linux-spi.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Chris Packham <chris.packham-6g8wRflRTwXFdCa3tKVlE6U/zSkkHjvu@public.gmane.org>
To: broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	mark.rutland-5wv7dgnIgG8@public.gmane.org
Cc: linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	Chris Packham
	<chris.packham-6g8wRflRTwXFdCa3tKVlE6U/zSkkHjvu@public.gmane.org>
Subject: [PATCH v2 1/2] dt-bindings: spi: Document binding for generic SPI multiplexer
Date: Thu, 23 Jan 2020 14:23:16 +1300	[thread overview]
Message-ID: <20200123012317.14808-2-chris.packham@alliedtelesis.co.nz> (raw)
In-Reply-To: <20200123012317.14808-1-chris.packham-6g8wRflRTwXFdCa3tKVlE6U/zSkkHjvu@public.gmane.org>

Add binding documentation for the spi-mux driver. This allows a generic
multiplexer to be used to provide access to multiple SPI devices.

Signed-off-by: Chris Packham <chris.packham-6g8wRflRTwXFdCa3tKVlE6U/zSkkHjvu@public.gmane.org>
---

Notes:
    Changes in v2:
    - update license
    - make dt_binding_check clean

 .../devicetree/bindings/spi/spi-mux.yaml      | 84 +++++++++++++++++++
 1 file changed, 84 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/spi-mux.yaml

diff --git a/Documentation/devicetree/bindings/spi/spi-mux.yaml b/Documentation/devicetree/bindings/spi/spi-mux.yaml
new file mode 100644
index 000000000000..4bdb31e2257e
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-mux.yaml
@@ -0,0 +1,84 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/spi-mux.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic SPI Multiplexer
+
+description: |
+  This binding describes a SPI bus multiplexer to route the SPI chip select
+  signals. This can be used when you need more devices than the SPI controller
+  has chip selects available. An example setup is shown in ASCII art; the actual
+  setting of the multiplexer to a channel needs to be done by a specific SPI mux
+  driver.
+
+        MOSI /--------------------------------+--------+--------+--------\
+        MISO |/------------------------------+|-------+|-------+|-------\|
+         SCL ||/----------------------------+||------+||------+||------\||
+             |||                            |||      |||      |||      |||
+      +------------+                        |||      |||      |||      |||
+      | SoC  |||   |                      +-+++-+  +-+++-+  +-+++-+  +-+++-+
+      |      |||   |                      | dev |  | dev |  | dev |  | dev |
+      |   +--+++-+ | CS-X  +------+\      +--+--+  +--+--+  +--+--+  +--+--+
+      |   | SPI  +-|-------+ Mux  |\\   CS-0 |        |        |        |
+      |   +------+ |       +--+---+\\\-------/   CS-1 |        |        |
+      |            |          |    \\\----------------/   CS-2 |        |
+      |   +------+ |          |     \\-------------------------/   CS-3 |
+      |   | ?    +-|----------/      \----------------------------------/
+      |   +------+ |
+      +------------+
+
+allOf:
+  - $ref: "/schemas/spi/spi-controller.yaml#"
+
+maintainers:
+  - Chris Packham <chris.packham-6g8wRflRTwXFdCa3tKVlE6U/zSkkHjvu@public.gmane.org>
+
+properties:
+  compatible:
+    const: spi-mux
+
+  mux-controls:
+    maxItems: 1
+
+required:
+   - compatible
+   - reg
+   - spi-max-frequency
+   - mux-controls
+
+examples:
+   - |
+     mux: mux-controller {
+       compatible = "gpio-mux";
+       #mux-control-cells = <0>;
+
+       mux-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+     };
+
+     spi {
+       spi-mux@0 {
+         compatible = "spi-mux";
+         #address-cells = <1>;
+         #size-cells = <0>;
+         reg = <0>;
+         spi-max-frequency = <100000000>;
+
+         mux-controls = <&mux>
+
+         spi-flash@0 {
+           compatible = "jedec,spi-nor";
+           #address-cells = <1>;
+           #size-cells = <1>;
+           reg = <0>;
+           spi-max-frequency = <40000000>;
+         };
+
+         spi-device@1 {
+           compatible = "lineartechnology,ltc2488";
+           reg = <1>;
+           spi-max-frequency = <10000000>;
+         };
+       };
+     };
-- 
2.25.0

  parent reply	other threads:[~2020-01-23  1:23 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-01-23  1:23 [PATCH v2 0/2] SPI bus multiplexing Chris Packham
     [not found] ` <20200123012317.14808-1-chris.packham-6g8wRflRTwXFdCa3tKVlE6U/zSkkHjvu@public.gmane.org>
2020-01-23  1:23   ` Chris Packham [this message]
2020-01-23 13:51     ` [PATCH v2 1/2] dt-bindings: spi: Document binding for generic SPI multiplexer Rob Herring
     [not found]       ` <CAL_JsqLvM34WSBE29beBgJj0jLA6P_UwQUbTuEQcYJgrkg3v1A-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2020-01-26 20:23         ` Chris Packham
2020-01-27 13:56           ` Rob Herring
2020-01-23  1:23   ` [PATCH v2 2/2] spi: Add " Chris Packham

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200123012317.14808-2-chris.packham@alliedtelesis.co.nz \
    --to=chris.packham-6g8wrflrtwxfdca3tkvle6u/zskkhjvu@public.gmane.org \
    --cc=broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
    --cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
    --cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).