[RESEND v2 1/2] dt-bindings: usb: Convert SMSC USB3503 binding to a schema

[RESEND v2 1/2] dt-bindings: usb: Convert SMSC USB3503 binding to a schema

[Maxime Ripard]

The SMSC USB3503 USB Hub Controller is supported by Linux thanks to
its device tree binding.

Now that we have the DT validation in place, let's convert the device
tree bindings for that driver over to a YAML schema.

Cc: Dongjin Kim <tobetter@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>

---

Changes from v1:
  - Added maximum number of items for clocks and gpios
  - Fixed the example node name
---
 .../devicetree/bindings/usb/smsc,usb3503.yaml | 108 ++++++++++++++++++
 .../devicetree/bindings/usb/usb3503.txt       |  39 -------
 2 files changed, 108 insertions(+), 39 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/usb/smsc,usb3503.yaml
 delete mode 100644 Documentation/devicetree/bindings/usb/usb3503.txt

diff --git a/Documentation/devicetree/bindings/usb/smsc,usb3503.yaml b/Documentation/devicetree/bindings/usb/smsc,usb3503.yaml
new file mode 100644
index 000000000000..39228a506b93
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/smsc,usb3503.yaml
@@ -0,0 +1,108 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/smsc,usb3503.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SMSC USB3503 High-Speed Hub Controller Device Tree Bindings
+
+maintainers:
+  - Dongjin Kim <tobetter@gmail.com>
+
+properties:
+  compatible:
+    enum:
+      - smsc,usb3503
+      - smsc,usb3503a
+
+  reg:
+    maxItems: 1
+
+  connect-gpios:
+    maxItems: 1
+    description: >
+      GPIO for connect
+
+  intn-gpios:
+    maxItems: 1
+    description: >
+      GPIO for interrupt
+
+  reset-gpios:
+    maxItems: 1
+    description: >
+      GPIO for reset
+
+  disabled-ports:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    maxItems: 3
+    items:
+      minimum: 1
+      maximum: 3
+    description: >
+      Specifies the ports unused using their port number. Do not describe this
+      property if all ports have to be enabled.
+
+  initial-mode:
+    enum: [1, 2]
+    description: >
+      Specifies initial mode. 1 for Hub mode, 2 for standby mode.
+
+  clocks:
+    maxItems: 1
+    description: >
+      Clock used for driving REFCLK signal. If not provided the driver assumes
+      that clock signal is always available, its rate is specified by REF_SEL
+      pins and a value from the primary reference clock frequencies table is
+      used.
+
+  clock-names:
+    const: refclk
+
+  refclk-frequency:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: >
+      Frequency of the REFCLK signal as defined by REF_SEL pins. If not
+      provided, driver will not set rate of the REFCLK signal and assume that a
+      value from the primary reference clock frequencies table is used.
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+      i2c {
+          #address-cells = <1>;
+          #size-cells = <0>;
+        
+          usb-hub@8 {
+              compatible = "smsc,usb3503";
+              reg = <0x08>;
+              connect-gpios = <&gpx3 0 1>;
+              disabled-ports = <2 3>;
+              intn-gpios = <&gpx3 4 1>;
+              reset-gpios = <&gpx3 5 1>;
+              initial-mode = <1>;
+              clocks = <&clks 80>;
+              clock-names = "refclk";
+          };
+      };
+
+  - |
+      #include <dt-bindings/gpio/gpio.h>
+
+      usb-hub {
+          /* I2C is not connected */
+          compatible = "smsc,usb3503";
+          initial-mode = <1>; /* initialize in HUB mode */
+          disabled-ports = <1>;
+          intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+          reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
+          connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+          refclk-frequency = <19200000>;
+      };
+
+...
diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt
deleted file mode 100644
index 057dd384d473..000000000000
--- a/Documentation/devicetree/bindings/usb/usb3503.txt
+++ /dev/null
@@ -1,39 +0,0 @@
-SMSC USB3503 High-Speed Hub Controller
-
-Required properties:
-- compatible: Should be "smsc,usb3503" or "smsc,usb3503a".
-
-Optional properties:
-- reg: Specifies the i2c slave address, it is required and should be 0x08
-       if I2C is used.
-- connect-gpios: Should specify GPIO for connect.
-- disabled-ports: Should specify the ports unused.
-	'1' or '2' or '3' are available for this property to describe the port
-	number. 1~3 property values are possible to be described.
-	Do not describe this property if all ports have to be enabled.
-- intn-gpios: Should specify GPIO for interrupt.
-- reset-gpios: Should specify GPIO for reset.
-- initial-mode: Should specify initial mode.
-                (1 for HUB mode, 2 for STANDBY mode)
-- refclk: Clock used for driving REFCLK signal (optional, if not provided
-	the driver assumes that clock signal is always available, its
-	rate is specified by REF_SEL pins and a value from the primary
-	reference clock frequencies table is used). Use clocks and
-	clock-names in order to assign it
-- refclk-frequency: Frequency of the REFCLK signal as defined by REF_SEL
-	pins (optional, if not provided, driver will not set rate of the
-	REFCLK signal and assume that a value from the primary reference
-	clock frequencies table is used)
-
-Examples:
-	usb3503@8 {
-		compatible = "smsc,usb3503";
-		reg = <0x08>;
-		connect-gpios = <&gpx3 0 1>;
-		disabled-ports = <2 3>;
-		intn-gpios = <&gpx3 4 1>;
-		reset-gpios = <&gpx3 5 1>;
-		initial-mode = <1>;
-		clocks = <&clks 80>;
-		clock-names = "refclk";
-	};
-- 
2.31.1

[RESEND v2 2/2] dt-bindings: usb: dwc3: Fix usb-phy check

[Maxime Ripard]

The original binding was allowing any combination of usb2-phy and
usb3-phy in the phys and phy-names properties.

However, the current binding enforces that those properties must be a
list of usb2-phy and usb3-phy, with exactly one element, effectively
making usb2-phy the only value being valid.

Let's rework the properties description to allow either one or two
element picked with values either usb2-phy or usb3-phy. The rest of the
tooling makes sure that we don't get any duplicate value, so this should
be what we want.

Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
---
 Documentation/devicetree/bindings/usb/snps,dwc3.yaml | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
index 1040d06cc0d7..25ac2c93dc6c 100644
--- a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
+++ b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
@@ -73,15 +73,15 @@ properties:
 
   phys:
     minItems: 1
-    items:
-      - description: USB2/HS PHY
-      - description: USB3/SS PHY
+    maxItems: 2
 
   phy-names:
     minItems: 1
+    maxItems: 2
     items:
-      - const: usb2-phy
-      - const: usb3-phy
+      enum:
+        - usb2-phy
+        - usb3-phy
 
   resets:
     minItems: 1
-- 
2.31.1