Linux-USB Archive on lore.kernel.org
 help / color / Atom feed
From: Thierry Reding <thierry.reding@gmail.com>
To: JC Kuo <jckuo@nvidia.com>
Cc: gregkh@linuxfoundation.org, robh@kernel.org,
	jonathanh@nvidia.com, kishon@ti.com, linux-tegra@vger.kernel.org,
	linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
	devicetree@vger.kernel.org, nkristam@nvidia.com
Subject: Re: [PATCH v3 03/15] phy: tegra: xusb: Move usb3 port init for Tegra210
Date: Mon, 28 Sep 2020 15:03:28 +0200
Message-ID: <20200928130328.GD3065790@ulmo> (raw)
In-Reply-To: <20200909081041.3190157-4-jckuo@nvidia.com>


[-- Attachment #1: Type: text/plain, Size: 997 bytes --]

On Wed, Sep 09, 2020 at 04:10:29PM +0800, JC Kuo wrote:
> The programming sequence in tegra210_usb3_port_enable() is required
> for both cold boot and SC7 exit, and must be performed only after
> PEX/SATA UPHY is initialized. Therefore, this commit moves the
> programming sequence to tegra210_usb3_phy_power_on(). PCIE/SATA phy
> .power_on() stub will invoke tegra210_usb3_phy_power_on() if the lane
> is assigned for XUSB super-speed.
> 
> Signed-off-by: JC Kuo <jckuo@nvidia.com>
> ---
> v3:
>    new, was a part of "phy: tegra: xusb: Rearrange UPHY init on Tegra210"
> 
>  drivers/phy/tegra/xusb-tegra210.c | 298 +++++++++++++++++-------------
>  drivers/phy/tegra/xusb.c          |   2 +-
>  drivers/phy/tegra/xusb.h          |   2 +
>  3 files changed, 174 insertions(+), 128 deletions(-)

I'm a bit unhappy about the repeated calls to tegra_xusb_lane_check(),
but I don't have any great ideas on how to improve this, so:

Acked-by: Thierry Reding <treding@nvidia.com>

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

  reply index

Thread overview: 39+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-09-09  8:10 [PATCH v3 00/15] Tegra XHCI controller ELPG support JC Kuo
2020-09-09  8:10 ` [PATCH v3 01/15] clk: tegra: Add PLLE HW power sequencer control JC Kuo
2020-09-28 12:51   ` Thierry Reding
2020-09-09  8:10 ` [PATCH v3 02/15] clk: tegra: Don't enable PLLE HW sequencer at init JC Kuo
2020-09-28 12:52   ` Thierry Reding
2020-09-09  8:10 ` [PATCH v3 03/15] phy: tegra: xusb: Move usb3 port init for Tegra210 JC Kuo
2020-09-28 13:03   ` Thierry Reding [this message]
2020-09-09  8:10 ` [PATCH v3 04/15] phy: tegra: xusb: tegra210: Do not reset UPHY PLL JC Kuo
2020-09-28 13:06   ` Thierry Reding
2020-10-14  3:21     ` JC Kuo
2020-09-09  8:10 ` [PATCH v3 05/15] phy: tegra: xusb: Rearrange UPHY init on Tegra210 JC Kuo
2020-09-28 13:08   ` Thierry Reding
2020-09-09  8:10 ` [PATCH v3 06/15] phy: tegra: xusb: Add Tegra210 lane_iddq operation JC Kuo
2020-09-28 13:10   ` Thierry Reding
2020-09-09  8:10 ` [PATCH v3 07/15] phy: tegra: xusb: Add sleepwalk and suspend/resume JC Kuo
2020-09-28 13:11   ` Thierry Reding
2020-09-09  8:10 ` [PATCH v3 08/15] soc/tegra: pmc: Provide usb sleepwalk register map JC Kuo
2020-09-28 13:17   ` Thierry Reding
2020-10-14  4:08     ` JC Kuo
2020-09-09  8:10 ` [PATCH v3 09/15] arm64: tegra210: XUSB PADCTL add "nvidia,pmc" prop JC Kuo
2020-09-28 13:18   ` Thierry Reding
2020-10-14  4:15     ` JC Kuo
2020-09-09  8:10 ` [PATCH v3 10/15] phy: tegra: xusb: Add wake/sleepwalk for Tegra210 JC Kuo
2020-09-28 13:40   ` Thierry Reding
2020-10-14  8:37     ` JC Kuo
2020-09-09  8:10 ` [PATCH v3 11/15] phy: tegra: xusb: Tegra210 host mode VBUS control JC Kuo
2020-09-28 13:42   ` Thierry Reding
2020-09-09  8:10 ` [PATCH v3 12/15] phy: tegra: xusb: Add wake/sleepwalk for Tegra186 JC Kuo
2020-09-28 13:50   ` Thierry Reding
2020-10-15  8:08     ` JC Kuo
2020-09-09  8:10 ` [PATCH v3 13/15] arm64: tegra210/tegra186/tegra194: XUSB PADCTL irq JC Kuo
2020-09-09  8:10 ` [PATCH v3 14/15] usb: host: xhci-tegra: Unlink power domain devices JC Kuo
2020-09-28 13:53   ` Thierry Reding
2020-10-15  8:09     ` JC Kuo
2020-09-09  8:10 ` [PATCH v3 15/15] xhci: tegra: Enable ELPG for runtime/system PM JC Kuo
2020-09-28 14:06   ` Thierry Reding
2020-10-15  8:12     ` JC Kuo
2020-09-28 12:54 ` [PATCH v3 00/15] Tegra XHCI controller ELPG support Thierry Reding
2020-10-14  2:26   ` JC Kuo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200928130328.GD3065790@ulmo \
    --to=thierry.reding@gmail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=jckuo@nvidia.com \
    --cc=jonathanh@nvidia.com \
    --cc=kishon@ti.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-tegra@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=nkristam@nvidia.com \
    --cc=robh@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-USB Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-usb/0 linux-usb/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-usb linux-usb/ https://lore.kernel.org/linux-usb \
		linux-usb@vger.kernel.org
	public-inbox-index linux-usb

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-usb


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git