[PATCH 0/9] spi: meson-spicc: add support for AXG and G12A variants

[PATCH 0/9] spi: meson-spicc: add support for AXG and G12A variants

[Neil Armstrong]

The SPICC controller in Amlogic AXG & G12A is capable of driving the
CLK/MOSI/SS signal lines through the idle state which avoid the signals
floating in unexpected state, is capable of using linear clock divider
to reach a much fine tuned range of clocks, while the old controller only
uses a power of two clock divider, result at a more coarse clock range and
finally is capable of running at 80M clock.

The SPICC controller in Amlogic G12A takes the source clock from a specific
clock instead of the bus clock and has a different FIFO size and doesn't
handle the RX Half interrupt the same way as GXL & AXG variants. Thus
the burst management is simplified and takes in account a variable FIFO
size.

Now the controller can support frequencies higher than 30MHz, we need
the setup the I/O line delays in regard of the SPI clock frequency.

Neil Armstrong (7):
  spi: meson-spicc: remove unused variables
  spi: meson-spicc: support max 80MHz clock
  spi: meson-spicc: add min sclk for each compatible
  spi: meson-spicc: setup IO line delay
  spi: meson-spicc: adapt burst handling for G12A support
  dt-bindings: spi: amlogic,meson-gx-spicc: add Amlogic G12A compatible
  spi: meson-spicc: add support for Amlogic G12A

Sunny Luo (2):
  spi: meson-spicc: enhance output enable feature
  spi: meson-spicc: add a linear clock divider support

 .../bindings/spi/amlogic,meson-gx-spicc.yaml  |  22 +
 drivers/spi/Kconfig                           |   1 +
 drivers/spi/spi-meson-spicc.c                 | 496 +++++++++++++-----
 3 files changed, 392 insertions(+), 127 deletions(-)

-- 
2.22.0

[PATCH 1/9] spi: meson-spicc: remove unused variables

[Neil Armstrong]

Remove unused variables from spicc data struct.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 7f5680fe2568..8425e5ae1273 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -130,9 +130,7 @@ struct meson_spicc_device {
 	u8				*rx_buf;
 	unsigned int			bytes_per_word;
 	unsigned long			tx_remain;
-	unsigned long			txb_remain;
 	unsigned long			rx_remain;
-	unsigned long			rxb_remain;
 	unsigned long			xfer_remain;
 	bool				is_burst_end;
 	bool				is_last_burst;
-- 
2.22.0

[PATCH 2/9] spi: meson-spicc: enhance output enable feature

[Neil Armstrong]

From: Sunny Luo <sunny.luo@amlogic.com>

The SPICC controller in Meson-AXG is capable of driving the CLK/MOSI/SS
signal lines through the idle state (between two transmission operation),
which avoid the signals floating in unexpected state.

Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 drivers/spi/spi-meson-spicc.c | 53 +++++++++++++++++++++++++++++++++--
 1 file changed, 51 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 8425e5ae1273..ba70ef94a82a 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -9,11 +9,13 @@
 
 #include <linux/bitfield.h>
 #include <linux/clk.h>
+#include <linux/clk-provider.h>
 #include <linux/device.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
 #include <linux/types.h>
@@ -113,12 +115,23 @@
 
 #define SPICC_DWADDR	0x24	/* Write Address of DMA */
 
+#define SPICC_ENH_CTL0	0x38	/* Enhanced Feature */
+#define SPICC_ENH_MOSI_OEN		BIT(25)
+#define SPICC_ENH_CLK_OEN		BIT(26)
+#define SPICC_ENH_CS_OEN		BIT(27)
+#define SPICC_ENH_CLK_CS_DELAY_EN	BIT(28)
+#define SPICC_ENH_MAIN_CLK_AO		BIT(29)
+
 #define writel_bits_relaxed(mask, val, addr) \
 	writel_relaxed((readl_relaxed(addr) & ~(mask)) | (val), addr)
 
 #define SPICC_BURST_MAX	16
 #define SPICC_FIFO_HALF 10
 
+struct meson_spicc_data {
+	bool				has_oen;
+};
+
 struct meson_spicc_device {
 	struct spi_master		*master;
 	struct platform_device		*pdev;
@@ -126,6 +139,7 @@ struct meson_spicc_device {
 	struct clk			*core;
 	struct spi_message		*message;
 	struct spi_transfer		*xfer;
+	const struct meson_spicc_data	*data;
 	u8				*tx_buf;
 	u8				*rx_buf;
 	unsigned int			bytes_per_word;
@@ -136,6 +150,19 @@ struct meson_spicc_device {
 	bool				is_last_burst;
 };
 
+static void meson_spicc_oen_enable(struct meson_spicc_device *spicc)
+{
+	u32 conf;
+
+	if (!spicc->data->has_oen)
+		return;
+
+	conf = readl_relaxed(spicc->base + SPICC_ENH_CTL0) |
+		SPICC_ENH_MOSI_OEN | SPICC_ENH_CLK_OEN | SPICC_ENH_CS_OEN;
+
+	writel_relaxed(conf, spicc->base + SPICC_ENH_CTL0);
+}
+
 static inline bool meson_spicc_txfull(struct meson_spicc_device *spicc)
 {
 	return !!FIELD_GET(SPICC_TF,
@@ -489,6 +516,13 @@ static int meson_spicc_probe(struct platform_device *pdev)
 	spicc = spi_master_get_devdata(master);
 	spicc->master = master;
 
+	spicc->data = of_device_get_match_data(&pdev->dev);
+	if (!spicc->data) {
+		dev_err(&pdev->dev, "failed to get match data\n");
+		ret = -EINVAL;
+		goto out_master;
+	}
+
 	spicc->pdev = pdev;
 	platform_set_drvdata(pdev, spicc);
 
@@ -548,6 +582,8 @@ static int meson_spicc_probe(struct platform_device *pdev)
 	else
 		master->max_speed_hz = rate >> 2;
 
+	meson_spicc_oen_enable(spicc);
+
 	ret = devm_spi_register_master(&pdev->dev, master);
 	if (ret) {
 		dev_err(&pdev->dev, "spi master registration failed\n");
@@ -577,9 +613,22 @@ static int meson_spicc_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct meson_spicc_data meson_spicc_gx_data = {
+};
+
+static const struct meson_spicc_data meson_spicc_axg_data = {
+	.has_oen		= true,
+};
+
 static const struct of_device_id meson_spicc_of_match[] = {
-	{ .compatible = "amlogic,meson-gx-spicc", },
-	{ .compatible = "amlogic,meson-axg-spicc", },
+	{
+		.compatible	= "amlogic,meson-gx-spicc",
+		.data		= &meson_spicc_gx_data,
+	},
+	{
+		.compatible = "amlogic,meson-axg-spicc",
+		.data		= &meson_spicc_axg_data,
+	},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, meson_spicc_of_match);
-- 
2.22.0

[PATCH 3/9] spi: meson-spicc: add a linear clock divider support

[Neil Armstrong]

From: Sunny Luo <sunny.luo-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>

The SPICC controller in Meson-AXG SoC is capable of using
a linear clock divider to reach a much fine tuned range of clocks,
while the old controller only use a power of two clock divider,
result at a more coarse clock range.

Also convert the clock registration into Common Clock Framework.

Signed-off-by: Sunny Luo <sunny.luo-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
---
 drivers/spi/Kconfig           |   1 +
 drivers/spi/spi-meson-spicc.c | 204 +++++++++++++++++++++++++++-------
 2 files changed, 165 insertions(+), 40 deletions(-)

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index d6ed0c355954..7f86e591fba3 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -415,6 +415,7 @@ config SPI_FSL_ESPI
 
 config SPI_MESON_SPICC
 	tristate "Amlogic Meson SPICC controller"
+	depends on COMMON_CLK
 	depends on ARCH_MESON || COMPILE_TEST
 	help
 	  This enables master mode support for the SPICC (SPI communication
diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index ba70ef94a82a..bd434d9055d9 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -116,6 +116,9 @@
 #define SPICC_DWADDR	0x24	/* Write Address of DMA */
 
 #define SPICC_ENH_CTL0	0x38	/* Enhanced Feature */
+#define SPICC_ENH_CLK_CS_DELAY_MASK	GENMASK(15, 0)
+#define SPICC_ENH_DATARATE_MASK		GENMASK(23, 16)
+#define SPICC_ENH_DATARATE_EN		BIT(24)
 #define SPICC_ENH_MOSI_OEN		BIT(25)
 #define SPICC_ENH_CLK_OEN		BIT(26)
 #define SPICC_ENH_CS_OEN		BIT(27)
@@ -130,6 +133,7 @@
 
 struct meson_spicc_data {
 	bool				has_oen;
+	bool				has_enhance_clk_div;
 };
 
 struct meson_spicc_device {
@@ -137,6 +141,7 @@ struct meson_spicc_device {
 	struct platform_device		*pdev;
 	void __iomem			*base;
 	struct clk			*core;
+	struct clk			*clk;
 	struct spi_message		*message;
 	struct spi_transfer		*xfer;
 	const struct meson_spicc_data	*data;
@@ -322,40 +327,6 @@ static irqreturn_t meson_spicc_irq(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
-static u32 meson_spicc_setup_speed(struct meson_spicc_device *spicc, u32 conf,
-				   u32 speed)
-{
-	unsigned long parent, value;
-	unsigned int i, div;
-
-	parent = clk_get_rate(spicc->core);
-
-	/* Find closest inferior/equal possible speed */
-	for (i = 0 ; i < 7 ; ++i) {
-		/* 2^(data_rate+2) */
-		value = parent >> (i + 2);
-
-		if (value <= speed)
-			break;
-	}
-
-	/* If provided speed it lower than max divider, use max divider */
-	if (i > 7) {
-		div = 7;
-		dev_warn_once(&spicc->pdev->dev, "unable to get close to speed %u\n",
-			      speed);
-	} else
-		div = i;
-
-	dev_dbg(&spicc->pdev->dev, "parent %lu, speed %u -> %lu (%u)\n",
-		parent, speed, value, div);
-
-	conf &= ~SPICC_DATARATE_MASK;
-	conf |= FIELD_PREP(SPICC_DATARATE_MASK, div);
-
-	return conf;
-}
-
 static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 				   struct spi_transfer *xfer)
 {
@@ -364,9 +335,6 @@ static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 	/* Read original configuration */
 	conf = conf_orig = readl_relaxed(spicc->base + SPICC_CONREG);
 
-	/* Select closest divider */
-	conf = meson_spicc_setup_speed(spicc, conf, xfer->speed_hz);
-
 	/* Setup word width */
 	conf &= ~SPICC_BITLENGTH_MASK;
 	conf |= FIELD_PREP(SPICC_BITLENGTH_MASK,
@@ -375,6 +343,8 @@ static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 	/* Ignore if unchanged */
 	if (conf != conf_orig)
 		writel_relaxed(conf, spicc->base + SPICC_CONREG);
+
+	clk_set_rate(spicc->clk, xfer->speed_hz);
 }
 
 static int meson_spicc_transfer_one(struct spi_master *master,
@@ -481,9 +451,6 @@ static int meson_spicc_unprepare_transfer(struct spi_master *master)
 	/* Disable all IRQs */
 	writel(0, spicc->base + SPICC_INTREG);
 
-	/* Disable controller */
-	writel_bits_relaxed(SPICC_ENABLE, 0, spicc->base + SPICC_CONREG);
-
 	device_reset_optional(&spicc->pdev->dev);
 
 	return 0;
@@ -502,6 +469,152 @@ static void meson_spicc_cleanup(struct spi_device *spi)
 	spi->controller_state = NULL;
 }
 
+/*
+ * The Clock Mux
+ *            x-----------------x   x------------x    x------\
+ *        |---| pow2 fixed div  |---| pow2 div   |----|      |
+ *        |   x-----------------x   x------------x    |      |
+ * src ---|                                           | mux  |-- out
+ *        |   x-----------------x   x------------x    |      |
+ *        |---| enh fixed div   |---| enh div    |0---|      |
+ *            x-----------------x   x------------x    x------/
+ *
+ * Clk path for GX series:
+ *    src -> pow2 fixed div -> pow2 div -> out
+ *
+ * Clk path for AXG series:
+ *    src -> pow2 fixed div -> pow2 div -> mux -> out
+ *    src -> enh fixed div -> enh div -> mux -> out
+ */
+
+static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
+{
+	struct device *dev = &spicc->pdev->dev;
+	struct clk_fixed_factor *pow2_fixed_div, *enh_fixed_div;
+	struct clk_divider *pow2_div, *enh_div;
+	struct clk_mux *mux;
+	struct clk_init_data init;
+	struct clk *clk;
+	struct clk_parent_data parent_data[2];
+	char name[64];
+
+	memset(&init, 0, sizeof(init));
+	memset(&parent_data, 0, sizeof(parent_data));
+
+	init.parent_data = parent_data;
+
+	/* algorithm for pow2 div: rate = freq / 4 / (2 ^ N) */
+
+	pow2_fixed_div = devm_kzalloc(dev, sizeof(*pow2_fixed_div), GFP_KERNEL);
+	if (!pow2_fixed_div)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#pow2_fixed_div", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_fixed_factor_ops;
+	init.flags = 0;
+	parent_data[0].hw = __clk_get_hw(spicc->core);
+	init.num_parents = 1;
+
+	pow2_fixed_div->mult = 1,
+	pow2_fixed_div->div = 4,
+	pow2_fixed_div->hw.init = &init;
+
+	clk = devm_clk_register(dev, &pow2_fixed_div->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	pow2_div = devm_kzalloc(dev, sizeof(*pow2_div), GFP_KERNEL);
+	if (!pow2_div)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#pow2_div", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_divider_ops;
+	init.flags = CLK_SET_RATE_PARENT;
+	parent_data[0].hw = &pow2_fixed_div->hw;
+	init.num_parents = 1;
+
+	pow2_div->shift = 16,
+	pow2_div->width = 3,
+	pow2_div->flags = CLK_DIVIDER_POWER_OF_TWO,
+	pow2_div->reg = spicc->base + SPICC_CONREG;
+	pow2_div->hw.init = &init;
+
+	clk = devm_clk_register(dev, &pow2_div->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	if (!spicc->data->has_enhance_clk_div) {
+		spicc->clk = clk;
+		return 0;
+	}
+
+	/* algorithm for enh div: rate = freq / 2 / (N + 1) */
+
+	enh_fixed_div = devm_kzalloc(dev, sizeof(*enh_fixed_div), GFP_KERNEL);
+	if (!enh_fixed_div)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#enh_fixed_div", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_fixed_factor_ops;
+	init.flags = 0;
+	parent_data[0].hw = __clk_get_hw(spicc->core);
+	init.num_parents = 1;
+
+	enh_fixed_div->mult = 1,
+	enh_fixed_div->div = 2,
+	enh_fixed_div->hw.init = &init;
+
+	clk = devm_clk_register(dev, &enh_fixed_div->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	enh_div = devm_kzalloc(dev, sizeof(*enh_div), GFP_KERNEL);
+	if (!enh_div)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#enh_div", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_divider_ops;
+	init.flags = CLK_SET_RATE_PARENT;
+	parent_data[0].hw = &enh_fixed_div->hw;
+	init.num_parents = 1;
+
+	enh_div->shift	= 16,
+	enh_div->width	= 8,
+	enh_div->reg = spicc->base + SPICC_ENH_CTL0;
+	enh_div->hw.init = &init;
+
+	clk = devm_clk_register(dev, &enh_div->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
+	if (!mux)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#sel", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_mux_ops;
+	parent_data[0].hw = &pow2_div->hw;
+	parent_data[1].hw = &enh_div->hw;
+	init.num_parents = 2;
+	init.flags = CLK_SET_RATE_PARENT;
+
+	mux->mask = 0x1,
+	mux->shift = 24,
+	mux->reg = spicc->base + SPICC_ENH_CTL0;
+	mux->hw.init = &init;
+
+	spicc->clk = devm_clk_register(dev, &mux->hw);
+	if (WARN_ON(IS_ERR(spicc->clk)))
+		return PTR_ERR(spicc->clk);
+
+	return 0;
+}
+
 static int meson_spicc_probe(struct platform_device *pdev)
 {
 	struct spi_master *master;
@@ -533,6 +646,10 @@ static int meson_spicc_probe(struct platform_device *pdev)
 		goto out_master;
 	}
 
+	/* Set master mode and enable controller */
+	writel_relaxed(SPICC_ENABLE | SPICC_MODE_MASTER,
+		       spicc->base + SPICC_CONREG);
+
 	/* Disable all IRQs */
 	writel_relaxed(0, spicc->base + SPICC_INTREG);
 
@@ -584,6 +701,12 @@ static int meson_spicc_probe(struct platform_device *pdev)
 
 	meson_spicc_oen_enable(spicc);
 
+	ret = meson_spicc_clk_init(spicc);
+	if (ret) {
+		dev_err(&pdev->dev, "clock registration failed\n");
+		goto out_master;
+	}
+
 	ret = devm_spi_register_master(&pdev->dev, master);
 	if (ret) {
 		dev_err(&pdev->dev, "spi master registration failed\n");
@@ -618,6 +741,7 @@ static const struct meson_spicc_data meson_spicc_gx_data = {
 
 static const struct meson_spicc_data meson_spicc_axg_data = {
 	.has_oen		= true,
+	.has_enhance_clk_div	= true,
 };
 
 static const struct of_device_id meson_spicc_of_match[] = {
-- 
2.22.0

[PATCH 4/9] spi: meson-spicc: support max 80MHz clock

[Neil Armstrong]

The SPICC controller in Meson-AXG is capable of running at 80M clock.
The ASIC IP is improved and the clock is actually running higher than
previous old SoCs.

Signed-off-by: Sunny Luo <sunny.luo-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index bd434d9055d9..710b4e780daa 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -35,7 +35,6 @@
  *   to have a CS go down over the full transfer
  */
 
-#define SPICC_MAX_FREQ	30000000
 #define SPICC_MAX_BURST	128
 
 /* Register Map */
@@ -132,6 +131,7 @@
 #define SPICC_FIFO_HALF 10
 
 struct meson_spicc_data {
+	unsigned int			max_speed_hz;
 	bool				has_oen;
 	bool				has_enhance_clk_div;
 };
@@ -693,11 +693,9 @@ static int meson_spicc_probe(struct platform_device *pdev)
 	master->transfer_one = meson_spicc_transfer_one;
 	master->use_gpio_descriptors = true;
 
-	/* Setup max rate according to the Meson GX datasheet */
-	if ((rate >> 2) > SPICC_MAX_FREQ)
-		master->max_speed_hz = SPICC_MAX_FREQ;
-	else
-		master->max_speed_hz = rate >> 2;
+	/* Setup max rate according to the Meson datasheet */
+	master->max_speed_hz = min_t(unsigned int, rate >> 1,
+				     spicc->data->max_speed_hz);
 
 	meson_spicc_oen_enable(spicc);
 
@@ -737,9 +735,11 @@ static int meson_spicc_remove(struct platform_device *pdev)
 }
 
 static const struct meson_spicc_data meson_spicc_gx_data = {
+	.max_speed_hz		= 30000000,
 };
 
 static const struct meson_spicc_data meson_spicc_axg_data = {
+	.max_speed_hz		= 80000000,
 	.has_oen		= true,
 	.has_enhance_clk_div	= true,
 };
-- 
2.22.0

[PATCH 5/9] spi: meson-spicc: add min sclk for each compatible

[Neil Armstrong]

The G12A SPICC controller variant takes the source clock from a specific
clock instead of the bus clock.
The minimal clock calculus won't work with the G12A support, thus add the
minimal supported clock for each variant and pass this to the SPI core.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 710b4e780daa..b5bd3a897e8f 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -132,6 +132,7 @@
 
 struct meson_spicc_data {
 	unsigned int			max_speed_hz;
+	unsigned int			min_speed_hz;
 	bool				has_oen;
 	bool				has_enhance_clk_div;
 };
@@ -685,7 +686,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 				     SPI_BPW_MASK(16) |
 				     SPI_BPW_MASK(8);
 	master->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX);
-	master->min_speed_hz = rate >> 9;
+	master->min_speed_hz = spicc->data->min_speed_hz;
 	master->setup = meson_spicc_setup;
 	master->cleanup = meson_spicc_cleanup;
 	master->prepare_message = meson_spicc_prepare_message;
@@ -736,10 +737,12 @@ static int meson_spicc_remove(struct platform_device *pdev)
 
 static const struct meson_spicc_data meson_spicc_gx_data = {
 	.max_speed_hz		= 30000000,
+	.min_speed_hz		= 325000,
 };
 
 static const struct meson_spicc_data meson_spicc_axg_data = {
 	.max_speed_hz		= 80000000,
+	.min_speed_hz		= 325000,
 	.has_oen		= true,
 	.has_enhance_clk_div	= true,
 };
-- 
2.22.0

[PATCH 6/9] spi: meson-spicc: setup IO line delay

[Neil Armstrong]

Now the controller can support frequencies higher than 30MHz, we need
the setup the I/O line delays in regard of the SPI clock frequency.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 drivers/spi/spi-meson-spicc.c | 61 ++++++++++++++++++++++++++++++++++-
 1 file changed, 60 insertions(+), 1 deletion(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index b5bd3a897e8f..4494a791f4a7 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -106,7 +106,21 @@
 #define SPICC_SWAP_RO		BIT(14) /* RX FIFO Data Swap Read-Only */
 #define SPICC_SWAP_W1		BIT(15) /* RX FIFO Data Swap Write-Only */
 #define SPICC_DLYCTL_RO_MASK	GENMASK(20, 15) /* Delay Control Read-Only */
-#define SPICC_DLYCTL_W1_MASK	GENMASK(21, 16) /* Delay Control Write-Only */
+#define SPICC_MO_DELAY_MASK	GENMASK(17, 16) /* Master Output Delay */
+#define SPICC_MO_NO_DELAY	0
+#define SPICC_MO_DELAY_1_CYCLE	1
+#define SPICC_MO_DELAY_2_CYCLE	2
+#define SPICC_MO_DELAY_3_CYCLE	3
+#define SPICC_MI_DELAY_MASK	GENMASK(19, 18) /* Master Input Delay */
+#define SPICC_MI_NO_DELAY	0
+#define SPICC_MI_DELAY_1_CYCLE	1
+#define SPICC_MI_DELAY_2_CYCLE	2
+#define SPICC_MI_DELAY_3_CYCLE	3
+#define SPICC_MI_CAP_DELAY_MASK	GENMASK(21, 20) /* Master Capture Delay */
+#define SPICC_CAP_AHEAD_2_CYCLE	0
+#define SPICC_CAP_AHEAD_1_CYCLE	1
+#define SPICC_CAP_NO_DELAY	2
+#define SPICC_CAP_DELAY_1_CYCLE	3
 #define SPICC_FIFORST_RO_MASK	GENMASK(22, 21) /* FIFO Softreset Read-Only */
 #define SPICC_FIFORST_W1_MASK	GENMASK(23, 22) /* FIFO Softreset Write-Only */
 
@@ -328,6 +342,49 @@ static irqreturn_t meson_spicc_irq(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
+static void meson_spicc_auto_io_delay(struct meson_spicc_device *spicc)
+{
+	u32 div, hz;
+	u32 mi_delay, cap_delay;
+	u32 conf;
+
+	if (spicc->data->has_enhance_clk_div) {
+		div = FIELD_GET(SPICC_ENH_DATARATE_MASK,
+				readl_relaxed(spicc->base + SPICC_ENH_CTL0));
+		div++;
+		div <<= 1;
+	} else {
+		div = FIELD_GET(SPICC_DATARATE_MASK,
+				readl_relaxed(spicc->base + SPICC_CONREG));
+		div += 2;
+		div = 1 << div;
+	}
+
+	mi_delay = SPICC_MI_NO_DELAY;
+	cap_delay = SPICC_CAP_AHEAD_2_CYCLE;
+	hz = clk_get_rate(spicc->clk);
+
+	if (hz >= 100000000)
+		cap_delay = SPICC_CAP_DELAY_1_CYCLE;
+	else if (hz >= 80000000)
+		cap_delay = SPICC_CAP_NO_DELAY;
+	else if (hz >= 40000000)
+		cap_delay = SPICC_CAP_AHEAD_1_CYCLE;
+	else if (div >= 16)
+		mi_delay = SPICC_MI_DELAY_3_CYCLE;
+	else if (div >= 8)
+		mi_delay = SPICC_MI_DELAY_2_CYCLE;
+	else if (div >= 6)
+		mi_delay = SPICC_MI_DELAY_1_CYCLE;
+
+	conf = readl_relaxed(spicc->base + SPICC_TESTREG);
+	conf &= ~(SPICC_MO_DELAY_MASK | SPICC_MI_DELAY_MASK
+		  | SPICC_MI_CAP_DELAY_MASK);
+	conf |= FIELD_PREP(SPICC_MI_DELAY_MASK, mi_delay);
+	conf |= FIELD_PREP(SPICC_MI_CAP_DELAY_MASK, cap_delay);
+	writel_relaxed(conf, spicc->base + SPICC_TESTREG);
+}
+
 static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 				   struct spi_transfer *xfer)
 {
@@ -346,6 +403,8 @@ static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 		writel_relaxed(conf, spicc->base + SPICC_CONREG);
 
 	clk_set_rate(spicc->clk, xfer->speed_hz);
+
+	meson_spicc_auto_io_delay(spicc);
 }
 
 static int meson_spicc_transfer_one(struct spi_master *master,
-- 
2.22.0

[PATCH 7/9] spi: meson-spicc: adapt burst handling for G12A support

[Neil Armstrong]

The G12A SPICC controller variant has a different FIFO size and doesn't
handle the RX Half interrupt the same way as GXL & AXG variants.

Thus simplify the burst management and take in account a variable FIFO
size.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 drivers/spi/spi-meson-spicc.c | 129 +++++++++++++---------------------
 1 file changed, 50 insertions(+), 79 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 4494a791f4a7..351ccd8dd2c2 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -141,12 +141,10 @@
 #define writel_bits_relaxed(mask, val, addr) \
 	writel_relaxed((readl_relaxed(addr) & ~(mask)) | (val), addr)
 
-#define SPICC_BURST_MAX	16
-#define SPICC_FIFO_HALF 10
-
 struct meson_spicc_data {
 	unsigned int			max_speed_hz;
 	unsigned int			min_speed_hz;
+	unsigned int			fifo_size;
 	bool				has_oen;
 	bool				has_enhance_clk_div;
 };
@@ -166,8 +164,6 @@ struct meson_spicc_device {
 	unsigned long			tx_remain;
 	unsigned long			rx_remain;
 	unsigned long			xfer_remain;
-	bool				is_burst_end;
-	bool				is_last_burst;
 };
 
 static void meson_spicc_oen_enable(struct meson_spicc_device *spicc)
@@ -191,7 +187,7 @@ static inline bool meson_spicc_txfull(struct meson_spicc_device *spicc)
 
 static inline bool meson_spicc_rxready(struct meson_spicc_device *spicc)
 {
-	return FIELD_GET(SPICC_RH | SPICC_RR | SPICC_RF_EN,
+	return FIELD_GET(SPICC_RH | SPICC_RR | SPICC_RF,
 			 readl_relaxed(spicc->base + SPICC_STATREG));
 }
 
@@ -246,34 +242,22 @@ static inline void meson_spicc_tx(struct meson_spicc_device *spicc)
 			       spicc->base + SPICC_TXDATA);
 }
 
-static inline u32 meson_spicc_setup_rx_irq(struct meson_spicc_device *spicc,
-					   u32 irq_ctrl)
+static inline void meson_spicc_setup_burst(struct meson_spicc_device *spicc)
 {
-	if (spicc->rx_remain > SPICC_FIFO_HALF)
-		irq_ctrl |= SPICC_RH_EN;
-	else
-		irq_ctrl |= SPICC_RR_EN;
-
-	return irq_ctrl;
-}
 
-static inline void meson_spicc_setup_burst(struct meson_spicc_device *spicc,
-					   unsigned int burst_len)
-{
+	unsigned int burst_len = min_t(unsigned int,
+				       spicc->xfer_remain /
+				       spicc->bytes_per_word,
+				       spicc->data->fifo_size);
 	/* Setup Xfer variables */
 	spicc->tx_remain = burst_len;
 	spicc->rx_remain = burst_len;
 	spicc->xfer_remain -= burst_len * spicc->bytes_per_word;
-	spicc->is_burst_end = false;
-	if (burst_len < SPICC_BURST_MAX || !spicc->xfer_remain)
-		spicc->is_last_burst = true;
-	else
-		spicc->is_last_burst = false;
 
 	/* Setup burst length */
 	writel_bits_relaxed(SPICC_BURSTLENGTH_MASK,
 			FIELD_PREP(SPICC_BURSTLENGTH_MASK,
-				burst_len),
+				burst_len - 1),
 			spicc->base + SPICC_CONREG);
 
 	/* Fill TX FIFO */
@@ -283,61 +267,26 @@ static inline void meson_spicc_setup_burst(struct meson_spicc_device *spicc,
 static irqreturn_t meson_spicc_irq(int irq, void *data)
 {
 	struct meson_spicc_device *spicc = (void *) data;
-	u32 ctrl = readl_relaxed(spicc->base + SPICC_INTREG);
-	u32 stat = readl_relaxed(spicc->base + SPICC_STATREG) & ctrl;
 
-	ctrl &= ~(SPICC_RH_EN | SPICC_RR_EN);
+	writel_bits_relaxed(SPICC_TC, SPICC_TC, spicc->base + SPICC_STATREG);
 
 	/* Empty RX FIFO */
 	meson_spicc_rx(spicc);
 
-	/* Enable TC interrupt since we transferred everything */
-	if (!spicc->tx_remain && !spicc->rx_remain) {
-		spicc->is_burst_end = true;
-
-		/* Enable TC interrupt */
-		ctrl |= SPICC_TC_EN;
-
-		/* Reload IRQ status */
-		stat = readl_relaxed(spicc->base + SPICC_STATREG) & ctrl;
-	}
-
-	/* Check transfer complete */
-	if ((stat & SPICC_TC) && spicc->is_burst_end) {
-		unsigned int burst_len;
-
-		/* Clear TC bit */
-		writel_relaxed(SPICC_TC, spicc->base + SPICC_STATREG);
-
-		/* Disable TC interrupt */
-		ctrl &= ~SPICC_TC_EN;
-
-		if (spicc->is_last_burst) {
-			/* Disable all IRQs */
-			writel(0, spicc->base + SPICC_INTREG);
-
-			spi_finalize_current_transfer(spicc->master);
+	if (!spicc->xfer_remain) {
+		/* Disable all IRQs */
+		writel(0, spicc->base + SPICC_INTREG);
 
-			return IRQ_HANDLED;
-		}
+		spi_finalize_current_transfer(spicc->master);
 
-		burst_len = min_t(unsigned int,
-				  spicc->xfer_remain / spicc->bytes_per_word,
-				  SPICC_BURST_MAX);
-
-		/* Setup burst */
-		meson_spicc_setup_burst(spicc, burst_len);
-
-		/* Restart burst */
-		writel_bits_relaxed(SPICC_XCH, SPICC_XCH,
-				    spicc->base + SPICC_CONREG);
+		return IRQ_HANDLED;
 	}
 
-	/* Setup RX interrupt trigger */
-	ctrl = meson_spicc_setup_rx_irq(spicc, ctrl);
+	/* Setup burst */
+	meson_spicc_setup_burst(spicc);
 
-	/* Reconfigure interrupts */
-	writel(ctrl, spicc->base + SPICC_INTREG);
+	/* Start burst */
+	writel_bits_relaxed(SPICC_XCH, SPICC_XCH, spicc->base + SPICC_CONREG);
 
 	return IRQ_HANDLED;
 }
@@ -405,6 +354,28 @@ static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 	clk_set_rate(spicc->clk, xfer->speed_hz);
 
 	meson_spicc_auto_io_delay(spicc);
+
+	writel_relaxed(0, spicc->base + SPICC_DMAREG);
+}
+
+static void meson_spicc_reset_fifo(struct meson_spicc_device *spicc)
+{
+	u32 data;
+
+	if (spicc->data->has_oen)
+		writel_bits_relaxed(SPICC_ENH_MAIN_CLK_AO,
+				    SPICC_ENH_MAIN_CLK_AO,
+				    spicc->base + SPICC_ENH_CTL0);
+
+	writel_bits_relaxed(SPICC_FIFORST_W1_MASK, SPICC_FIFORST_W1_MASK,
+			    spicc->base + SPICC_TESTREG);
+
+	while (meson_spicc_rxready(spicc))
+		data = readl_relaxed(spicc->base + SPICC_RXDATA);
+
+	if (spicc->data->has_oen)
+		writel_bits_relaxed(SPICC_ENH_MAIN_CLK_AO, 0,
+				    spicc->base + SPICC_ENH_CTL0);
 }
 
 static int meson_spicc_transfer_one(struct spi_master *master,
@@ -412,8 +383,6 @@ static int meson_spicc_transfer_one(struct spi_master *master,
 				    struct spi_transfer *xfer)
 {
 	struct meson_spicc_device *spicc = spi_master_get_devdata(master);
-	unsigned int burst_len;
-	u32 irq = 0;
 
 	/* Store current transfer */
 	spicc->xfer = xfer;
@@ -427,22 +396,22 @@ static int meson_spicc_transfer_one(struct spi_master *master,
 	spicc->bytes_per_word =
 	   DIV_ROUND_UP(spicc->xfer->bits_per_word, 8);
 
+	if (xfer->len % spicc->bytes_per_word)
+		return -EINVAL;
+
 	/* Setup transfer parameters */
 	meson_spicc_setup_xfer(spicc, xfer);
 
-	burst_len = min_t(unsigned int,
-			  spicc->xfer_remain / spicc->bytes_per_word,
-			  SPICC_BURST_MAX);
-
-	meson_spicc_setup_burst(spicc, burst_len);
+	meson_spicc_reset_fifo(spicc);
 
-	irq = meson_spicc_setup_rx_irq(spicc, irq);
+	/* Setup burst */
+	meson_spicc_setup_burst(spicc);
 
 	/* Start burst */
 	writel_bits_relaxed(SPICC_XCH, SPICC_XCH, spicc->base + SPICC_CONREG);
 
 	/* Enable interrupts */
-	writel_relaxed(irq, spicc->base + SPICC_INTREG);
+	writel_relaxed(SPICC_TC_EN, spicc->base + SPICC_INTREG);
 
 	return 1;
 }
@@ -499,7 +468,7 @@ static int meson_spicc_prepare_message(struct spi_master *master,
 	/* Setup no wait cycles by default */
 	writel_relaxed(0, spicc->base + SPICC_PERIODREG);
 
-	writel_bits_relaxed(BIT(24), BIT(24), spicc->base + SPICC_TESTREG);
+	writel_bits_relaxed(SPICC_LBC_W1, 0, spicc->base + SPICC_TESTREG);
 
 	return 0;
 }
@@ -797,11 +766,13 @@ static int meson_spicc_remove(struct platform_device *pdev)
 static const struct meson_spicc_data meson_spicc_gx_data = {
 	.max_speed_hz		= 30000000,
 	.min_speed_hz		= 325000,
+	.fifo_size		= 16,
 };
 
 static const struct meson_spicc_data meson_spicc_axg_data = {
 	.max_speed_hz		= 80000000,
 	.min_speed_hz		= 325000,
+	.fifo_size		= 16,
 	.has_oen		= true,
 	.has_enhance_clk_div	= true,
 };
-- 
2.22.0

[PATCH 8/9] dt-bindings: spi: amlogic,meson-gx-spicc: add Amlogic G12A compatible

[Neil Armstrong]

The Amlogic G12A SPICC controllers uses a secondary clock used to feed the
baud rate generator and the delay control logic.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 .../bindings/spi/amlogic,meson-gx-spicc.yaml  | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml b/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml
index 49b617c98ae7..9147df29022a 100644
--- a/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml
+++ b/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml
@@ -22,6 +22,7 @@ properties:
     enum:
       - amlogic,meson-gx-spicc # SPICC controller on Amlogic GX and compatible SoCs
       - amlogic,meson-axg-spicc # SPICC controller on Amlogic AXG and compatible SoCs
+      - amlogic,meson-g12a-spicc # SPICC controller on Amlogic G12A and compatible SoCs
 
   interrupts:
     maxItems: 1
@@ -40,6 +41,27 @@ properties:
     items:
       - const: core
 
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - amlogic,meson-g12a-spicc
+
+then:
+  properties:
+    clocks:
+      contains:
+        items:
+          - description: controller register bus clock
+          - description: baud rate generator and delay control clock
+
+    clock-names:
+      minItems: 2
+      items:
+        - const: core
+        - const: pclk
+
 required:
   - compatible
   - reg
-- 
2.22.0

[PATCH 9/9] spi: meson-spicc: add support for Amlogic G12A

[Neil Armstrong]

Add support for the SPICC controllers on the Amlogic G12A SoCs family.

The G12A SPICC controllers inherit from the AXG enhanced registers but
takes an external pclk for the baud rate generator and can achieve up to
166MHz SCLK.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 54 +++++++++++++++++++++++++++++------
 1 file changed, 46 insertions(+), 8 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 351ccd8dd2c2..77f7d0e0e46a 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -147,6 +147,7 @@ struct meson_spicc_data {
 	unsigned int			fifo_size;
 	bool				has_oen;
 	bool				has_enhance_clk_div;
+	bool				has_pclk;
 };
 
 struct meson_spicc_device {
@@ -154,6 +155,7 @@ struct meson_spicc_device {
 	struct platform_device		*pdev;
 	void __iomem			*base;
 	struct clk			*core;
+	struct clk			*pclk;
 	struct clk			*clk;
 	struct spi_message		*message;
 	struct spi_transfer		*xfer;
@@ -514,6 +516,10 @@ static void meson_spicc_cleanup(struct spi_device *spi)
  * Clk path for AXG series:
  *    src -> pow2 fixed div -> pow2 div -> mux -> out
  *    src -> enh fixed div -> enh div -> mux -> out
+ *
+ * Clk path for G12A series:
+ *    pclk -> pow2 fixed div -> pow2 div -> mux -> out
+ *    pclk -> enh fixed div -> enh div -> mux -> out
  */
 
 static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
@@ -542,7 +548,10 @@ static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
 	init.name = name;
 	init.ops = &clk_fixed_factor_ops;
 	init.flags = 0;
-	parent_data[0].hw = __clk_get_hw(spicc->core);
+	if (spicc->data->has_pclk)
+		parent_data[0].hw = __clk_get_hw(spicc->pclk);
+	else
+		parent_data[0].hw = __clk_get_hw(spicc->core);
 	init.num_parents = 1;
 
 	pow2_fixed_div->mult = 1,
@@ -589,7 +598,10 @@ static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
 	init.name = name;
 	init.ops = &clk_fixed_factor_ops;
 	init.flags = 0;
-	parent_data[0].hw = __clk_get_hw(spicc->core);
+	if (spicc->data->has_pclk)
+		parent_data[0].hw = __clk_get_hw(spicc->pclk);
+	else
+		parent_data[0].hw = __clk_get_hw(spicc->core);
 	init.num_parents = 1;
 
 	enh_fixed_div->mult = 1,
@@ -648,7 +660,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 {
 	struct spi_master *master;
 	struct meson_spicc_device *spicc;
-	int ret, irq, rate;
+	int ret, irq;
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*spicc));
 	if (!master) {
@@ -697,12 +709,26 @@ static int meson_spicc_probe(struct platform_device *pdev)
 		goto out_master;
 	}
 
+	if (spicc->data->has_pclk) {
+		spicc->pclk = devm_clk_get(&pdev->dev, "pclk");
+		if (IS_ERR(spicc->pclk)) {
+			dev_err(&pdev->dev, "pclk clock request failed\n");
+			ret = PTR_ERR(spicc->pclk);
+			goto out_master;
+		}
+	}
+
 	ret = clk_prepare_enable(spicc->core);
 	if (ret) {
 		dev_err(&pdev->dev, "core clock enable failed\n");
 		goto out_master;
 	}
-	rate = clk_get_rate(spicc->core);
+
+	ret = clk_prepare_enable(spicc->pclk);
+	if (ret) {
+		dev_err(&pdev->dev, "pclk clock enable failed\n");
+		goto out_master;
+	}
 
 	device_reset_optional(&pdev->dev);
 
@@ -715,6 +741,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 				     SPI_BPW_MASK(8);
 	master->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX);
 	master->min_speed_hz = spicc->data->min_speed_hz;
+	master->max_speed_hz = spicc->data->max_speed_hz;
 	master->setup = meson_spicc_setup;
 	master->cleanup = meson_spicc_cleanup;
 	master->prepare_message = meson_spicc_prepare_message;
@@ -722,10 +749,6 @@ static int meson_spicc_probe(struct platform_device *pdev)
 	master->transfer_one = meson_spicc_transfer_one;
 	master->use_gpio_descriptors = true;
 
-	/* Setup max rate according to the Meson datasheet */
-	master->max_speed_hz = min_t(unsigned int, rate >> 1,
-				     spicc->data->max_speed_hz);
-
 	meson_spicc_oen_enable(spicc);
 
 	ret = meson_spicc_clk_init(spicc);
@@ -744,6 +767,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 
 out_clk:
 	clk_disable_unprepare(spicc->core);
+	clk_disable_unprepare(spicc->pclk);
 
 out_master:
 	spi_master_put(master);
@@ -759,6 +783,7 @@ static int meson_spicc_remove(struct platform_device *pdev)
 	writel(0, spicc->base + SPICC_CONREG);
 
 	clk_disable_unprepare(spicc->core);
+	clk_disable_unprepare(spicc->pclk);
 
 	return 0;
 }
@@ -777,6 +802,15 @@ static const struct meson_spicc_data meson_spicc_axg_data = {
 	.has_enhance_clk_div	= true,
 };
 
+static const struct meson_spicc_data meson_spicc_g12a_data = {
+	.max_speed_hz		= 166666666,
+	.min_speed_hz		= 50000,
+	.fifo_size		= 15,
+	.has_oen		= true,
+	.has_enhance_clk_div	= true,
+	.has_pclk		= true,
+};
+
 static const struct of_device_id meson_spicc_of_match[] = {
 	{
 		.compatible	= "amlogic,meson-gx-spicc",
@@ -786,6 +820,10 @@ static const struct of_device_id meson_spicc_of_match[] = {
 		.compatible = "amlogic,meson-axg-spicc",
 		.data		= &meson_spicc_axg_data,
 	},
+	{
+		.compatible = "amlogic,meson-g12a-spicc",
+		.data		= &meson_spicc_g12a_data,
+	},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, meson_spicc_of_match);
-- 
2.22.0

Applied "spi: dt-bindings: amlogic, meson-gx-spicc: add Amlogic G12A compatible" to the spi tree

[Mark Brown]

The patch

   spi: dt-bindings: amlogic, meson-gx-spicc: add Amlogic G12A compatible

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 9ea7db818d9dcbbde581925b82bbe259e1926e20 Mon Sep 17 00:00:00 2001
From: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Date: Thu, 12 Mar 2020 14:31:30 +0100
Subject: [PATCH] spi: dt-bindings: amlogic, meson-gx-spicc: add Amlogic G12A
 compatible

The Amlogic G12A SPICC controllers uses a secondary clock used to feed the
baud rate generator and the delay control logic.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Link: https://lore.kernel.org/r/20200312133131.26430-9-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org
Signed-off-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 .../bindings/spi/amlogic,meson-gx-spicc.yaml  | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml b/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml
index 49b617c98ae7..9147df29022a 100644
--- a/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml
+++ b/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml
@@ -22,6 +22,7 @@ properties:
     enum:
       - amlogic,meson-gx-spicc # SPICC controller on Amlogic GX and compatible SoCs
       - amlogic,meson-axg-spicc # SPICC controller on Amlogic AXG and compatible SoCs
+      - amlogic,meson-g12a-spicc # SPICC controller on Amlogic G12A and compatible SoCs
 
   interrupts:
     maxItems: 1
@@ -40,6 +41,27 @@ properties:
     items:
       - const: core
 
+if:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - amlogic,meson-g12a-spicc
+
+then:
+  properties:
+    clocks:
+      contains:
+        items:
+          - description: controller register bus clock
+          - description: baud rate generator and delay control clock
+
+    clock-names:
+      minItems: 2
+      items:
+        - const: core
+        - const: pclk
+
 required:
   - compatible
   - reg
-- 
2.20.1

Applied "spi: meson-spicc: add support for Amlogic G12A" to the spi tree

[Mark Brown]

The patch

   spi: meson-spicc: add support for Amlogic G12A

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 4e3d322058a5e5afda100005a94ec7f0bf509d43 Mon Sep 17 00:00:00 2001
From: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Date: Thu, 12 Mar 2020 14:31:31 +0100
Subject: [PATCH] spi: meson-spicc: add support for Amlogic G12A

Add support for the SPICC controllers on the Amlogic G12A SoCs family.

The G12A SPICC controllers inherit from the AXG enhanced registers but
takes an external pclk for the baud rate generator and can achieve up to
166MHz SCLK.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Link: https://lore.kernel.org/r/20200312133131.26430-10-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org
Signed-off-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 54 +++++++++++++++++++++++++++++------
 1 file changed, 46 insertions(+), 8 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 351ccd8dd2c2..77f7d0e0e46a 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -147,6 +147,7 @@ struct meson_spicc_data {
 	unsigned int			fifo_size;
 	bool				has_oen;
 	bool				has_enhance_clk_div;
+	bool				has_pclk;
 };
 
 struct meson_spicc_device {
@@ -154,6 +155,7 @@ struct meson_spicc_device {
 	struct platform_device		*pdev;
 	void __iomem			*base;
 	struct clk			*core;
+	struct clk			*pclk;
 	struct clk			*clk;
 	struct spi_message		*message;
 	struct spi_transfer		*xfer;
@@ -514,6 +516,10 @@ static void meson_spicc_cleanup(struct spi_device *spi)
  * Clk path for AXG series:
  *    src -> pow2 fixed div -> pow2 div -> mux -> out
  *    src -> enh fixed div -> enh div -> mux -> out
+ *
+ * Clk path for G12A series:
+ *    pclk -> pow2 fixed div -> pow2 div -> mux -> out
+ *    pclk -> enh fixed div -> enh div -> mux -> out
  */
 
 static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
@@ -542,7 +548,10 @@ static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
 	init.name = name;
 	init.ops = &clk_fixed_factor_ops;
 	init.flags = 0;
-	parent_data[0].hw = __clk_get_hw(spicc->core);
+	if (spicc->data->has_pclk)
+		parent_data[0].hw = __clk_get_hw(spicc->pclk);
+	else
+		parent_data[0].hw = __clk_get_hw(spicc->core);
 	init.num_parents = 1;
 
 	pow2_fixed_div->mult = 1,
@@ -589,7 +598,10 @@ static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
 	init.name = name;
 	init.ops = &clk_fixed_factor_ops;
 	init.flags = 0;
-	parent_data[0].hw = __clk_get_hw(spicc->core);
+	if (spicc->data->has_pclk)
+		parent_data[0].hw = __clk_get_hw(spicc->pclk);
+	else
+		parent_data[0].hw = __clk_get_hw(spicc->core);
 	init.num_parents = 1;
 
 	enh_fixed_div->mult = 1,
@@ -648,7 +660,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 {
 	struct spi_master *master;
 	struct meson_spicc_device *spicc;
-	int ret, irq, rate;
+	int ret, irq;
 
 	master = spi_alloc_master(&pdev->dev, sizeof(*spicc));
 	if (!master) {
@@ -697,12 +709,26 @@ static int meson_spicc_probe(struct platform_device *pdev)
 		goto out_master;
 	}
 
+	if (spicc->data->has_pclk) {
+		spicc->pclk = devm_clk_get(&pdev->dev, "pclk");
+		if (IS_ERR(spicc->pclk)) {
+			dev_err(&pdev->dev, "pclk clock request failed\n");
+			ret = PTR_ERR(spicc->pclk);
+			goto out_master;
+		}
+	}
+
 	ret = clk_prepare_enable(spicc->core);
 	if (ret) {
 		dev_err(&pdev->dev, "core clock enable failed\n");
 		goto out_master;
 	}
-	rate = clk_get_rate(spicc->core);
+
+	ret = clk_prepare_enable(spicc->pclk);
+	if (ret) {
+		dev_err(&pdev->dev, "pclk clock enable failed\n");
+		goto out_master;
+	}
 
 	device_reset_optional(&pdev->dev);
 
@@ -715,6 +741,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 				     SPI_BPW_MASK(8);
 	master->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX);
 	master->min_speed_hz = spicc->data->min_speed_hz;
+	master->max_speed_hz = spicc->data->max_speed_hz;
 	master->setup = meson_spicc_setup;
 	master->cleanup = meson_spicc_cleanup;
 	master->prepare_message = meson_spicc_prepare_message;
@@ -722,10 +749,6 @@ static int meson_spicc_probe(struct platform_device *pdev)
 	master->transfer_one = meson_spicc_transfer_one;
 	master->use_gpio_descriptors = true;
 
-	/* Setup max rate according to the Meson datasheet */
-	master->max_speed_hz = min_t(unsigned int, rate >> 1,
-				     spicc->data->max_speed_hz);
-
 	meson_spicc_oen_enable(spicc);
 
 	ret = meson_spicc_clk_init(spicc);
@@ -744,6 +767,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 
 out_clk:
 	clk_disable_unprepare(spicc->core);
+	clk_disable_unprepare(spicc->pclk);
 
 out_master:
 	spi_master_put(master);
@@ -759,6 +783,7 @@ static int meson_spicc_remove(struct platform_device *pdev)
 	writel(0, spicc->base + SPICC_CONREG);
 
 	clk_disable_unprepare(spicc->core);
+	clk_disable_unprepare(spicc->pclk);
 
 	return 0;
 }
@@ -777,6 +802,15 @@ static const struct meson_spicc_data meson_spicc_axg_data = {
 	.has_enhance_clk_div	= true,
 };
 
+static const struct meson_spicc_data meson_spicc_g12a_data = {
+	.max_speed_hz		= 166666666,
+	.min_speed_hz		= 50000,
+	.fifo_size		= 15,
+	.has_oen		= true,
+	.has_enhance_clk_div	= true,
+	.has_pclk		= true,
+};
+
 static const struct of_device_id meson_spicc_of_match[] = {
 	{
 		.compatible	= "amlogic,meson-gx-spicc",
@@ -786,6 +820,10 @@ static const struct of_device_id meson_spicc_of_match[] = {
 		.compatible = "amlogic,meson-axg-spicc",
 		.data		= &meson_spicc_axg_data,
 	},
+	{
+		.compatible = "amlogic,meson-g12a-spicc",
+		.data		= &meson_spicc_g12a_data,
+	},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, meson_spicc_of_match);
-- 
2.20.1

Applied "spi: meson-spicc: adapt burst handling for G12A support" to the spi tree

[Mark Brown]

The patch

   spi: meson-spicc: adapt burst handling for G12A support

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 0eb707ac7dd7a4329d93d47feada6c9bb5ea8ee9 Mon Sep 17 00:00:00 2001
From: Neil Armstrong <narmstrong@baylibre.com>
Date: Thu, 12 Mar 2020 14:31:29 +0100
Subject: [PATCH] spi: meson-spicc: adapt burst handling for G12A support

The G12A SPICC controller variant has a different FIFO size and doesn't
handle the RX Half interrupt the same way as GXL & AXG variants.

Thus simplify the burst management and take in account a variable FIFO
size.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-8-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
---
 drivers/spi/spi-meson-spicc.c | 129 +++++++++++++---------------------
 1 file changed, 50 insertions(+), 79 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 4494a791f4a7..351ccd8dd2c2 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -141,12 +141,10 @@
 #define writel_bits_relaxed(mask, val, addr) \
 	writel_relaxed((readl_relaxed(addr) & ~(mask)) | (val), addr)
 
-#define SPICC_BURST_MAX	16
-#define SPICC_FIFO_HALF 10
-
 struct meson_spicc_data {
 	unsigned int			max_speed_hz;
 	unsigned int			min_speed_hz;
+	unsigned int			fifo_size;
 	bool				has_oen;
 	bool				has_enhance_clk_div;
 };
@@ -166,8 +164,6 @@ struct meson_spicc_device {
 	unsigned long			tx_remain;
 	unsigned long			rx_remain;
 	unsigned long			xfer_remain;
-	bool				is_burst_end;
-	bool				is_last_burst;
 };
 
 static void meson_spicc_oen_enable(struct meson_spicc_device *spicc)
@@ -191,7 +187,7 @@ static inline bool meson_spicc_txfull(struct meson_spicc_device *spicc)
 
 static inline bool meson_spicc_rxready(struct meson_spicc_device *spicc)
 {
-	return FIELD_GET(SPICC_RH | SPICC_RR | SPICC_RF_EN,
+	return FIELD_GET(SPICC_RH | SPICC_RR | SPICC_RF,
 			 readl_relaxed(spicc->base + SPICC_STATREG));
 }
 
@@ -246,34 +242,22 @@ static inline void meson_spicc_tx(struct meson_spicc_device *spicc)
 			       spicc->base + SPICC_TXDATA);
 }
 
-static inline u32 meson_spicc_setup_rx_irq(struct meson_spicc_device *spicc,
-					   u32 irq_ctrl)
+static inline void meson_spicc_setup_burst(struct meson_spicc_device *spicc)
 {
-	if (spicc->rx_remain > SPICC_FIFO_HALF)
-		irq_ctrl |= SPICC_RH_EN;
-	else
-		irq_ctrl |= SPICC_RR_EN;
-
-	return irq_ctrl;
-}
 
-static inline void meson_spicc_setup_burst(struct meson_spicc_device *spicc,
-					   unsigned int burst_len)
-{
+	unsigned int burst_len = min_t(unsigned int,
+				       spicc->xfer_remain /
+				       spicc->bytes_per_word,
+				       spicc->data->fifo_size);
 	/* Setup Xfer variables */
 	spicc->tx_remain = burst_len;
 	spicc->rx_remain = burst_len;
 	spicc->xfer_remain -= burst_len * spicc->bytes_per_word;
-	spicc->is_burst_end = false;
-	if (burst_len < SPICC_BURST_MAX || !spicc->xfer_remain)
-		spicc->is_last_burst = true;
-	else
-		spicc->is_last_burst = false;
 
 	/* Setup burst length */
 	writel_bits_relaxed(SPICC_BURSTLENGTH_MASK,
 			FIELD_PREP(SPICC_BURSTLENGTH_MASK,
-				burst_len),
+				burst_len - 1),
 			spicc->base + SPICC_CONREG);
 
 	/* Fill TX FIFO */
@@ -283,61 +267,26 @@ static inline void meson_spicc_setup_burst(struct meson_spicc_device *spicc,
 static irqreturn_t meson_spicc_irq(int irq, void *data)
 {
 	struct meson_spicc_device *spicc = (void *) data;
-	u32 ctrl = readl_relaxed(spicc->base + SPICC_INTREG);
-	u32 stat = readl_relaxed(spicc->base + SPICC_STATREG) & ctrl;
 
-	ctrl &= ~(SPICC_RH_EN | SPICC_RR_EN);
+	writel_bits_relaxed(SPICC_TC, SPICC_TC, spicc->base + SPICC_STATREG);
 
 	/* Empty RX FIFO */
 	meson_spicc_rx(spicc);
 
-	/* Enable TC interrupt since we transferred everything */
-	if (!spicc->tx_remain && !spicc->rx_remain) {
-		spicc->is_burst_end = true;
-
-		/* Enable TC interrupt */
-		ctrl |= SPICC_TC_EN;
-
-		/* Reload IRQ status */
-		stat = readl_relaxed(spicc->base + SPICC_STATREG) & ctrl;
-	}
-
-	/* Check transfer complete */
-	if ((stat & SPICC_TC) && spicc->is_burst_end) {
-		unsigned int burst_len;
-
-		/* Clear TC bit */
-		writel_relaxed(SPICC_TC, spicc->base + SPICC_STATREG);
-
-		/* Disable TC interrupt */
-		ctrl &= ~SPICC_TC_EN;
-
-		if (spicc->is_last_burst) {
-			/* Disable all IRQs */
-			writel(0, spicc->base + SPICC_INTREG);
-
-			spi_finalize_current_transfer(spicc->master);
+	if (!spicc->xfer_remain) {
+		/* Disable all IRQs */
+		writel(0, spicc->base + SPICC_INTREG);
 
-			return IRQ_HANDLED;
-		}
+		spi_finalize_current_transfer(spicc->master);
 
-		burst_len = min_t(unsigned int,
-				  spicc->xfer_remain / spicc->bytes_per_word,
-				  SPICC_BURST_MAX);
-
-		/* Setup burst */
-		meson_spicc_setup_burst(spicc, burst_len);
-
-		/* Restart burst */
-		writel_bits_relaxed(SPICC_XCH, SPICC_XCH,
-				    spicc->base + SPICC_CONREG);
+		return IRQ_HANDLED;
 	}
 
-	/* Setup RX interrupt trigger */
-	ctrl = meson_spicc_setup_rx_irq(spicc, ctrl);
+	/* Setup burst */
+	meson_spicc_setup_burst(spicc);
 
-	/* Reconfigure interrupts */
-	writel(ctrl, spicc->base + SPICC_INTREG);
+	/* Start burst */
+	writel_bits_relaxed(SPICC_XCH, SPICC_XCH, spicc->base + SPICC_CONREG);
 
 	return IRQ_HANDLED;
 }
@@ -405,6 +354,28 @@ static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 	clk_set_rate(spicc->clk, xfer->speed_hz);
 
 	meson_spicc_auto_io_delay(spicc);
+
+	writel_relaxed(0, spicc->base + SPICC_DMAREG);
+}
+
+static void meson_spicc_reset_fifo(struct meson_spicc_device *spicc)
+{
+	u32 data;
+
+	if (spicc->data->has_oen)
+		writel_bits_relaxed(SPICC_ENH_MAIN_CLK_AO,
+				    SPICC_ENH_MAIN_CLK_AO,
+				    spicc->base + SPICC_ENH_CTL0);
+
+	writel_bits_relaxed(SPICC_FIFORST_W1_MASK, SPICC_FIFORST_W1_MASK,
+			    spicc->base + SPICC_TESTREG);
+
+	while (meson_spicc_rxready(spicc))
+		data = readl_relaxed(spicc->base + SPICC_RXDATA);
+
+	if (spicc->data->has_oen)
+		writel_bits_relaxed(SPICC_ENH_MAIN_CLK_AO, 0,
+				    spicc->base + SPICC_ENH_CTL0);
 }
 
 static int meson_spicc_transfer_one(struct spi_master *master,
@@ -412,8 +383,6 @@ static int meson_spicc_transfer_one(struct spi_master *master,
 				    struct spi_transfer *xfer)
 {
 	struct meson_spicc_device *spicc = spi_master_get_devdata(master);
-	unsigned int burst_len;
-	u32 irq = 0;
 
 	/* Store current transfer */
 	spicc->xfer = xfer;
@@ -427,22 +396,22 @@ static int meson_spicc_transfer_one(struct spi_master *master,
 	spicc->bytes_per_word =
 	   DIV_ROUND_UP(spicc->xfer->bits_per_word, 8);
 
+	if (xfer->len % spicc->bytes_per_word)
+		return -EINVAL;
+
 	/* Setup transfer parameters */
 	meson_spicc_setup_xfer(spicc, xfer);
 
-	burst_len = min_t(unsigned int,
-			  spicc->xfer_remain / spicc->bytes_per_word,
-			  SPICC_BURST_MAX);
-
-	meson_spicc_setup_burst(spicc, burst_len);
+	meson_spicc_reset_fifo(spicc);
 
-	irq = meson_spicc_setup_rx_irq(spicc, irq);
+	/* Setup burst */
+	meson_spicc_setup_burst(spicc);
 
 	/* Start burst */
 	writel_bits_relaxed(SPICC_XCH, SPICC_XCH, spicc->base + SPICC_CONREG);
 
 	/* Enable interrupts */
-	writel_relaxed(irq, spicc->base + SPICC_INTREG);
+	writel_relaxed(SPICC_TC_EN, spicc->base + SPICC_INTREG);
 
 	return 1;
 }
@@ -499,7 +468,7 @@ static int meson_spicc_prepare_message(struct spi_master *master,
 	/* Setup no wait cycles by default */
 	writel_relaxed(0, spicc->base + SPICC_PERIODREG);
 
-	writel_bits_relaxed(BIT(24), BIT(24), spicc->base + SPICC_TESTREG);
+	writel_bits_relaxed(SPICC_LBC_W1, 0, spicc->base + SPICC_TESTREG);
 
 	return 0;
 }
@@ -797,11 +766,13 @@ static int meson_spicc_remove(struct platform_device *pdev)
 static const struct meson_spicc_data meson_spicc_gx_data = {
 	.max_speed_hz		= 30000000,
 	.min_speed_hz		= 325000,
+	.fifo_size		= 16,
 };
 
 static const struct meson_spicc_data meson_spicc_axg_data = {
 	.max_speed_hz		= 80000000,
 	.min_speed_hz		= 325000,
+	.fifo_size		= 16,
 	.has_oen		= true,
 	.has_enhance_clk_div	= true,
 };
-- 
2.20.1

Applied "spi: meson-spicc: setup IO line delay" to the spi tree

[Mark Brown]

The patch

   spi: meson-spicc: setup IO line delay

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From f27bff479ea3de9ca325d4f8e8c8b49a87d6b0c5 Mon Sep 17 00:00:00 2001
From: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Date: Thu, 12 Mar 2020 14:31:28 +0100
Subject: [PATCH] spi: meson-spicc: setup IO line delay

Now the controller can support frequencies higher than 30MHz, we need
the setup the I/O line delays in regard of the SPI clock frequency.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Link: https://lore.kernel.org/r/20200312133131.26430-7-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org
Signed-off-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 61 ++++++++++++++++++++++++++++++++++-
 1 file changed, 60 insertions(+), 1 deletion(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index b5bd3a897e8f..4494a791f4a7 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -106,7 +106,21 @@
 #define SPICC_SWAP_RO		BIT(14) /* RX FIFO Data Swap Read-Only */
 #define SPICC_SWAP_W1		BIT(15) /* RX FIFO Data Swap Write-Only */
 #define SPICC_DLYCTL_RO_MASK	GENMASK(20, 15) /* Delay Control Read-Only */
-#define SPICC_DLYCTL_W1_MASK	GENMASK(21, 16) /* Delay Control Write-Only */
+#define SPICC_MO_DELAY_MASK	GENMASK(17, 16) /* Master Output Delay */
+#define SPICC_MO_NO_DELAY	0
+#define SPICC_MO_DELAY_1_CYCLE	1
+#define SPICC_MO_DELAY_2_CYCLE	2
+#define SPICC_MO_DELAY_3_CYCLE	3
+#define SPICC_MI_DELAY_MASK	GENMASK(19, 18) /* Master Input Delay */
+#define SPICC_MI_NO_DELAY	0
+#define SPICC_MI_DELAY_1_CYCLE	1
+#define SPICC_MI_DELAY_2_CYCLE	2
+#define SPICC_MI_DELAY_3_CYCLE	3
+#define SPICC_MI_CAP_DELAY_MASK	GENMASK(21, 20) /* Master Capture Delay */
+#define SPICC_CAP_AHEAD_2_CYCLE	0
+#define SPICC_CAP_AHEAD_1_CYCLE	1
+#define SPICC_CAP_NO_DELAY	2
+#define SPICC_CAP_DELAY_1_CYCLE	3
 #define SPICC_FIFORST_RO_MASK	GENMASK(22, 21) /* FIFO Softreset Read-Only */
 #define SPICC_FIFORST_W1_MASK	GENMASK(23, 22) /* FIFO Softreset Write-Only */
 
@@ -328,6 +342,49 @@ static irqreturn_t meson_spicc_irq(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
+static void meson_spicc_auto_io_delay(struct meson_spicc_device *spicc)
+{
+	u32 div, hz;
+	u32 mi_delay, cap_delay;
+	u32 conf;
+
+	if (spicc->data->has_enhance_clk_div) {
+		div = FIELD_GET(SPICC_ENH_DATARATE_MASK,
+				readl_relaxed(spicc->base + SPICC_ENH_CTL0));
+		div++;
+		div <<= 1;
+	} else {
+		div = FIELD_GET(SPICC_DATARATE_MASK,
+				readl_relaxed(spicc->base + SPICC_CONREG));
+		div += 2;
+		div = 1 << div;
+	}
+
+	mi_delay = SPICC_MI_NO_DELAY;
+	cap_delay = SPICC_CAP_AHEAD_2_CYCLE;
+	hz = clk_get_rate(spicc->clk);
+
+	if (hz >= 100000000)
+		cap_delay = SPICC_CAP_DELAY_1_CYCLE;
+	else if (hz >= 80000000)
+		cap_delay = SPICC_CAP_NO_DELAY;
+	else if (hz >= 40000000)
+		cap_delay = SPICC_CAP_AHEAD_1_CYCLE;
+	else if (div >= 16)
+		mi_delay = SPICC_MI_DELAY_3_CYCLE;
+	else if (div >= 8)
+		mi_delay = SPICC_MI_DELAY_2_CYCLE;
+	else if (div >= 6)
+		mi_delay = SPICC_MI_DELAY_1_CYCLE;
+
+	conf = readl_relaxed(spicc->base + SPICC_TESTREG);
+	conf &= ~(SPICC_MO_DELAY_MASK | SPICC_MI_DELAY_MASK
+		  | SPICC_MI_CAP_DELAY_MASK);
+	conf |= FIELD_PREP(SPICC_MI_DELAY_MASK, mi_delay);
+	conf |= FIELD_PREP(SPICC_MI_CAP_DELAY_MASK, cap_delay);
+	writel_relaxed(conf, spicc->base + SPICC_TESTREG);
+}
+
 static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 				   struct spi_transfer *xfer)
 {
@@ -346,6 +403,8 @@ static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 		writel_relaxed(conf, spicc->base + SPICC_CONREG);
 
 	clk_set_rate(spicc->clk, xfer->speed_hz);
+
+	meson_spicc_auto_io_delay(spicc);
 }
 
 static int meson_spicc_transfer_one(struct spi_master *master,
-- 
2.20.1

Applied "spi: meson-spicc: add min sclk for each compatible" to the spi tree

[Mark Brown]

The patch

   spi: meson-spicc: add min sclk for each compatible

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 8791068dab979819e01f41736953b9b2e462867b Mon Sep 17 00:00:00 2001
From: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Date: Thu, 12 Mar 2020 14:31:27 +0100
Subject: [PATCH] spi: meson-spicc: add min sclk for each compatible

The G12A SPICC controller variant takes the source clock from a specific
clock instead of the bus clock.
The minimal clock calculus won't work with the G12A support, thus add the
minimal supported clock for each variant and pass this to the SPI core.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Link: https://lore.kernel.org/r/20200312133131.26430-6-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org
Signed-off-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 710b4e780daa..b5bd3a897e8f 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -132,6 +132,7 @@
 
 struct meson_spicc_data {
 	unsigned int			max_speed_hz;
+	unsigned int			min_speed_hz;
 	bool				has_oen;
 	bool				has_enhance_clk_div;
 };
@@ -685,7 +686,7 @@ static int meson_spicc_probe(struct platform_device *pdev)
 				     SPI_BPW_MASK(16) |
 				     SPI_BPW_MASK(8);
 	master->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX);
-	master->min_speed_hz = rate >> 9;
+	master->min_speed_hz = spicc->data->min_speed_hz;
 	master->setup = meson_spicc_setup;
 	master->cleanup = meson_spicc_cleanup;
 	master->prepare_message = meson_spicc_prepare_message;
@@ -736,10 +737,12 @@ static int meson_spicc_remove(struct platform_device *pdev)
 
 static const struct meson_spicc_data meson_spicc_gx_data = {
 	.max_speed_hz		= 30000000,
+	.min_speed_hz		= 325000,
 };
 
 static const struct meson_spicc_data meson_spicc_axg_data = {
 	.max_speed_hz		= 80000000,
+	.min_speed_hz		= 325000,
 	.has_oen		= true,
 	.has_enhance_clk_div	= true,
 };
-- 
2.20.1

Applied "spi: meson-spicc: support max 80MHz clock" to the spi tree

[Mark Brown]

The patch

   spi: meson-spicc: support max 80MHz clock

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 3196816ff64bb3a21fbda89e7355b6b87c3f50a0 Mon Sep 17 00:00:00 2001
From: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Date: Thu, 12 Mar 2020 14:31:26 +0100
Subject: [PATCH] spi: meson-spicc: support max 80MHz clock

The SPICC controller in Meson-AXG is capable of running at 80M clock.
The ASIC IP is improved and the clock is actually running higher than
previous old SoCs.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Signed-off-by: Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Sunny Luo <sunny.luo-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Link: https://lore.kernel.org/r/20200312133131.26430-5-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org
Signed-off-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index bd434d9055d9..710b4e780daa 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -35,7 +35,6 @@
  *   to have a CS go down over the full transfer
  */
 
-#define SPICC_MAX_FREQ	30000000
 #define SPICC_MAX_BURST	128
 
 /* Register Map */
@@ -132,6 +131,7 @@
 #define SPICC_FIFO_HALF 10
 
 struct meson_spicc_data {
+	unsigned int			max_speed_hz;
 	bool				has_oen;
 	bool				has_enhance_clk_div;
 };
@@ -693,11 +693,9 @@ static int meson_spicc_probe(struct platform_device *pdev)
 	master->transfer_one = meson_spicc_transfer_one;
 	master->use_gpio_descriptors = true;
 
-	/* Setup max rate according to the Meson GX datasheet */
-	if ((rate >> 2) > SPICC_MAX_FREQ)
-		master->max_speed_hz = SPICC_MAX_FREQ;
-	else
-		master->max_speed_hz = rate >> 2;
+	/* Setup max rate according to the Meson datasheet */
+	master->max_speed_hz = min_t(unsigned int, rate >> 1,
+				     spicc->data->max_speed_hz);
 
 	meson_spicc_oen_enable(spicc);
 
@@ -737,9 +735,11 @@ static int meson_spicc_remove(struct platform_device *pdev)
 }
 
 static const struct meson_spicc_data meson_spicc_gx_data = {
+	.max_speed_hz		= 30000000,
 };
 
 static const struct meson_spicc_data meson_spicc_axg_data = {
+	.max_speed_hz		= 80000000,
 	.has_oen		= true,
 	.has_enhance_clk_div	= true,
 };
-- 
2.20.1

Applied "spi: meson-spicc: add a linear clock divider support" to the spi tree

[Mark Brown]

The patch

   spi: meson-spicc: add a linear clock divider support

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 3e0cf4d3fc2985beee011e9a1bbb8374fc02c0a0 Mon Sep 17 00:00:00 2001
From: Sunny Luo <sunny.luo-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Date: Thu, 12 Mar 2020 14:31:25 +0100
Subject: [PATCH] spi: meson-spicc: add a linear clock divider support

The SPICC controller in Meson-AXG SoC is capable of using
a linear clock divider to reach a much fine tuned range of clocks,
while the old controller only use a power of two clock divider,
result at a more coarse clock range.

Also convert the clock registration into Common Clock Framework.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Signed-off-by: Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Sunny Luo <sunny.luo-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Link: https://lore.kernel.org/r/20200312133131.26430-4-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org
Signed-off-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/Kconfig           |   1 +
 drivers/spi/spi-meson-spicc.c | 204 +++++++++++++++++++++++++++-------
 2 files changed, 165 insertions(+), 40 deletions(-)

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index c33ca96b44de..efce98e9844e 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -428,6 +428,7 @@ config SPI_FSL_ESPI
 
 config SPI_MESON_SPICC
 	tristate "Amlogic Meson SPICC controller"
+	depends on COMMON_CLK
 	depends on ARCH_MESON || COMPILE_TEST
 	help
 	  This enables master mode support for the SPICC (SPI communication
diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index ba70ef94a82a..bd434d9055d9 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -116,6 +116,9 @@
 #define SPICC_DWADDR	0x24	/* Write Address of DMA */
 
 #define SPICC_ENH_CTL0	0x38	/* Enhanced Feature */
+#define SPICC_ENH_CLK_CS_DELAY_MASK	GENMASK(15, 0)
+#define SPICC_ENH_DATARATE_MASK		GENMASK(23, 16)
+#define SPICC_ENH_DATARATE_EN		BIT(24)
 #define SPICC_ENH_MOSI_OEN		BIT(25)
 #define SPICC_ENH_CLK_OEN		BIT(26)
 #define SPICC_ENH_CS_OEN		BIT(27)
@@ -130,6 +133,7 @@
 
 struct meson_spicc_data {
 	bool				has_oen;
+	bool				has_enhance_clk_div;
 };
 
 struct meson_spicc_device {
@@ -137,6 +141,7 @@ struct meson_spicc_device {
 	struct platform_device		*pdev;
 	void __iomem			*base;
 	struct clk			*core;
+	struct clk			*clk;
 	struct spi_message		*message;
 	struct spi_transfer		*xfer;
 	const struct meson_spicc_data	*data;
@@ -322,40 +327,6 @@ static irqreturn_t meson_spicc_irq(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
-static u32 meson_spicc_setup_speed(struct meson_spicc_device *spicc, u32 conf,
-				   u32 speed)
-{
-	unsigned long parent, value;
-	unsigned int i, div;
-
-	parent = clk_get_rate(spicc->core);
-
-	/* Find closest inferior/equal possible speed */
-	for (i = 0 ; i < 7 ; ++i) {
-		/* 2^(data_rate+2) */
-		value = parent >> (i + 2);
-
-		if (value <= speed)
-			break;
-	}
-
-	/* If provided speed it lower than max divider, use max divider */
-	if (i > 7) {
-		div = 7;
-		dev_warn_once(&spicc->pdev->dev, "unable to get close to speed %u\n",
-			      speed);
-	} else
-		div = i;
-
-	dev_dbg(&spicc->pdev->dev, "parent %lu, speed %u -> %lu (%u)\n",
-		parent, speed, value, div);
-
-	conf &= ~SPICC_DATARATE_MASK;
-	conf |= FIELD_PREP(SPICC_DATARATE_MASK, div);
-
-	return conf;
-}
-
 static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 				   struct spi_transfer *xfer)
 {
@@ -364,9 +335,6 @@ static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 	/* Read original configuration */
 	conf = conf_orig = readl_relaxed(spicc->base + SPICC_CONREG);
 
-	/* Select closest divider */
-	conf = meson_spicc_setup_speed(spicc, conf, xfer->speed_hz);
-
 	/* Setup word width */
 	conf &= ~SPICC_BITLENGTH_MASK;
 	conf |= FIELD_PREP(SPICC_BITLENGTH_MASK,
@@ -375,6 +343,8 @@ static void meson_spicc_setup_xfer(struct meson_spicc_device *spicc,
 	/* Ignore if unchanged */
 	if (conf != conf_orig)
 		writel_relaxed(conf, spicc->base + SPICC_CONREG);
+
+	clk_set_rate(spicc->clk, xfer->speed_hz);
 }
 
 static int meson_spicc_transfer_one(struct spi_master *master,
@@ -481,9 +451,6 @@ static int meson_spicc_unprepare_transfer(struct spi_master *master)
 	/* Disable all IRQs */
 	writel(0, spicc->base + SPICC_INTREG);
 
-	/* Disable controller */
-	writel_bits_relaxed(SPICC_ENABLE, 0, spicc->base + SPICC_CONREG);
-
 	device_reset_optional(&spicc->pdev->dev);
 
 	return 0;
@@ -502,6 +469,152 @@ static void meson_spicc_cleanup(struct spi_device *spi)
 	spi->controller_state = NULL;
 }
 
+/*
+ * The Clock Mux
+ *            x-----------------x   x------------x    x------\
+ *        |---| pow2 fixed div  |---| pow2 div   |----|      |
+ *        |   x-----------------x   x------------x    |      |
+ * src ---|                                           | mux  |-- out
+ *        |   x-----------------x   x------------x    |      |
+ *        |---| enh fixed div   |---| enh div    |0---|      |
+ *            x-----------------x   x------------x    x------/
+ *
+ * Clk path for GX series:
+ *    src -> pow2 fixed div -> pow2 div -> out
+ *
+ * Clk path for AXG series:
+ *    src -> pow2 fixed div -> pow2 div -> mux -> out
+ *    src -> enh fixed div -> enh div -> mux -> out
+ */
+
+static int meson_spicc_clk_init(struct meson_spicc_device *spicc)
+{
+	struct device *dev = &spicc->pdev->dev;
+	struct clk_fixed_factor *pow2_fixed_div, *enh_fixed_div;
+	struct clk_divider *pow2_div, *enh_div;
+	struct clk_mux *mux;
+	struct clk_init_data init;
+	struct clk *clk;
+	struct clk_parent_data parent_data[2];
+	char name[64];
+
+	memset(&init, 0, sizeof(init));
+	memset(&parent_data, 0, sizeof(parent_data));
+
+	init.parent_data = parent_data;
+
+	/* algorithm for pow2 div: rate = freq / 4 / (2 ^ N) */
+
+	pow2_fixed_div = devm_kzalloc(dev, sizeof(*pow2_fixed_div), GFP_KERNEL);
+	if (!pow2_fixed_div)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#pow2_fixed_div", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_fixed_factor_ops;
+	init.flags = 0;
+	parent_data[0].hw = __clk_get_hw(spicc->core);
+	init.num_parents = 1;
+
+	pow2_fixed_div->mult = 1,
+	pow2_fixed_div->div = 4,
+	pow2_fixed_div->hw.init = &init;
+
+	clk = devm_clk_register(dev, &pow2_fixed_div->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	pow2_div = devm_kzalloc(dev, sizeof(*pow2_div), GFP_KERNEL);
+	if (!pow2_div)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#pow2_div", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_divider_ops;
+	init.flags = CLK_SET_RATE_PARENT;
+	parent_data[0].hw = &pow2_fixed_div->hw;
+	init.num_parents = 1;
+
+	pow2_div->shift = 16,
+	pow2_div->width = 3,
+	pow2_div->flags = CLK_DIVIDER_POWER_OF_TWO,
+	pow2_div->reg = spicc->base + SPICC_CONREG;
+	pow2_div->hw.init = &init;
+
+	clk = devm_clk_register(dev, &pow2_div->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	if (!spicc->data->has_enhance_clk_div) {
+		spicc->clk = clk;
+		return 0;
+	}
+
+	/* algorithm for enh div: rate = freq / 2 / (N + 1) */
+
+	enh_fixed_div = devm_kzalloc(dev, sizeof(*enh_fixed_div), GFP_KERNEL);
+	if (!enh_fixed_div)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#enh_fixed_div", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_fixed_factor_ops;
+	init.flags = 0;
+	parent_data[0].hw = __clk_get_hw(spicc->core);
+	init.num_parents = 1;
+
+	enh_fixed_div->mult = 1,
+	enh_fixed_div->div = 2,
+	enh_fixed_div->hw.init = &init;
+
+	clk = devm_clk_register(dev, &enh_fixed_div->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	enh_div = devm_kzalloc(dev, sizeof(*enh_div), GFP_KERNEL);
+	if (!enh_div)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#enh_div", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_divider_ops;
+	init.flags = CLK_SET_RATE_PARENT;
+	parent_data[0].hw = &enh_fixed_div->hw;
+	init.num_parents = 1;
+
+	enh_div->shift	= 16,
+	enh_div->width	= 8,
+	enh_div->reg = spicc->base + SPICC_ENH_CTL0;
+	enh_div->hw.init = &init;
+
+	clk = devm_clk_register(dev, &enh_div->hw);
+	if (WARN_ON(IS_ERR(clk)))
+		return PTR_ERR(clk);
+
+	mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
+	if (!mux)
+		return -ENOMEM;
+
+	snprintf(name, sizeof(name), "%s#sel", dev_name(dev));
+	init.name = name;
+	init.ops = &clk_mux_ops;
+	parent_data[0].hw = &pow2_div->hw;
+	parent_data[1].hw = &enh_div->hw;
+	init.num_parents = 2;
+	init.flags = CLK_SET_RATE_PARENT;
+
+	mux->mask = 0x1,
+	mux->shift = 24,
+	mux->reg = spicc->base + SPICC_ENH_CTL0;
+	mux->hw.init = &init;
+
+	spicc->clk = devm_clk_register(dev, &mux->hw);
+	if (WARN_ON(IS_ERR(spicc->clk)))
+		return PTR_ERR(spicc->clk);
+
+	return 0;
+}
+
 static int meson_spicc_probe(struct platform_device *pdev)
 {
 	struct spi_master *master;
@@ -533,6 +646,10 @@ static int meson_spicc_probe(struct platform_device *pdev)
 		goto out_master;
 	}
 
+	/* Set master mode and enable controller */
+	writel_relaxed(SPICC_ENABLE | SPICC_MODE_MASTER,
+		       spicc->base + SPICC_CONREG);
+
 	/* Disable all IRQs */
 	writel_relaxed(0, spicc->base + SPICC_INTREG);
 
@@ -584,6 +701,12 @@ static int meson_spicc_probe(struct platform_device *pdev)
 
 	meson_spicc_oen_enable(spicc);
 
+	ret = meson_spicc_clk_init(spicc);
+	if (ret) {
+		dev_err(&pdev->dev, "clock registration failed\n");
+		goto out_master;
+	}
+
 	ret = devm_spi_register_master(&pdev->dev, master);
 	if (ret) {
 		dev_err(&pdev->dev, "spi master registration failed\n");
@@ -618,6 +741,7 @@ static const struct meson_spicc_data meson_spicc_gx_data = {
 
 static const struct meson_spicc_data meson_spicc_axg_data = {
 	.has_oen		= true,
+	.has_enhance_clk_div	= true,
 };
 
 static const struct of_device_id meson_spicc_of_match[] = {
-- 
2.20.1

Applied "spi: meson-spicc: enhance output enable feature" to the spi tree

[Mark Brown]

The patch

   spi: meson-spicc: enhance output enable feature

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From a6cda1f905b4a5442eecce94bda1e136f7e1e539 Mon Sep 17 00:00:00 2001
From: Sunny Luo <sunny.luo-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Date: Thu, 12 Mar 2020 14:31:24 +0100
Subject: [PATCH] spi: meson-spicc: enhance output enable feature

The SPICC controller in Meson-AXG is capable of driving the CLK/MOSI/SS
signal lines through the idle state (between two transmission operation),
which avoid the signals floating in unexpected state.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Signed-off-by: Yixun Lan <yixun.lan-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Signed-off-by: Sunny Luo <sunny.luo-LpR1jeaWuhtBDgjK7y7TUQ@public.gmane.org>
Link: https://lore.kernel.org/r/20200312133131.26430-3-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org
Signed-off-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 53 +++++++++++++++++++++++++++++++++--
 1 file changed, 51 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 8425e5ae1273..ba70ef94a82a 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -9,11 +9,13 @@
 
 #include <linux/bitfield.h>
 #include <linux/clk.h>
+#include <linux/clk-provider.h>
 #include <linux/device.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
 #include <linux/types.h>
@@ -113,12 +115,23 @@
 
 #define SPICC_DWADDR	0x24	/* Write Address of DMA */
 
+#define SPICC_ENH_CTL0	0x38	/* Enhanced Feature */
+#define SPICC_ENH_MOSI_OEN		BIT(25)
+#define SPICC_ENH_CLK_OEN		BIT(26)
+#define SPICC_ENH_CS_OEN		BIT(27)
+#define SPICC_ENH_CLK_CS_DELAY_EN	BIT(28)
+#define SPICC_ENH_MAIN_CLK_AO		BIT(29)
+
 #define writel_bits_relaxed(mask, val, addr) \
 	writel_relaxed((readl_relaxed(addr) & ~(mask)) | (val), addr)
 
 #define SPICC_BURST_MAX	16
 #define SPICC_FIFO_HALF 10
 
+struct meson_spicc_data {
+	bool				has_oen;
+};
+
 struct meson_spicc_device {
 	struct spi_master		*master;
 	struct platform_device		*pdev;
@@ -126,6 +139,7 @@ struct meson_spicc_device {
 	struct clk			*core;
 	struct spi_message		*message;
 	struct spi_transfer		*xfer;
+	const struct meson_spicc_data	*data;
 	u8				*tx_buf;
 	u8				*rx_buf;
 	unsigned int			bytes_per_word;
@@ -136,6 +150,19 @@ struct meson_spicc_device {
 	bool				is_last_burst;
 };
 
+static void meson_spicc_oen_enable(struct meson_spicc_device *spicc)
+{
+	u32 conf;
+
+	if (!spicc->data->has_oen)
+		return;
+
+	conf = readl_relaxed(spicc->base + SPICC_ENH_CTL0) |
+		SPICC_ENH_MOSI_OEN | SPICC_ENH_CLK_OEN | SPICC_ENH_CS_OEN;
+
+	writel_relaxed(conf, spicc->base + SPICC_ENH_CTL0);
+}
+
 static inline bool meson_spicc_txfull(struct meson_spicc_device *spicc)
 {
 	return !!FIELD_GET(SPICC_TF,
@@ -489,6 +516,13 @@ static int meson_spicc_probe(struct platform_device *pdev)
 	spicc = spi_master_get_devdata(master);
 	spicc->master = master;
 
+	spicc->data = of_device_get_match_data(&pdev->dev);
+	if (!spicc->data) {
+		dev_err(&pdev->dev, "failed to get match data\n");
+		ret = -EINVAL;
+		goto out_master;
+	}
+
 	spicc->pdev = pdev;
 	platform_set_drvdata(pdev, spicc);
 
@@ -548,6 +582,8 @@ static int meson_spicc_probe(struct platform_device *pdev)
 	else
 		master->max_speed_hz = rate >> 2;
 
+	meson_spicc_oen_enable(spicc);
+
 	ret = devm_spi_register_master(&pdev->dev, master);
 	if (ret) {
 		dev_err(&pdev->dev, "spi master registration failed\n");
@@ -577,9 +613,22 @@ static int meson_spicc_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct meson_spicc_data meson_spicc_gx_data = {
+};
+
+static const struct meson_spicc_data meson_spicc_axg_data = {
+	.has_oen		= true,
+};
+
 static const struct of_device_id meson_spicc_of_match[] = {
-	{ .compatible = "amlogic,meson-gx-spicc", },
-	{ .compatible = "amlogic,meson-axg-spicc", },
+	{
+		.compatible	= "amlogic,meson-gx-spicc",
+		.data		= &meson_spicc_gx_data,
+	},
+	{
+		.compatible = "amlogic,meson-axg-spicc",
+		.data		= &meson_spicc_axg_data,
+	},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, meson_spicc_of_match);
-- 
2.20.1

Applied "spi: meson-spicc: remove unused variables" to the spi tree

[Mark Brown]

The patch

   spi: meson-spicc: remove unused variables

has been applied to the spi tree at

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From b9dfb20eed5c7dab37d6267a985dbe16df9e4293 Mon Sep 17 00:00:00 2001
From: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Date: Thu, 12 Mar 2020 14:31:23 +0100
Subject: [PATCH] spi: meson-spicc: remove unused variables

Remove unused variables from spicc data struct.

Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Link: https://lore.kernel.org/r/20200312133131.26430-2-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org
Signed-off-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi-meson-spicc.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/spi/spi-meson-spicc.c b/drivers/spi/spi-meson-spicc.c
index 7f5680fe2568..8425e5ae1273 100644
--- a/drivers/spi/spi-meson-spicc.c
+++ b/drivers/spi/spi-meson-spicc.c
@@ -130,9 +130,7 @@ struct meson_spicc_device {
 	u8				*rx_buf;
 	unsigned int			bytes_per_word;
 	unsigned long			tx_remain;
-	unsigned long			txb_remain;
 	unsigned long			rx_remain;
-	unsigned long			rxb_remain;
 	unsigned long			xfer_remain;
 	bool				is_burst_end;
 	bool				is_last_burst;
-- 
2.20.1