABLED_16550A)) {
up->port.type = PORT_16750;
up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP;
return;
diff --git a/include/uapi/linux/serial_reg.h b/include/uapi/linux/serial_reg.h
index a63c124b7fdc..21ae5b930c7b 100644
--- a/include/uapi/linux/serial_reg.h
+++ b/include/uapi/linux/serial_reg.h
@@ -44,6 +44,7 @@
#define UART_IIR_RX_TIMEOUT 0x0c /* OMAP RX Timeout interrupt */
#define UART_IIR_XOFF 0x10 /* OMAP XOFF/Special Character */
#define UART_IIR_CTS_RTS_DSR 0x20 /* OMAP CTS/RTS/DSR Change */
+#define UART_IIR_64BYTE_FIFO 0x20 /* 16750 64 bytes FIFO */
#define UART_IIR_FIFO_ENABLED 0xc0 /* FIFOs enabled / port type identification */
#define UART_IIR_FIFO_ENABLED_8250 0x00 /* 8250: no FIFO */
#define UART_IIR_FIFO_EAABLED_16550 0x80 /* 16550: (broken/unusable) FIFO */
--
2.30.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 6/6] serial: 8250_early: Convert literals to use defines
2022-11-24 12:59 [PATCH 0/6] serial: Cleanup literals Ilpo Järvinen
` (4 preceding siblings ...)
2022-11-24 12:59 ` [PATCH 5/6] serial: 8250: Define IIR 64 byte bit & cleanup related code Ilpo Järvinen
@ 2022-11-24 12:59 ` Ilpo Järvinen
5 siblings, 0 replies; 8+ messages in thread
From: Ilpo Järvinen @ 2022-11-24 12:59 UTC (permalink / raw)
To: linux-serial, Greg Kroah-Hartman, Jiri Slaby, linux-kernel
Cc: Ilpo Järvinen
Use existing defines for the serial register values in 8250_early.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
drivers/tty/serial/8250/8250_early.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c
index f271becfc46c..0ebde0ab8167 100644
--- a/drivers/tty/serial/8250/8250_early.c
+++ b/drivers/tty/serial/8250/8250_early.c
@@ -136,11 +136,11 @@ static void __init init_port(struct earlycon_device *device)
unsigned char c;
unsigned int ier;
- serial8250_early_out(port, UART_LCR, 0x3); /* 8n1 */
+ serial8250_early_out(port, UART_LCR, UART_LCR_WLEN8); /* 8n1 */
ier = serial8250_early_in(port, UART_IER);
serial8250_early_out(port, UART_IER, ier & UART_IER_UUE); /* no interrupt */
serial8250_early_out(port, UART_FCR, 0); /* no fifo */
- serial8250_early_out(port, UART_MCR, 0x3); /* DTR + RTS */
+ serial8250_early_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS);
if (port->uartclk) {
divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * device->baud);
--
2.30.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH 4/6] serial: 8250: Add IIR FIFOs enabled field properly
2022-11-24 12:59 ` [PATCH 4/6] serial: 8250: Add IIR FIFOs enabled field properly Ilpo Järvinen
@ 2022-11-25 11:08 ` Jiri Slaby
0 siblings, 0 replies; 8+ messages in thread
From: Jiri Slaby @ 2022-11-25 11:08 UTC (permalink / raw)
To: Ilpo Järvinen, linux-serial, Greg Kroah-Hartman, linux-kernel
On 24. 11. 22, 13:59, Ilpo Järvinen wrote:
> Don't use magic literals & comments but define a real field instead
> for UART_IIR_FIFO_ENABLED and name also the values.
>
> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
> ---
> drivers/tty/serial/8250/8250_port.c | 17 +++++++----------
> include/uapi/linux/serial_reg.h | 4 ++++
> 2 files changed, 11 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
> index e79bf2afd9be..6d343b15bc58 100644
> --- a/drivers/tty/serial/8250/8250_port.c
> +++ b/drivers/tty/serial/8250/8250_port.c
> @@ -1293,22 +1293,19 @@ static void autoconfig(struct uart_8250_port *up)
>
> serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
>
> - /* Assign this as it is to truncate any bits above 7. */
> - scratch = serial_in(up, UART_IIR);
> -
> - switch (scratch >> 6) {
> - case 0:
> + switch (serial_in(up, UART_IIR) & UART_IIR_FIFO_ENABLED) {
> + case UART_IIR_FIFO_ENABLED_8250:
> autoconfig_8250(up);
> break;
> - case 1:
> - port->type = PORT_UNKNOWN;
> - break;
> - case 2:
> + case UART_IIR_FIFO_EAABLED_16550:
EAABLED :)?
> --- a/include/uapi/linux/serial_reg.h
> +++ b/include/uapi/linux/serial_reg.h
> @@ -44,6 +44,10 @@
> #define UART_IIR_RX_TIMEOUT 0x0c /* OMAP RX Timeout interrupt */
> #define UART_IIR_XOFF 0x10 /* OMAP XOFF/Special Character */
> #define UART_IIR_CTS_RTS_DSR 0x20 /* OMAP CTS/RTS/DSR Change */
> +#define UART_IIR_FIFO_ENABLED 0xc0 /* FIFOs enabled / port type identification */
> +#define UART_IIR_FIFO_ENABLED_8250 0x00 /* 8250: no FIFO */
> +#define UART_IIR_FIFO_EAABLED_16550 0x80 /* 16550: (broken/unusable) FIFO */
> +#define UART_IIR_FIFO_ENABLED_16550A 0xc0 /* 16550A: FIFO enabled */
>
> #define UART_FCR 2 /* Out: FIFO Control Register */
> #define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
--
js
suse labs
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2022-11-25 11:08 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-11-24 12:59 [PATCH 0/6] serial: Cleanup literals Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 1/6] serial: 8250: Use defined IER bits Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 2/6] serial: 8250: Name MSR literals Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 3/6] serial: 8250: Cleanup MCR literals Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 4/6] serial: 8250: Add IIR FIFOs enabled field properly Ilpo Järvinen
2022-11-25 11:08 ` Jiri Slaby
2022-11-24 12:59 ` [PATCH 5/6] serial: 8250: Define IIR 64 byte bit & cleanup related code Ilpo Järvinen
2022-11-24 12:59 ` [PATCH 6/6] serial: 8250_early: Convert literals to use defines Ilpo Järvinen
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).