linux-spi.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Pratyush Yadav <p.yadav@ti.com>
To: Kuldeep Singh <kuldeep.singh@nxp.com>
Cc: <linux-spi@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>, Mark Brown <broonie@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Vladimir Oltean <olteanv@gmail.com>,
	<linux-mtd@lists.infradead.org>
Subject: Re: [PATCH] dt-bindings: spi: Convert Freescale DSPI to json schema
Date: Tue, 16 Mar 2021 00:00:52 +0530	[thread overview]
Message-ID: <20210315183051.ugvmz4zqrvuo6iqq@ti.com> (raw)
In-Reply-To: <20210315121518.3710171-1-kuldeep.singh@nxp.com>

+Cc mtd list

Hi,

On 15/03/21 05:45PM, Kuldeep Singh wrote:
> Convert the Freescale DSPI binding to DT schema format using json-schema.
> 
> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
> ---
> Hi Rob,
> This patch is checked with following commands with no warnings observed.
> make distclean; make allmodconfig;
> make dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/fsl,spi-fsl-dspi.yaml;
> make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/fsl,spi-fsl-dspi.yaml

When I add the "fsl,spi-cs-sck-delay" property under the flash@0 node in 
the example and run dt_binding_check, I see the below error:

  /home/pratyush/src/linux/Documentation/devicetree/bindings/spi/fsl,spi-fsl-dspi.example.dt.yaml: flash@0: 'fsl,spi-cs-sck-delay' does not match any of the regexes: '^partition@', 'pinctrl-[0-9]+'
     From schema: /home/pratyush/src/lin/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml

I am trying to solve a similar problem for the Cadence QSPI controller 
binding and I wonder what the best solution for this is. The obvious one 
would be to add these properties to jedec,spi-nor.yaml. I haven't 
managed to come up with any other solution to this problem.

Rob, all, any suggestions on how to best model this?

> 
>  .../bindings/spi/fsl,spi-fsl-dspi.yaml        | 131 ++++++++++++++++++
>  .../devicetree/bindings/spi/spi-fsl-dspi.txt  |  65 ---------
>  MAINTAINERS                                   |   2 +-
>  3 files changed, 132 insertions(+), 66 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/spi/fsl,spi-fsl-dspi.yaml
>  delete mode 100644 Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
> 
> diff --git a/Documentation/devicetree/bindings/spi/fsl,spi-fsl-dspi.yaml b/Documentation/devicetree/bindings/spi/fsl,spi-fsl-dspi.yaml
> new file mode 100644
> index 000000000000..15ffc83bdba6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/fsl,spi-fsl-dspi.yaml
> @@ -0,0 +1,131 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/fsl,spi-fsl-dspi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale DSPI Controller
> +
> +maintainers:
> +  - Vladimir Oltean <olteanv@gmail.com>
> +
> +allOf:
> +  - $ref: "spi-controller.yaml#"
> +
> +properties:
> +  compatible:
> +    oneOf:
> +      - enum:
> +          - fsl,vf610-dspi
> +          - fsl,ls1021a-v1.0-dspi
> +          - fsl,ls1028a-dspi
> +          - fsl,ls2085a-dspi
> +          - fsl,lx2160a-dspi
> +      - items:
> +          - enum:
> +              - fsl,ls1012a-dspi
> +              - fsl,ls1028a-dspi
> +              - fsl,ls1043a-dspi
> +              - fsl,ls1046a-dspi
> +              - fsl,ls1088a-dspi
> +          - const: fsl,ls1021a-v1.0-dspi
> +      - items:
> +          - enum:
> +              - fsl,ls2080a-dspi
> +              - fsl,lx2160a-dspi
> +          - const: fsl,ls2085a-dspi
> +
> +  reg:
> +    maxItems: 1
> +    description: Offset and length of registers
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: SoC dspi clock
> +
> +  clock-names:
> +    items:
> +      - const: dspi
> +
> +  pinctrl-names:
> +    minItems: 1
> +    items:
> +      - const: default
> +    description:
> +      Names for the pin configuration must be "default"
> +
> +  dmas:
> +    maxItems: 2
> +
> +  dma-names:
> +    items:
> +      - const: tx
> +      - const: rx
> +
> +  spi-num-chipselects:
> +    maxItems: 1
> +    description: Number of the chipselect signals
> +
> +  bus-num:
> +    items:
> +      - description: Slave chip chipselect signal number
> +
> +patternProperties:
> +  "@[0-9a-f]+":
> +    type: object
> +
> +    properties:
> +      fsl,spi-cs-sck-delay:
> +        description:
> +          Delay in nanoseconds between activating chip select and the start of
> +          clock signal, at the start of a transfer.
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +
> +      fsl,spi-sck-cs-delay:
> +        description:
> +          Delay in nanoseconds between stopping the clock signal and
> +          deactivating chip select, at the end of a transfer.
> +        $ref: /schemas/types.yaml#/definitions/uint32
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - clock-names
> +  - spi-num-chipselects
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/fsl,qoriq-clockgen.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +    soc {
> +        #address-cells = <2>;
> +        #size-cells = <2>;
> +
> +        spi@2100000 {
> +            compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +            reg = <0x0 0x2100000 0x0 0x10000>;
> +            interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
> +            clock-names = "dspi";
> +            clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(2)>;
> +            dmas = <&edma0 0 62>, <&edma0 0 60>;
> +            dma-names = "tx", "rx";
> +            spi-num-chipselects = <4>;
> +            little-endian;
> +
> +            flash@0 {
> +                compatible = "jedec,spi-nor";
> +                spi-max-frequency = <10000000>;
> +                reg = <0>;
> +            };
> +        };
> +    };
> diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
> deleted file mode 100644
> index 30a79da9c039..000000000000
> --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
> +++ /dev/null
> @@ -1,65 +0,0 @@
> -ARM Freescale DSPI controller
> -
> -Required properties:
> -- compatible : must be one of:
> -	"fsl,vf610-dspi",
> -	"fsl,ls1021a-v1.0-dspi",
> -	"fsl,ls1012a-dspi" (optionally followed by "fsl,ls1021a-v1.0-dspi"),
> -	"fsl,ls1028a-dspi",
> -	"fsl,ls1043a-dspi" (optionally followed by "fsl,ls1021a-v1.0-dspi"),
> -	"fsl,ls1046a-dspi" (optionally followed by "fsl,ls1021a-v1.0-dspi"),
> -	"fsl,ls1088a-dspi" (optionally followed by "fsl,ls1021a-v1.0-dspi"),
> -	"fsl,ls2080a-dspi" (optionally followed by "fsl,ls2085a-dspi"),
> -	"fsl,ls2085a-dspi",
> -	"fsl,lx2160a-dspi",
> -- reg : Offset and length of the register set for the device
> -- interrupts : Should contain SPI controller interrupt
> -- clocks: from common clock binding: handle to dspi clock.
> -- clock-names: from common clock binding: Shall be "dspi".
> -- pinctrl-0: pin control group to be used for this controller.
> -- pinctrl-names: must contain a "default" entry.
> -- spi-num-chipselects : the number of the chipselect signals.
> -
> -Optional property:
> -- big-endian: If present the dspi device's registers are implemented
> -  in big endian mode.
> -- bus-num : the slave chip chipselect signal number.
> -
> -Optional SPI slave node properties:
> -- fsl,spi-cs-sck-delay: a delay in nanoseconds between activating chip
> -  select and the start of clock signal, at the start of a transfer.
> -- fsl,spi-sck-cs-delay: a delay in nanoseconds between stopping the clock
> -  signal and deactivating chip select, at the end of a transfer.
> -
> -Example:
> -
> -dspi0@4002c000 {
> -	#address-cells = <1>;
> -	#size-cells = <0>;
> -	compatible = "fsl,vf610-dspi";
> -	reg = <0x4002c000 0x1000>;
> -	interrupts = <0 67 0x04>;
> -	clocks = <&clks VF610_CLK_DSPI0>;
> -	clock-names = "dspi";
> -	spi-num-chipselects = <5>;
> -	bus-num = <0>;
> -	pinctrl-names = "default";
> -	pinctrl-0 = <&pinctrl_dspi0_1>;
> -	big-endian;
> -
> -	sflash: at26df081a@0 {
> -		#address-cells = <1>;
> -		#size-cells = <1>;
> -		compatible = "atmel,at26df081a";
> -		spi-max-frequency = <16000000>;
> -		spi-cpol;
> -		spi-cpha;
> -		reg = <0>;
> -		linux,modalias = "m25p80";
> -		modal = "at26df081a";
> -		fsl,spi-cs-sck-delay = <100>;
> -		fsl,spi-sck-cs-delay = <50>;
> -	};
> -};
> -
> -
> diff --git a/MAINTAINERS b/MAINTAINERS
> index d92f85ca831d..e2c5b7367db9 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -7060,7 +7060,7 @@ FREESCALE DSPI DRIVER
>  M:	Vladimir Oltean <olteanv@gmail.com>
>  L:	linux-spi@vger.kernel.org
>  S:	Maintained
> -F:	Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
> +F:	Documentation/devicetree/bindings/spi/fsl,spi-fsl-dspi.yaml
>  F:	drivers/spi/spi-fsl-dspi.c
>  F:	include/linux/spi/spi-fsl-dspi.h
>  
> -- 
> 2.17.1
> 

-- 
Regards,
Pratyush Yadav
Texas Instruments Inc.

  reply	other threads:[~2021-03-15 18:31 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-03-15 12:15 [PATCH] dt-bindings: spi: Convert Freescale DSPI to json schema Kuldeep Singh
2021-03-15 18:30 ` Pratyush Yadav [this message]
2021-03-16  5:56   ` [EXT] " Kuldeep Singh
2021-03-16 17:45   ` Michael Walle
2021-03-16 18:06     ` Pratyush Yadav
2021-03-16 18:22       ` Michael Walle
2021-03-24 17:51         ` Rob Herring
2021-03-22 13:20   ` Pratyush Yadav
2021-03-24 18:10   ` Rob Herring
2021-03-15 20:54 ` Vladimir Oltean
2021-03-16  6:08   ` [EXT] " Kuldeep Singh
2021-03-16 10:15     ` Vladimir Oltean
2021-03-24 18:14       ` Rob Herring
2021-03-24 18:53         ` Vladimir Oltean
2021-03-24 19:20           ` Rob Herring
2021-03-25  1:06             ` Vladimir Oltean
2021-03-24 18:18 ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210315183051.ugvmz4zqrvuo6iqq@ti.com \
    --to=p.yadav@ti.com \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=kuldeep.singh@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=olteanv@gmail.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).