[PATCH 01/10 RESEND] mmc: spi: Move SSP register definitions into separate file

[Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>]

Move the definitions into separate file so separate SPI driver can be
implemented. The SSP controller in MXS can act both as a MMC host and
as a SPI host.

Based on previous attempt by:
Fabio Estevam <fabio.estevam-KZfg59tc24xl57MIdRCFDg@public.gmane.org>

Signed-off-by: Fabio Estevam <fabio.estevam-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Signed-off-by: Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>
Cc: Chris Ball <cjb-2X9k7bc8m7Mdnm+yROfE0A@public.gmane.org>
Cc: Detlev Zundel <dzu-ynQEQJNshbs@public.gmane.org>
CC: Dong Aisheng <b29396-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
Cc: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
Cc: Linux ARM kernel <linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org>
Cc: Rob Herring <rob.herring-bsGFqQB8/DxBDgjK7y7TUQ@public.gmane.org>
CC: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Stefano Babic <sbabic-ynQEQJNshbs@public.gmane.org>
Cc: Wolfgang Denk <wd-ynQEQJNshbs@public.gmane.org>
---
 drivers/mmc/host/mxs-mmc.c  |   87 ++--------------------------------
 include/linux/spi/mxs-spi.h |  109 +++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 112 insertions(+), 84 deletions(-)
 create mode 100644 include/linux/spi/mxs-spi.h

diff --git a/drivers/mmc/host/mxs-mmc.c b/drivers/mmc/host/mxs-mmc.c
index 93b661d..584f982 100644
--- a/drivers/mmc/host/mxs-mmc.c
+++ b/drivers/mmc/host/mxs-mmc.c
@@ -45,87 +45,10 @@
 #include <linux/pinctrl/consumer.h>
 #include <linux/stmp_device.h>
 #include <linux/mmc/mxs-mmc.h>
+#include <linux/spi/mxs-spi.h>
 
 #define DRIVER_NAME	"mxs-mmc"
 
-/* card detect polling timeout */
-#define MXS_MMC_DETECT_TIMEOUT			(HZ/2)
-
-#define ssp_is_old(host)	((host)->devid == IMX23_MMC)
-
-/* SSP registers */
-#define HW_SSP_CTRL0				0x000
-#define  BM_SSP_CTRL0_RUN			(1 << 29)
-#define  BM_SSP_CTRL0_SDIO_IRQ_CHECK		(1 << 28)
-#define  BM_SSP_CTRL0_IGNORE_CRC		(1 << 26)
-#define  BM_SSP_CTRL0_READ			(1 << 25)
-#define  BM_SSP_CTRL0_DATA_XFER			(1 << 24)
-#define  BP_SSP_CTRL0_BUS_WIDTH			(22)
-#define  BM_SSP_CTRL0_BUS_WIDTH			(0x3 << 22)
-#define  BM_SSP_CTRL0_WAIT_FOR_IRQ		(1 << 21)
-#define  BM_SSP_CTRL0_LONG_RESP			(1 << 19)
-#define  BM_SSP_CTRL0_GET_RESP			(1 << 17)
-#define  BM_SSP_CTRL0_ENABLE			(1 << 16)
-#define  BP_SSP_CTRL0_XFER_COUNT		(0)
-#define  BM_SSP_CTRL0_XFER_COUNT		(0xffff)
-#define HW_SSP_CMD0				0x010
-#define  BM_SSP_CMD0_DBL_DATA_RATE_EN		(1 << 25)
-#define  BM_SSP_CMD0_SLOW_CLKING_EN		(1 << 22)
-#define  BM_SSP_CMD0_CONT_CLKING_EN		(1 << 21)
-#define  BM_SSP_CMD0_APPEND_8CYC		(1 << 20)
-#define  BP_SSP_CMD0_BLOCK_SIZE			(16)
-#define  BM_SSP_CMD0_BLOCK_SIZE			(0xf << 16)
-#define  BP_SSP_CMD0_BLOCK_COUNT		(8)
-#define  BM_SSP_CMD0_BLOCK_COUNT		(0xff << 8)
-#define  BP_SSP_CMD0_CMD			(0)
-#define  BM_SSP_CMD0_CMD			(0xff)
-#define HW_SSP_CMD1				0x020
-#define HW_SSP_XFER_SIZE			0x030
-#define HW_SSP_BLOCK_SIZE			0x040
-#define  BP_SSP_BLOCK_SIZE_BLOCK_COUNT		(4)
-#define  BM_SSP_BLOCK_SIZE_BLOCK_COUNT		(0xffffff << 4)
-#define  BP_SSP_BLOCK_SIZE_BLOCK_SIZE		(0)
-#define  BM_SSP_BLOCK_SIZE_BLOCK_SIZE		(0xf)
-#define HW_SSP_TIMING(h)			(ssp_is_old(h) ? 0x050 : 0x070)
-#define  BP_SSP_TIMING_TIMEOUT			(16)
-#define  BM_SSP_TIMING_TIMEOUT			(0xffff << 16)
-#define  BP_SSP_TIMING_CLOCK_DIVIDE		(8)
-#define  BM_SSP_TIMING_CLOCK_DIVIDE		(0xff << 8)
-#define  BP_SSP_TIMING_CLOCK_RATE		(0)
-#define  BM_SSP_TIMING_CLOCK_RATE		(0xff)
-#define HW_SSP_CTRL1(h)				(ssp_is_old(h) ? 0x060 : 0x080)
-#define  BM_SSP_CTRL1_SDIO_IRQ			(1 << 31)
-#define  BM_SSP_CTRL1_SDIO_IRQ_EN		(1 << 30)
-#define  BM_SSP_CTRL1_RESP_ERR_IRQ		(1 << 29)
-#define  BM_SSP_CTRL1_RESP_ERR_IRQ_EN		(1 << 28)
-#define  BM_SSP_CTRL1_RESP_TIMEOUT_IRQ		(1 << 27)
-#define  BM_SSP_CTRL1_RESP_TIMEOUT_IRQ_EN	(1 << 26)
-#define  BM_SSP_CTRL1_DATA_TIMEOUT_IRQ		(1 << 25)
-#define  BM_SSP_CTRL1_DATA_TIMEOUT_IRQ_EN	(1 << 24)
-#define  BM_SSP_CTRL1_DATA_CRC_IRQ		(1 << 23)
-#define  BM_SSP_CTRL1_DATA_CRC_IRQ_EN		(1 << 22)
-#define  BM_SSP_CTRL1_FIFO_UNDERRUN_IRQ		(1 << 21)
-#define  BM_SSP_CTRL1_FIFO_UNDERRUN_IRQ_EN	(1 << 20)
-#define  BM_SSP_CTRL1_RECV_TIMEOUT_IRQ		(1 << 17)
-#define  BM_SSP_CTRL1_RECV_TIMEOUT_IRQ_EN	(1 << 16)
-#define  BM_SSP_CTRL1_FIFO_OVERRUN_IRQ		(1 << 15)
-#define  BM_SSP_CTRL1_FIFO_OVERRUN_IRQ_EN	(1 << 14)
-#define  BM_SSP_CTRL1_DMA_ENABLE		(1 << 13)
-#define  BM_SSP_CTRL1_POLARITY			(1 << 9)
-#define  BP_SSP_CTRL1_WORD_LENGTH		(4)
-#define  BM_SSP_CTRL1_WORD_LENGTH		(0xf << 4)
-#define  BP_SSP_CTRL1_SSP_MODE			(0)
-#define  BM_SSP_CTRL1_SSP_MODE			(0xf)
-#define HW_SSP_SDRESP0(h)			(ssp_is_old(h) ? 0x080 : 0x0a0)
-#define HW_SSP_SDRESP1(h)			(ssp_is_old(h) ? 0x090 : 0x0b0)
-#define HW_SSP_SDRESP2(h)			(ssp_is_old(h) ? 0x0a0 : 0x0c0)
-#define HW_SSP_SDRESP3(h)			(ssp_is_old(h) ? 0x0b0 : 0x0d0)
-#define HW_SSP_STATUS(h)			(ssp_is_old(h) ? 0x0c0 : 0x100)
-#define  BM_SSP_STATUS_CARD_DETECT		(1 << 28)
-#define  BM_SSP_STATUS_SDIO_IRQ			(1 << 17)
-
-#define BF_SSP(value, field)	(((value) << BP_SSP_##field) & BM_SSP_##field)
-
 #define MXS_MMC_IRQ_BITS	(BM_SSP_CTRL1_SDIO_IRQ		| \
 				 BM_SSP_CTRL1_RESP_ERR_IRQ	| \
 				 BM_SSP_CTRL1_RESP_TIMEOUT_IRQ	| \
@@ -135,12 +58,8 @@
 				 BM_SSP_CTRL1_RECV_TIMEOUT_IRQ  | \
 				 BM_SSP_CTRL1_FIFO_OVERRUN_IRQ)
 
-#define SSP_PIO_NUM	3
-
-enum mxs_mmc_id {
-	IMX23_MMC,
-	IMX28_MMC,
-};
+/* card detect polling timeout */
+#define MXS_MMC_DETECT_TIMEOUT			(HZ/2)
 
 struct mxs_mmc_host {
 	struct mmc_host			*mmc;
diff --git a/include/linux/spi/mxs-spi.h b/include/linux/spi/mxs-spi.h
new file mode 100644
index 0000000..b7ccd57
--- /dev/null
+++ b/include/linux/spi/mxs-spi.h
@@ -0,0 +1,109 @@
+/*
+ * include/linux/spi/mxs-spi.h
+ *
+ * Freescale i.MX233/i.MX28 SPI controller register definition
+ *
+ * Copyright 2008 Embedded Alley Solutions, Inc.
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#ifndef __LINUX_SPI_MXS_SPI_H__
+#define __LINUX_SPI_MXS_SPI_H__
+
+#define ssp_is_old(host)	((host)->devid == IMX23_MMC)
+
+/* SSP registers */
+#define HW_SSP_CTRL0				0x000
+#define  BM_SSP_CTRL0_RUN			(1 << 29)
+#define  BM_SSP_CTRL0_SDIO_IRQ_CHECK		(1 << 28)
+#define  BM_SSP_CTRL0_IGNORE_CRC		(1 << 26)
+#define  BM_SSP_CTRL0_READ			(1 << 25)
+#define  BM_SSP_CTRL0_DATA_XFER			(1 << 24)
+#define  BP_SSP_CTRL0_BUS_WIDTH			22
+#define  BM_SSP_CTRL0_BUS_WIDTH			(0x3 << 22)
+#define  BM_SSP_CTRL0_WAIT_FOR_IRQ		(1 << 21)
+#define  BM_SSP_CTRL0_LONG_RESP			(1 << 19)
+#define  BM_SSP_CTRL0_GET_RESP			(1 << 17)
+#define  BM_SSP_CTRL0_ENABLE			(1 << 16)
+#define  BP_SSP_CTRL0_XFER_COUNT		0
+#define  BM_SSP_CTRL0_XFER_COUNT		0xffff
+#define HW_SSP_CMD0				0x010
+#define  BM_SSP_CMD0_DBL_DATA_RATE_EN		(1 << 25)
+#define  BM_SSP_CMD0_SLOW_CLKING_EN		(1 << 22)
+#define  BM_SSP_CMD0_CONT_CLKING_EN		(1 << 21)
+#define  BM_SSP_CMD0_APPEND_8CYC		(1 << 20)
+#define  BP_SSP_CMD0_BLOCK_SIZE			16
+#define  BM_SSP_CMD0_BLOCK_SIZE			(0xf << 16)
+#define  BP_SSP_CMD0_BLOCK_COUNT		8
+#define  BM_SSP_CMD0_BLOCK_COUNT		(0xff << 8)
+#define  BP_SSP_CMD0_CMD			0
+#define  BM_SSP_CMD0_CMD			0xff
+#define HW_SSP_CMD1				0x020
+#define HW_SSP_XFER_SIZE			0x030
+#define HW_SSP_BLOCK_SIZE			0x040
+#define  BP_SSP_BLOCK_SIZE_BLOCK_COUNT		4
+#define  BM_SSP_BLOCK_SIZE_BLOCK_COUNT		(0xffffff << 4)
+#define  BP_SSP_BLOCK_SIZE_BLOCK_SIZE		0
+#define  BM_SSP_BLOCK_SIZE_BLOCK_SIZE		0xf
+#define HW_SSP_TIMING(h)			(ssp_is_old(h) ? 0x050 : 0x070)
+#define  BP_SSP_TIMING_TIMEOUT			16
+#define  BM_SSP_TIMING_TIMEOUT			(0xffff << 16)
+#define  BP_SSP_TIMING_CLOCK_DIVIDE		8
+#define  BM_SSP_TIMING_CLOCK_DIVIDE		(0xff << 8)
+#define  BP_SSP_TIMING_CLOCK_RATE		0
+#define  BM_SSP_TIMING_CLOCK_RATE		0xff
+#define HW_SSP_CTRL1(h)				(ssp_is_old(h) ? 0x060 : 0x080)
+#define  BM_SSP_CTRL1_SDIO_IRQ			(1 << 31)
+#define  BM_SSP_CTRL1_SDIO_IRQ_EN		(1 << 30)
+#define  BM_SSP_CTRL1_RESP_ERR_IRQ		(1 << 29)
+#define  BM_SSP_CTRL1_RESP_ERR_IRQ_EN		(1 << 28)
+#define  BM_SSP_CTRL1_RESP_TIMEOUT_IRQ		(1 << 27)
+#define  BM_SSP_CTRL1_RESP_TIMEOUT_IRQ_EN	(1 << 26)
+#define  BM_SSP_CTRL1_DATA_TIMEOUT_IRQ		(1 << 25)
+#define  BM_SSP_CTRL1_DATA_TIMEOUT_IRQ_EN	(1 << 24)
+#define  BM_SSP_CTRL1_DATA_CRC_IRQ		(1 << 23)
+#define  BM_SSP_CTRL1_DATA_CRC_IRQ_EN		(1 << 22)
+#define  BM_SSP_CTRL1_FIFO_UNDERRUN_IRQ		(1 << 21)
+#define  BM_SSP_CTRL1_FIFO_UNDERRUN_IRQ_EN	(1 << 20)
+#define  BM_SSP_CTRL1_RECV_TIMEOUT_IRQ		(1 << 17)
+#define  BM_SSP_CTRL1_RECV_TIMEOUT_IRQ_EN	(1 << 16)
+#define  BM_SSP_CTRL1_FIFO_OVERRUN_IRQ		(1 << 15)
+#define  BM_SSP_CTRL1_FIFO_OVERRUN_IRQ_EN	(1 << 14)
+#define  BM_SSP_CTRL1_DMA_ENABLE		(1 << 13)
+#define  BM_SSP_CTRL1_POLARITY			(1 << 9)
+#define  BP_SSP_CTRL1_WORD_LENGTH		4
+#define  BM_SSP_CTRL1_WORD_LENGTH		(0xf << 4)
+#define  BP_SSP_CTRL1_SSP_MODE			0
+#define  BM_SSP_CTRL1_SSP_MODE			0xf
+#define HW_SSP_SDRESP0(h)			(ssp_is_old(h) ? 0x080 : 0x0a0)
+#define HW_SSP_SDRESP1(h)			(ssp_is_old(h) ? 0x090 : 0x0b0)
+#define HW_SSP_SDRESP2(h)			(ssp_is_old(h) ? 0x0a0 : 0x0c0)
+#define HW_SSP_SDRESP3(h)			(ssp_is_old(h) ? 0x0b0 : 0x0d0)
+#define HW_SSP_STATUS(h)			(ssp_is_old(h) ? 0x0c0 : 0x100)
+#define  BM_SSP_STATUS_CARD_DETECT		(1 << 28)
+#define  BM_SSP_STATUS_SDIO_IRQ			(1 << 17)
+
+#define BF_SSP(value, field)	(((value) << BP_SSP_##field) & BM_SSP_##field)
+
+#define SSP_PIO_NUM	3
+
+enum mxs_mmc_id {
+	IMX23_MMC,
+	IMX28_MMC,
+};
+
+#endif	/* __LINUX_SPI_MXS_SPI_H__ */
-- 
1.7.10


------------------------------------------------------------------------------
Live Security Virtual Conference
Exclusive live event will cover all the ways today's security and 
threat landscape has changed and how IT managers can respond. Discussions 
will include endpoint security, mobile security and the latest in malware 
threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/