From: Geert Uytterhoeven <geert@linux-m68k.org>
To: Mark Brown <broonie@kernel.org>
Cc: Takashi Yoshii <takasi-y@ops.dti.ne.jp>,
Magnus Damm <magnus.damm@gmail.com>,
linux-spi@vger.kernel.org, linux-sh@vger.kernel.org,
linux-kernel@vger.kernel.org,
Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Subject: [PATCH 05/10] spi: sh-msiof: Use the core cs_gpio field, and make it optional
Date: Thu, 20 Feb 2014 14:43:04 +0000 [thread overview]
Message-ID: <1392907389-21798-6-git-send-email-geert@linux-m68k.org> (raw)
In-Reply-To: <1392907389-21798-1-git-send-email-geert@linux-m68k.org>
From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
In current implementation, CS is controlled by GPIO, which is passed
through spi->controller_data. However, the MSIOF HW module has a function
to output CS by itself, which is already enabled and actual switch will be
done by pinmux.
Store the GPIO number in the core cs_gpio field, and ignore it if it is
an invalid (negative) GPIO number.
Loosely based on a patch from Takashi Yoshii <takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
---
drivers/spi/spi-sh-msiof.c | 21 ++++++++++++++++++---
1 file changed, 18 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/spi-sh-msiof.c b/drivers/spi/spi-sh-msiof.c
index 79e14586049b..92515c1ececa 100644
--- a/drivers/spi/spi-sh-msiof.c
+++ b/drivers/spi/spi-sh-msiof.c
@@ -445,6 +445,21 @@ static int sh_msiof_spi_setup_transfer(struct spi_device *spi,
return spi_bitbang_setup_transfer(spi, t);
}
+static int sh_msiof_spi_setup(struct spi_device *spi)
+{
+ struct device_node *np = spi->master->dev.of_node;
+
+ if (!np) {
+ /*
+ * Use spi->controller_data for CS (same strategy as spi_gpio),
+ * if any. otherwise let HW control CS
+ */
+ spi->cs_gpio = (uintptr_t)spi->controller_data;
+ }
+
+ return spi_bitbang_setup(spi);
+}
+
static void sh_msiof_spi_chipselect(struct spi_device *spi, int is_on)
{
struct sh_msiof_spi_priv *p = spi_master_get_devdata(spi->master);
@@ -470,8 +485,8 @@ static void sh_msiof_spi_chipselect(struct spi_device *spi, int is_on)
!!(spi->mode & SPI_CS_HIGH));
}
- /* use spi->controller data for CS (same strategy as spi_gpio) */
- gpio_set_value((uintptr_t)spi->controller_data, value);
+ if (spi->cs_gpio >= 0)
+ gpio_set_value(spi->cs_gpio, value);
if (is_on = BITBANG_CS_INACTIVE) {
if (test_and_clear_bit(0, &p->flags)) {
@@ -758,7 +773,7 @@ static int sh_msiof_spi_probe(struct platform_device *pdev)
master->bus_num = pdev->id;
master->dev.of_node = pdev->dev.of_node;
master->num_chipselect = p->info->num_chipselect;
- master->setup = spi_bitbang_setup;
+ master->setup = sh_msiof_spi_setup;
master->cleanup = spi_bitbang_cleanup;
p->bitbang.master = master;
--
1.7.9.5
next prev parent reply other threads:[~2014-02-20 14:43 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-02-20 14:42 [PATCH 00/10] spi: sh-msiof: Add support for R-Car H2 and M2 Geert Uytterhoeven
2014-02-20 14:43 ` [PATCH 01/10] spi: sh-msiof: Fix SPI bus population from DT Geert Uytterhoeven
2014-02-22 3:10 ` Mark Brown
2014-02-20 14:43 ` [PATCH 02/10] spi: sh-msiof: Typo in comment s/tx/rx/ Geert Uytterhoeven
2014-02-22 3:10 ` Mark Brown
2014-02-20 14:43 ` [PATCH 03/10] spi: sh-msiof: Change hz from unsigned long to u32 Geert Uytterhoeven
2014-02-22 3:11 ` Mark Brown
[not found] ` <1392907389-21798-1-git-send-email-geert-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org>
2014-02-20 14:43 ` [PATCH 04/10] spi: sh-msiof: Add more register documentation Geert Uytterhoeven
2014-02-22 3:11 ` Mark Brown
2014-02-20 14:43 ` [PATCH 09/10] spi: sh-msiof: Convert to let spi core validate xfer->bits_per_word Geert Uytterhoeven
2014-02-20 14:43 ` Geert Uytterhoeven [this message]
2014-02-22 3:12 ` [PATCH 05/10] spi: sh-msiof: Use the core cs_gpio field, and make it optional Mark Brown
2014-02-20 14:43 ` [PATCH 06/10] spi: sh-msiof: Improve binding documentation Geert Uytterhoeven
2014-02-20 14:43 ` [PATCH 07/10] spi: sh-msiof: Add support for R-Car H2 and M2 Geert Uytterhoeven
[not found] ` <1392907389-21798-8-git-send-email-geert-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org>
2014-02-20 15:41 ` Magnus Damm
2014-02-20 16:13 ` Geert Uytterhoeven
[not found] ` <CAMuHMdUByWPcYM8M_m5NVM4QP5cQE_tOLGQg=2fTNF7gqkUhig-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2014-02-22 3:14 ` Mark Brown
2014-02-24 2:45 ` Magnus Damm
2014-02-24 7:39 ` Geert Uytterhoeven
2014-02-24 8:09 ` Magnus Damm
2014-02-20 14:43 ` [PATCH 08/10] spi: sh-msiof: Move clock management to (un)prepare_message() Geert Uytterhoeven
2014-02-22 3:27 ` Mark Brown
2014-02-24 9:48 ` Geert Uytterhoeven
2014-02-24 13:07 ` Mark Brown
2014-02-25 1:43 ` Magnus Damm
2014-02-20 14:43 ` [PATCH 10/10] spi: sh-msiof: Use core message handling instead of spi-bitbang Geert Uytterhoeven
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1392907389-21798-6-git-send-email-geert@linux-m68k.org \
--to=geert@linux-m68k.org \
--cc=broonie@kernel.org \
--cc=geert+renesas@linux-m68k.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sh@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=magnus.damm@gmail.com \
--cc=takasi-y@ops.dti.ne.jp \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).