Linux-SPI Archive on lore.kernel.org
 help / color / Atom feed
From: Pratyush Yadav <p.yadav@ti.com>
To: Nishanth Menon <nm@ti.com>, Tero Kristo <kristo@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Tudor Ambarus <tudor.ambarus@microchip.com>,
	Michael Walle <michael@walle.cc>,
	Miquel Raynal <miquel.raynal@bootlin.com>,
	Richard Weinberger <richard@nod.at>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Mark Brown <broonie@kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<linux-mtd@lists.infradead.org>, <linux-spi@vger.kernel.org>
Cc: Pratyush Yadav <p.yadav@ti.com>, Lokesh Vutla <lokeshvutla@ti.com>
Subject: [RFC PATCH 6/6] arm64: dts: ti: k3-j721e-som-p0: Enable PHY calibration
Date: Fri, 12 Mar 2021 00:42:16 +0530
Message-ID: <20210311191216.7363-7-p.yadav@ti.com> (raw)
In-Reply-To: <20210311191216.7363-1-p.yadav@ti.com>

For running the flash in 8D-8D-8D mode at 166 MHz (controller ref clock
speed), PHY calibration procedure needs to run to calculate the proper
line delays.

To perform this calibration, the controller needs to know the location
of the pre-determined calibration pattern on the flash. Add a fixed
partition table that contains the calibration partition, along with the
rest of the partitions for the platform. Also add a nvmem cell that
points to the calibration partition.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---

Based on patch
https://patchwork.kernel.org/project/linux-arm-kernel/patch/20210305153926.3479-2-p.yadav@ti.com/

 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 55 +++++++++++++++++++++
 1 file changed, 55 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index 2fee2906183d..6013ebb45517 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -170,6 +170,8 @@ J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
 &ospi0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+	nvmem-cells = <&ospi_calibration_data>;
+	nvmem-cell-names = "calibration";

 	flash@0{
 		compatible = "jedec,spi-nor";
@@ -184,6 +186,59 @@ flash@0{
 		cdns,read-delay = <0>;
 		#address-cells = <1>;
 		#size-cells = <1>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partiiton@0 {
+				label = "ospi.tiboot3";
+				reg = <0x0 0x80000>;
+			};
+
+			partition@80000 {
+				label = "ospi.tispl";
+				reg = <0x80000 0x200000>;
+			};
+
+			partition@280000 {
+				label = "ospi.u-boot";
+				reg = <0x280000 0x400000>;
+			};
+
+			partition@680000 {
+				label = "ospi.env";
+				reg = <0x680000 0x20000>;
+			};
+
+			partition@6a0000 {
+				label = "ospi.env.backup";
+				reg = <0x6a0000 0x20000>;
+			};
+
+			partition@0x6c0000 {
+				label = "ospi.sysfw";
+				reg = <0x6c0000 0x100000>;
+			};
+
+			partition@800000 {
+				label = "ospi.rootfs";
+				reg = <0x800000 0x37e0000>;
+			};
+
+			calibration_partition: partition@3fe0000 {
+				compatible = "nvmem-cells";
+				label = "ospi.phypattern";
+				reg = <0x3fe0000 0x20000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				ospi_calibration_data: ospi-calibration-cell@0 {
+					reg = <0x0 0x80>;
+				};
+			};
+		};
 	};
 };

--
2.30.0


  parent reply index

Thread overview: 33+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-03-11 19:12 [RFC PATCH 0/6] spi: Add OSPI PHY calibration support for spi-cadence-quadspi Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 1/6] spi: spi-mem: Tell controller when device is ready for calibration Pratyush Yadav
2021-03-23 23:07   ` Michael Walle
2021-03-24  8:08     ` Pratyush Yadav
2021-04-29 16:23       ` Michael Walle
2021-04-29 18:41         ` Pratyush Yadav
2021-04-29 22:46           ` Michael Walle
2021-03-11 19:12 ` [RFC PATCH 2/6] mtd: spi-nor: core: consolidate read op creation Pratyush Yadav
2021-03-23 23:17   ` Michael Walle
2021-03-24  8:04     ` Pratyush Yadav
2021-04-08 12:48   ` Michael Walle
2021-03-11 19:12 ` [RFC PATCH 3/6] mtd: spi-nor: core: run calibration when initialization is done Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 4/6] spi: cadence-qspi: Use PHY for DAC reads if possible Pratyush Yadav
2021-03-12  9:13   ` Tudor.Ambarus
2021-03-12 10:17     ` Pratyush Yadav
2021-04-29 16:28       ` Michael Walle
2021-04-29 18:19         ` Pratyush Yadav
2021-04-29 22:20           ` Michael Walle
2021-05-10 11:39             ` Pratyush Yadav
2021-03-11 19:12 ` [RFC PATCH 5/6] spi: cadence-qspi: Tune PHY to allow running at higher frequencies Pratyush Yadav
2021-04-29 22:48   ` Michael Walle
2021-04-30  5:42     ` Pratyush Yadav
2021-03-11 19:12 ` Pratyush Yadav [this message]
2021-03-12  9:09 ` [RFC PATCH 0/6] spi: Add OSPI PHY calibration support for spi-cadence-quadspi Tudor.Ambarus
2021-03-12 10:10   ` Pratyush Yadav
2021-03-12 10:20     ` Michael Walle
2021-03-12 11:07       ` Pratyush Yadav
2021-03-12 13:26         ` Michael Walle
2021-03-12 11:23     ` Tudor.Ambarus
2021-03-12 18:14       ` Pratyush Yadav
2021-03-12 13:32 ` Michael Walle
2021-03-12 14:59   ` Tudor.Ambarus
2021-03-12 17:00   ` Pratyush Yadav

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210311191216.7363-7-p.yadav@ti.com \
    --to=p.yadav@ti.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=kristo@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=lokeshvutla@ti.com \
    --cc=michael@walle.cc \
    --cc=miquel.raynal@bootlin.com \
    --cc=nm@ti.com \
    --cc=richard@nod.at \
    --cc=robh+dt@kernel.org \
    --cc=tudor.ambarus@microchip.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-SPI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-spi/0 linux-spi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-spi linux-spi/ https://lore.kernel.org/linux-spi \
		linux-spi@vger.kernel.org
	public-inbox-index linux-spi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-spi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git