* [PATCH V7] GCOV: Add config to check the preqequisites situation
@ 2020-07-27 8:51 gengcixi
2020-08-20 12:40 ` Cixi Geng
0 siblings, 1 reply; 4+ messages in thread
From: gengcixi @ 2020-07-27 8:51 UTC (permalink / raw)
To: gregkh, jslaby, oberpar, linux-serial, linux-kernel
Cc: orsonzhai, zhang.lyra, Cixi Geng
From: Cixi Geng <cixi.geng1@unisoc.com>
Introduce new configuration option GCOV_PROFILE_PREREQS that can be
used to check whether the prerequisites for enabling gcov profiling
for specific files and directories are met.
Only add SERIAL_GCOV for an example.
Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
---
drivers/tty/serial/Kconfig | 7 +++++++
drivers/tty/serial/Makefile | 1 +
kernel/gcov/Kconfig | 12 ++++++++++++
3 files changed, 20 insertions(+)
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 780908d43557..55b128b6b31d 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1576,3 +1576,10 @@ endmenu
config SERIAL_MCTRL_GPIO
tristate
+
+config SERIAL_GCOV
+ bool "Enable profile gcov for serial directory"
+ depends on GCOV_PROFILE_PREREQS
+ help
+ The SERIAL_GCOV will add Gcov profiling flags when kernel compiles.
+ Say 'Y' here if you want the gcov data for the serial directory,
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index d056ee6cca33..17272733db95 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -3,6 +3,7 @@
# Makefile for the kernel serial device drivers.
#
+GCOV_PROFILE := $(CONFIG_SERIAL_GCOV)
obj-$(CONFIG_SERIAL_CORE) += serial_core.o
obj-$(CONFIG_SERIAL_EARLYCON) += earlycon.o
diff --git a/kernel/gcov/Kconfig b/kernel/gcov/Kconfig
index 3110c77230c7..bb2e1fb85743 100644
--- a/kernel/gcov/Kconfig
+++ b/kernel/gcov/Kconfig
@@ -51,4 +51,16 @@ config GCOV_PROFILE_ALL
larger and run slower. Also be sure to exclude files from profiling
which are not linked to the kernel image to prevent linker errors.
+config GCOV_PROFILE_PREREQS
+ bool "Profile Kernel for prereqs"
+ depends on GCOV_KERNEL
+ depends on !COMPILE_TEST
+ def_bool y if GCOV_KERNEL && !COMPILE_TEST
+ help
+ This options activates profiling for the specified kernel modules.
+
+ When some modules need Gcov data, enable this config, then configure
+ with gcov on the corresponding modules,The directories or files of
+ these modules will be added profiling flags after kernel compile.
+
endmenu
--
2.17.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH V7] GCOV: Add config to check the preqequisites situation
2020-07-27 8:51 [PATCH V7] GCOV: Add config to check the preqequisites situation gengcixi
@ 2020-08-20 12:40 ` Cixi Geng
2020-09-16 12:55 ` Cixi Geng
0 siblings, 1 reply; 4+ messages in thread
From: Cixi Geng @ 2020-08-20 12:40 UTC (permalink / raw)
To: Greg KH, jslaby, Peter Oberparleiter, linux-serial, linux-kernel
Cc: Orson Zhai, zhang.lyra, Cixi Geng
Hi All:
Does this patch need more modification?
<gengcixi@gmail.com> 于2020年7月27日周一 下午4:51写道:
>
> From: Cixi Geng <cixi.geng1@unisoc.com>
>
> Introduce new configuration option GCOV_PROFILE_PREREQS that can be
> used to check whether the prerequisites for enabling gcov profiling
> for specific files and directories are met.
>
> Only add SERIAL_GCOV for an example.
>
> Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
> ---
> drivers/tty/serial/Kconfig | 7 +++++++
> drivers/tty/serial/Makefile | 1 +
> kernel/gcov/Kconfig | 12 ++++++++++++
> 3 files changed, 20 insertions(+)
>
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index 780908d43557..55b128b6b31d 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -1576,3 +1576,10 @@ endmenu
>
> config SERIAL_MCTRL_GPIO
> tristate
> +
> +config SERIAL_GCOV
> + bool "Enable profile gcov for serial directory"
> + depends on GCOV_PROFILE_PREREQS
> + help
> + The SERIAL_GCOV will add Gcov profiling flags when kernel compiles.
> + Say 'Y' here if you want the gcov data for the serial directory,
> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
> index d056ee6cca33..17272733db95 100644
> --- a/drivers/tty/serial/Makefile
> +++ b/drivers/tty/serial/Makefile
> @@ -3,6 +3,7 @@
> # Makefile for the kernel serial device drivers.
> #
>
> +GCOV_PROFILE := $(CONFIG_SERIAL_GCOV)
> obj-$(CONFIG_SERIAL_CORE) += serial_core.o
>
> obj-$(CONFIG_SERIAL_EARLYCON) += earlycon.o
> diff --git a/kernel/gcov/Kconfig b/kernel/gcov/Kconfig
> index 3110c77230c7..bb2e1fb85743 100644
> --- a/kernel/gcov/Kconfig
> +++ b/kernel/gcov/Kconfig
> @@ -51,4 +51,16 @@ config GCOV_PROFILE_ALL
> larger and run slower. Also be sure to exclude files from profiling
> which are not linked to the kernel image to prevent linker errors.
>
> +config GCOV_PROFILE_PREREQS
> + bool "Profile Kernel for prereqs"
> + depends on GCOV_KERNEL
> + depends on !COMPILE_TEST
> + def_bool y if GCOV_KERNEL && !COMPILE_TEST
> + help
> + This options activates profiling for the specified kernel modules.
> +
> + When some modules need Gcov data, enable this config, then configure
> + with gcov on the corresponding modules,The directories or files of
> + these modules will be added profiling flags after kernel compile.
> +
> endmenu
> --
> 2.17.1
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH V7] GCOV: Add config to check the preqequisites situation
2020-08-20 12:40 ` Cixi Geng
@ 2020-09-16 12:55 ` Cixi Geng
2020-10-22 10:03 ` Peter Oberparleiter
0 siblings, 1 reply; 4+ messages in thread
From: Cixi Geng @ 2020-09-16 12:55 UTC (permalink / raw)
To: Greg KH, jslaby, Peter Oberparleiter, linux-serial, linux-kernel
Cc: Orson Zhai, zhang.lyra, Cixi Geng
Hi ALL:
Not recieve more advise for a long time ,
Can this submission be merged recently?
Cixi Geng <gengcixi@gmail.com> 于2020年8月20日周四 下午8:40写道:
>
> Hi All:
>
> Does this patch need more modification?
>
> <gengcixi@gmail.com> 于2020年7月27日周一 下午4:51写道:
> >
> > From: Cixi Geng <cixi.geng1@unisoc.com>
> >
> > Introduce new configuration option GCOV_PROFILE_PREREQS that can be
> > used to check whether the prerequisites for enabling gcov profiling
> > for specific files and directories are met.
> >
> > Only add SERIAL_GCOV for an example.
> >
> > Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
> > ---
> > drivers/tty/serial/Kconfig | 7 +++++++
> > drivers/tty/serial/Makefile | 1 +
> > kernel/gcov/Kconfig | 12 ++++++++++++
> > 3 files changed, 20 insertions(+)
> >
> > diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> > index 780908d43557..55b128b6b31d 100644
> > --- a/drivers/tty/serial/Kconfig
> > +++ b/drivers/tty/serial/Kconfig
> > @@ -1576,3 +1576,10 @@ endmenu
> >
> > config SERIAL_MCTRL_GPIO
> > tristate
> > +
> > +config SERIAL_GCOV
> > + bool "Enable profile gcov for serial directory"
> > + depends on GCOV_PROFILE_PREREQS
> > + help
> > + The SERIAL_GCOV will add Gcov profiling flags when kernel compiles.
> > + Say 'Y' here if you want the gcov data for the serial directory,
> > diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
> > index d056ee6cca33..17272733db95 100644
> > --- a/drivers/tty/serial/Makefile
> > +++ b/drivers/tty/serial/Makefile
> > @@ -3,6 +3,7 @@
> > # Makefile for the kernel serial device drivers.
> > #
> >
> > +GCOV_PROFILE := $(CONFIG_SERIAL_GCOV)
> > obj-$(CONFIG_SERIAL_CORE) += serial_core.o
> >
> > obj-$(CONFIG_SERIAL_EARLYCON) += earlycon.o
> > diff --git a/kernel/gcov/Kconfig b/kernel/gcov/Kconfig
> > index 3110c77230c7..bb2e1fb85743 100644
> > --- a/kernel/gcov/Kconfig
> > +++ b/kernel/gcov/Kconfig
> > @@ -51,4 +51,16 @@ config GCOV_PROFILE_ALL
> > larger and run slower. Also be sure to exclude files from profiling
> > which are not linked to the kernel image to prevent linker errors.
> >
> > +config GCOV_PROFILE_PREREQS
> > + bool "Profile Kernel for prereqs"
> > + depends on GCOV_KERNEL
> > + depends on !COMPILE_TEST
> > + def_bool y if GCOV_KERNEL && !COMPILE_TEST
> > + help
> > + This options activates profiling for the specified kernel modules.
> > +
> > + When some modules need Gcov data, enable this config, then configure
> > + with gcov on the corresponding modules,The directories or files of
> > + these modules will be added profiling flags after kernel compile.
> > +
> > endmenu
> > --
> > 2.17.1
> >
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH V7] GCOV: Add config to check the preqequisites situation
2020-09-16 12:55 ` Cixi Geng
@ 2020-10-22 10:03 ` Peter Oberparleiter
0 siblings, 0 replies; 4+ messages in thread
From: Peter Oberparleiter @ 2020-10-22 10:03 UTC (permalink / raw)
To: Cixi Geng, Greg KH, jslaby, linux-serial, linux-kernel
Cc: Orson Zhai, zhang.lyra, Cixi Geng
On 16.09.2020 14:55, Cixi Geng wrote:
> Hi ALL:
> Not recieve more advise for a long time ,
> Can this submission be merged recently?
First off, sorry for not replying earlier.
I tried out your latest version of this patch and I don't see that my
previous comments have been addressed.
To re-iterate my point: I only see value in introducing a new
GCOV-related config symbol that is automatically selected, depending on
whether (as the name implies) all prerequisites for enabling GCOV-based
kernel profiling have been met. Such a symbol can take away the burden
of duplicating the prerequisite check as has been implemented for
GCOV_PROFILE_ALL.
I see no value in introducing a new config symbol that prompts the user
for a choice.
As it is, your patch introduces a new config symbol that prompts the
user for a choice:
$ make oldconfig
scripts/kconfig/conf --oldconfig Kconfig
*
* Restart config...
*
*
* GCOV-based kernel profiling
*
Enable gcov-based kernel profiling (GCOV_KERNEL) [Y/n/?] y
Profile entire Kernel (GCOV_PROFILE_ALL) [N/y/?] n
Profile Kernel for prereqs (GCOV_PROFILE_PREREQS) [Y/n/?] (NEW)
We do not need this prompt. Users specify that they want GCOV-profiling
by selecting GCOV_KERNEL. They specify that they want area-specific
profiling in symbols like your proposed SERIAL_GCOV. There is no need
for a user to manually confirm that the prerequisites for enabling
are-specific profiling are met.
I have detailed the required changes that would remove the prompt in my
previous reply. I'll add it here again for your convenience:
>>> +++ b/kernel/gcov/Kconfig
>>> @@ -51,6 +51,16 @@ config GCOV_PROFILE_ALL
>>> larger and run slower. Also be sure to exclude files from profiling
>>> which are not linked to the kernel image to prevent linker errors.
>>>
>>> +config GCOV_PROFILE_PREREQS
>>> + bool "Profile Kernel for prereqs"
>>> + default y if GCOV_KERNEL && !COMPILE_TEST
>>> + help
>>> + This options activates profiling for the specified kernel modules.
>>> +
>>> + When some modules need Gcov data, enable this config, then configure
>>> + with gcov on the corresponding modules,The directories or files of
>>> + these modules will be added profiling flags after kernel compile.
>>> +
>
> Replace the portion above with these lines:
>
> config GCOV_PROFILE_PREREQS
> def_bool y if GCOV_KERNEL && !COMPILE_TEST
And to clarify: by "the portion above" I was referring to all quoted
lines prefixed with a '+' sign.
>
> Cixi Geng <gengcixi@gmail.com> 于2020年8月20日周四 下午8:40写道:
>>
>> Hi All:
>>
>> Does this patch need more modification?
>>
>> <gengcixi@gmail.com> 于2020年7月27日周一 下午4:51写道:
>>>
>>> From: Cixi Geng <cixi.geng1@unisoc.com>
>>>
>>> Introduce new configuration option GCOV_PROFILE_PREREQS that can be
>>> used to check whether the prerequisites for enabling gcov profiling
>>> for specific files and directories are met.
>>>
>>> Only add SERIAL_GCOV for an example.
>>>
>>> Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
>>> ---
>>> drivers/tty/serial/Kconfig | 7 +++++++
>>> drivers/tty/serial/Makefile | 1 +
>>> kernel/gcov/Kconfig | 12 ++++++++++++
>>> 3 files changed, 20 insertions(+)
>>>
>>> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
>>> index 780908d43557..55b128b6b31d 100644
>>> --- a/drivers/tty/serial/Kconfig
>>> +++ b/drivers/tty/serial/Kconfig
>>> @@ -1576,3 +1576,10 @@ endmenu
>>>
>>> config SERIAL_MCTRL_GPIO
>>> tristate
>>> +
>>> +config SERIAL_GCOV
>>> + bool "Enable profile gcov for serial directory"
>>> + depends on GCOV_PROFILE_PREREQS
>>> + help
>>> + The SERIAL_GCOV will add Gcov profiling flags when kernel compiles.
>>> + Say 'Y' here if you want the gcov data for the serial directory,
>>> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
>>> index d056ee6cca33..17272733db95 100644
>>> --- a/drivers/tty/serial/Makefile
>>> +++ b/drivers/tty/serial/Makefile
>>> @@ -3,6 +3,7 @@
>>> # Makefile for the kernel serial device drivers.
>>> #
>>>
>>> +GCOV_PROFILE := $(CONFIG_SERIAL_GCOV)
>>> obj-$(CONFIG_SERIAL_CORE) += serial_core.o
>>>
>>> obj-$(CONFIG_SERIAL_EARLYCON) += earlycon.o
>>> diff --git a/kernel/gcov/Kconfig b/kernel/gcov/Kconfig
>>> index 3110c77230c7..bb2e1fb85743 100644
>>> --- a/kernel/gcov/Kconfig
>>> +++ b/kernel/gcov/Kconfig
>>> @@ -51,4 +51,16 @@ config GCOV_PROFILE_ALL
>>> larger and run slower. Also be sure to exclude files from profiling
>>> which are not linked to the kernel image to prevent linker errors.
>>>
>>> +config GCOV_PROFILE_PREREQS
>>> + bool "Profile Kernel for prereqs"
>>> + depends on GCOV_KERNEL
>>> + depends on !COMPILE_TEST
>>> + def_bool y if GCOV_KERNEL && !COMPILE_TEST
>>> + help
>>> + This options activates profiling for the specified kernel modules.
>>> +
>>> + When some modules need Gcov data, enable this config, then configure
>>> + with gcov on the corresponding modules,The directories or files of
>>> + these modules will be added profiling flags after kernel compile.
>>> +
>>> endmenu
>>> --
>>> 2.17.1
>>>
--
Peter Oberparleiter
Linux on Z Development - IBM Germany
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2020-10-22 10:04 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-07-27 8:51 [PATCH V7] GCOV: Add config to check the preqequisites situation gengcixi
2020-08-20 12:40 ` Cixi Geng
2020-09-16 12:55 ` Cixi Geng
2020-10-22 10:03 ` Peter Oberparleiter
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).