From mboxrd@z Thu Jan 1 00:00:00 1970 From: Konrad Kociolek Subject: [PATCH 1/2] spi: Add dt-bindings schema for Cadence XSPI controller driver Date: Mon, 20 Jan 2020 13:54:31 +0100 Message-ID: <20200120125443.9523-1-konrad@cadence.com> Mime-Version: 1.0 Content-Type: text/plain Cc: Konrad Kociolek , Mark Brown , Rob Herring , Mark Rutland , , , To: unlisted-recipients:; (no To-header on input) Return-path: Sender: linux-kernel-owner@vger.kernel.org List-Id: linux-spi.vger.kernel.org Add dt-bindings documentation for Cadence XSPI controller to support SPI based flash memories. Signed-off-by: Konrad Kociolek --- .../devicetree/bindings/spi/cdns,xspi.yaml | 164 +++++++++++++++++++++ 1 file changed, 164 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/cdns,xspi.yaml diff --git a/Documentation/devicetree/bindings/spi/cdns,xspi.yaml b/Documentation/devicetree/bindings/spi/cdns,xspi.yaml new file mode 100644 index 0000000..2d6a362 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/cdns,xspi.yaml @@ -0,0 +1,164 @@ +# SPDX-License-Identifier: (GPL-2.0) +# Copyright 2020 Cadence +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/spi/cadence,xspi.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Cadence XSPI Controller + +maintainers: + - Konrad Kociolek + +description: | + The XSPI controller allows SPI protocol communication in + single, dual, quad or octal wire transmission modes for + read/write access to slaves such as SPI-NOR flash. + +properties: + compatible: + const: cdns,xspi-nor-fpga + + reg: + maxItems: 3 + description: | + Contains three entries, each of which is a tuple consisting of a + physical address and length. The first entry is the address and + length of the controller register set. The second entry is the + address and length of the Slave DMA data port. The third entry is + the address and length of auxiliary registers. + + interrupts: + maxItems: 1 + + cdns,dqs-last-data-drop: + type: boolean + description: | + This parameter should be set when the Flash Device being used + issues data on negative edge of Flash clock and returns them with + DQS and the PHY is configured to sample data in DQS mode. + If this param is set the controller internally requests this redundant + data at the end of the transfer cleaning up the PHY FIFO. + + cdns,phy-data-select-oe-start: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Adjusts the starting point of the DQ pad output enable window. + Lower numbers pull the rising edge earlier in time and larger + numbers cause the rising edge to be delayed. Each bit changes + the output enable time by a 1/2 cycle resolution. + + cdns,phy-data-select-oe-end: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Adjusts the ending point of the DQ pad output enable window. + Lower numbers pull the falling edge earlier in time and larger + numbers cause the falling edge to be delayed. Each bit changes + the output enable time by a 1/2 cycle resolution. + + cdns,phy-dqs-select-oe-start: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Adjusts the starting point of the DQS pad output enable window. + Lower numbers pull the rising edge earlier in time and larger + numbers cause the rising edge to be delayed. Each bit changes + the output enable time by a 1/2 cycle resolution. + + cdns,phy-dqs-select-oe-end: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Adjusts the ending point of the DQS pad output enable window. + Lower numbers pull the falling edge earlier in time and larger + numbers cause the falling edge to be delayed. Each bit changes + the output enable time by a 1/2 cycle resolution. + + cdns,phy-gate-cfg-close: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Normally the gate is closing then all bits of dfi_cebar are high + or when dfi_rd_pre_post_amble and rebar_dfi are high. This parameter + allows to extend the closing of the DQS gate. Recommended zero. + + cdns,phy-gate-cfg: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Coarse adjust of gate open time. This value is the number of cycles + to delay the dfi_rddata_en signal prior to opening the gate in + full cycle increments. Decreasing this value pulls the gate earlier + in time. This field should be programmed such that the gate signal + lands in the valid DQS gate window. + + cdns,phy-rd-del-select: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Defines the read data delay. Holds the number of cycles to delay + the dfi_rddata_en signal prior to enabling the read FIFO. + After this delay, the read pointers begin incrementing the read FIFO. + + cdns,phy-clk-wr-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Controls the clk_wr delay line which adjusts the write DQ bit + timing in 1/256th steps of the clock period in normal DLL + locked mode. In bypass mode this field directly programs + the number of delay elements. + + cdns,phy-use-lpbk-dqs: + type: boolean + description: | + This parameter chooses lpbk_dqs to capture data for reads. + Instead memory DQS will be used. + + cdns,phy-use-ext-lpbk-dqs: + type: boolean + description: | + This parameter chooses external lpbk_dqs for data capture + (lpbk_dqs connected to the lpbk_dqs_IO pad). When not used + mem_rebar_pad is used for data read capture. + +required: + - compatible + - reg + - interrupts + - cdns,phy-data-select-oe-start + - cdns,phy-data-select-oe-end + - cdns,phy-dqs-select-oe-start + - cdns,phy-dqs-select-oe-end + - cdns,phy-gate-cfg-close + - cdns,phy-gate-cfg + - cdns,phy-rd-del-select + - cdns,phy-clk-wr-delay + +examples: + - | + xspi: spi@a0010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cdns,xspi-nor-fpga"; + reg = <0x0 0xa0010000 0x0 0x10000>, + <0x0 0xb0000000 0x0 0x10000>, + <0x0 0xa0020000 0x0 0x10000>; + interrupts = <0 90 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gic>; + cdns,dqs-last-data-drop; + cdns,phy-data-select-oe-start = <0>; + cdns,phy-data-select-oe-end = <4>; + cdns,phy-dqs-select-oe-start = <0>; + cdns,phy-dqs-select-oe-end = <1>; + cdns,phy-gate-cfg-close = <3>; + cdns,phy-gate-cfg = <0>; + cdns,phy-rd-del-select = <5>; + cdns,phy-clk-wr-delay = <64>; + cdns,phy-use-lpbk-dqs; + cdns,phy-use-ext-lpbk-dqs; + mt35xu512@0 { + compatible = "spi-nor", "micron,mt35xu512"; + spi-max-frequency = <75000000>; + reg = <0>; + }; + mt35xu512@1 { + compatible = "spi-nor", "micron,mt35xu512"; + spi-max-frequency = <75000000>; + reg = <1>; + }; + }; -- 2.7.4