From: JC Kuo <jckuo@nvidia.com>
To: <gregkh@linuxfoundation.org>, <thierry.reding@gmail.com>,
<jonathanh@nvidia.com>
Cc: <linux-tegra@vger.kernel.org>, <linux-usb@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<nkristam@nvidia.com>, <skomatineni@nvidia.com>,
JC Kuo <jckuo@nvidia.com>
Subject: [PATCH v2 4/7] phy: tegra: xusb: Add Tegra194 support
Date: Fri, 4 Oct 2019 16:19:38 +0800 [thread overview]
Message-ID: <20191004081941.4831-5-jckuo@nvidia.com> (raw)
In-Reply-To: <20191004081941.4831-1-jckuo@nvidia.com>
Add support for the XUSB pad controller found on Tegra194 SoCs. It is
mostly similar to the same IP found on Tegra186, but the number of
pads exposed differs, as do the programming sequences. Because most of
the Tegra194 XUSB PADCTL registers definition and programming sequence
are the same as Tegra186, Tegra194 XUSB PADCTL can share the same
driver, xusb-tegra186.c, with Tegra186 XUSB PADCTL.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
introduce a new device node property "nvidia,disable-gen2" that can
be used to specifically disable Gen 2 speed for a particular USB 3.0
port so that the port can be limited to Gen 1 speed and avoid the
instability.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
---
Changes in v2:
- removed unnecessary #if/#endif pairs
- introduce new soc->supports_gen2 flag which indicate whether or not
a soc supports USB 3.1 Gen 2 speed
drivers/phy/tegra/Makefile | 1 +
drivers/phy/tegra/xusb-tegra186.c | 74 +++++++++++++++++++++++++++++++
drivers/phy/tegra/xusb.c | 7 +++
drivers/phy/tegra/xusb.h | 6 +++
4 files changed, 88 insertions(+)
diff --git a/drivers/phy/tegra/Makefile b/drivers/phy/tegra/Makefile
index 320dd389f34d..89b84067cb4c 100644
--- a/drivers/phy/tegra/Makefile
+++ b/drivers/phy/tegra/Makefile
@@ -6,4 +6,5 @@ phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_124_SOC) += xusb-tegra124.o
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_132_SOC) += xusb-tegra124.o
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_210_SOC) += xusb-tegra210.o
phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_186_SOC) += xusb-tegra186.o
+phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_194_SOC) += xusb-tegra186.o
obj-$(CONFIG_PHY_TEGRA194_P2U) += phy-tegra194-p2u.o
diff --git a/drivers/phy/tegra/xusb-tegra186.c b/drivers/phy/tegra/xusb-tegra186.c
index 3b60270f2009..74baa1dbca6c 100644
--- a/drivers/phy/tegra/xusb-tegra186.c
+++ b/drivers/phy/tegra/xusb-tegra186.c
@@ -64,6 +64,11 @@
#define SSPX_ELPG_CLAMP_EN_EARLY(x) BIT(1 + (x) * 3)
#define SSPX_ELPG_VCORE_DOWN(x) BIT(2 + (x) * 3)
+#define XUSB_PADCTL_SS_PORT_CFG 0x2c
+#define PORTX_SPEED_SUPPORT_SHIFT(x) ((x) * 4)
+#define PORTX_SPEED_SUPPORT_MASK (0x3)
+#define PORT_SPEED_SUPPORT_GEN1 (0x0)
+
#define XUSB_PADCTL_USB2_OTG_PADX_CTL0(x) (0x88 + (x) * 0x40)
#define HS_CURR_LEVEL(x) ((x) & 0x3f)
#define TERM_SEL BIT(25)
@@ -622,6 +627,15 @@ static int tegra186_usb3_phy_power_on(struct phy *phy)
padctl_writel(padctl, value, XUSB_PADCTL_SS_PORT_CAP);
+ if (padctl->soc->supports_gen2 && port->disable_gen2) {
+ value = padctl_readl(padctl, XUSB_PADCTL_SS_PORT_CFG);
+ value &= ~(PORTX_SPEED_SUPPORT_MASK <<
+ PORTX_SPEED_SUPPORT_SHIFT(index));
+ value |= (PORT_SPEED_SUPPORT_GEN1 <<
+ PORTX_SPEED_SUPPORT_SHIFT(index));
+ padctl_writel(padctl, value, XUSB_PADCTL_SS_PORT_CFG);
+ }
+
value = padctl_readl(padctl, XUSB_PADCTL_ELPG_PROGRAM_1);
value &= ~SSPX_ELPG_VCORE_DOWN(index);
padctl_writel(padctl, value, XUSB_PADCTL_ELPG_PROGRAM_1);
@@ -896,6 +910,66 @@ const struct tegra_xusb_padctl_soc tegra186_xusb_padctl_soc = {
EXPORT_SYMBOL_GPL(tegra186_xusb_padctl_soc);
#endif
+#if IS_ENABLED(CONFIG_ARCH_TEGRA_194_SOC)
+static const char * const tegra194_xusb_padctl_supply_names[] = {
+ "avdd-usb",
+ "vclamp-usb",
+};
+
+static const struct tegra_xusb_lane_soc tegra194_usb2_lanes[] = {
+ TEGRA186_LANE("usb2-0", 0, 0, 0, usb2),
+ TEGRA186_LANE("usb2-1", 0, 0, 0, usb2),
+ TEGRA186_LANE("usb2-2", 0, 0, 0, usb2),
+ TEGRA186_LANE("usb2-3", 0, 0, 0, usb2),
+};
+
+static const struct tegra_xusb_pad_soc tegra194_usb2_pad = {
+ .name = "usb2",
+ .num_lanes = ARRAY_SIZE(tegra194_usb2_lanes),
+ .lanes = tegra194_usb2_lanes,
+ .ops = &tegra186_usb2_pad_ops,
+};
+
+static const struct tegra_xusb_lane_soc tegra194_usb3_lanes[] = {
+ TEGRA186_LANE("usb3-0", 0, 0, 0, usb3),
+ TEGRA186_LANE("usb3-1", 0, 0, 0, usb3),
+ TEGRA186_LANE("usb3-2", 0, 0, 0, usb3),
+ TEGRA186_LANE("usb3-3", 0, 0, 0, usb3),
+};
+
+static const struct tegra_xusb_pad_soc tegra194_usb3_pad = {
+ .name = "usb3",
+ .num_lanes = ARRAY_SIZE(tegra194_usb3_lanes),
+ .lanes = tegra194_usb3_lanes,
+ .ops = &tegra186_usb3_pad_ops,
+};
+
+static const struct tegra_xusb_pad_soc * const tegra194_pads[] = {
+ &tegra194_usb2_pad,
+ &tegra194_usb3_pad,
+};
+
+const struct tegra_xusb_padctl_soc tegra194_xusb_padctl_soc = {
+ .num_pads = ARRAY_SIZE(tegra194_pads),
+ .pads = tegra194_pads,
+ .ports = {
+ .usb2 = {
+ .ops = &tegra186_usb2_port_ops,
+ .count = 4,
+ },
+ .usb3 = {
+ .ops = &tegra186_usb3_port_ops,
+ .count = 4,
+ },
+ },
+ .ops = &tegra186_xusb_padctl_ops,
+ .supply_names = tegra194_xusb_padctl_supply_names,
+ .num_supplies = ARRAY_SIZE(tegra194_xusb_padctl_supply_names),
+ .supports_gen2 = true,
+};
+EXPORT_SYMBOL_GPL(tegra194_xusb_padctl_soc);
+#endif
+
MODULE_AUTHOR("JC Kuo <jckuo@nvidia.com>");
MODULE_DESCRIPTION("NVIDIA Tegra186 XUSB Pad Controller driver");
MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/tegra/xusb.c b/drivers/phy/tegra/xusb.c
index 2ea8497af82a..e359a75d9543 100644
--- a/drivers/phy/tegra/xusb.c
+++ b/drivers/phy/tegra/xusb.c
@@ -65,6 +65,12 @@ static const struct of_device_id tegra_xusb_padctl_of_match[] = {
.compatible = "nvidia,tegra186-xusb-padctl",
.data = &tegra186_xusb_padctl_soc,
},
+#endif
+#if defined(CONFIG_ARCH_TEGRA_194_SOC)
+ {
+ .compatible = "nvidia,tegra194-xusb-padctl",
+ .data = &tegra194_xusb_padctl_soc,
+ },
#endif
{ }
};
@@ -738,6 +744,7 @@ static int tegra_xusb_usb3_port_parse_dt(struct tegra_xusb_usb3_port *usb3)
usb3->port = value;
usb3->internal = of_property_read_bool(np, "nvidia,internal");
+ usb3->disable_gen2 = of_property_read_bool(np, "nvidia,disable-gen2");
usb3->supply = devm_regulator_get(&port->dev, "vbus");
return PTR_ERR_OR_ZERO(usb3->supply);
diff --git a/drivers/phy/tegra/xusb.h b/drivers/phy/tegra/xusb.h
index 093076ca27fd..8312129caf96 100644
--- a/drivers/phy/tegra/xusb.h
+++ b/drivers/phy/tegra/xusb.h
@@ -332,6 +332,7 @@ struct tegra_xusb_usb3_port {
bool context_saved;
unsigned int port;
bool internal;
+ bool disable_gen2;
u32 tap1;
u32 amp;
@@ -389,6 +390,8 @@ struct tegra_xusb_padctl_soc {
const char * const *supply_names;
unsigned int num_supplies;
+
+ bool supports_gen2;
};
struct tegra_xusb_padctl {
@@ -444,5 +447,8 @@ extern const struct tegra_xusb_padctl_soc tegra210_xusb_padctl_soc;
#if defined(CONFIG_ARCH_TEGRA_186_SOC)
extern const struct tegra_xusb_padctl_soc tegra186_xusb_padctl_soc;
#endif
+#if defined(CONFIG_ARCH_TEGRA_194_SOC)
+extern const struct tegra_xusb_padctl_soc tegra194_xusb_padctl_soc;
+#endif
#endif /* __PHY_TEGRA_XUSB_H */
--
2.17.1
next prev parent reply other threads:[~2019-10-04 8:20 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-04 8:19 [PATCH v2 0/7] add Tegra194 XUSB host and pad controller support JC Kuo
2019-10-04 8:19 ` [PATCH v2 1/7] xhci: tegra: Parameterize mailbox register addresses JC Kuo
2019-10-04 8:19 ` [PATCH v2 2/7] usb: host: xhci-tegra: Add Tegra194 XHCI support JC Kuo
2019-10-04 8:19 ` [PATCH v2 3/7] phy: tegra: xusb: Protect Tegra186 soc with config JC Kuo
2019-10-04 8:19 ` JC Kuo [this message]
2019-10-04 8:19 ` [PATCH v2 5/7] dt-bindings: phy: tegra: Add Tegra194 support JC Kuo
2019-10-04 8:19 ` [PATCH v2 6/7] arm64: tegra: Add XUSB and pad controller on Tegra194 JC Kuo
2019-10-04 8:19 ` [PATCH v2 7/7] arm64: tegra: Enable XUSB host in P2972-0000 board JC Kuo
2019-10-04 12:23 ` [PATCH v2 0/7] add Tegra194 XUSB host and pad controller support Greg KH
2019-10-04 16:08 ` JC Kuo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191004081941.4831-5-jckuo@nvidia.com \
--to=jckuo@nvidia.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jonathanh@nvidia.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=nkristam@nvidia.com \
--cc=skomatineni@nvidia.com \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).