linux-spi.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Pratyush Yadav <p.yadav@ti.com>
To: Tudor Ambarus <tudor.ambarus@microchip.com>,
	Miquel Raynal <miquel.raynal@bootlin.com>,
	Richard Weinberger <richard@nod.at>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Mark Brown <broonie@kernel.org>
Cc: <linux-mtd@lists.infradead.org>, <linux-kernel@vger.kernel.org>,
	<linux-spi@vger.kernel.org>, Sekhar Nori <nsekhar@ti.com>,
	Pratyush Yadav <p.yadav@ti.com>
Subject: [PATCH 9/9] mtd: spi-nor: add support for Cypress Semper flash
Date: Tue, 11 Feb 2020 19:03:48 +0530	[thread overview]
Message-ID: <20200211133348.15558-10-p.yadav@ti.com> (raw)
In-Reply-To: <20200211133348.15558-1-p.yadav@ti.com>

The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.

The flash by default boots in a hybrid sector mode. Switch to uniform
sector mode on boot. Use the default 20 dummy cycles for a read fast
command.

The SFDP programming on some older versions of the flash was incorrect.
Fixes for that are included in the fixup hooks.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/mtd/spi-nor/spi-nor.c | 192 ++++++++++++++++++++++++++++++++++
 include/linux/mtd/spi-nor.h   |  14 +++
 2 files changed, 206 insertions(+)

diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 78e3475fa2a9..367e3d0f65aa 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -260,6 +260,12 @@ struct flash_info {
 
 #define JEDEC_MFR(info)	((info)->id[0])
 
+/* Forward declarations that will be used by s28hs512t_setup(). */
+static int spi_nor_default_setup(struct spi_nor *nor,
+				 const struct spi_nor_hwcaps *hwcaps);
+static void spi_nor_set_pp_settings(struct spi_nor_pp_command *pp,
+				    u8 opcode, enum spi_nor_protocol proto);
+
 /**
  * spi_nor_spimem_setup_op() - Set up common properties of a spi-mem op.
  * @nor:		pointer to a 'struct spi_nor'
@@ -2241,6 +2247,65 @@ static int spi_nor_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 	return ret;
 }
 
+/**
+ * spi_nor_cypress_octal_enable() - Enable octal DTR mode on Cypress flashes.
+ * @nor:		pointer to a 'struct spi_nor'
+ *
+ * This also sets the memory access latency cycles to 20, which is the default
+ * in the spi-nor framework.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_cypress_octal_enable(struct spi_nor *nor)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	u8 addr_width = 3;
+	int ret;
+
+	/* Use 20 dummy cycles for memory array reads. */
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	*buf = SPINOR_REG_CYPRESS_CFR2V_MEMLAT_8_20;
+	op = (struct spi_mem_op)SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+			SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR2V, 1),
+			SPI_MEM_OP_NO_DUMMY,
+			SPI_MEM_OP_DATA_OUT(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret) {
+		dev_warn(nor->dev,
+			 "failed to set default memory latency value: %d\n",
+			 ret);
+		return ret;
+	}
+	ret = spi_nor_wait_till_ready(nor);
+	if (ret)
+		return ret;
+
+	nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].num_wait_states = 20;
+	nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].num_mode_clocks = 0;
+
+	/* Set the octal and DTR enable bits. */
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	*buf = SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN;
+	op = (struct spi_mem_op)SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+			SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR5V, 1),
+			SPI_MEM_OP_NO_DUMMY,
+			SPI_MEM_OP_DATA_OUT(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret) {
+		dev_warn(nor->dev, "Failed to enable octal DTR mode\n");
+		return ret;
+	}
+
+	return 0;
+}
+
 /**
  * spi_nor_sr1_bit6_quad_enable() - Set the Quad Enable BIT(6) in the Status
  * Register 1.
@@ -2453,6 +2518,130 @@ static struct spi_nor_fixups gd25q256_fixups = {
 	.default_init = gd25q256_default_init,
 };
 
+static int s28hs512t_setup(struct spi_nor *nor,
+			    const struct spi_nor_hwcaps *hwcaps)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	u8 addr_width = 3;
+	int ret;
+
+	if (!nor->spimem) {
+		dev_err(nor->dev,
+			"operation not supported for non-spimem drivers\n");
+		return -ENOTSUPP;
+	}
+
+	/*
+	 * This Cypress flash also supports hybrid sector sizes. Make sure
+	 * uniform sector mode is selected. This is done by setting the bit
+	 * CFR3N[3].
+	 */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RD_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR3N, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_IN(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	ret = spi_nor_write_enable(nor);
+	if (ret)
+		return ret;
+
+	/* Set the uniform sector mode bit. */
+	*buf |= SPINOR_REG_CYPRESS_CFR3N_UNISECT;
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WR_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR3N, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_OUT(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret) {
+		dev_err(nor->dev, "Failed to change to uniform sector mode\n");
+		return ret;
+	}
+
+	ret = spi_nor_wait_till_ready(nor);
+	if (ret)
+		return ret;
+
+	return spi_nor_default_setup(nor, hwcaps);
+}
+
+static void s28hs512t_default_init(struct spi_nor *nor)
+{
+	nor->params.octal_dtr_enable = spi_nor_cypress_octal_enable;
+	nor->params.setup = s28hs512t_setup;
+}
+
+static void s28hs512t_post_sfdp_fixup(struct spi_nor *nor)
+{
+	/*
+	 * On older versions of the flash the xSPI Profile 1.0 table has the
+	 * 8D-8D-8D Fast Read opcode as 0x00. But it actually should be 0xEE.
+	 */
+	if (nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].opcode == 0)
+		nor->params.reads[SNOR_CMD_READ_8_8_8_DTR].opcode =
+			SPINOR_OP_CYPRESS_RD_FAST;
+
+	/* This flash is also missing the 4-byte Page Program opcode bit. */
+	spi_nor_set_pp_settings(&nor->params.page_programs[SNOR_CMD_PP],
+				SPINOR_OP_PP_4B, SNOR_PROTO_1_1_1);
+	/*
+	 * Since xSPI Page Program opcode is backward compatible with
+	 * Legacy SPI, use Legacy SPI opcode there as well.
+	 */
+	spi_nor_set_pp_settings(&nor->params.page_programs[SNOR_CMD_PP_8_8_8_DTR],
+				SPINOR_OP_PP_4B, SNOR_PROTO_8_8_8_DTR);
+
+	/*
+	 * The xSPI Profile 1.0 table advertises the number of additional
+	 * address bytes needed for Read Status Register command as 0 but the
+	 * actual value for that is 4.
+	 */
+	nor->params.rdsr_addr_nbytes = 4;
+}
+
+static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor,
+				     const struct sfdp_parameter_header *bfpt_header,
+				     const struct sfdp_bfpt *bfpt,
+				     struct spi_nor_flash_parameter *params)
+{
+	struct spi_mem_op op;
+	u8 *buf = nor->bouncebuf;
+	u8 addr_width = 3;
+	int ret;
+
+	/*
+	 * The BFPT table advertises a 512B page size but the page size is
+	 * actually configurable (with the default being 256B). Read from
+	 * CFR3V[4] and set the correct size.
+	 */
+	op = (struct spi_mem_op)
+		SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RD_ANY_REG, 1),
+			   SPI_MEM_OP_ADDR(addr_width, SPINOR_REG_CYPRESS_CFR3V, 1),
+			   SPI_MEM_OP_NO_DUMMY,
+			   SPI_MEM_OP_DATA_IN(1, buf, 1));
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret)
+		return ret;
+
+	if (*buf & SPINOR_REG_CYPRESS_CFR3V_PGSZ)
+		params->page_size = 512;
+	else
+		params->page_size = 256;
+
+	return 0;
+}
+
+static struct spi_nor_fixups s28hs512t_fixups = {
+	.default_init = s28hs512t_default_init,
+	.post_sfdp = s28hs512t_post_sfdp_fixup,
+	.post_bfpt = s28hs512t_post_bfpt_fixup,
+};
+
 /* NOTE: double check command sets and memory organization when you add
  * more nor chips.  This current list focusses on newer chips, which
  * have been converging on command sets which including JEDEC ID.
@@ -2715,6 +2904,9 @@ static const struct flash_info spi_nor_ids[] = {
 	{ "s25fl064l",  INFO(0x016017,      0,  64 * 1024, 128, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
 	{ "s25fl128l",  INFO(0x016018,      0,  64 * 1024, 256, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
 	{ "s25fl256l",  INFO(0x016019,      0,  64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
+	{ "s28hs512t",  INFO(0x345b1a,      0, 256 * 1024, 256, SECT_4K | SPI_NOR_OCTAL_DTR_READ)
+		.fixups = &s28hs512t_fixups,
+	},
 
 	/* SST -- large erase sizes are "overlays", "sectors" are 4K */
 	{ "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024,  8, SECT_4K | SST_WRITE) },
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index c653f6713cfc..e765272fc0f4 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -150,6 +150,20 @@
 #define SR2_QUAD_EN_BIT1	BIT(1)
 #define SR2_QUAD_EN_BIT7	BIT(7)
 
+/* For Cypress flash. */
+#define SPINOR_OP_RD_ANY_REG			0x65	/* Read any register */
+#define SPINOR_OP_WR_ANY_REG			0x71	/* Write any register */
+#define SPINOR_REG_CYPRESS_CFR2V		0x00800003
+#define SPINOR_REG_CYPRESS_CFR2V_MEMLAT_8_20	0x8
+#define SPINOR_REG_CYPRESS_CFR3N		0x00000004
+#define SPINOR_REG_CYPRESS_CFR3V		0x00800004
+#define SPINOR_REG_CYPRESS_CFR3V_PGSZ		BIT(4) /* Page size. */
+#define SPINOR_REG_CYPRESS_CFR3N_UNISECT	BIT(3) /* Uniform sector mode */
+#define SPINOR_REG_CYPRESS_CFR4V		0x00800005
+#define SPINOR_REG_CYPRESS_CFR5V		0x00800006
+#define SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_EN	0x3
+#define SPINOR_OP_CYPRESS_RD_FAST		0xee
+
 /* Supported SPI protocols */
 #define SNOR_PROTO_INST_MASK	GENMASK(23, 16)
 #define SNOR_PROTO_INST_SHIFT	16
-- 
2.25.0

  parent reply	other threads:[~2020-02-11 13:33 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-02-11 13:33 [PATCH 0/9] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
2020-02-11 13:33 ` [PATCH 2/9] spi: spi-mem: allow specifying a command's extension Pratyush Yadav
2020-02-11 13:33 ` [PATCH 3/9] spi: cadence-quadspi: Add support for octal DTR flashes Pratyush Yadav
     [not found] ` <20200211133348.15558-1-p.yadav-l0cyMroinI0@public.gmane.org>
2020-02-11 13:33   ` [PATCH 1/9] spi: spi-mem: allow specifying whether an op is DTR or not Pratyush Yadav
2020-02-11 13:33   ` [PATCH 4/9] mtd: spi-nor: add support for DTR protocol Pratyush Yadav
2020-02-11 13:33   ` [PATCH 5/9] mtd: spi-nor: get command opcode extension type from BFPT Pratyush Yadav
2020-02-11 13:33   ` [PATCH 6/9] mtd: spi-nor: parse xSPI Profile 1.0 table Pratyush Yadav
2020-02-11 13:33   ` [PATCH 7/9] mtd: spi-nor: use dummy cycle and address width info from SFDP Pratyush Yadav
2020-02-11 13:33 ` [PATCH 8/9] mtd: spi-nor: enable octal DTR mode when possible Pratyush Yadav
2020-02-11 13:33 ` Pratyush Yadav [this message]
     [not found]   ` <20200211133348.15558-10-p.yadav-l0cyMroinI0@public.gmane.org>
2020-02-13 10:36     ` [EXT] [PATCH 9/9] mtd: spi-nor: add support for Cypress Semper flash Kuldeep Singh

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200211133348.15558-10-p.yadav@ti.com \
    --to=p.yadav@ti.com \
    --cc=broonie@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=miquel.raynal@bootlin.com \
    --cc=nsekhar@ti.com \
    --cc=richard@nod.at \
    --cc=tudor.ambarus@microchip.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).