From: Thierry Reding <thierry.reding@gmail.com>
To: JC Kuo <jckuo@nvidia.com>
Cc: gregkh@linuxfoundation.org, jonathanh@nvidia.com,
linux-tegra@vger.kernel.org, linux-usb@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
nkristam@nvidia.com, skomatineni@nvidia.com
Subject: Re: [PATCH 4/6] dt-bindings: phy: tegra: Add Tegra194 support
Date: Wed, 2 Oct 2019 11:44:38 +0200 [thread overview]
Message-ID: <20191002094438.GD3716706@ulmo> (raw)
In-Reply-To: <20191002080051.11142-5-jckuo@nvidia.com>
[-- Attachment #1: Type: text/plain, Size: 3007 bytes --]
On Wed, Oct 02, 2019 at 04:00:49PM +0800, JC Kuo wrote:
> Extend the bindings to cover the set of features found in Tegra194.
> Note that, technically, there are four more supplies connected to the
> XUSB pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL)
> , but the power sequencing requirements of Tegra194 require these to be
> under the control of the PMIC.
>
> Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it is
> possible for some platforms have long signal trace that could not
> provide sufficient electrical environment for Gen 2 speed. To deal with
> this, a new device node property "nvidia,disable-gen2" was added to
> Tegra194 that be used to specifically disable Gen 2 speed for a
> particular USB 3.0 port so that the port can be limited to Gen 1 speed
> and avoid the instability.
>
> Signed-off-by: JC Kuo <jckuo@nvidia.com>
> ---
> .../bindings/phy/nvidia,tegra124-xusb-padctl.txt | 16 ++++++++++++++++
> 1 file changed, 16 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
> index 9fb682e47c29..3bef37e7c365 100644
> --- a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
> +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt
> @@ -37,6 +37,7 @@ Required properties:
> - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
> - Tegra210: "nvidia,tegra210-xusb-padctl"
> - Tegra186: "nvidia,tegra186-xusb-padctl"
> + - Tegra194: "nvidia,tegra194-xusb-padctl"
> - reg: Physical base address and length of the controller's registers.
> - resets: Must contain an entry for each entry in reset-names.
> - reset-names: Must include the following entries:
> @@ -62,6 +63,10 @@ For Tegra186:
> - vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
> - vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
>
> +For Tegra194:
> +- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
> + 3.3 V.
> +- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
>
> Pad nodes:
> ==========
> @@ -154,6 +159,11 @@ For Tegra210, the list of valid PHY nodes is given below:
> - sata: sata-0
> - functions: "usb3-ss", "sata"
>
> +For Tegra194, the list of valid PHY nodes is given below:
> +- usb2: usb2-0, usb2-1, usb2-2, usb2-3
> + - functions: "xusb"
> +- usb3: usb3-0, usb3-1, usb3-2, usb3-3
> + - functions: "xusb"
>
> Port nodes:
> ===========
> @@ -221,6 +231,9 @@ Optional properties:
> is internal. In the absence of this property the port is considered to be
> external.
>
> +- nvidia,disable-gen2: A boolean property whose presence determines that a port
> + should be limited to USB 3.1 Gen 1. This properlty is only for Tegra194.
s/properlty/property/
With that:
Acked-by: Thierry Reding <treding@nvidia.com>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
next prev parent reply other threads:[~2019-10-02 9:44 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-02 8:00 [PATCH 0/6] Add Tegra194 XUSB host and pad controller support JC Kuo
2019-10-02 8:00 ` [PATCH 1/6] xhci: tegra: Parameterize mailbox register addresses JC Kuo
2019-10-02 9:39 ` Thierry Reding
2019-10-02 8:00 ` [PATCH 2/6] usb: host: xhci-tegra: Add Tegra194 XHCI support JC Kuo
2019-10-02 9:40 ` Thierry Reding
2019-10-02 8:00 ` [PATCH 3/6] phy: tegra: xusb: Add Tegra194 support JC Kuo
2019-10-02 10:02 ` Thierry Reding
2019-10-03 2:00 ` JC Kuo
2019-10-02 8:00 ` [PATCH 4/6] dt-bindings: phy: tegra: " JC Kuo
2019-10-02 9:44 ` Thierry Reding [this message]
2019-10-03 1:50 ` JC Kuo
2019-10-02 8:00 ` [PATCH 5/6] arm64: tegra: Add XUSB and pad controller on Tegra194 JC Kuo
2019-10-02 10:10 ` Thierry Reding
2019-10-03 2:04 ` JC Kuo
2019-10-02 10:11 ` Thierry Reding
2019-10-03 2:06 ` JC Kuo
2019-10-02 8:00 ` [PATCH 6/6] arm64: tegra: Enable XUSB host in P2972-0000 board JC Kuo
2019-10-02 10:26 ` Thierry Reding
2019-10-03 6:00 ` JC Kuo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191002094438.GD3716706@ulmo \
--to=thierry.reding@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jckuo@nvidia.com \
--cc=jonathanh@nvidia.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=nkristam@nvidia.com \
--cc=skomatineni@nvidia.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).