Linux-SPI Archive on lore.kernel.org
 help / color / Atom feed
From: Clark Wang <xiaoning.wang@nxp.com>
To: broonie@kernel.org, shawnguo@kernel.org, s.hauer@pengutronix.de,
	festevam@gmail.com
Cc: kernel@pengutronix.de, linux-imx@nxp.com,
	linux-spi@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH] spi: imx: add a check for speed_hz before calculating the clock
Date: Thu,  8 Apr 2021 18:33:47 +0800
Message-ID: <20210408103347.244313-2-xiaoning.wang@nxp.com> (raw)
In-Reply-To: <20210408103347.244313-1-xiaoning.wang@nxp.com>

When some drivers use spi to send data, spi_transfer->speed_hz is
not assigned. If spidev->max_speed_hz is not assigned as well, it
will cause an error in configuring the clock.
Add a check for these two values before configuring the clock. An
error will be returned when they are not assigned.

Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
---
 drivers/spi/spi-imx.c | 37 +++++++++++++++++++++----------------
 1 file changed, 21 insertions(+), 16 deletions(-)

diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index 24ba7ab1b05d..01f27b4d7384 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -66,8 +66,7 @@ struct spi_imx_data;
 struct spi_imx_devtype_data {
 	void (*intctrl)(struct spi_imx_data *, int);
 	int (*prepare_message)(struct spi_imx_data *, struct spi_message *);
-	int (*prepare_transfer)(struct spi_imx_data *, struct spi_device *,
-				struct spi_transfer *);
+	int (*prepare_transfer)(struct spi_imx_data *, struct spi_device *);
 	void (*trigger)(struct spi_imx_data *);
 	int (*rx_available)(struct spi_imx_data *);
 	void (*reset)(struct spi_imx_data *);
@@ -581,11 +580,10 @@ static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
 }
 
 static int mx51_ecspi_prepare_transfer(struct spi_imx_data *spi_imx,
-				       struct spi_device *spi,
-				       struct spi_transfer *t)
+				       struct spi_device *spi)
 {
 	u32 ctrl = readl(spi_imx->base + MX51_ECSPI_CTRL);
-	u32 clk = t->speed_hz, delay;
+	u32 clk, delay;
 
 	/* Clear BL field and set the right value */
 	ctrl &= ~MX51_ECSPI_CTRL_BL_MASK;
@@ -599,7 +597,7 @@ static int mx51_ecspi_prepare_transfer(struct spi_imx_data *spi_imx,
 	/* set clock speed */
 	ctrl &= ~(0xf << MX51_ECSPI_CTRL_POSTDIV_OFFSET |
 		  0xf << MX51_ECSPI_CTRL_PREDIV_OFFSET);
-	ctrl |= mx51_ecspi_clkdiv(spi_imx, t->speed_hz, &clk);
+	ctrl |= mx51_ecspi_clkdiv(spi_imx, spi_imx->spi_bus_clk, &clk);
 	spi_imx->spi_bus_clk = clk;
 
 	if (spi_imx->usedma)
@@ -711,13 +709,12 @@ static int mx31_prepare_message(struct spi_imx_data *spi_imx,
 }
 
 static int mx31_prepare_transfer(struct spi_imx_data *spi_imx,
-				 struct spi_device *spi,
-				 struct spi_transfer *t)
+				 struct spi_device *spi)
 {
 	unsigned int reg = MX31_CSPICTRL_ENABLE | MX31_CSPICTRL_MASTER;
 	unsigned int clk;
 
-	reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, t->speed_hz, &clk) <<
+	reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, spi_imx->spi_bus_clk, &clk) <<
 		MX31_CSPICTRL_DR_SHIFT;
 	spi_imx->spi_bus_clk = clk;
 
@@ -816,14 +813,13 @@ static int mx21_prepare_message(struct spi_imx_data *spi_imx,
 }
 
 static int mx21_prepare_transfer(struct spi_imx_data *spi_imx,
-				 struct spi_device *spi,
-				 struct spi_transfer *t)
+				 struct spi_device *spi)
 {
 	unsigned int reg = MX21_CSPICTRL_ENABLE | MX21_CSPICTRL_MASTER;
 	unsigned int max = is_imx27_cspi(spi_imx) ? 16 : 18;
 	unsigned int clk;
 
-	reg |= spi_imx_clkdiv_1(spi_imx->spi_clk, t->speed_hz, max, &clk)
+	reg |= spi_imx_clkdiv_1(spi_imx->spi_clk, spi_imx->spi_bus_clk, max, &clk)
 		<< MX21_CSPICTRL_DR_SHIFT;
 	spi_imx->spi_bus_clk = clk;
 
@@ -892,13 +888,12 @@ static int mx1_prepare_message(struct spi_imx_data *spi_imx,
 }
 
 static int mx1_prepare_transfer(struct spi_imx_data *spi_imx,
-				struct spi_device *spi,
-				struct spi_transfer *t)
+				struct spi_device *spi)
 {
 	unsigned int reg = MX1_CSPICTRL_ENABLE | MX1_CSPICTRL_MASTER;
 	unsigned int clk;
 
-	reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, t->speed_hz, &clk) <<
+	reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, spi_imx->spi_bus_clk, &clk) <<
 		MX1_CSPICTRL_DR_SHIFT;
 	spi_imx->spi_bus_clk = clk;
 
@@ -1177,6 +1172,16 @@ static int spi_imx_setupxfer(struct spi_device *spi,
 	if (!t)
 		return 0;
 
+	if (!t->speed_hz) {
+		if (!spi->max_speed_hz) {
+			dev_err(&spi->dev, "no speed_hz provided!\n");
+			return -EINVAL;
+		}
+		dev_dbg(&spi->dev, "using spi->max_speed_hz!\n");
+		spi_imx->spi_bus_clk = spi->max_speed_hz;
+	} else
+		spi_imx->spi_bus_clk = t->speed_hz;
+
 	spi_imx->bits_per_word = t->bits_per_word;
 
 	/*
@@ -1218,7 +1223,7 @@ static int spi_imx_setupxfer(struct spi_device *spi,
 		spi_imx->slave_burst = t->len;
 	}
 
-	spi_imx->devtype_data->prepare_transfer(spi_imx, spi, t);
+	spi_imx->devtype_data->prepare_transfer(spi_imx, spi);
 
 	return 0;
 }
-- 
2.25.1


  reply index

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-04-08 10:33 [PATCH] spi: imx: add 16/32 bits per word support for slave mode Clark Wang
2021-04-08 10:33 ` Clark Wang [this message]
2021-04-08 13:43   ` [PATCH] spi: imx: add a check for speed_hz before calculating the clock Mark Brown
2021-04-08 14:05   ` Mark Brown
2021-04-09 16:22   ` Mark Brown
2021-05-24  8:25 ` [PATCH] spi: imx: add 16/32 bits per word support for slave mode Tomas Melin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210408103347.244313-2-xiaoning.wang@nxp.com \
    --to=xiaoning.wang@nxp.com \
    --cc=broonie@kernel.org \
    --cc=festevam@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-SPI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-spi/0 linux-spi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-spi linux-spi/ https://lore.kernel.org/linux-spi \
		linux-spi@vger.kernel.org
	public-inbox-index linux-spi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-spi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git