ARM Sunxi Platform Development
 help / color / Atom feed
* [PATCH 0/3] sunxi: H616: SPI boot support
@ 2021-07-05 23:04 Andre Przywara
  2021-07-05 23:04 ` [PATCH 1/3] sunxi: SPL SPI: Allow larger SPL Andre Przywara
                   ` (2 more replies)
  0 siblings, 3 replies; 7+ messages in thread
From: Andre Przywara @ 2021-07-05 23:04 UTC (permalink / raw)
  To: Jagan Teki; +Cc: Samuel Holland, Jernej Skrabec, u-boot, linux-sunxi

The Allwinner H616 supports booting from SPI NOR flash, for which we
use our SPL specific SPI driver. Since this uses hardcoded values for
clocks, resets and pins, we need to extend it to cover the H616 SoC
as well.

Patch 1/3 extends the logic that determines the offset of the U-Boot
payload, from a fixed value to actually observing the SPL size.
Patch 2/3 piggy backs on the existing H6 SPI boot support, to cover
the (very similar) H616 as well. The only actual difference between the
two is one pin configuration.
Patch 3/3 enables SPI boot for the OrangePi Zero 2 board, which comes
with a 2MiB SPI flash chip soldered.

In my experiments I couldn't actually convince the BROM to load the SPL,
it always fell through to FEL mode. I post this series anyway, because:
1) We will need this code in any case, since it loads the rest of U-Boot
   (and TF-A) from SPI flash. By hacking sunxi-fel I could verify that
   this part works: the SPL code detected "SPI boot" and booted the rest
   of the firmware successfully from SPI flash.
2) I would encourage other people to try this, maybe it's just my board
   that is broken? (I dimly remember booting something some months ago.)
   The easiest way to flash U-Boot is via sunxi-fel:
   $ sunxi-fel -v -p spiflash-write 0 u-boot-sunxi-with-spl.bin

Cheers,
Andre

Andre Przywara (3):
  sunxi: SPL SPI: Allow larger SPL
  sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC
  sunxi: OrangePi Zero 2: Enable SPI booting

 arch/arm/mach-sunxi/Kconfig         |  2 +-
 arch/arm/mach-sunxi/spl_spi_sunxi.c | 37 +++++++++++++++++------------
 configs/orangepi_zero2_defconfig    |  1 +
 3 files changed, 24 insertions(+), 16 deletions(-)

-- 
2.17.5


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH 1/3] sunxi: SPL SPI: Allow larger SPL
  2021-07-05 23:04 [PATCH 0/3] sunxi: H616: SPI boot support Andre Przywara
@ 2021-07-05 23:04 ` Andre Przywara
  2021-07-06 14:22   ` Jagan Teki
  2021-07-05 23:04 ` [PATCH 2/3] sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC Andre Przywara
  2021-07-05 23:04 ` [PATCH 3/3] sunxi: OrangePi Zero 2: Enable SPI booting Andre Przywara
  2 siblings, 1 reply; 7+ messages in thread
From: Andre Przywara @ 2021-07-05 23:04 UTC (permalink / raw)
  To: Jagan Teki; +Cc: Samuel Holland, Jernej Skrabec, u-boot, linux-sunxi

The more recent Allwinner SoCs BootROMs can actually load SPL images
larger than 32KB. We use this on the H616 to fit the extra code needed
for the PMIC into the image, and have provisions in board.c to respect
that larger SPL size when booting from MMC.

However the sunxi SPL SPI loader has a hardcoded load offset of 32KB,
which will fail on the H616.

To fix this, use the same algorithm we use for MMC: if the SPL size is
smaller than 32KB, we use 32KB, otherwise we expect the U-Boot payload
directly after the SPL code.

This prepares for SPI booting with larger SPLs like on the H616.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm/mach-sunxi/spl_spi_sunxi.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-sunxi/spl_spi_sunxi.c b/arch/arm/mach-sunxi/spl_spi_sunxi.c
index 15e86cbac8f..3499c4cc5f8 100644
--- a/arch/arm/mach-sunxi/spl_spi_sunxi.c
+++ b/arch/arm/mach-sunxi/spl_spi_sunxi.c
@@ -7,6 +7,7 @@
 #include <image.h>
 #include <log.h>
 #include <spl.h>
+#include <asm/arch/spl.h>
 #include <asm/gpio.h>
 #include <asm/io.h>
 #include <linux/bitops.h>
@@ -326,10 +327,13 @@ static int spl_spi_load_image(struct spl_image_info *spl_image,
 	int ret = 0;
 	struct image_header *header;
 	header = (struct image_header *)(CONFIG_SYS_TEXT_BASE);
+	int load_offset = readl(SPL_ADDR + 0x10);
+
+	load_offset = max(load_offset, CONFIG_SYS_SPI_U_BOOT_OFFS);
 
 	spi0_init();
 
-	spi0_read_data((void *)header, CONFIG_SYS_SPI_U_BOOT_OFFS, 0x40);
+	spi0_read_data((void *)header, load_offset, 0x40);
 
         if (IS_ENABLED(CONFIG_SPL_LOAD_FIT) &&
 		image_get_magic(header) == FDT_MAGIC) {
@@ -342,14 +346,14 @@ static int spl_spi_load_image(struct spl_image_info *spl_image,
 		load.bl_len = 1;
 		load.read = spi_load_read;
 		ret = spl_load_simple_fit(spl_image, &load,
-					  CONFIG_SYS_SPI_U_BOOT_OFFS, header);
+					  load_offset, header);
 	} else {
 		ret = spl_parse_image_header(spl_image, header);
 		if (ret)
 			return ret;
 
 		spi0_read_data((void *)spl_image->load_addr,
-			       CONFIG_SYS_SPI_U_BOOT_OFFS, spl_image->size);
+			       load_offset, spl_image->size);
 	}
 
 	spi0_deinit();
-- 
2.17.5


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH 2/3] sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC
  2021-07-05 23:04 [PATCH 0/3] sunxi: H616: SPI boot support Andre Przywara
  2021-07-05 23:04 ` [PATCH 1/3] sunxi: SPL SPI: Allow larger SPL Andre Przywara
@ 2021-07-05 23:04 ` Andre Przywara
  2021-07-06 14:22   ` Jagan Teki
  2021-07-05 23:04 ` [PATCH 3/3] sunxi: OrangePi Zero 2: Enable SPI booting Andre Przywara
  2 siblings, 1 reply; 7+ messages in thread
From: Andre Przywara @ 2021-07-05 23:04 UTC (permalink / raw)
  To: Jagan Teki; +Cc: Samuel Holland, Jernej Skrabec, u-boot, linux-sunxi

The H616 SoC uses the same SPI IP as the H6, also shares the same clocks
and reset bits.
The only real difference is a slight change in the pin assignment: the
H6 uses PC5, the H616 PC4 instead. This makes for a small change in
our spi0_pinmux_setup() routine.

Apart from that, just extend the H6 #ifdef guards to also cover the H616,
using the shared CONFIG_SUN50I_GEN_H6 symbol.
Also use this symbol for the Kconfig dependency.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm/mach-sunxi/Kconfig         |  2 +-
 arch/arm/mach-sunxi/spl_spi_sunxi.c | 27 +++++++++++++++------------
 2 files changed, 16 insertions(+), 13 deletions(-)

diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index 49f94f095c1..6b9bbed9a7a 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -1057,7 +1057,7 @@ config SPL_STACK_R_ADDR
 
 config SPL_SPI_SUNXI
 	bool "Support for SPI Flash on Allwinner SoCs in SPL"
-	depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_R40 || MACH_SUN50I_H6
+	depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_R40 || SUN50I_GEN_H6
 	help
 	  Enable support for SPI Flash. This option allows SPL to read from
 	  sunxi SPI Flash. It uses the same method as the boot ROM, so does
diff --git a/arch/arm/mach-sunxi/spl_spi_sunxi.c b/arch/arm/mach-sunxi/spl_spi_sunxi.c
index 3499c4cc5f8..d00c34708be 100644
--- a/arch/arm/mach-sunxi/spl_spi_sunxi.c
+++ b/arch/arm/mach-sunxi/spl_spi_sunxi.c
@@ -78,7 +78,7 @@
 
 #define CCM_AHB_GATING0             (0x01C20000 + 0x60)
 #define CCM_H6_SPI_BGR_REG          (0x03001000 + 0x96c)
-#ifdef CONFIG_MACH_SUN50I_H6
+#ifdef CONFIG_SUN50I_GEN_H6
 #define CCM_SPI0_CLK                (0x03001000 + 0x940)
 #else
 #define CCM_SPI0_CLK                (0x01C20000 + 0xA0)
@@ -96,7 +96,7 @@
 /*
  * Allwinner A10/A20 SoCs were using pins PC0,PC1,PC2,PC23 for booting
  * from SPI Flash, everything else is using pins PC0,PC1,PC2,PC3.
- * The H6 uses PC0, PC2, PC3, PC5.
+ * The H6 uses PC0, PC2, PC3, PC5, the H616 PC0, PC2, PC3, PC4.
  */
 static void spi0_pinmux_setup(unsigned int pin_function)
 {
@@ -104,11 +104,14 @@ static void spi0_pinmux_setup(unsigned int pin_function)
 	sunxi_gpio_set_cfgpin(SUNXI_GPC(0), pin_function);
 	sunxi_gpio_set_cfgpin(SUNXI_GPC(2), pin_function);
 
-	/* All chips except H6 use PC1, and only H6 uses PC5. */
-	if (!IS_ENABLED(CONFIG_MACH_SUN50I_H6))
+	/* All chips except H6 and H616 use PC1. */
+	if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6))
 		sunxi_gpio_set_cfgpin(SUNXI_GPC(1), pin_function);
-	else
+
+	if (IS_ENABLED(CONFIG_MACH_SUN50I_H6))
 		sunxi_gpio_set_cfgpin(SUNXI_GPC(5), pin_function);
+	if (IS_ENABLED(CONFIG_MACH_SUN50I_H616))
+		sunxi_gpio_set_cfgpin(SUNXI_GPC(4), pin_function);
 
 	/* Older generations use PC23 for CS, newer ones use PC3. */
 	if (IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN7I) ||
@@ -121,7 +124,7 @@ static void spi0_pinmux_setup(unsigned int pin_function)
 static bool is_sun6i_gen_spi(void)
 {
 	return IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) ||
-	       IS_ENABLED(CONFIG_MACH_SUN50I_H6);
+	       IS_ENABLED(CONFIG_SUN50I_GEN_H6);
 }
 
 static uintptr_t spi0_base_address(void)
@@ -129,7 +132,7 @@ static uintptr_t spi0_base_address(void)
 	if (IS_ENABLED(CONFIG_MACH_SUN8I_R40))
 		return 0x01C05000;
 
-	if (IS_ENABLED(CONFIG_MACH_SUN50I_H6))
+	if (IS_ENABLED(CONFIG_SUN50I_GEN_H6))
 		return 0x05010000;
 
 	if (!is_sun6i_gen_spi())
@@ -146,14 +149,14 @@ static void spi0_enable_clock(void)
 	uintptr_t base = spi0_base_address();
 
 	/* Deassert SPI0 reset on SUN6I */
-	if (IS_ENABLED(CONFIG_MACH_SUN50I_H6))
+	if (IS_ENABLED(CONFIG_SUN50I_GEN_H6))
 		setbits_le32(CCM_H6_SPI_BGR_REG, (1U << 16) | 0x1);
 	else if (is_sun6i_gen_spi())
 		setbits_le32(SUN6I_BUS_SOFT_RST_REG0,
 			     (1 << AHB_RESET_SPI0_SHIFT));
 
 	/* Open the SPI0 gate */
-	if (!IS_ENABLED(CONFIG_MACH_SUN50I_H6))
+	if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6))
 		setbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
 
 	/* Divide by 4 */
@@ -194,11 +197,11 @@ static void spi0_disable_clock(void)
 	writel(0, CCM_SPI0_CLK);
 
 	/* Close the SPI0 gate */
-	if (!IS_ENABLED(CONFIG_MACH_SUN50I_H6))
+	if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6))
 		clrbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
 
 	/* Assert SPI0 reset on SUN6I */
-	if (IS_ENABLED(CONFIG_MACH_SUN50I_H6))
+	if (IS_ENABLED(CONFIG_SUN50I_GEN_H6))
 		clrbits_le32(CCM_H6_SPI_BGR_REG, (1U << 16) | 0x1);
 	else if (is_sun6i_gen_spi())
 		clrbits_le32(SUN6I_BUS_SOFT_RST_REG0,
@@ -210,7 +213,7 @@ static void spi0_init(void)
 	unsigned int pin_function = SUNXI_GPC_SPI0;
 
 	if (IS_ENABLED(CONFIG_MACH_SUN50I) ||
-	    IS_ENABLED(CONFIG_MACH_SUN50I_H6))
+	    IS_ENABLED(CONFIG_SUN50I_GEN_H6))
 		pin_function = SUN50I_GPC_SPI0;
 
 	spi0_pinmux_setup(pin_function);
-- 
2.17.5


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH 3/3] sunxi: OrangePi Zero 2: Enable SPI booting
  2021-07-05 23:04 [PATCH 0/3] sunxi: H616: SPI boot support Andre Przywara
  2021-07-05 23:04 ` [PATCH 1/3] sunxi: SPL SPI: Allow larger SPL Andre Przywara
  2021-07-05 23:04 ` [PATCH 2/3] sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC Andre Przywara
@ 2021-07-05 23:04 ` Andre Przywara
  2021-07-06 14:23   ` Jagan Teki
  2 siblings, 1 reply; 7+ messages in thread
From: Andre Przywara @ 2021-07-05 23:04 UTC (permalink / raw)
  To: Jagan Teki; +Cc: Samuel Holland, Jernej Skrabec, u-boot, linux-sunxi

The OrangePi Zero 2 board comes with 2MB of SPI flash, from which the
BROM is supposed to be able to boot from.

Enable the SPL code responsible for finding and loading U-Boot proper and
friends, so that u-boot-sunxi-with-spl.bin can be written into the flash.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 configs/orangepi_zero2_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/configs/orangepi_zero2_defconfig b/configs/orangepi_zero2_defconfig
index 72574a89a29..b99b624dcc3 100644
--- a/configs/orangepi_zero2_defconfig
+++ b/configs/orangepi_zero2_defconfig
@@ -9,6 +9,7 @@ CONFIG_DRAM_SUN50I_H616_WRITE_TRAINING=y
 CONFIG_MACH_SUN50I_H616=y
 CONFIG_MMC0_CD_PIN="PF6"
 CONFIG_R_I2C_ENABLE=y
+CONFIG_SPL_SPI_SUNXI=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_SPL_I2C_SUPPORT=y
 CONFIG_PHY_REALTEK=y
-- 
2.17.5


^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH 1/3] sunxi: SPL SPI: Allow larger SPL
  2021-07-05 23:04 ` [PATCH 1/3] sunxi: SPL SPI: Allow larger SPL Andre Przywara
@ 2021-07-06 14:22   ` Jagan Teki
  0 siblings, 0 replies; 7+ messages in thread
From: Jagan Teki @ 2021-07-06 14:22 UTC (permalink / raw)
  To: Andre Przywara; +Cc: Samuel Holland, Jernej Skrabec, U-Boot-Denx, linux-sunxi

On Tue, Jul 6, 2021 at 4:35 AM Andre Przywara <andre.przywara@arm.com> wrote:
>
> The more recent Allwinner SoCs BootROMs can actually load SPL images
> larger than 32KB. We use this on the H616 to fit the extra code needed
> for the PMIC into the image, and have provisions in board.c to respect
> that larger SPL size when booting from MMC.
>
> However the sunxi SPL SPI loader has a hardcoded load offset of 32KB,
> which will fail on the H616.
>
> To fix this, use the same algorithm we use for MMC: if the SPL size is
> smaller than 32KB, we use 32KB, otherwise we expect the U-Boot payload
> directly after the SPL code.
>
> This prepares for SPI booting with larger SPLs like on the H616.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---

Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH 2/3] sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC
  2021-07-05 23:04 ` [PATCH 2/3] sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC Andre Przywara
@ 2021-07-06 14:22   ` Jagan Teki
  0 siblings, 0 replies; 7+ messages in thread
From: Jagan Teki @ 2021-07-06 14:22 UTC (permalink / raw)
  To: Andre Przywara; +Cc: Samuel Holland, Jernej Skrabec, U-Boot-Denx, linux-sunxi

On Tue, Jul 6, 2021 at 4:35 AM Andre Przywara <andre.przywara@arm.com> wrote:
>
> The H616 SoC uses the same SPI IP as the H6, also shares the same clocks
> and reset bits.
> The only real difference is a slight change in the pin assignment: the
> H6 uses PC5, the H616 PC4 instead. This makes for a small change in
> our spi0_pinmux_setup() routine.
>
> Apart from that, just extend the H6 #ifdef guards to also cover the H616,
> using the shared CONFIG_SUN50I_GEN_H6 symbol.
> Also use this symbol for the Kconfig dependency.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---

Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH 3/3] sunxi: OrangePi Zero 2: Enable SPI booting
  2021-07-05 23:04 ` [PATCH 3/3] sunxi: OrangePi Zero 2: Enable SPI booting Andre Przywara
@ 2021-07-06 14:23   ` Jagan Teki
  0 siblings, 0 replies; 7+ messages in thread
From: Jagan Teki @ 2021-07-06 14:23 UTC (permalink / raw)
  To: Andre Przywara; +Cc: Samuel Holland, Jernej Skrabec, U-Boot-Denx, linux-sunxi

On Tue, Jul 6, 2021 at 4:35 AM Andre Przywara <andre.przywara@arm.com> wrote:
>
> The OrangePi Zero 2 board comes with 2MB of SPI flash, from which the
> BROM is supposed to be able to boot from.
>
> Enable the SPL code responsible for finding and loading U-Boot proper and
> friends, so that u-boot-sunxi-with-spl.bin can be written into the flash.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---

Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, back to index

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-05 23:04 [PATCH 0/3] sunxi: H616: SPI boot support Andre Przywara
2021-07-05 23:04 ` [PATCH 1/3] sunxi: SPL SPI: Allow larger SPL Andre Przywara
2021-07-06 14:22   ` Jagan Teki
2021-07-05 23:04 ` [PATCH 2/3] sunxi: SPL SPI: Add SPI boot support for the Allwinner H616 SoC Andre Przywara
2021-07-06 14:22   ` Jagan Teki
2021-07-05 23:04 ` [PATCH 3/3] sunxi: OrangePi Zero 2: Enable SPI booting Andre Przywara
2021-07-06 14:23   ` Jagan Teki

ARM Sunxi Platform Development

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-sunxi/0 linux-sunxi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-sunxi linux-sunxi/ https://lore.kernel.org/linux-sunxi \
		linux-sunxi@lists.linux.dev
	public-inbox-index linux-sunxi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/dev.linux.lists.linux-sunxi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git