Linux-SPI Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH V3] spi: Add HiSilicon SPI Controller Driver for Kunpeng SoCs
@ 2021-03-27  9:10 Jay Fang
  2021-04-01 10:16 ` Mark Brown
  0 siblings, 1 reply; 2+ messages in thread
From: Jay Fang @ 2021-03-27  9:10 UTC (permalink / raw)
  To: broonie, linux-spi; +Cc: huangdaode, linuxarm

This driver supports SPI Controller for HiSilicon Kunpeng SoCs. This
driver supports SPI operations using FIFO mode of transfer.

DMA is not supported, and we just use IRQ mode for operation completion
notification.

Only ACPI firmware is supported.

Signed-off-by: Jay Fang <f.fangjian@huawei.com>
---
Changes in v3:
- Update Kconfig symbol and filename.
Changes in v2:
- Use a more specific name (Kunpeng SoCs) for this driver.
- Remove interrupt mask/unmask/clear functions.
- Merge some tiny functions.
- Optimize the interrupt handling process.
- Add detailed comments for memory barrier.
- Use devm_spi_alloc_master() to allocte 'struct hisi_spi'.
---
 MAINTAINERS                    |   7 +
 drivers/spi/Kconfig            |  10 +
 drivers/spi/Makefile           |   1 +
 drivers/spi/spi-hisi-kunpeng.c | 505 +++++++++++++++++++++++++++++++++++++++++
 4 files changed, 523 insertions(+)
 create mode 100644 drivers/spi/spi-hisi-kunpeng.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 546aa66..ced2731 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8080,6 +8080,13 @@ F:	drivers/crypto/hisilicon/sec2/sec_crypto.c
 F:	drivers/crypto/hisilicon/sec2/sec_crypto.h
 F:	drivers/crypto/hisilicon/sec2/sec_main.c
 
+HISILICON SPI Controller DRIVER FOR KUNPENG SOCS
+M:	Jay Fang <f.fangjian@huawei.com>
+L:	linux-spi@vger.kernel.org
+S:	Maintained
+W:	http://www.hisilicon.com
+F:	drivers/spi/spi-hisi-kunpeng.c
+
 HISILICON STAGING DRIVERS FOR HIKEY 960/970
 M:	Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
 L:	devel@driverdev.osuosl.org
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index aadaea0..2e284ca 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -339,6 +339,16 @@ config SPI_FSL_QUADSPI
 	  This controller does not support generic SPI messages. It only
 	  supports the high-level SPI memory interface.
 
+config SPI_HISI_KUNPENG
+	tristate "HiSilicon SPI Controller for Kunpeng SoCs"
+	depends on (ARM64 && ACPI) || COMPILE_TEST
+	help
+	  This enables support for HiSilicon SPI controller found on
+	  Kunpeng SoCs.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called hisi-kunpeng-spi.
+
 config SPI_HISI_SFC_V3XX
 	tristate "HiSilicon SPI NOR Flash Controller for Hi16XX chipsets"
 	depends on (ARM64 && ACPI) || COMPILE_TEST
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 6fea582..04291ff 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -54,6 +54,7 @@ obj-$(CONFIG_SPI_FSL_LPSPI)		+= spi-fsl-lpspi.o
 obj-$(CONFIG_SPI_FSL_QUADSPI)		+= spi-fsl-qspi.o
 obj-$(CONFIG_SPI_FSL_SPI)		+= spi-fsl-spi.o
 obj-$(CONFIG_SPI_GPIO)			+= spi-gpio.o
+obj-$(CONFIG_SPI_HISI_KUNPENG)		+= spi-hisi-kunpeng.o
 obj-$(CONFIG_SPI_HISI_SFC_V3XX)		+= spi-hisi-sfc-v3xx.o
 obj-$(CONFIG_SPI_IMG_SPFI)		+= spi-img-spfi.o
 obj-$(CONFIG_SPI_IMX)			+= spi-imx.o
diff --git a/drivers/spi/spi-hisi-kunpeng.c b/drivers/spi/spi-hisi-kunpeng.c
new file mode 100644
index 00000000..abc0cd5
--- /dev/null
+++ b/drivers/spi/spi-hisi-kunpeng.c
@@ -0,0 +1,505 @@
+// SPDX-License-Identifier: GPL-2.0-only
+//
+// HiSilicon SPI Controller Driver for Kunpeng SoCs
+//
+// Copyright (c) 2021 HiSilicon Technologies Co., Ltd.
+// Author: Jay Fang <f.fangjian@huawei.com>
+//
+// This code is based on spi-dw-core.c.
+
+#include <linux/acpi.h>
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/property.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+
+/* Register offsets */
+#define HISI_SPI_CSCR		0x00	/* cs control register */
+#define HISI_SPI_CR		0x04	/* spi common control register */
+#define HISI_SPI_ENR		0x08	/* spi enable register */
+#define HISI_SPI_FIFOC		0x0c	/* fifo level control register */
+#define HISI_SPI_IMR		0x10	/* interrupt mask register */
+#define HISI_SPI_DIN		0x14	/* data in register */
+#define HISI_SPI_DOUT		0x18	/* data out register */
+#define HISI_SPI_SR		0x1c	/* status register */
+#define HISI_SPI_RISR		0x20	/* raw interrupt status register */
+#define HISI_SPI_ISR		0x24	/* interrupt status register */
+#define HISI_SPI_ICR		0x28	/* interrupt clear register */
+#define HISI_SPI_VERSION	0xe0	/* version register */
+
+/* Bit fields in HISI_SPI_CR */
+#define CR_LOOP_MASK		GENMASK(1, 1)
+#define CR_CPOL_MASK		GENMASK(2, 2)
+#define CR_CPHA_MASK		GENMASK(3, 3)
+#define CR_DIV_PRE_MASK		GENMASK(11, 4)
+#define CR_DIV_POST_MASK	GENMASK(19, 12)
+#define CR_BPW_MASK		GENMASK(24, 20)
+#define CR_SPD_MODE_MASK	GENMASK(25, 25)
+
+/* Bit fields in HISI_SPI_FIFOC */
+#define FIFOC_TX_MASK		GENMASK(5, 3)
+#define FIFOC_RX_MASK		GENMASK(11, 9)
+
+/* Bit fields in HISI_SPI_IMR, 4 bits */
+#define IMR_RXOF		BIT(0)		/* Receive Overflow */
+#define IMR_RXTO		BIT(1)		/* Receive Timeout */
+#define IMR_RX			BIT(2)		/* Receive */
+#define IMR_TX			BIT(3)		/* Transmit */
+#define IMR_MASK		(IMR_RXOF | IMR_RXTO | IMR_RX | IMR_TX)
+
+/* Bit fields in HISI_SPI_SR, 5 bits */
+#define SR_TXE			BIT(0)		/* Transmit FIFO empty */
+#define SR_TXNF			BIT(1)		/* Transmit FIFO not full */
+#define SR_RXNE			BIT(2)		/* Receive FIFO not empty */
+#define SR_RXF			BIT(3)		/* Receive FIFO full */
+#define SR_BUSY			BIT(4)		/* Busy Flag */
+
+/* Bit fields in HISI_SPI_ISR, 4 bits */
+#define ISR_RXOF		BIT(0)		/* Receive Overflow */
+#define ISR_RXTO		BIT(1)		/* Receive Timeout */
+#define ISR_RX			BIT(2)		/* Receive */
+#define ISR_TX			BIT(3)		/* Transmit */
+#define ISR_MASK		(ISR_RXOF | ISR_RXTO | ISR_RX | ISR_TX)
+
+/* Bit fields in HISI_SPI_ICR, 2 bits */
+#define ICR_RXOF		BIT(0)		/* Receive Overflow */
+#define ICR_RXTO		BIT(1)		/* Receive Timeout */
+#define ICR_MASK		(ICR_RXOF | ICR_RXTO)
+
+#define DIV_POST_MAX		0xFF
+#define DIV_POST_MIN		0x00
+#define DIV_PRE_MAX		0xFE
+#define DIV_PRE_MIN		0x02
+#define CLK_DIV_MAX		((1 + DIV_POST_MAX) * DIV_PRE_MAX)
+#define CLK_DIV_MIN		((1 + DIV_POST_MIN) * DIV_PRE_MIN)
+
+#define DEFAULT_NUM_CS		1
+
+#define HISI_SPI_WAIT_TIMEOUT_MS	10UL
+
+enum hisi_spi_rx_level_trig {
+	HISI_SPI_RX_1,
+	HISI_SPI_RX_4,
+	HISI_SPI_RX_8,
+	HISI_SPI_RX_16,
+	HISI_SPI_RX_32,
+	HISI_SPI_RX_64,
+	HISI_SPI_RX_128
+};
+
+enum hisi_spi_tx_level_trig {
+	HISI_SPI_TX_1_OR_LESS,
+	HISI_SPI_TX_4_OR_LESS,
+	HISI_SPI_TX_8_OR_LESS,
+	HISI_SPI_TX_16_OR_LESS,
+	HISI_SPI_TX_32_OR_LESS,
+	HISI_SPI_TX_64_OR_LESS,
+	HISI_SPI_TX_128_OR_LESS
+};
+
+enum hisi_spi_frame_n_bytes {
+	HISI_SPI_N_BYTES_NULL,
+	HISI_SPI_N_BYTES_U8,
+	HISI_SPI_N_BYTES_U16,
+	HISI_SPI_N_BYTES_U32 = 4
+};
+
+/* Slave spi_dev related */
+struct hisi_chip_data {
+	u32 cr;
+	u32 speed_hz;	/* baud rate */
+	u16 clk_div;	/* baud rate divider */
+
+	/* clk_div = (1 + div_post) * div_pre */
+	u8 div_post;	/* value from 0 to 255 */
+	u8 div_pre;	/* value from 2 to 254 (even only!) */
+};
+
+struct hisi_spi {
+	struct device		*dev;
+
+	void __iomem		*regs;
+	int			irq;
+	u32			fifo_len; /* depth of the FIFO buffer */
+
+	/* Current message transfer state info */
+	const void		*tx;
+	unsigned int		tx_len;
+	void			*rx;
+	unsigned int		rx_len;
+	u8			n_bytes; /* current is a 1/2/4 bytes op */
+};
+
+static u32 hisi_spi_busy(struct hisi_spi *hs)
+{
+	return readl(hs->regs + HISI_SPI_SR) & SR_BUSY;
+}
+
+static u32 hisi_spi_rx_not_empty(struct hisi_spi *hs)
+{
+	return readl(hs->regs + HISI_SPI_SR) & SR_RXNE;
+}
+
+static u32 hisi_spi_tx_not_full(struct hisi_spi *hs)
+{
+	return readl(hs->regs + HISI_SPI_SR) & SR_TXNF;
+}
+
+static void hisi_spi_flush_fifo(struct hisi_spi *hs)
+{
+	unsigned long limit = loops_per_jiffy << 1;
+
+	do {
+		while (hisi_spi_rx_not_empty(hs))
+			readl(hs->regs + HISI_SPI_DOUT);
+	} while (hisi_spi_busy(hs) && limit--);
+}
+
+/* Disable the controller and all interrupts */
+static void hisi_spi_disable(struct hisi_spi *hs)
+{
+	writel(0, hs->regs + HISI_SPI_ENR);
+	writel(IMR_MASK, hs->regs + HISI_SPI_IMR);
+	writel(ICR_MASK, hs->regs + HISI_SPI_ICR);
+}
+
+static u8 hisi_spi_n_bytes(struct spi_transfer *transfer)
+{
+	if (transfer->bits_per_word <= 8)
+		return HISI_SPI_N_BYTES_U8;
+	else if (transfer->bits_per_word <= 16)
+		return HISI_SPI_N_BYTES_U16;
+	else
+		return HISI_SPI_N_BYTES_U32;
+}
+
+static void hisi_spi_reader(struct hisi_spi *hs)
+{
+	u32 max = min_t(u32, hs->rx_len, hs->fifo_len);
+	u32 rxw;
+
+	while (hisi_spi_rx_not_empty(hs) && max--) {
+		rxw = readl(hs->regs + HISI_SPI_DOUT);
+		/* Check the transfer's original "rx" is not null */
+		if (hs->rx) {
+			switch (hs->n_bytes) {
+			case HISI_SPI_N_BYTES_U8:
+				*(u8 *)(hs->rx) = rxw;
+				break;
+			case HISI_SPI_N_BYTES_U16:
+				*(u16 *)(hs->rx) = rxw;
+				break;
+			case HISI_SPI_N_BYTES_U32:
+				*(u32 *)(hs->rx) = rxw;
+				break;
+			}
+			hs->rx += hs->n_bytes;
+		}
+		--hs->rx_len;
+	}
+}
+
+static void hisi_spi_writer(struct hisi_spi *hs)
+{
+	u32 max = min_t(u32, hs->tx_len, hs->fifo_len);
+	u32 txw = 0;
+
+	while (hisi_spi_tx_not_full(hs) && max--) {
+		/* Check the transfer's original "tx" is not null */
+		if (hs->tx) {
+			switch (hs->n_bytes) {
+			case HISI_SPI_N_BYTES_U8:
+				txw = *(u8 *)(hs->tx);
+				break;
+			case HISI_SPI_N_BYTES_U16:
+				txw = *(u16 *)(hs->tx);
+				break;
+			case HISI_SPI_N_BYTES_U32:
+				txw = *(u32 *)(hs->tx);
+				break;
+			}
+			hs->tx += hs->n_bytes;
+		}
+		writel(txw, hs->regs + HISI_SPI_DIN);
+		--hs->tx_len;
+	}
+}
+
+static void __hisi_calc_div_reg(struct hisi_chip_data *chip)
+{
+	chip->div_pre = DIV_PRE_MAX;
+	while (chip->div_pre >= DIV_PRE_MIN) {
+		if (chip->clk_div % chip->div_pre == 0)
+			break;
+
+		chip->div_pre -= 2;
+	}
+
+	if (chip->div_pre > chip->clk_div)
+		chip->div_pre = chip->clk_div;
+
+	chip->div_post = (chip->clk_div / chip->div_pre) - 1;
+}
+
+static u32 hisi_calc_effective_speed(struct spi_controller *master,
+			struct hisi_chip_data *chip, u32 speed_hz)
+{
+	u32 effective_speed;
+
+	/* Note clock divider doesn't support odd numbers */
+	chip->clk_div = DIV_ROUND_UP(master->max_speed_hz, speed_hz) + 1;
+	chip->clk_div &= 0xfffe;
+	if (chip->clk_div > CLK_DIV_MAX)
+		chip->clk_div = CLK_DIV_MAX;
+
+	effective_speed = master->max_speed_hz / chip->clk_div;
+	if (chip->speed_hz != effective_speed) {
+		__hisi_calc_div_reg(chip);
+		chip->speed_hz = effective_speed;
+	}
+
+	return effective_speed;
+}
+
+static u32 hisi_spi_prepare_cr(struct spi_device *spi)
+{
+	u32 cr = FIELD_PREP(CR_SPD_MODE_MASK, 1);
+
+	cr |= FIELD_PREP(CR_CPHA_MASK, (spi->mode & SPI_CPHA) ? 1 : 0);
+	cr |= FIELD_PREP(CR_CPOL_MASK, (spi->mode & SPI_CPOL) ? 1 : 0);
+	cr |= FIELD_PREP(CR_LOOP_MASK, (spi->mode & SPI_LOOP) ? 1 : 0);
+
+	return cr;
+}
+
+static void hisi_spi_hw_init(struct hisi_spi *hs)
+{
+	hisi_spi_disable(hs);
+
+	/* FIFO default config */
+	writel(FIELD_PREP(FIFOC_TX_MASK, HISI_SPI_TX_64_OR_LESS) |
+		FIELD_PREP(FIFOC_RX_MASK, HISI_SPI_RX_16),
+		hs->regs + HISI_SPI_FIFOC);
+
+	hs->fifo_len = 256;
+}
+
+static irqreturn_t hisi_spi_irq(int irq, void *dev_id)
+{
+	struct spi_controller *master = dev_id;
+	struct hisi_spi *hs = spi_controller_get_devdata(master);
+	u32 irq_status = readl(hs->regs + HISI_SPI_ISR) & ISR_MASK;
+
+	if (!irq_status)
+		return IRQ_NONE;
+
+	if (!master->cur_msg)
+		return IRQ_HANDLED;
+
+	/* Error handling */
+	if (irq_status & ISR_RXOF) {
+		dev_err(hs->dev, "interrupt_transfer: fifo overflow\n");
+		master->cur_msg->status = -EIO;
+		goto finalize_transfer;
+	}
+
+	/*
+	 * Read data from the Rx FIFO every time. If there is
+	 * nothing left to receive, finalize the transfer.
+	 */
+	hisi_spi_reader(hs);
+	if (!hs->rx_len)
+		goto finalize_transfer;
+
+	/* Send data out when Tx FIFO IRQ triggered */
+	if (irq_status & ISR_TX)
+		hisi_spi_writer(hs);
+
+	return IRQ_HANDLED;
+
+finalize_transfer:
+	hisi_spi_disable(hs);
+	spi_finalize_current_transfer(master);
+	return IRQ_HANDLED;
+}
+
+static int hisi_spi_transfer_one(struct spi_controller *master,
+		struct spi_device *spi, struct spi_transfer *transfer)
+{
+	struct hisi_spi *hs = spi_controller_get_devdata(master);
+	struct hisi_chip_data *chip = spi_get_ctldata(spi);
+	u32 cr = chip->cr;
+
+	/* Update per transfer options for speed and bpw */
+	transfer->effective_speed_hz =
+		hisi_calc_effective_speed(master, chip, transfer->speed_hz);
+	cr |= FIELD_PREP(CR_DIV_PRE_MASK, chip->div_pre);
+	cr |= FIELD_PREP(CR_DIV_POST_MASK, chip->div_post);
+	cr |= FIELD_PREP(CR_BPW_MASK, transfer->bits_per_word - 1);
+	writel(cr, hs->regs + HISI_SPI_CR);
+
+	hisi_spi_flush_fifo(hs);
+
+	hs->n_bytes = hisi_spi_n_bytes(transfer);
+	hs->tx = transfer->tx_buf;
+	hs->tx_len = transfer->len / hs->n_bytes;
+	hs->rx = transfer->rx_buf;
+	hs->rx_len = hs->tx_len;
+
+	/*
+	 * Ensure that the transfer data above has been updated
+	 * before the interrupt to start.
+	 */
+	smp_mb();
+
+	/* Enable all interrupts and the controller */
+	writel(~IMR_MASK, hs->regs + HISI_SPI_IMR);
+	writel(1, hs->regs + HISI_SPI_ENR);
+
+	return 1;
+}
+
+static void hisi_spi_handle_err(struct spi_controller *master,
+		struct spi_message *msg)
+{
+	struct hisi_spi *hs = spi_controller_get_devdata(master);
+
+	hisi_spi_disable(hs);
+
+	/*
+	 * Wait for interrupt handler that is
+	 * already in timeout to complete.
+	 */
+	msleep(HISI_SPI_WAIT_TIMEOUT_MS);
+}
+
+static int hisi_spi_setup(struct spi_device *spi)
+{
+	struct hisi_chip_data *chip;
+
+	/* Only alloc on first setup */
+	chip = spi_get_ctldata(spi);
+	if (!chip) {
+		chip = kzalloc(sizeof(*chip), GFP_KERNEL);
+		if (!chip)
+			return -ENOMEM;
+		spi_set_ctldata(spi, chip);
+	}
+
+	chip->cr = hisi_spi_prepare_cr(spi);
+
+	return 0;
+}
+
+static void hisi_spi_cleanup(struct spi_device *spi)
+{
+	struct hisi_chip_data *chip = spi_get_ctldata(spi);
+
+	kfree(chip);
+	spi_set_ctldata(spi, NULL);
+}
+
+static int hisi_spi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct spi_controller *master;
+	struct hisi_spi *hs;
+	int ret, irq;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	master = devm_spi_alloc_master(dev, sizeof(*hs));
+	if (!master)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, master);
+
+	hs = spi_controller_get_devdata(master);
+	hs->dev = dev;
+	hs->irq = irq;
+
+	hs->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(hs->regs))
+		return PTR_ERR(hs->regs);
+
+	/* Specify maximum SPI clocking speed (master only) by firmware */
+	ret = device_property_read_u32(dev, "spi-max-frequency",
+					&master->max_speed_hz);
+	if (ret) {
+		dev_err(dev, "failed to get max SPI clocking speed, ret=%d\n",
+			ret);
+		return -EINVAL;
+	}
+
+	ret = device_property_read_u16(dev, "num-cs",
+					&master->num_chipselect);
+	if (ret)
+		master->num_chipselect = DEFAULT_NUM_CS;
+
+	master->use_gpio_descriptors = true;
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
+	master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
+	master->bus_num = pdev->id;
+	master->setup = hisi_spi_setup;
+	master->cleanup = hisi_spi_cleanup;
+	master->transfer_one = hisi_spi_transfer_one;
+	master->handle_err = hisi_spi_handle_err;
+	master->dev.fwnode = dev->fwnode;
+
+	hisi_spi_hw_init(hs);
+
+	ret = devm_request_irq(dev, hs->irq, hisi_spi_irq, 0, dev_name(dev),
+			master);
+	if (ret < 0) {
+		dev_err(dev, "failed to get IRQ=%d, ret=%d\n", hs->irq, ret);
+		return ret;
+	}
+
+	ret = spi_register_controller(master);
+	if (ret) {
+		dev_err(dev, "failed to register spi master, ret=%d\n", ret);
+		return ret;
+	}
+
+	dev_info(dev, "hw version:0x%x max-freq:%u kHz\n",
+		readl(hs->regs + HISI_SPI_VERSION),
+		master->max_speed_hz / 1000);
+
+	return 0;
+}
+
+static int hisi_spi_remove(struct platform_device *pdev)
+{
+	struct spi_controller *master = platform_get_drvdata(pdev);
+
+	spi_unregister_controller(master);
+
+	return 0;
+}
+
+static const struct acpi_device_id hisi_spi_acpi_match[] = {
+	{"HISI03E1", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(acpi, hisi_spi_acpi_match);
+
+static struct platform_driver hisi_spi_driver = {
+	.probe		= hisi_spi_probe,
+	.remove		= hisi_spi_remove,
+	.driver		= {
+		.name	= "hisi-kunpeng-spi",
+		.acpi_match_table = hisi_spi_acpi_match,
+	},
+};
+module_platform_driver(hisi_spi_driver);
+
+MODULE_AUTHOR("Jay Fang <f.fangjian@huawei.com>");
+MODULE_DESCRIPTION("HiSilicon SPI Controller Driver for Kunpeng SoCs");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4


^ permalink raw reply	[flat|nested] 2+ messages in thread

* Re: [PATCH V3] spi: Add HiSilicon SPI Controller Driver for Kunpeng SoCs
  2021-03-27  9:10 [PATCH V3] spi: Add HiSilicon SPI Controller Driver for Kunpeng SoCs Jay Fang
@ 2021-04-01 10:16 ` Mark Brown
  0 siblings, 0 replies; 2+ messages in thread
From: Mark Brown @ 2021-04-01 10:16 UTC (permalink / raw)
  To: linux-spi, Jay Fang; +Cc: Mark Brown, linuxarm, huangdaode

On Sat, 27 Mar 2021 17:10:00 +0800, Jay Fang wrote:
> This driver supports SPI Controller for HiSilicon Kunpeng SoCs. This
> driver supports SPI operations using FIFO mode of transfer.
> 
> DMA is not supported, and we just use IRQ mode for operation completion
> notification.
> 
> Only ACPI firmware is supported.

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[1/1] spi: Add HiSilicon SPI Controller Driver for Kunpeng SoCs
      commit: c770d8631e1810d8f1ce21b18ad5dd67eeb39e5c

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, back to index

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-03-27  9:10 [PATCH V3] spi: Add HiSilicon SPI Controller Driver for Kunpeng SoCs Jay Fang
2021-04-01 10:16 ` Mark Brown

Linux-SPI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-spi/0 linux-spi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-spi linux-spi/ https://lore.kernel.org/linux-spi \
		linux-spi@vger.kernel.org
	public-inbox-index linux-spi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-spi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git