Linux-USB Archive on lore.kernel.org
 help / color / Atom feed
* Re: kexec on rk3399
       [not found] <ebcb52be-2063-4e2c-9a09-fdcacb94f855@gmail.com>
@ 2019-08-14 12:53 ` Vicente Bergas
  2019-08-14 13:06   ` Felipe Balbi
  2019-08-14 13:12   ` Robin Murphy
  0 siblings, 2 replies; 18+ messages in thread
From: Vicente Bergas @ 2019-08-14 12:53 UTC (permalink / raw)
  To: Felipe Balbi, Robin Murphy
  Cc: Heiko Stuebner, Will Deacon, Marc Zyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip, linux-kernel

On Monday, July 22, 2019 4:31:27 PM CEST, Vicente Bergas wrote:
> Hi, i have been running linux on rk3399 booted with kexec fine until 5.2
> From 5.2 onwards, there are memory corruption issues as reported here:
> http://lkml.iu.edu/hypermail/linux/kernel/1906.2/07211.html
> kexec has been identified as the principal reason for the issues.
>
> It turns out that kexec has never worked reliably on this platform,
> i was just lucky until recently.
>
> Please, can you provide some directions on how to debug the issue?

Thank you all for your suggestions on where the issue could be.

It seems that it was the USB driver.
Now using v5.2.8 booted with kexec from v5.2.8 with a workaround and
so far so good. It is being tested on the Sapphire board.

The workaround is:
--- a/drivers/usb/dwc3/dwc3-of-simple.c
+++ b/drivers/usb/dwc3/dwc3-of-simple.c
@@ -133,6 +133,13 @@
 	return 0;
 }
 
+static void dwc3_of_simple_shutdown(struct platform_device *pdev)
+{
+	struct dwc3_of_simple *simple = platform_get_drvdata(pdev);
+
+	reset_control_assert(simple->resets);
+}
+
 static int __maybe_unused dwc3_of_simple_runtime_suspend(struct device 
*dev)
 {
 	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
@@ -190,6 +197,7 @@
 static struct platform_driver dwc3_of_simple_driver = {
 	.probe		= dwc3_of_simple_probe,
 	.remove		= dwc3_of_simple_remove,
+	.shutdown	= dwc3_of_simple_shutdown,
 	.driver		= {
 		.name	= "dwc3-of-simple",
 		.of_match_table = of_dwc3_simple_match,

If this patch is OK after review i can resubmit it as a pull request.
Should a similar change be applied to drivers/usb/dwc3/core.c ?

Regards,
  Vicenç.


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: kexec on rk3399
  2019-08-14 12:53 ` kexec on rk3399 Vicente Bergas
@ 2019-08-14 13:06   ` Felipe Balbi
  2019-08-14 13:15     ` Vicente Bergas
  2019-08-14 13:12   ` Robin Murphy
  1 sibling, 1 reply; 18+ messages in thread
From: Felipe Balbi @ 2019-08-14 13:06 UTC (permalink / raw)
  To: Vicente Bergas, Robin Murphy
  Cc: Heiko Stuebner, Will Deacon, Marc Zyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip, linux-kernel

[-- Attachment #1: Type: text/plain, Size: 2085 bytes --]


Hi,

Vicente Bergas <vicencb@gmail.com> writes:
> On Monday, July 22, 2019 4:31:27 PM CEST, Vicente Bergas wrote:
>> Hi, i have been running linux on rk3399 booted with kexec fine until 5.2
>> From 5.2 onwards, there are memory corruption issues as reported here:
>> http://lkml.iu.edu/hypermail/linux/kernel/1906.2/07211.html
>> kexec has been identified as the principal reason for the issues.
>>
>> It turns out that kexec has never worked reliably on this platform,
>> i was just lucky until recently.
>>
>> Please, can you provide some directions on how to debug the issue?
>
> Thank you all for your suggestions on where the issue could be.
>
> It seems that it was the USB driver.
> Now using v5.2.8 booted with kexec from v5.2.8 with a workaround and
> so far so good. It is being tested on the Sapphire board.
>
> The workaround is:
> --- a/drivers/usb/dwc3/dwc3-of-simple.c
> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
> @@ -133,6 +133,13 @@
>  	return 0;
>  }
>  
> +static void dwc3_of_simple_shutdown(struct platform_device *pdev)
> +{
> +	struct dwc3_of_simple *simple = platform_get_drvdata(pdev);
> +
> +	reset_control_assert(simple->resets);
> +}
> +
>  static int __maybe_unused dwc3_of_simple_runtime_suspend(struct device 
> *dev)
>  {
>  	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
> @@ -190,6 +197,7 @@
>  static struct platform_driver dwc3_of_simple_driver = {
>  	.probe		= dwc3_of_simple_probe,
>  	.remove		= dwc3_of_simple_remove,
> +	.shutdown	= dwc3_of_simple_shutdown,
>  	.driver		= {
>  		.name	= "dwc3-of-simple",
>  		.of_match_table = of_dwc3_simple_match,
>
> If this patch is OK after review i can resubmit it as a pull request.

not a pull request, just send a patch using git send-email

> Should a similar change be applied to drivers/usb/dwc3/core.c ?

Is it necessary? We haven't had any bug reports regarding that. Also, if
we have reset control support in the core driver, why do we need it in
of_simple? Seems like of_simple could just rely on what core does.

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: kexec on rk3399
  2019-08-14 12:53 ` kexec on rk3399 Vicente Bergas
  2019-08-14 13:06   ` Felipe Balbi
@ 2019-08-14 13:12   ` Robin Murphy
  2019-08-15  1:15     ` Vicente Bergas
  1 sibling, 1 reply; 18+ messages in thread
From: Robin Murphy @ 2019-08-14 13:12 UTC (permalink / raw)
  To: Vicente Bergas, Felipe Balbi
  Cc: Heiko Stuebner, Will Deacon, Marc Zyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip, linux-kernel

On 14/08/2019 13:53, Vicente Bergas wrote:
> On Monday, July 22, 2019 4:31:27 PM CEST, Vicente Bergas wrote:
>> Hi, i have been running linux on rk3399 booted with kexec fine until 5.2
>> From 5.2 onwards, there are memory corruption issues as reported here:
>> http://lkml.iu.edu/hypermail/linux/kernel/1906.2/07211.html
>> kexec has been identified as the principal reason for the issues.
>>
>> It turns out that kexec has never worked reliably on this platform,
>> i was just lucky until recently.
>>
>> Please, can you provide some directions on how to debug the issue?
> 
> Thank you all for your suggestions on where the issue could be.
> 
> It seems that it was the USB driver.
> Now using v5.2.8 booted with kexec from v5.2.8 with a workaround and
> so far so good. It is being tested on the Sapphire board.
> 
> The workaround is:
> --- a/drivers/usb/dwc3/dwc3-of-simple.c
> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
> @@ -133,6 +133,13 @@
>      return 0;
> }
> 
> +static void dwc3_of_simple_shutdown(struct platform_device *pdev)
> +{
> +    struct dwc3_of_simple *simple = platform_get_drvdata(pdev);
> +
> +    reset_control_assert(simple->resets);
> +}
> +
> static int __maybe_unused dwc3_of_simple_runtime_suspend(struct device 
> *dev)
> {
>      struct dwc3_of_simple    *simple = dev_get_drvdata(dev);
> @@ -190,6 +197,7 @@
> static struct platform_driver dwc3_of_simple_driver = {
>      .probe        = dwc3_of_simple_probe,
>      .remove        = dwc3_of_simple_remove,
> +    .shutdown    = dwc3_of_simple_shutdown,
>      .driver        = {
>          .name    = "dwc3-of-simple",
>          .of_match_table = of_dwc3_simple_match,
> 
> If this patch is OK after review i can resubmit it as a pull request.
> Should a similar change be applied to drivers/usb/dwc3/core.c ?

This particular change looks like it's implicitly specific to RK3399, 
which wouldn't be ideal. Presumably if the core dwc3 driver implemented 
shutdown correctly (echoing parts of dwc3_remove(), I guess) then the 
glue layers shouldn't need anything special anyway.

Robin.

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: kexec on rk3399
  2019-08-14 13:06   ` Felipe Balbi
@ 2019-08-14 13:15     ` Vicente Bergas
  2019-08-15  6:00       ` Felipe Balbi
  0 siblings, 1 reply; 18+ messages in thread
From: Vicente Bergas @ 2019-08-14 13:15 UTC (permalink / raw)
  To: Felipe Balbi
  Cc: Robin Murphy, Heiko Stuebner, Will Deacon, Marc Zyngier,
	Catalin Marinas, Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip, linux-kernel

On Wednesday, August 14, 2019 3:06:04 PM CEST, Felipe Balbi wrote:
> Hi,
>
> Vicente Bergas <vicencb@gmail.com> writes:
>> On Monday, July 22, 2019 4:31:27 PM CEST, Vicente Bergas wrote:
>>> Hi, i have been running linux on rk3399 booted with kexec fine until 5.2
>>> From 5.2 onwards, there are memory corruption issues as reported here:
>>> http://lkml.iu.edu/hypermail/linux/kernel/1906.2/07211.html
>>> kexec has been identified as the principal reason for the issues.
>>> 
>>> It turns out that kexec has never worked reliably on this platform, ...
>> 
>> Thank you all for your suggestions on where the issue could be.
>> 
>> It seems that it was the USB driver.
>> Now using v5.2.8 booted with kexec from v5.2.8 with a workaround and
>> so far so good. It is being tested on the Sapphire board.
>> 
>> The workaround is:
>> --- a/drivers/usb/dwc3/dwc3-of-simple.c
>> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
>> @@ -133,6 +133,13 @@
>>  	return 0;
>>  }
>>  
>> +static void dwc3_of_simple_shutdown(struct platform_device *pdev)
>> +{
>> +	struct dwc3_of_simple *simple = platform_get_drvdata(pdev);
>> +
>> +	reset_control_assert(simple->resets);
>> +}
>> +
>>  static int __maybe_unused dwc3_of_simple_runtime_suspend(struct device 
>> *dev)
>>  {
>>  	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
>> @@ -190,6 +197,7 @@
>>  static struct platform_driver dwc3_of_simple_driver = {
>>  	.probe		= dwc3_of_simple_probe,
>>  	.remove		= dwc3_of_simple_remove,
>> +	.shutdown	= dwc3_of_simple_shutdown,
>>  	.driver		= {
>>  		.name	= "dwc3-of-simple",
>>  		.of_match_table = of_dwc3_simple_match,
>> 
>> If this patch is OK after review i can resubmit it as a pull request.
>
> not a pull request, just send a patch using git send-email
>
>> Should a similar change be applied to drivers/usb/dwc3/core.c ?
>
> Is it necessary? We haven't had any bug reports regarding that. Also, if
> we have reset control support in the core driver, why do we need it in
> of_simple? Seems like of_simple could just rely on what core does.

the workaround has been tested patching only core.c with
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -1561,6 +1561,13 @@
 	return 0;
 }
 
+static void dwc3_shutdown(struct platform_device *pdev)
+{
+	struct dwc3 *dwc = platform_get_drvdata(pdev);
+
+	reset_control_assert(dwc->reset);
+}
+
 #ifdef CONFIG_PM
 static int dwc3_core_init_for_resume(struct dwc3 *dwc)
 {
@@ -1866,6 +1873,7 @@
 static struct platform_driver dwc3_driver = {
 	.probe		= dwc3_probe,
 	.remove		= dwc3_remove,
+	.shutdown	= dwc3_shutdown,
 	.driver		= {
 		.name	= "dwc3",
 		.of_match_table	= of_match_ptr(of_dwc3_match),

and leaving dwc3-of-simple.c as is, the issue persisted.

Regards,
  Vicenç.


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: kexec on rk3399
  2019-08-14 13:12   ` Robin Murphy
@ 2019-08-15  1:15     ` Vicente Bergas
  2019-08-15  6:06       ` Felipe Balbi
  0 siblings, 1 reply; 18+ messages in thread
From: Vicente Bergas @ 2019-08-15  1:15 UTC (permalink / raw)
  To: Robin Murphy, Felipe Balbi
  Cc: Heiko Stuebner, Will Deacon, Marc Zyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip, linux-kernel

On Wednesday, August 14, 2019 3:12:26 PM CEST, Robin Murphy wrote:
> On 14/08/2019 13:53, Vicente Bergas wrote:
>> On Monday, July 22, 2019 4:31:27 PM CEST, Vicente Bergas wrote: ...
>
> This particular change looks like it's implicitly specific to 
> RK3399, which wouldn't be ideal. Presumably if the core dwc3 
> driver implemented shutdown correctly (echoing parts of 
> dwc3_remove(), I guess) then the glue layers shouldn't need 
> anything special anyway.
>
> Robin.

I just checked simple->resets from dwc3-of-simple.c and it is an array
with multiple resets whereas dwc->reset from core.c is NULL.
So the reset seems specific to the glue layers.
Is there another way than resetting the thing that is
generic enough to go to core.c and allows kexec?

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: kexec on rk3399
  2019-08-14 13:15     ` Vicente Bergas
@ 2019-08-15  6:00       ` Felipe Balbi
  0 siblings, 0 replies; 18+ messages in thread
From: Felipe Balbi @ 2019-08-15  6:00 UTC (permalink / raw)
  To: Vicente Bergas
  Cc: Robin Murphy, Heiko Stuebner, Will Deacon, Marc Zyngier,
	Catalin Marinas, Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip, linux-kernel


Hi,

Vicente Bergas <vicencb@gmail.com> writes:
>> Vicente Bergas <vicencb@gmail.com> writes:
>>> On Monday, July 22, 2019 4:31:27 PM CEST, Vicente Bergas wrote:
>>>> Hi, i have been running linux on rk3399 booted with kexec fine until 5.2
>>>> From 5.2 onwards, there are memory corruption issues as reported here:
>>>> http://lkml.iu.edu/hypermail/linux/kernel/1906.2/07211.html
>>>> kexec has been identified as the principal reason for the issues.
>>>> 
>>>> It turns out that kexec has never worked reliably on this platform, ...
>>> 
>>> Thank you all for your suggestions on where the issue could be.
>>> 
>>> It seems that it was the USB driver.
>>> Now using v5.2.8 booted with kexec from v5.2.8 with a workaround and
>>> so far so good. It is being tested on the Sapphire board.
>>> 
>>> The workaround is:
>>> --- a/drivers/usb/dwc3/dwc3-of-simple.c
>>> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
>>> @@ -133,6 +133,13 @@
>>>  	return 0;
>>>  }
>>>  
>>> +static void dwc3_of_simple_shutdown(struct platform_device *pdev)
>>> +{
>>> +	struct dwc3_of_simple *simple = platform_get_drvdata(pdev);
>>> +
>>> +	reset_control_assert(simple->resets);
>>> +}
>>> +
>>>  static int __maybe_unused dwc3_of_simple_runtime_suspend(struct device 
>>> *dev)
>>>  {
>>>  	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
>>> @@ -190,6 +197,7 @@
>>>  static struct platform_driver dwc3_of_simple_driver = {
>>>  	.probe		= dwc3_of_simple_probe,
>>>  	.remove		= dwc3_of_simple_remove,
>>> +	.shutdown	= dwc3_of_simple_shutdown,
>>>  	.driver		= {
>>>  		.name	= "dwc3-of-simple",
>>>  		.of_match_table = of_dwc3_simple_match,
>>> 
>>> If this patch is OK after review i can resubmit it as a pull request.
>>
>> not a pull request, just send a patch using git send-email
>>
>>> Should a similar change be applied to drivers/usb/dwc3/core.c ?
>>
>> Is it necessary? We haven't had any bug reports regarding that. Also, if
>> we have reset control support in the core driver, why do we need it in
>> of_simple? Seems like of_simple could just rely on what core does.
>
> the workaround has been tested patching only core.c with
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -1561,6 +1561,13 @@
>  	return 0;
>  }
>  
> +static void dwc3_shutdown(struct platform_device *pdev)
> +{
> +	struct dwc3 *dwc = platform_get_drvdata(pdev);
> +
> +	reset_control_assert(dwc->reset);
> +}
> +
>  #ifdef CONFIG_PM
>  static int dwc3_core_init_for_resume(struct dwc3 *dwc)
>  {
> @@ -1866,6 +1873,7 @@
>  static struct platform_driver dwc3_driver = {
>  	.probe		= dwc3_probe,
>  	.remove		= dwc3_remove,
> +	.shutdown	= dwc3_shutdown,
>  	.driver		= {
>  		.name	= "dwc3",
>  		.of_match_table	= of_match_ptr(of_dwc3_match),
>
> and leaving dwc3-of-simple.c as is, the issue persisted.

That's because your reset controller is not passed to dwc3 core, only to
your glue layer.

-- 
balbi

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: kexec on rk3399
  2019-08-15  1:15     ` Vicente Bergas
@ 2019-08-15  6:06       ` Felipe Balbi
  2019-08-15 11:09         ` Robin Murphy
  0 siblings, 1 reply; 18+ messages in thread
From: Felipe Balbi @ 2019-08-15  6:06 UTC (permalink / raw)
  To: Vicente Bergas, Robin Murphy
  Cc: Heiko Stuebner, Will Deacon, Marc Zyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip, linux-kernel


Hi,

Vicente Bergas <vicencb@gmail.com> writes:

> On Wednesday, August 14, 2019 3:12:26 PM CEST, Robin Murphy wrote:
>> On 14/08/2019 13:53, Vicente Bergas wrote:
>>> On Monday, July 22, 2019 4:31:27 PM CEST, Vicente Bergas wrote: ...
>>
>> This particular change looks like it's implicitly specific to 
>> RK3399, which wouldn't be ideal. Presumably if the core dwc3 
>> driver implemented shutdown correctly (echoing parts of 
>> dwc3_remove(), I guess) then the glue layers shouldn't need 
>> anything special anyway.
>>
>> Robin.
>
> I just checked simple->resets from dwc3-of-simple.c and it is an array
> with multiple resets whereas dwc->reset from core.c is NULL.
> So the reset seems specific to the glue layers.
> Is there another way than resetting the thing that is
> generic enough to go to core.c and allows kexec?

This is a really odd 'failure'. We do full soft reset during driver
initialization on dwc3. We shouldn't need to assert reset on shutdown,
really.

I think the problem is here:

	if (simple->pulse_resets) {
		ret = reset_control_reset(simple->resets);
		if (ret)
			goto err_resetc_put;
	} else {
		ret = reset_control_deassert(simple->resets);
		if (ret)
			goto err_resetc_put;
	}

Note that if pulse_resets is set, we will run a reset. But if
pulse_resets is false and need_reset is true, we deassert the reset.

I think below patch is enough:

diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-simple.c
index bdac3e7d7b18..9a2f3e09aa2e 100644
--- a/drivers/usb/dwc3/dwc3-of-simple.c
+++ b/drivers/usb/dwc3/dwc3-of-simple.c
@@ -72,7 +72,15 @@ static int dwc3_of_simple_probe(struct platform_device *pdev)
 		ret = reset_control_reset(simple->resets);
 		if (ret)
 			goto err_resetc_put;
-	} else {
+	}
+
+	if (simple->need_reset) {
+		ret = reset_control_assert(simple->resets);
+		if (ret)
+			goto err_resetc_put;
+
+		usleep_range(1000, 2000);
+
 		ret = reset_control_deassert(simple->resets);
 		if (ret)
 			goto err_resetc_put;
@@ -121,9 +129,6 @@ static int dwc3_of_simple_remove(struct platform_device *pdev)
 	clk_bulk_put_all(simple->num_clocks, simple->clks);
 	simple->num_clocks = 0;
 
-	if (!simple->pulse_resets)
-		reset_control_assert(simple->resets);
-
 	reset_control_put(simple->resets);
 
 	pm_runtime_disable(dev);

Can you test?

-- 
balbi

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: kexec on rk3399
  2019-08-15  6:06       ` Felipe Balbi
@ 2019-08-15 11:09         ` Robin Murphy
  2019-08-17 17:41           ` [PATCH] usb: dwc3: Add shutdown to platform_driver Vicente Bergas
  0 siblings, 1 reply; 18+ messages in thread
From: Robin Murphy @ 2019-08-15 11:09 UTC (permalink / raw)
  To: Felipe Balbi, Vicente Bergas
  Cc: Heiko Stuebner, Will Deacon, Marc Zyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip, linux-kernel

On 15/08/2019 07:06, Felipe Balbi wrote:
> 
> Hi,
> 
> Vicente Bergas <vicencb@gmail.com> writes:
> 
>> On Wednesday, August 14, 2019 3:12:26 PM CEST, Robin Murphy wrote:
>>> On 14/08/2019 13:53, Vicente Bergas wrote:
>>>> On Monday, July 22, 2019 4:31:27 PM CEST, Vicente Bergas wrote: ...
>>>
>>> This particular change looks like it's implicitly specific to
>>> RK3399, which wouldn't be ideal. Presumably if the core dwc3
>>> driver implemented shutdown correctly (echoing parts of
>>> dwc3_remove(), I guess) then the glue layers shouldn't need
>>> anything special anyway.
>>>
>>> Robin.
>>
>> I just checked simple->resets from dwc3-of-simple.c and it is an array
>> with multiple resets whereas dwc->reset from core.c is NULL.
>> So the reset seems specific to the glue layers.
>> Is there another way than resetting the thing that is
>> generic enough to go to core.c and allows kexec?
> 
> This is a really odd 'failure'. We do full soft reset during driver
> initialization on dwc3. We shouldn't need to assert reset on shutdown,
> really.

Probing/initialisation has never been the problem. The issue for the 
kexec case is that when the first kernel shuts down, there is currently 
nothing to quiesce the controller (since only driver->shutdown gets 
called, not driver->remove), and thus (presumably) external USB activity 
causes it to keep writing back over the memory where the 
descriptors/command ring used to be while the second kernel boots. The 
second kernel will eventually probe and reset it appropriately, but by 
that time the damage is already done.

Yanking on a hardware reset line when the first kernel shuts down is 
certainly one way to stop any memory accesses if such a control is 
available, but presumably there's a general software way to gracefully 
disable the controller's DMA functions until a subsequent probe can 
fully reset it again - I think that would be the preferable solution.

Robin.

> I think the problem is here:
> 
> 	if (simple->pulse_resets) {
> 		ret = reset_control_reset(simple->resets);
> 		if (ret)
> 			goto err_resetc_put;
> 	} else {
> 		ret = reset_control_deassert(simple->resets);
> 		if (ret)
> 			goto err_resetc_put;
> 	}
> 
> Note that if pulse_resets is set, we will run a reset. But if
> pulse_resets is false and need_reset is true, we deassert the reset.
> 
> I think below patch is enough:
> 
> diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-simple.c
> index bdac3e7d7b18..9a2f3e09aa2e 100644
> --- a/drivers/usb/dwc3/dwc3-of-simple.c
> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
> @@ -72,7 +72,15 @@ static int dwc3_of_simple_probe(struct platform_device *pdev)
>   		ret = reset_control_reset(simple->resets);
>   		if (ret)
>   			goto err_resetc_put;
> -	} else {
> +	}
> +
> +	if (simple->need_reset) {
> +		ret = reset_control_assert(simple->resets);
> +		if (ret)
> +			goto err_resetc_put;
> +
> +		usleep_range(1000, 2000);
> +
>   		ret = reset_control_deassert(simple->resets);
>   		if (ret)
>   			goto err_resetc_put;
> @@ -121,9 +129,6 @@ static int dwc3_of_simple_remove(struct platform_device *pdev)
>   	clk_bulk_put_all(simple->num_clocks, simple->clks);
>   	simple->num_clocks = 0;
>   
> -	if (!simple->pulse_resets)
> -		reset_control_assert(simple->resets);
> -
>   	reset_control_put(simple->resets);
>   
>   	pm_runtime_disable(dev);
> 
> Can you test?
> 

^ permalink raw reply	[flat|nested] 18+ messages in thread

* [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-08-15 11:09         ` Robin Murphy
@ 2019-08-17 17:41           ` Vicente Bergas
  2019-08-27 11:45             ` Vicente Bergas
  2019-09-19 11:36             ` Vicente Bergas
  0 siblings, 2 replies; 18+ messages in thread
From: Vicente Bergas @ 2019-08-17 17:41 UTC (permalink / raw)
  To: Felipe Balbi, Robin Murphy
  Cc: Heiko Stuebner, Will Deacon, MarcZyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip, Vicente Bergas

Otherwise the device keeps writing to memory after kexec and disturbs
the next kernel.

Signed-off-by: Vicente Bergas <vicencb@gmail.com>
---
 drivers/usb/dwc3/dwc3-of-simple.c | 6 ++++++
 1 file changed, 6 insertions(+)

Hi Felipe, Robin,
this version calls 'remove' from 'shutdown' instead of just asserting
a reset because it looks like a cleaner way to stop the device.

Calling remove from shutdown in core.c instead of dwc3-of-simple.c does not
fix the issue either.

It has been tested on the sapphire board, a RK3399 platform.

Regards,
  Vicenç.

diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-simple.c
index bdac3e7d7b18..d5fd45c64901 100644
--- a/drivers/usb/dwc3/dwc3-of-simple.c
+++ b/drivers/usb/dwc3/dwc3-of-simple.c
@@ -133,6 +133,11 @@ static int dwc3_of_simple_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static void dwc3_of_simple_shutdown(struct platform_device *pdev)
+{
+	dwc3_of_simple_remove(pdev);
+}
+
 static int __maybe_unused dwc3_of_simple_runtime_suspend(struct device *dev)
 {
 	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
@@ -190,6 +195,7 @@ MODULE_DEVICE_TABLE(of, of_dwc3_simple_match);
 static struct platform_driver dwc3_of_simple_driver = {
 	.probe		= dwc3_of_simple_probe,
 	.remove		= dwc3_of_simple_remove,
+	.shutdown	= dwc3_of_simple_shutdown,
 	.driver		= {
 		.name	= "dwc3-of-simple",
 		.of_match_table = of_dwc3_simple_match,
-- 
2.22.1


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-08-17 17:41           ` [PATCH] usb: dwc3: Add shutdown to platform_driver Vicente Bergas
@ 2019-08-27 11:45             ` Vicente Bergas
  2019-08-27 11:53               ` Felipe Balbi
  2019-09-19 11:36             ` Vicente Bergas
  1 sibling, 1 reply; 18+ messages in thread
From: Vicente Bergas @ 2019-08-27 11:45 UTC (permalink / raw)
  To: Felipe Balbi, Robin Murphy
  Cc: Heiko Stuebner, Will Deacon, MarcZyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip

On Saturday, August 17, 2019 7:41:40 PM CEST, Vicente Bergas wrote:
> Otherwise the device keeps writing to memory after kexec and disturbs
> the next kernel.
>
> Signed-off-by: Vicente Bergas <vicencb@gmail.com>
> ---
>  drivers/usb/dwc3/dwc3-of-simple.c | 6 ++++++
>  1 file changed, 6 insertions(+)
>
> Hi Felipe, Robin,
> this version calls 'remove' from 'shutdown' instead of just asserting
> a reset because it looks like a cleaner way to stop the device.
>
> Calling remove from shutdown in core.c instead of dwc3-of-simple.c does not
> fix the issue either.
>
> It has been tested on the sapphire board, a RK3399 platform.
>
> Regards,
>   Vicenç.
>
> diff --git a/drivers/usb/dwc3/dwc3-of-simple.c 
> b/drivers/usb/dwc3/dwc3-of-simple.c
> index bdac3e7d7b18..d5fd45c64901 100644
> --- a/drivers/usb/dwc3/dwc3-of-simple.c
> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
> @@ -133,6 +133,11 @@ static int dwc3_of_simple_remove(struct 
> platform_device *pdev)
>  	return 0;
>  }
>  
> +static void dwc3_of_simple_shutdown(struct platform_device *pdev)
> +{
> +	dwc3_of_simple_remove(pdev);
> +}
> +
>  static int __maybe_unused 
> dwc3_of_simple_runtime_suspend(struct device *dev)
>  {
>  	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
> @@ -190,6 +195,7 @@ MODULE_DEVICE_TABLE(of, of_dwc3_simple_match);
>  static struct platform_driver dwc3_of_simple_driver = {
>  	.probe		= dwc3_of_simple_probe,
>  	.remove		= dwc3_of_simple_remove,
> +	.shutdown	= dwc3_of_simple_shutdown,
>  	.driver		= {
>  		.name	= "dwc3-of-simple",
>  		.of_match_table = of_dwc3_simple_match,

Hi,
please, can you provide some feedback on this?

Regards,
  Vicenç.


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-08-27 11:45             ` Vicente Bergas
@ 2019-08-27 11:53               ` Felipe Balbi
  2019-08-27 12:16                 ` Vicente Bergas
  0 siblings, 1 reply; 18+ messages in thread
From: Felipe Balbi @ 2019-08-27 11:53 UTC (permalink / raw)
  To: Vicente Bergas, Robin Murphy
  Cc: Heiko Stuebner, Will Deacon, MarcZyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip

[-- Attachment #1: Type: text/plain, Size: 1852 bytes --]


Hi,

Vicente Bergas <vicencb@gmail.com> writes:
> On Saturday, August 17, 2019 7:41:40 PM CEST, Vicente Bergas wrote:
>> Otherwise the device keeps writing to memory after kexec and disturbs
>> the next kernel.
>>
>> Signed-off-by: Vicente Bergas <vicencb@gmail.com>
>> ---
>>  drivers/usb/dwc3/dwc3-of-simple.c | 6 ++++++
>>  1 file changed, 6 insertions(+)
>>
>> Hi Felipe, Robin,
>> this version calls 'remove' from 'shutdown' instead of just asserting
>> a reset because it looks like a cleaner way to stop the device.
>>
>> Calling remove from shutdown in core.c instead of dwc3-of-simple.c does not
>> fix the issue either.
>>
>> It has been tested on the sapphire board, a RK3399 platform.
>>
>> Regards,
>>   Vicenç.
>>
>> diff --git a/drivers/usb/dwc3/dwc3-of-simple.c 
>> b/drivers/usb/dwc3/dwc3-of-simple.c
>> index bdac3e7d7b18..d5fd45c64901 100644
>> --- a/drivers/usb/dwc3/dwc3-of-simple.c
>> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
>> @@ -133,6 +133,11 @@ static int dwc3_of_simple_remove(struct 
>> platform_device *pdev)
>>  	return 0;
>>  }
>>  
>> +static void dwc3_of_simple_shutdown(struct platform_device *pdev)
>> +{
>> +	dwc3_of_simple_remove(pdev);
>> +}
>> +
>>  static int __maybe_unused 
>> dwc3_of_simple_runtime_suspend(struct device *dev)
>>  {
>>  	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
>> @@ -190,6 +195,7 @@ MODULE_DEVICE_TABLE(of, of_dwc3_simple_match);
>>  static struct platform_driver dwc3_of_simple_driver = {
>>  	.probe		= dwc3_of_simple_probe,
>>  	.remove		= dwc3_of_simple_remove,
>> +	.shutdown	= dwc3_of_simple_shutdown,

why don't you just have shutdown use the same exact function as remove?
Frankly, though, I still don't fully understand what's going wrong
here. Why is the device still alive during kexec?

cheers

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-08-27 11:53               ` Felipe Balbi
@ 2019-08-27 12:16                 ` Vicente Bergas
  2019-09-09 15:07                   ` Vicente Bergas
  0 siblings, 1 reply; 18+ messages in thread
From: Vicente Bergas @ 2019-08-27 12:16 UTC (permalink / raw)
  To: Felipe Balbi
  Cc: Robin Murphy, Heiko Stuebner, Will Deacon, MarcZyngier,
	Catalin Marinas, Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip

On Tuesday, August 27, 2019 1:53:04 PM CEST, Felipe Balbi wrote:
> Hi,
>
> Vicente Bergas <vicencb@gmail.com> writes:
>> On Saturday, August 17, 2019 7:41:40 PM CEST, Vicente Bergas wrote:
>>> Otherwise the device keeps writing to memory after kexec and disturbs
>>> the next kernel.
...
>
> why don't you just have shutdown use the same exact function as remove?
> Frankly, though, I still don't fully understand what's going wrong
> here. Why is the device still alive during kexec?
>
> cheers

Hi Felipe,
the remove and shutdown functions have different prototypes, so
shutdown is wrapping remove.
Would it be preferable to cast remove as shutdown?

The issue with kexec is that the device is being used during the livetime
of the first kernel. When the first kernel executes kexec it calls the
shutdown function of drivers (instead of remove). Because of this the dwc3
device keeps doing things like DMA.
While the second kernel is taking over, it gets its memory corrupted with
such DMA accesses from the device. When the second kernel reaches the point
of taking over the dwc3 device, re-initializes it, but it is already too
late. Still worse, if the second kernel did not have the dwc3 driver, it
would get endless memory corruptions.
All in all, devices that can do DMA need to stop doing it on shutdown.

Regards,
  Vicenç.


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-08-27 12:16                 ` Vicente Bergas
@ 2019-09-09 15:07                   ` Vicente Bergas
  2019-10-23  6:31                     ` Felipe Balbi
  0 siblings, 1 reply; 18+ messages in thread
From: Vicente Bergas @ 2019-09-09 15:07 UTC (permalink / raw)
  To: Felipe Balbi, Robin Murphy
  Cc: Heiko Stuebner, Will Deacon, MarcZyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip

On Tuesday, August 27, 2019 2:16:20 PM CEST, Vicente Bergas wrote:
> On Tuesday, August 27, 2019 1:53:04 PM CEST, Felipe Balbi wrote:
>> Hi,
>> 
>> Vicente Bergas <vicencb@gmail.com> writes:
>>> On Saturday, August 17, 2019 7:41:40 PM CEST, Vicente Bergas wrote:
>>>> Otherwise the device keeps writing to memory after kexec and disturbs
>>>> the next kernel.
> ...
>> 
>> why don't you just have shutdown use the same exact function as remove?
>> Frankly, though, I still don't fully understand what's going wrong
>> here. Why is the device still alive during kexec?
>> 
>> cheers
>
> Hi Felipe,
> the remove and shutdown functions have different prototypes, so
> shutdown is wrapping remove.
> Would it be preferable to cast remove as shutdown?
>
> The issue with kexec is that the device is being used during the livetime
> of the first kernel. When the first kernel executes kexec it calls the
> shutdown function of drivers (instead of remove). Because of this the dwc3
> device keeps doing things like DMA.
> While the second kernel is taking over, it gets its memory corrupted with
> such DMA accesses from the device. When the second kernel reaches the point
> of taking over the dwc3 device, re-initializes it, but it is already too
> late. Still worse, if the second kernel did not have the dwc3 driver, it
> would get endless memory corruptions.
> All in all, devices that can do DMA need to stop doing it on shutdown.
>
> Regards,
>  Vicenç.

Hi,
please, can you provide some feedback on this?

Regards,
 Vicenç.

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-08-17 17:41           ` [PATCH] usb: dwc3: Add shutdown to platform_driver Vicente Bergas
  2019-08-27 11:45             ` Vicente Bergas
@ 2019-09-19 11:36             ` Vicente Bergas
  1 sibling, 0 replies; 18+ messages in thread
From: Vicente Bergas @ 2019-09-19 11:36 UTC (permalink / raw)
  To: Felipe Balbi
  Cc: Robin Murphy, Heiko Stuebner, Will Deacon, MarcZyngier,
	Catalin Marinas, Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip

Ping?

On Saturday, August 17, 2019 7:41:40 PM CEST, Vicente Bergas wrote:
> Otherwise the device keeps writing to memory after kexec and disturbs
> the next kernel.
>
> Signed-off-by: Vicente Bergas <vicencb@gmail.com>
> ---
>  drivers/usb/dwc3/dwc3-of-simple.c | 6 ++++++
>  1 file changed, 6 insertions(+)
>
> Hi Felipe, Robin,
> this version calls 'remove' from 'shutdown' instead of just asserting
> a reset because it looks like a cleaner way to stop the device.
>
> Calling remove from shutdown in core.c instead of dwc3-of-simple.c does not
> fix the issue either.
>
> It has been tested on the sapphire board, a RK3399 platform.
>
> Regards,
>   Vicenç.
>
> diff --git a/drivers/usb/dwc3/dwc3-of-simple.c 
> b/drivers/usb/dwc3/dwc3-of-simple.c
> index bdac3e7d7b18..d5fd45c64901 100644
> --- a/drivers/usb/dwc3/dwc3-of-simple.c
> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
> @@ -133,6 +133,11 @@ static int dwc3_of_simple_remove(struct 
> platform_device *pdev)
>  	return 0;
>  }
>  
> +static void dwc3_of_simple_shutdown(struct platform_device *pdev)
> +{
> +	dwc3_of_simple_remove(pdev);
> +}
> +
>  static int __maybe_unused 
> dwc3_of_simple_runtime_suspend(struct device *dev)
>  {
>  	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
> @@ -190,6 +195,7 @@ MODULE_DEVICE_TABLE(of, of_dwc3_simple_match);
>  static struct platform_driver dwc3_of_simple_driver = {
>  	.probe		= dwc3_of_simple_probe,
>  	.remove		= dwc3_of_simple_remove,
> +	.shutdown	= dwc3_of_simple_shutdown,
>  	.driver		= {
>  		.name	= "dwc3-of-simple",
>  		.of_match_table = of_dwc3_simple_match,


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-09-09 15:07                   ` Vicente Bergas
@ 2019-10-23  6:31                     ` Felipe Balbi
  2019-10-24 12:15                       ` Vicente Bergas
  0 siblings, 1 reply; 18+ messages in thread
From: Felipe Balbi @ 2019-10-23  6:31 UTC (permalink / raw)
  To: Vicente Bergas, Robin Murphy
  Cc: Heiko Stuebner, Will Deacon, MarcZyngier, Catalin Marinas,
	Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip

[-- Attachment #1: Type: text/plain, Size: 3709 bytes --]


Hi,

(sorry for the long delay)

Vicente Bergas <vicencb@gmail.com> writes:

> On Tuesday, August 27, 2019 2:16:20 PM CEST, Vicente Bergas wrote:
>> On Tuesday, August 27, 2019 1:53:04 PM CEST, Felipe Balbi wrote:
>>> Hi,
>>> 
>>> Vicente Bergas <vicencb@gmail.com> writes:
>>>> On Saturday, August 17, 2019 7:41:40 PM CEST, Vicente Bergas wrote:
>>>>> Otherwise the device keeps writing to memory after kexec and disturbs
>>>>> the next kernel.
>> ...
>>> 
>>> why don't you just have shutdown use the same exact function as remove?
>>> Frankly, though, I still don't fully understand what's going wrong
>>> here. Why is the device still alive during kexec?
>>> 
>>> cheers
>>
>> Hi Felipe,
>> the remove and shutdown functions have different prototypes, so
>> shutdown is wrapping remove.
>> Would it be preferable to cast remove as shutdown?
>>
>> The issue with kexec is that the device is being used during the livetime
>> of the first kernel. When the first kernel executes kexec it calls the
>> shutdown function of drivers (instead of remove). Because of this the dwc3
>> device keeps doing things like DMA.
>> While the second kernel is taking over, it gets its memory corrupted with
>> such DMA accesses from the device. When the second kernel reaches the point
>> of taking over the dwc3 device, re-initializes it, but it is already too
>> late. Still worse, if the second kernel did not have the dwc3 driver, it
>> would get endless memory corruptions.
>> All in all, devices that can do DMA need to stop doing it on shutdown.
>>
>> Regards,
>>  Vicenç.
>
> Hi,
> please, can you provide some feedback on this?

I meant something like this:

diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-of-simple.c
index bdac3e7d7b18..e64754be47b4 100644
--- a/drivers/usb/dwc3/dwc3-of-simple.c
+++ b/drivers/usb/dwc3/dwc3-of-simple.c
@@ -110,12 +110,9 @@ static int dwc3_of_simple_probe(struct platform_device *pdev)
 	return ret;
 }
 
-static int dwc3_of_simple_remove(struct platform_device *pdev)
+static void __dwc3_of_simple_teardown(struct dwc3_of_simple *simple)
 {
-	struct dwc3_of_simple	*simple = platform_get_drvdata(pdev);
-	struct device		*dev = &pdev->dev;
-
-	of_platform_depopulate(dev);
+	of_platform_depopulate(simple->dev);
 
 	clk_bulk_disable_unprepare(simple->num_clocks, simple->clks);
 	clk_bulk_put_all(simple->num_clocks, simple->clks);
@@ -126,13 +123,27 @@ static int dwc3_of_simple_remove(struct platform_device *pdev)
 
 	reset_control_put(simple->resets);
 
-	pm_runtime_disable(dev);
-	pm_runtime_put_noidle(dev);
-	pm_runtime_set_suspended(dev);
+	pm_runtime_disable(simple->dev);
+	pm_runtime_put_noidle(simple->dev);
+	pm_runtime_set_suspended(simple->dev);
+}
+
+static int dwc3_of_simple_remove(struct platform_device *pdev)
+{
+	struct dwc3_of_simple	*simple = platform_get_drvdata(pdev);
+
+	__dwc3_of_simple_teardown(simple);
 
 	return 0;
 }
 
+static void dwc3_of_simple_shutdown(struct platform_device *pdev)
+{
+	struct dwc3_of_simple	*simple = platform_get_drvdata(pdev);
+
+	__dwc3_of_simple_teardown(simple);
+}
+
 static int __maybe_unused dwc3_of_simple_runtime_suspend(struct device *dev)
 {
 	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
@@ -190,6 +201,7 @@ MODULE_DEVICE_TABLE(of, of_dwc3_simple_match);
 static struct platform_driver dwc3_of_simple_driver = {
 	.probe		= dwc3_of_simple_probe,
 	.remove		= dwc3_of_simple_remove,
+	.shutdown	= dwc3_of_simple_shutdown,
 	.driver		= {
 		.name	= "dwc3-of-simple",
 		.of_match_table = of_dwc3_simple_match,

Can you make sure it works as you intended?

-- 
balbi

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 832 bytes --]

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-10-23  6:31                     ` Felipe Balbi
@ 2019-10-24 12:15                       ` Vicente Bergas
  2019-10-25 10:25                         ` Felipe Balbi
  0 siblings, 1 reply; 18+ messages in thread
From: Vicente Bergas @ 2019-10-24 12:15 UTC (permalink / raw)
  To: Felipe Balbi
  Cc: Robin Murphy, Heiko Stuebner, Will Deacon, MarcZyngier,
	Catalin Marinas, Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip

On Wednesday, October 23, 2019 8:31:21 AM CEST, Felipe Balbi wrote:
> Hi,
>
> (sorry for the long delay)
>
> Vicente Bergas <vicencb@gmail.com> writes:
>
>> On Tuesday, August 27, 2019 2:16:20 PM CEST, Vicente Bergas wrote: ...
>
> I meant something like this:
>
> diff --git a/drivers/usb/dwc3/dwc3-of-simple.c 
> b/drivers/usb/dwc3/dwc3-of-simple.c
> index bdac3e7d7b18..e64754be47b4 100644
> --- a/drivers/usb/dwc3/dwc3-of-simple.c
> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
> @@ -110,12 +110,9 @@ static int dwc3_of_simple_probe(struct 
> platform_device *pdev)
>  	return ret;
>  }
>  
> -static int dwc3_of_simple_remove(struct platform_device *pdev)
> +static void __dwc3_of_simple_teardown(struct dwc3_of_simple *simple)
>  {
> -	struct dwc3_of_simple	*simple = platform_get_drvdata(pdev);
> -	struct device		*dev = &pdev->dev;
> -
> -	of_platform_depopulate(dev);
> +	of_platform_depopulate(simple->dev);
>  
>  	clk_bulk_disable_unprepare(simple->num_clocks, simple->clks);
>  	clk_bulk_put_all(simple->num_clocks, simple->clks);
> @@ -126,13 +123,27 @@ static int dwc3_of_simple_remove(struct 
> platform_device *pdev)
>  
>  	reset_control_put(simple->resets);
>  
> -	pm_runtime_disable(dev);
> -	pm_runtime_put_noidle(dev);
> -	pm_runtime_set_suspended(dev);
> +	pm_runtime_disable(simple->dev);
> +	pm_runtime_put_noidle(simple->dev);
> +	pm_runtime_set_suspended(simple->dev);
> +}
> +
> +static int dwc3_of_simple_remove(struct platform_device *pdev)
> +{
> +	struct dwc3_of_simple	*simple = platform_get_drvdata(pdev);
> +
> +	__dwc3_of_simple_teardown(simple);
>  
>  	return 0;
>  }
>  
> +static void dwc3_of_simple_shutdown(struct platform_device *pdev)
> +{
> +	struct dwc3_of_simple	*simple = platform_get_drvdata(pdev);
> +
> +	__dwc3_of_simple_teardown(simple);
> +}
> +
>  static int __maybe_unused 
> dwc3_of_simple_runtime_suspend(struct device *dev)
>  {
>  	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
> @@ -190,6 +201,7 @@ MODULE_DEVICE_TABLE(of, of_dwc3_simple_match);
>  static struct platform_driver dwc3_of_simple_driver = {
>  	.probe		= dwc3_of_simple_probe,
>  	.remove		= dwc3_of_simple_remove,
> +	.shutdown	= dwc3_of_simple_shutdown,
>  	.driver		= {
>  		.name	= "dwc3-of-simple",
>  		.of_match_table = of_dwc3_simple_match,
>
> Can you make sure it works as you intended?

Hi Felipe,
just applied your approach to v5.3.7 and it is working properly.

Thanks,
  Vicente.


^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-10-24 12:15                       ` Vicente Bergas
@ 2019-10-25 10:25                         ` Felipe Balbi
  2019-10-25 10:42                           ` Vicente Bergas
  0 siblings, 1 reply; 18+ messages in thread
From: Felipe Balbi @ 2019-10-25 10:25 UTC (permalink / raw)
  To: Vicente Bergas
  Cc: Robin Murphy, Heiko Stuebner, Will Deacon, MarcZyngier,
	Catalin Marinas, Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip


hi,

Vicente Bergas <vicencb@gmail.com> writes:

> On Wednesday, October 23, 2019 8:31:21 AM CEST, Felipe Balbi wrote:
>> Hi,
>>
>> (sorry for the long delay)
>>
>> Vicente Bergas <vicencb@gmail.com> writes:
>>
>>> On Tuesday, August 27, 2019 2:16:20 PM CEST, Vicente Bergas wrote: ...
>>
>> I meant something like this:
>>
>> diff --git a/drivers/usb/dwc3/dwc3-of-simple.c 
>> b/drivers/usb/dwc3/dwc3-of-simple.c
>> index bdac3e7d7b18..e64754be47b4 100644
>> --- a/drivers/usb/dwc3/dwc3-of-simple.c
>> +++ b/drivers/usb/dwc3/dwc3-of-simple.c
>> @@ -110,12 +110,9 @@ static int dwc3_of_simple_probe(struct 
>> platform_device *pdev)
>>  	return ret;
>>  }
>>  
>> -static int dwc3_of_simple_remove(struct platform_device *pdev)
>> +static void __dwc3_of_simple_teardown(struct dwc3_of_simple *simple)
>>  {
>> -	struct dwc3_of_simple	*simple = platform_get_drvdata(pdev);
>> -	struct device		*dev = &pdev->dev;
>> -
>> -	of_platform_depopulate(dev);
>> +	of_platform_depopulate(simple->dev);
>>  
>>  	clk_bulk_disable_unprepare(simple->num_clocks, simple->clks);
>>  	clk_bulk_put_all(simple->num_clocks, simple->clks);
>> @@ -126,13 +123,27 @@ static int dwc3_of_simple_remove(struct 
>> platform_device *pdev)
>>  
>>  	reset_control_put(simple->resets);
>>  
>> -	pm_runtime_disable(dev);
>> -	pm_runtime_put_noidle(dev);
>> -	pm_runtime_set_suspended(dev);
>> +	pm_runtime_disable(simple->dev);
>> +	pm_runtime_put_noidle(simple->dev);
>> +	pm_runtime_set_suspended(simple->dev);
>> +}
>> +
>> +static int dwc3_of_simple_remove(struct platform_device *pdev)
>> +{
>> +	struct dwc3_of_simple	*simple = platform_get_drvdata(pdev);
>> +
>> +	__dwc3_of_simple_teardown(simple);
>>  
>>  	return 0;
>>  }
>>  
>> +static void dwc3_of_simple_shutdown(struct platform_device *pdev)
>> +{
>> +	struct dwc3_of_simple	*simple = platform_get_drvdata(pdev);
>> +
>> +	__dwc3_of_simple_teardown(simple);
>> +}
>> +
>>  static int __maybe_unused 
>> dwc3_of_simple_runtime_suspend(struct device *dev)
>>  {
>>  	struct dwc3_of_simple	*simple = dev_get_drvdata(dev);
>> @@ -190,6 +201,7 @@ MODULE_DEVICE_TABLE(of, of_dwc3_simple_match);
>>  static struct platform_driver dwc3_of_simple_driver = {
>>  	.probe		= dwc3_of_simple_probe,
>>  	.remove		= dwc3_of_simple_remove,
>> +	.shutdown	= dwc3_of_simple_shutdown,
>>  	.driver		= {
>>  		.name	= "dwc3-of-simple",
>>  		.of_match_table = of_dwc3_simple_match,
>>
>> Can you make sure it works as you intended?
>
> Hi Felipe,
> just applied your approach to v5.3.7 and it is working properly.

Do you want to send it as a formal patch or shall I do it?

-- 
balbi

^ permalink raw reply	[flat|nested] 18+ messages in thread

* Re: [PATCH] usb: dwc3: Add shutdown to platform_driver
  2019-10-25 10:25                         ` Felipe Balbi
@ 2019-10-25 10:42                           ` Vicente Bergas
  0 siblings, 0 replies; 18+ messages in thread
From: Vicente Bergas @ 2019-10-25 10:42 UTC (permalink / raw)
  To: Felipe Balbi
  Cc: Robin Murphy, Heiko Stuebner, Will Deacon, MarcZyngier,
	Catalin Marinas, Matthias Brugger, Greg Kroah-Hartman, linux-usb,
	linux-arm-kernel, linux-rockchip

On Friday, October 25, 2019 12:25:17 PM CEST, Felipe Balbi wrote:
> hi,
>
> Vicente Bergas <vicencb@gmail.com> writes:
>
>> On Wednesday, October 23, 2019 8:31:21 AM CEST, Felipe Balbi wrote: ...
>
> Do you want to send it as a formal patch or shall I do it?

All yours. Thank you for reviewing and proposing this solution.

Regards,
  Vicente.


^ permalink raw reply	[flat|nested] 18+ messages in thread

end of thread, back to index

Thread overview: 18+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
     [not found] <ebcb52be-2063-4e2c-9a09-fdcacb94f855@gmail.com>
2019-08-14 12:53 ` kexec on rk3399 Vicente Bergas
2019-08-14 13:06   ` Felipe Balbi
2019-08-14 13:15     ` Vicente Bergas
2019-08-15  6:00       ` Felipe Balbi
2019-08-14 13:12   ` Robin Murphy
2019-08-15  1:15     ` Vicente Bergas
2019-08-15  6:06       ` Felipe Balbi
2019-08-15 11:09         ` Robin Murphy
2019-08-17 17:41           ` [PATCH] usb: dwc3: Add shutdown to platform_driver Vicente Bergas
2019-08-27 11:45             ` Vicente Bergas
2019-08-27 11:53               ` Felipe Balbi
2019-08-27 12:16                 ` Vicente Bergas
2019-09-09 15:07                   ` Vicente Bergas
2019-10-23  6:31                     ` Felipe Balbi
2019-10-24 12:15                       ` Vicente Bergas
2019-10-25 10:25                         ` Felipe Balbi
2019-10-25 10:42                           ` Vicente Bergas
2019-09-19 11:36             ` Vicente Bergas

Linux-USB Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-usb/0 linux-usb/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-usb linux-usb/ https://lore.kernel.org/linux-usb \
		linux-usb@vger.kernel.org
	public-inbox-index linux-usb

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-usb


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git