Linux-Tegra Archive on lore.kernel.org
 help / color / Atom feed
From: Sowjanya Komatineni <skomatineni@nvidia.com>
To: <skomatineni@nvidia.com>, <thierry.reding@gmail.com>,
	<jonathanh@nvidia.com>, <frankc@nvidia.com>, <hverkuil@xs4all.nl>,
	<sakari.ailus@iki.fi>, <robh+dt@kernel.org>,
	<helen.koike@collabora.com>
Cc: <digetx@gmail.com>, <gregkh@linuxfoundation.org>,
	<linux-media@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-tegra@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v7 09/10] media: tegra-video: Add CSI MIPI pads calibration
Date: Fri, 31 Jul 2020 14:32:23 -0700
Message-ID: <1596231144-12554-10-git-send-email-skomatineni@nvidia.com> (raw)
In-Reply-To: <1596231144-12554-1-git-send-email-skomatineni@nvidia.com>

CSI MIPI pads need to be enabled and calibrated for capturing from
the external sensor or transmitter.

MIPI CAL unit calibrates MIPI pads pull-up, pull-down and termination
impedances. Calibration is done by co-work of MIPI BIAS pad and MIPI
CAL control unit.

Triggering calibration start can happen any time after MIPI pads are
enabled but calibration results will be latched and applied to MIPI
pads by MIPI CAL unit only when the link is in LP11 state and then
calibration status register gets updated.

This patch enables CSI MIPI pads and calibrates them during streaming.

Tegra CSI receiver is able to catch the very first clock transition.
So, CSI receiver is always enabled prior to sensor streaming and
trigger of calibration start is done during CSI subdev streaming and
status of calibration is verified after sensor stream on.

Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
---
 drivers/staging/media/tegra-video/TODO  |  1 -
 drivers/staging/media/tegra-video/csi.c | 61 +++++++++++++++++++++++++++++++--
 drivers/staging/media/tegra-video/csi.h |  2 ++
 drivers/staging/media/tegra-video/vi.c  | 28 ++++++++++++---
 4 files changed, 84 insertions(+), 8 deletions(-)

diff --git a/drivers/staging/media/tegra-video/TODO b/drivers/staging/media/tegra-video/TODO
index 97a19b4..98d3c7d 100644
--- a/drivers/staging/media/tegra-video/TODO
+++ b/drivers/staging/media/tegra-video/TODO
@@ -1,5 +1,4 @@
 TODO list
-* Add Tegra CSI MIPI pads calibration.
 * Add MIPI clock Settle time computation based on the data rate.
 * Add support for Ganged mode.
 * Add RAW10 packed video format support to Tegra210 video formats.
diff --git a/drivers/staging/media/tegra-video/csi.c b/drivers/staging/media/tegra-video/csi.c
index f308e8c..ea0f941 100644
--- a/drivers/staging/media/tegra-video/csi.c
+++ b/drivers/staging/media/tegra-video/csi.c
@@ -240,7 +240,7 @@ static int tegra_csi_enable_stream(struct v4l2_subdev *subdev)
 	struct tegra_vi_channel *chan = v4l2_get_subdev_hostdata(subdev);
 	struct tegra_csi_channel *csi_chan = to_csi_chan(subdev);
 	struct tegra_csi *csi = csi_chan->csi;
-	int ret;
+	int ret, err;
 
 	ret = pm_runtime_get_sync(csi->dev);
 	if (ret < 0) {
@@ -249,13 +249,47 @@ static int tegra_csi_enable_stream(struct v4l2_subdev *subdev)
 		return ret;
 	}
 
+	if (csi_chan->mipi) {
+		ret = tegra_mipi_enable(csi_chan->mipi);
+		if (ret < 0) {
+			dev_err(csi->dev,
+				"failed to enable MIPI pads: %d\n", ret);
+			goto rpm_put;
+		}
+
+		/*
+		 * CSI MIPI pads PULLUP, PULLDN and TERM impedances need to
+		 * be calibrated after power on.
+		 * So, trigger the calibration start here and results will
+		 * be latched and applied to the pads when link is in LP11
+		 * state during start of sensor streaming.
+		 */
+		ret = tegra_mipi_start_calibration(csi_chan->mipi);
+		if (ret < 0) {
+			dev_err(csi->dev,
+				"failed to start MIPI calibration: %d\n", ret);
+			goto disable_mipi;
+		}
+	}
+
 	csi_chan->pg_mode = chan->pg_mode;
 	ret = csi->ops->csi_start_streaming(csi_chan);
 	if (ret < 0)
-		goto rpm_put;
+		goto cancel_calibration;
 
 	return 0;
 
+cancel_calibration:
+	if (csi_chan->mipi)
+		tegra_mipi_cancel_calibration(csi_chan->mipi);
+disable_mipi:
+	if (csi_chan->mipi) {
+		err = tegra_mipi_disable(csi_chan->mipi);
+		if (err < 0)
+			dev_err(csi->dev,
+				"failed to disable MIPI pads: %d\n", err);
+	}
+
 rpm_put:
 	pm_runtime_put(csi->dev);
 	return ret;
@@ -265,9 +299,17 @@ static int tegra_csi_disable_stream(struct v4l2_subdev *subdev)
 {
 	struct tegra_csi_channel *csi_chan = to_csi_chan(subdev);
 	struct tegra_csi *csi = csi_chan->csi;
+	int err;
 
 	csi->ops->csi_stop_streaming(csi_chan);
 
+	if (csi_chan->mipi) {
+		err = tegra_mipi_disable(csi_chan->mipi);
+		if (err < 0)
+			dev_err(csi->dev,
+				"failed to disable MIPI pads: %d\n", err);
+	}
+
 	pm_runtime_put(csi->dev);
 
 	return 0;
@@ -313,6 +355,7 @@ static int tegra_csi_channel_alloc(struct tegra_csi *csi,
 				   unsigned int num_pads)
 {
 	struct tegra_csi_channel *chan;
+	int ret = 0;
 
 	chan = kzalloc(sizeof(*chan), GFP_KERNEL);
 	if (!chan)
@@ -331,7 +374,16 @@ static int tegra_csi_channel_alloc(struct tegra_csi *csi,
 		chan->pads[0].flags = MEDIA_PAD_FL_SOURCE;
 	}
 
-	return 0;
+	if (IS_ENABLED(CONFIG_VIDEO_TEGRA_TPG))
+		return 0;
+
+	chan->mipi = tegra_mipi_request(csi->dev, node);
+	if (IS_ERR(chan->mipi)) {
+		ret = PTR_ERR(chan->mipi);
+		dev_err(csi->dev, "failed to get mipi device: %d\n", ret);
+	}
+
+	return ret;
 }
 
 static int tegra_csi_tpg_channels_alloc(struct tegra_csi *csi)
@@ -494,6 +546,9 @@ static void tegra_csi_channels_cleanup(struct tegra_csi *csi)
 	struct tegra_csi_channel *chan, *tmp;
 
 	list_for_each_entry_safe(chan, tmp, &csi->csi_chans, list) {
+		if (chan->mipi)
+			tegra_mipi_free(chan->mipi);
+
 		subdev = &chan->subdev;
 		if (subdev->dev) {
 			if (!IS_ENABLED(CONFIG_VIDEO_TEGRA_TPG))
diff --git a/drivers/staging/media/tegra-video/csi.h b/drivers/staging/media/tegra-video/csi.h
index 78a5110..0d50fc3 100644
--- a/drivers/staging/media/tegra-video/csi.h
+++ b/drivers/staging/media/tegra-video/csi.h
@@ -50,6 +50,7 @@ struct tegra_csi;
  * @framerate: active framerate for TPG
  * @h_blank: horizontal blanking for TPG active format
  * @v_blank: vertical blanking for TPG active format
+ * @mipi: mipi device for corresponding csi channel pads
  */
 struct tegra_csi_channel {
 	struct list_head list;
@@ -65,6 +66,7 @@ struct tegra_csi_channel {
 	unsigned int framerate;
 	unsigned int h_blank;
 	unsigned int v_blank;
+	struct tegra_mipi_device *mipi;
 };
 
 /**
diff --git a/drivers/staging/media/tegra-video/vi.c b/drivers/staging/media/tegra-video/vi.c
index 6d0aed0..052072c 100644
--- a/drivers/staging/media/tegra-video/vi.c
+++ b/drivers/staging/media/tegra-video/vi.c
@@ -191,6 +191,7 @@ tegra_channel_get_remote_source_subdev(struct tegra_vi_channel *chan)
 static int tegra_channel_enable_stream(struct tegra_vi_channel *chan)
 {
 	struct v4l2_subdev *csi_subdev, *src_subdev;
+	struct tegra_csi_channel *csi_chan;
 	int ret;
 
 	/*
@@ -206,14 +207,33 @@ static int tegra_channel_enable_stream(struct tegra_vi_channel *chan)
 	if (IS_ENABLED(CONFIG_VIDEO_TEGRA_TPG))
 		return 0;
 
+	csi_chan = v4l2_get_subdevdata(csi_subdev);
+	/*
+	 * TRM has incorrectly documented to wait for done status from
+	 * calibration logic after CSI interface power on.
+	 * As per the design, calibration results are latched and applied
+	 * to the pads only when the link is in LP11 state which will happen
+	 * during the sensor stream-on.
+	 * CSI subdev stream-on triggers start of MIPI pads calibration.
+	 * Wait for calibration to finish here after sensor subdev stream-on
+	 * and in case of sensor stream-on failure, cancel the calibration.
+	 */
 	src_subdev = tegra_channel_get_remote_source_subdev(chan);
 	ret = v4l2_subdev_call(src_subdev, video, s_stream, true);
-	if (ret < 0 && ret != -ENOIOCTLCMD) {
-		v4l2_subdev_call(csi_subdev, video, s_stream, false);
-		return ret;
-	}
+	if (ret < 0 && ret != -ENOIOCTLCMD)
+		goto err_disable_csi_stream;
+
+	ret = tegra_mipi_finish_calibration(csi_chan->mipi);
+	if (ret < 0)
+		dev_warn(csi_chan->csi->dev,
+			 "MIPI calibration failed: %d\n", ret);
 
 	return 0;
+
+err_disable_csi_stream:
+	tegra_mipi_cancel_calibration(csi_chan->mipi);
+	v4l2_subdev_call(csi_subdev, video, s_stream, false);
+	return ret;
 }
 
 static int tegra_channel_disable_stream(struct tegra_vi_channel *chan)
-- 
2.7.4


  parent reply index

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-31 21:32 [PATCH v7 00/10] Support for Tegra video capture from external sensor Sowjanya Komatineni
2020-07-31 21:32 ` [PATCH v7 01/10] media: tegra-video: Fix channel format alignment Sowjanya Komatineni
2020-07-31 21:32 ` [PATCH v7 02/10] media: tegra-video: Enable TPG based on kernel config Sowjanya Komatineni
2020-07-31 21:32 ` [PATCH v7 03/10] media: tegra-video: Update format lookup to offset based Sowjanya Komatineni
2020-07-31 21:32 ` [PATCH v7 04/10] dt-bindings: tegra: Update VI and CSI bindings with port info Sowjanya Komatineni
2020-07-31 21:32 ` [PATCH v7 05/10] media: tegra-video: Separate CSI stream enable and disable implementations Sowjanya Komatineni
2020-07-31 21:32 ` [PATCH v7 06/10] media: tegra-video: Add support for external sensor capture Sowjanya Komatineni
2020-08-01  0:59   ` Dmitry Osipenko
2020-07-31 21:32 ` [PATCH v7 07/10] media: tegra-video: Add support for selection ioctl ops Sowjanya Komatineni
2020-07-31 21:32 ` [PATCH v7 08/10] gpu: host1x: mipi: Keep MIPI clock enabled till calibration is done Sowjanya Komatineni
2020-07-31 21:32 ` Sowjanya Komatineni [this message]
2020-08-01  1:04   ` [PATCH v7 09/10] media: tegra-video: Add CSI MIPI pads calibration Dmitry Osipenko
2020-07-31 21:32 ` [PATCH v7 10/10] media: tegra-video: Compute settle times based on the clock rate Sowjanya Komatineni

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1596231144-12554-10-git-send-email-skomatineni@nvidia.com \
    --to=skomatineni@nvidia.com \
    --cc=devicetree@vger.kernel.org \
    --cc=digetx@gmail.com \
    --cc=frankc@nvidia.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=helen.koike@collabora.com \
    --cc=hverkuil@xs4all.nl \
    --cc=jonathanh@nvidia.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-tegra@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=sakari.ailus@iki.fi \
    --cc=thierry.reding@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Tegra Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-tegra/0 linux-tegra/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-tegra linux-tegra/ https://lore.kernel.org/linux-tegra \
		linux-tegra@vger.kernel.org
	public-inbox-index linux-tegra

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-tegra


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git