linux-sunxi.lists.linux.dev archive mirror
 help / color / mirror / Atom feed
From: Andre Przywara <andre.przywara@arm.com>
To: Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
	Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Rob Herring <robh@kernel.org>, Icenowy Zheng <icenowy@aosc.io>,
	Samuel Holland <samuel@sholland.org>,
	Ondrej Jirman <megous@megous.com>,
	linux-arm-kernel@lists.infradead.org,
	linux-sunxi@googlegroups.com, linux-sunxi@lists.linux.dev,
	linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH v6 16/17] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support
Date: Wed, 19 May 2021 11:41:51 +0100	[thread overview]
Message-ID: <20210519104152.21119-17-andre.przywara@arm.com> (raw)
In-Reply-To: <20210519104152.21119-1-andre.przywara@arm.com>

The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
  - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
  - 512MiB/1GiB DDR3 DRAM
  - AXP305 PMIC
  - Raspberry-Pi-1 compatible GPIO header
  - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
  - 1 USB 2.0 host port
  - 1 USB 2.0 type C port (power supply + OTG)
  - MicroSD slot
  - on-board 2MiB bootable SPI NOR flash
  - 1Gbps Ethernet port (via RTL8211F PHY)
  - micro-HDMI port
  - unsupported Allwinner WiFi/BT chip

For more details see: https://linux-sunxi.org/Orange_Pi_Zero_2

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 245 ++++++++++++++++++
 2 files changed, 246 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 41ce680e5f8d..9ba4b5d92657 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -36,3 +36,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
new file mode 100644
index 000000000000..a26201288872
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -0,0 +1,245 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "OrangePi Zero2";
+	compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
+
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_usb1_vbus: usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_vcc5v>;
+		enable-active-high;
+		gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+		status = "okay";
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dcdce>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic@745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			reg_aldo2: aldo2 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+			};
+
+			reg_aldo3: aldo3 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			bldo2 {
+				/* unused */
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				/* reserved */
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1080000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&spi0  {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usbotg {
+	/*
+	 * PHY0 pins are connected to a USB-C socket, but a role switch
+	 * is not implemented: both CC pins are pulled to GND.
+	 * The VBUS pins power the device, so a fixed peripheral mode
+	 * is the best choice.
+	 * The board can be powered via GPIOs, in this case port0 *can*
+	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
+	 * then provided by the GPIOs. Any user of this setup would
+	 * need to adjust the DT accordingly: dr_mode set to "host",
+	 * enabling OHCI0 and EHCI0.
+	 */
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
-- 
2.17.5


  parent reply	other threads:[~2021-05-19 10:42 UTC|newest]

Thread overview: 45+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-05-19 10:41 [PATCH v6 00/17] arm64: sunxi: Initial Allwinner H616 SoC support Andre Przywara
2021-05-19 10:41 ` [PATCH v6 01/17] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ) Andre Przywara
2021-05-21  1:39   ` Rob Herring
2021-05-22 14:46   ` Samuel Holland
2021-05-23  0:01     ` Andre Przywara
2021-05-19 10:41 ` [PATCH v6 02/17] mfd: axp20x: Allow AXP 806 chips without interrupt lines Andre Przywara
2021-05-19 15:01   ` Lee Jones
2021-05-19 10:41 ` [PATCH v6 03/17] dt-bindings: rtc: sun6i: Add H616 compatible string Andre Przywara
2021-05-21  1:39   ` Rob Herring
2021-05-21  2:37   ` Samuel Holland
2021-06-07 12:59     ` Andre Przywara
2021-06-08  4:23       ` Samuel Holland
2021-06-15 12:24         ` Andre Przywara
2021-06-16  9:07           ` Maxime Ripard
2021-06-16 11:28             ` Andre Przywara
2021-05-19 10:41 ` [PATCH v6 04/17] rtc: sun6i: Add support for linear day storage Andre Przywara
2021-05-22  7:26   ` Jernej Škrabec
2021-05-19 10:41 ` [PATCH v6 05/17] rtc: sun6i: Add Allwinner H616 support Andre Przywara
2021-05-22  7:29   ` Jernej Škrabec
2021-05-23  0:06     ` Andre Przywara
2021-05-19 10:41 ` [PATCH v6 06/17] dt-bindings: net: sun8i-emac: Add H616 compatible string Andre Przywara
2021-05-21  1:40   ` Rob Herring
2021-05-19 10:41 ` [PATCH v6 07/17] net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register Andre Przywara
2021-05-19 10:41 ` [PATCH v6 08/17] dt-bindings: usb: Add H616 compatible string Andre Przywara
2021-05-21  1:40   ` Rob Herring
2021-05-19 10:41 ` [PATCH v6 09/17] dt-bindings: usb: sunxi-musb: " Andre Przywara
2021-05-21  1:40   ` Rob Herring
2021-05-19 10:41 ` [PATCH v6 10/17] phy: sun4i-usb: Rework HCI PHY (aka. "pmu_unk1") handling Andre Przywara
2021-05-19 10:41 ` [PATCH v6 11/17] phy: sun4i-usb: Allow reset line to be shared Andre Przywara
2021-05-19 10:41 ` [PATCH v6 12/17] phy: sun4i-usb: Introduce port2 SIDDQ quirk Andre Przywara
2021-05-24 11:59   ` Maxime Ripard
2021-05-24 12:51     ` Jernej Škrabec
2021-05-25 11:29     ` Andre Przywara
2021-06-07 13:22       ` Maxime Ripard
2021-06-07 14:17         ` Andre Przywara
2021-06-07 14:26           ` [linux-sunxi] " Chen-Yu Tsai
2021-06-14  0:20             ` Andre Przywara
2021-05-19 10:41 ` [PATCH v6 13/17] phy: sun4i-usb: Add support for the H616 USB PHY Andre Przywara
2021-05-19 10:41 ` [PATCH v6 14/17] arm64: dts: allwinner: Add Allwinner H616 .dtsi file Andre Przywara
2021-05-24 12:02   ` Maxime Ripard
2021-06-07 12:59     ` Andre Przywara
2021-05-19 10:41 ` [PATCH v6 15/17] dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding Andre Przywara
2021-05-19 10:41 ` Andre Przywara [this message]
2021-05-19 10:41 ` [PATCH v6 17/17] arm64: dts: allwinner: h616: Add X96 Mate TV box support Andre Przywara
2021-05-22  7:32   ` Jernej Škrabec

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210519104152.21119-17-andre.przywara@arm.com \
    --to=andre.przywara@arm.com \
    --cc=devicetree@vger.kernel.org \
    --cc=icenowy@aosc.io \
    --cc=jernej.skrabec@gmail.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-sunxi@googlegroups.com \
    --cc=linux-sunxi@lists.linux.dev \
    --cc=megous@megous.com \
    --cc=mripard@kernel.org \
    --cc=robh@kernel.org \
    --cc=samuel@sholland.org \
    --cc=wens@csie.org \
    --subject='Re: [PATCH v6 16/17] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).