linux-staging.lists.linux.dev archive mirror
 help / color / mirror / Atom feed
From: Martin Kaiser <martin@kaiser.cx>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-staging@lists.linux.dev, kernel-janitors@vger.kernel.org,
	linux-kernel@vger.kernel.org, Martin Kaiser <martin@kaiser.cx>
Subject: [PATCH 12/13] staging: rtl8188eu: remove sdio defines
Date: Sun, 20 Jun 2021 19:53:00 +0200	[thread overview]
Message-ID: <20210620175301.14988-12-martin@kaiser.cx> (raw)
In-Reply-To: <20210620175301.14988-1-martin@kaiser.cx>

Remove sdio defines which are not used by this driver.

Signed-off-by: Martin Kaiser <martin@kaiser.cx>
---
 .../staging/rtl8188eu/include/rtl8188e_spec.h | 136 ------------------
 1 file changed, 136 deletions(-)

diff --git a/drivers/staging/rtl8188eu/include/rtl8188e_spec.h b/drivers/staging/rtl8188eu/include/rtl8188e_spec.h
index 55cce1f6bd77..94baea8bc068 100644
--- a/drivers/staging/rtl8188eu/include/rtl8188e_spec.h
+++ b/drivers/staging/rtl8188eu/include/rtl8188e_spec.h
@@ -1089,142 +1089,6 @@ So the following defines for 92C is not entire!!!!!!
 #define SCR_TXBCUSEDK		BIT(6)	/* Force Tx Bcast pkt Use Default Key */
 #define SCR_RXBCUSEDK		BIT(7)	/* Force Rx Bcast pkt Use Default Key */
 
-/*	RTL8188E SDIO Configuration */
-
-/*  I/O bus domain address mapping */
-#define SDIO_LOCAL_BASE			0x10250000
-#define WLAN_IOREG_BASE			0x10260000
-#define FIRMWARE_FIFO_BASE		0x10270000
-#define TX_HIQ_BASE			0x10310000
-#define TX_MIQ_BASE			0x10320000
-#define TX_LOQ_BASE			0x10330000
-#define RX_RX0FF_BASE			0x10340000
-
-/*  SDIO host local register space mapping. */
-#define SDIO_LOCAL_MSK			0x0FFF
-#define WLAN_IOREG_MSK			0x7FFF
-#define WLAN_FIFO_MSK			0x1FFF	/*  Aggregation Length[12:0] */
-#define WLAN_RX0FF_MSK			0x0003
-
-/*  Without ref to the SDIO Device ID */
-#define SDIO_WITHOUT_REF_DEVICE_ID	0
-#define SDIO_LOCAL_DEVICE_ID		0	/*  0b[16], 000b[15:13] */
-#define WLAN_TX_HIQ_DEVICE_ID		4	/*  0b[16], 100b[15:13] */
-#define WLAN_TX_MIQ_DEVICE_ID		5	/*  0b[16], 101b[15:13] */
-#define WLAN_TX_LOQ_DEVICE_ID		6	/*  0b[16], 110b[15:13] */
-#define WLAN_RX0FF_DEVICE_ID		7	/*  0b[16], 111b[15:13] */
-#define WLAN_IOREG_DEVICE_ID		8	/*  1b[16] */
-
-/*  SDIO Tx Free Page Index */
-#define HI_QUEUE_IDX			0
-#define MID_QUEUE_IDX			1
-#define LOW_QUEUE_IDX			2
-#define PUBLIC_QUEUE_IDX		3
-
-#define SDIO_MAX_TX_QUEUE		3	/*  HIQ, MIQ and LOQ */
-#define SDIO_MAX_RX_QUEUE		1
-
-/*  SDIO Tx Control */
-#define SDIO_REG_TX_CTRL		0x0000
-/*  SDIO Host Interrupt Mask */
-#define SDIO_REG_HIMR			0x0014
-/*  SDIO Host Interrupt Service Routine */
-#define SDIO_REG_HISR			0x0018
-/*  HCI Current Power Mode */
-#define SDIO_REG_HCPWM			0x0019
-/*  RXDMA Request Length */
-#define SDIO_REG_RX0_REQ_LEN		0x001C
-/*  Free Tx Buffer Page */
-#define SDIO_REG_FREE_TXPG		0x0020
-/*  HCI Current Power Mode 1 */
-#define SDIO_REG_HCPWM1			0x0024
-/*  HCI Current Power Mode 2 */
-#define SDIO_REG_HCPWM2			0x0026
-/*  HTSF Informaion */
-#define SDIO_REG_HTSFR_INFO		0x0030
-/*  HCI Request Power Mode 1 */
-#define SDIO_REG_HRPWM1			0x0080
-/*  HCI Request Power Mode 2 */
-#define SDIO_REG_HRPWM2			0x0082
-/*  HCI Power Save Clock */
-#define SDIO_REG_HPS_CLKR		0x0084
-/*  SDIO HCI Suspend Control */
-#define SDIO_REG_HSUS_CTRL		0x0086
-/*  SDIO Host Extension Interrupt Mask Always */
-#define SDIO_REG_HIMR_ON		0x0090
-/*  SDIO Host Extension Interrupt Status Always */
-#define SDIO_REG_HISR_ON		0x0091
-
-#define SDIO_HIMR_DISABLED			0
-
-/*  RTL8188E SDIO Host Interrupt Mask Register */
-#define SDIO_HIMR_RX_REQUEST_MSK		BIT(0)
-#define SDIO_HIMR_AVAL_MSK			BIT(1)
-#define SDIO_HIMR_TXERR_MSK			BIT(2)
-#define SDIO_HIMR_RXERR_MSK			BIT(3)
-#define SDIO_HIMR_TXFOVW_MSK			BIT(4)
-#define SDIO_HIMR_RXFOVW_MSK			BIT(5)
-#define SDIO_HIMR_TXBCNOK_MSK			BIT(6)
-#define SDIO_HIMR_TXBCNERR_MSK			BIT(7)
-#define SDIO_HIMR_BCNERLY_INT_MSK		BIT(16)
-#define SDIO_HIMR_C2HCMD_MSK			BIT(17)
-#define SDIO_HIMR_CPWM1_MSK			BIT(18)
-#define SDIO_HIMR_CPWM2_MSK			BIT(19)
-#define SDIO_HIMR_HSISR_IND_MSK			BIT(20)
-#define SDIO_HIMR_GTINT3_IND_MSK		BIT(21)
-#define SDIO_HIMR_GTINT4_IND_MSK		BIT(22)
-#define SDIO_HIMR_PSTIMEOUT_MSK			BIT(23)
-#define SDIO_HIMR_OCPINT_MSK			BIT(24)
-#define SDIO_HIMR_ATIMEND_MSK			BIT(25)
-#define SDIO_HIMR_ATIMEND_E_MSK			BIT(26)
-#define SDIO_HIMR_CTWEND_MSK			BIT(27)
-
-/* RTL8188E SDIO Specific */
-#define	SDIO_HIMR_MCU_ERR_MSK			BIT(28)
-#define	SDIO_HIMR_TSF_BIT32_TOGGLE_MSK		BIT(29)
-
-/*  SDIO Host Interrupt Service Routine */
-#define SDIO_HISR_RX_REQUEST			BIT(0)
-#define SDIO_HISR_AVAL				BIT(1)
-#define SDIO_HISR_TXERR				BIT(2)
-#define SDIO_HISR_RXERR				BIT(3)
-#define SDIO_HISR_TXFOVW			BIT(4)
-#define SDIO_HISR_RXFOVW			BIT(5)
-#define SDIO_HISR_TXBCNOK			BIT(6)
-#define SDIO_HISR_TXBCNERR			BIT(7)
-#define SDIO_HISR_BCNERLY_INT			BIT(16)
-#define SDIO_HISR_C2HCMD			BIT(17)
-#define SDIO_HISR_CPWM1				BIT(18)
-#define SDIO_HISR_CPWM2				BIT(19)
-#define SDIO_HISR_HSISR_IND			BIT(20)
-#define SDIO_HISR_GTINT3_IND			BIT(21)
-#define SDIO_HISR_GTINT4_IND			BIT(22)
-#define SDIO_HISR_PSTIME			BIT(23)
-#define SDIO_HISR_OCPINT			BIT(24)
-#define SDIO_HISR_ATIMEND			BIT(25)
-#define SDIO_HISR_ATIMEND_E			BIT(26)
-#define SDIO_HISR_CTWEND			BIT(27)
-
-/* RTL8188E SDIO Specific */
-#define	SDIO_HISR_MCU_ERR			BIT(28)
-#define	SDIO_HISR_TSF_BIT32_TOGGLE		BIT(29)
-
-#define MASK_SDIO_HISR_CLEAR				\
-	(SDIO_HISR_TXERR | SDIO_HISR_RXERR | SDIO_HISR_TXFOVW |\
-	 SDIO_HISR_RXFOVW | SDIO_HISR_TXBCNOK | SDIO_HISR_TXBCNERR |\
-	 SDIO_HISR_C2HCMD | SDIO_HISR_CPWM1 | SDIO_HISR_CPWM2 |\
-	 SDIO_HISR_HSISR_IND | SDIO_HISR_GTINT3_IND | SDIO_HISR_GTINT4_IND |\
-	 SDIO_HISR_PSTIMEOUT | SDIO_HISR_OCPINT)
-
-/*  SDIO HCI Suspend Control Register */
-#define HCI_RESUME_PWR_RDY		BIT(1)
-#define HCI_SUS_CTRL			BIT(0)
-
-/*  SDIO Tx FIFO related */
-/*  The number of Tx FIFO free page */
-#define SDIO_TX_FREE_PG_QUEUE			4
-#define SDIO_TX_FIFO_PAGE_SZ			128
-
 /*	0xFE00h ~ 0xFE55h	USB Configuration */
 
 /* 2 USB Information (0xFE17) */
-- 
2.20.1


  parent reply	other threads:[~2021-06-20 17:53 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-20 17:52 [PATCH 01/13] staging: rtl8188eu: handle errors from dev_alloc_name Martin Kaiser
2021-06-20 17:52 ` [PATCH 02/13] staging: rtl8188eu: remove RT_TRACE prints from usb_intf.c Martin Kaiser
2021-06-20 17:52 ` [PATCH 03/13] staging: rtl8188eu: remove RT_TRACE prints from rtl8188e_hal_init.c Martin Kaiser
2021-06-20 17:52 ` [PATCH 04/13] staging: rtl8188eu: remove a couple of unused defines Martin Kaiser
2021-06-20 17:52 ` [PATCH 05/13] staging: rtl8188eu: remove efuse type Martin Kaiser
2021-06-20 17:52 ` [PATCH 06/13] staging: rtl8188eu: remove unnecessary if clause Martin Kaiser
2021-06-20 17:52 ` [PATCH 07/13] staging: rtl8188eu: remove RT_TRACE and MSG_88E prints from usb_halinit.c Martin Kaiser
2021-06-20 17:52 ` [PATCH 08/13] staging: rtl8188eu: remove HAL_INIT_PROFILE_TAG Martin Kaiser
2021-06-20 17:52 ` [PATCH 09/13] staging: rtl8188eu: simplify rtl88eu_mon_init Martin Kaiser
2021-06-20 17:52 ` [PATCH 10/13] staging: rtl8188eu: remove RT_TRACE prints from pwrseqcmd.c Martin Kaiser
2021-06-20 17:52 ` [PATCH 11/13] staging: rtl8188eu: make efuse_ReadEFuse static Martin Kaiser
2021-06-20 17:53 ` Martin Kaiser [this message]
2021-06-20 17:53 ` [PATCH 13/13] staging: rtl8188eu: remove more unused defines Martin Kaiser

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210620175301.14988-12-martin@kaiser.cx \
    --to=martin@kaiser.cx \
    --cc=gregkh@linuxfoundation.org \
    --cc=kernel-janitors@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-staging@lists.linux.dev \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).