Linux-USB Archive on lore.kernel.org
 help / color / Atom feed
* USB DWC2 stops responding when insert/remove cable multiple times
@ 2020-02-14 13:40 Otavio Salvador
  2020-02-17  8:58 ` Minas Harutyunyan
  0 siblings, 1 reply; 11+ messages in thread
From: Otavio Salvador @ 2020-02-14 13:40 UTC (permalink / raw)
  To: Minas Harutyunyan, Greg Kroah-Hartman, linux-usb, Felipe Balbi,
	Heiko Stuebner, linux-rockchip, Johan Hovold

 the USB port stops responding. To recover the port we need to reload
the g_serial module.

I have reports of it happening in the field, on the device but, until
recently, it very hard to reproduce. We found that it is very easy to
reproduce when we use the Microsoft Surface Dock, as hub.

Description of the host:

    Operating System: Windows 10 Pro
    Driver: libusb-1.0 1.0.22

Description of the target:

    SoC: Rockchip RV1108G
    Gadget: g_serial
    Linux: 5.4.19

dmesg:

    [    0.000000] Booting Linux on physical CPU 0xf00
    [    0.000000] Linux version 5.4.19 (oe-user@oe-host) (gcc version
8.3.0 (GCC)) #1 SMP Thu Feb 13 20:45:28 UTC 2020
    [    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7),
cr=10c5387d
    [    0.005064] rcu: Hierarchical SRCU implementation.
    [    0.005746] smp: Bringing up secondary CPUs ...
    [    0.005774] smp: Brought up 1 node, 1 CPU
    [    0.005793] SMP: Total of 1 processors activated (48.00 BogoMIPS).
    [    0.005807] CPU: All CPU(s) started in SVC mode.
    [    0.006567] devtmpfs: initialized
    [    0.015073] VFP support v0.3: implementor 41 architecture 2
part 30 variant 7 rev 5
    [    0.015550] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 19112604462750000 ns
    [    0.015598] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
    [    0.015793] pinctrl core: initialized pinctrl subsystem
    [    0.017748] NET: Registered protocol family 16
    [    0.018265] DMA: preallocated 256 KiB pool for atomic coherent
allocations
    [    0.021331] cpuidle: using governor menu
    [    0.021896] Failed to find PMU node
    [    0.022081] hw-breakpoint: found 5 (+1 reserved) breakpoint and
4 watchpoint registers.
    [    0.022101] hw-breakpoint: maximum watchpoint size is 8 bytes.
    [    0.022469] Serial: AMBA PL011 UART driver
    [    0.071825] iommu: Default domain type: Translated
    [    0.073343] usbcore: registered new interface driver usbfs
    [    0.073455] usbcore: registered new interface driver hub
    [    0.073558] usbcore: registered new device driver usb
    [    0.074199] pps_core: LinuxPPS API ver. 1 registered
    [    0.074228] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
Rodolfo Giometti <giometti@linux.it>
    [    0.074281] PTP clock support registered
    [    0.077278] clocksource: Switched to clocksource arch_sys_counter
    [    0.872886] thermal_sys: Registered thermal governor 'step_wise'
    [    0.873716] NET: Registered protocol family 2
    [    0.874688] tcp_listen_portaddr_hash hash table entries: 512
(order: 0, 6144 bytes, linear)
    [    0.874747] TCP established hash table entries: 1024 (order: 0,
4096 bytes, linear)
    [    0.874793] TCP bind hash table entries: 1024 (order: 1, 8192
bytes, linear)
    [    0.874832] TCP: Hash tables configured (established 1024 bind 1024)
    [    0.874997] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
    [    0.875055] UDP-Lite hash table entries: 256 (order: 1, 8192
bytes, linear)
    [    0.875376] NET: Registered protocol family 1
    [    0.876470] RPC: Registered named UNIX socket transport module.
    [    0.876498] RPC: Registered udp transport module.
    [    0.876513] RPC: Registered tcp transport module.
    [    0.876527] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    0.877671] hw perfevents: enabled with armv7_cortex_a7 PMU
driver, 5 counters available
    [    0.880681] workingset: timestamp_bits=30 max_order=15 bucket_order=0
    [    0.893227] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    0.894966] NFS: Registering the id_resolver key type
    [    0.895040] Key type id_resolver registered
    [    0.895057] Key type id_legacy registered
    [    0.895155] ntfs: driver 2.1.32 [Flags: R/O].
    [    0.896438] Block layer SCSI generic (bsg) driver version 0.4
loaded (major 249)
    [    0.896470] io scheduler mq-deadline registered
    [    0.896487] io scheduler kyber registered
    [    0.904739] dma-pl330 102a0000.pdma: Loaded driver for PL330 DMAC-241330
    [    0.904778] dma-pl330 102a0000.pdma:         DBUFF-128x8bytes
Num_Chans-8 Num_Peri-20 Num_Events-16
    [    1.046331] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    [    1.051059] printk: console [ttyS2] disabled
    [    1.051192] 10210000.serial: ttyS2 at MMIO 0x10210000 (irq =
22, base_baud = 1500000) is a 16550A
    [    1.100239] printk: console [ttyS2] enabled
    [    1.103015] 10230000.serial: ttyS0 at MMIO 0x10230000 (irq =
23, base_baud = 1500000) is a 16550A
    [    1.105538] STMicroelectronics ASC driver initialized
    [    1.127141] brd: module loaded
    [    1.143433] loop: module loaded
    [    1.146411] libphy: Fixed MDIO Bus: probed
    [    1.149263] rk_gmac-dwmac 30200000.eth: IRQ eth_lpi not found
    [    1.150017] rk_gmac-dwmac 30200000.eth: PTP uses main clock
    [    1.150537] rk_gmac-dwmac 30200000.eth: no reset control found
    [    1.151100] rk_gmac-dwmac 30200000.eth: clock input or output? (output).
    [    1.151712] rk_gmac-dwmac 30200000.eth: Can not read property: tx_delay.
    [    1.152321] rk_gmac-dwmac 30200000.eth: set tx_delay to 0x30
    [    1.152834] rk_gmac-dwmac 30200000.eth: Can not read property: rx_delay.
    [    1.153434] rk_gmac-dwmac 30200000.eth: set rx_delay to 0x10
    [    1.153957] rk_gmac-dwmac 30200000.eth: integrated PHY? (no).
    [    1.154582] rk_gmac-dwmac 30200000.eth: cannot get clock clk_mac_speed
    [    1.160389] rk_gmac-dwmac 30200000.eth: init for RMII
    [    1.161278] rk_gmac-dwmac 30200000.eth: User ID: 0x10, Synopsys ID: 0x35
    [    1.161903] rk_gmac-dwmac 30200000.eth:      DWMAC1000
    [    1.162350] rk_gmac-dwmac 30200000.eth: DMA HW capability
register supported
    [    1.162988] rk_gmac-dwmac 30200000.eth: RX Checksum Offload
Engine supported
    [    1.163621] rk_gmac-dwmac 30200000.eth: COE Type 2
    [    1.164055] rk_gmac-dwmac 30200000.eth: TX Checksum insertion supported
    [    1.164647] rk_gmac-dwmac 30200000.eth: Wake-Up On Lan supported
    [    1.165261] rk_gmac-dwmac 30200000.eth: Normal descriptors
    [    1.165764] rk_gmac-dwmac 30200000.eth: Ring mode enabled
    [    1.166254] rk_gmac-dwmac 30200000.eth: Enable RX Mitigation
via HW Watchdog Timer
    [    1.166952] rk_gmac-dwmac 30200000.eth: device MAC address
1e:39:35:98:a1:87
    [    1.178781] libphy: stmmac: probed
    [    1.179133] Micrel KSZ886X Switch stmmac-0:01: attached PHY
driver [Micrel KSZ886X Switch] (mii_bus:phy_addr=stmmac-0:01,
irq=POLL)
    [    1.180193] Micrel KSZ886X Switch stmmac-0:02: attached PHY
driver [Micrel KSZ886X Switch] (mii_bus:phy_addr=stmmac-0:02,
irq=POLL)
    [    1.181245] Micrel KSZ886X Switch stmmac-0:03: attached PHY
driver [Micrel KSZ886X Switch] (mii_bus:phy_addr=stmmac-0:03,
irq=POLL)
    [    1.184175] PPP generic driver version 2.4.2
    [    1.184975] NET: Registered protocol family 24
    [    1.185589] usbcore: registered new interface driver asix
    [    1.186175] usbcore: registered new interface driver ax88179_178a
    [    1.186796] usbcore: registered new interface driver cdc_ether
    [    1.187547] usbcore: registered new interface driver net1080
    [    1.188148] usbcore: registered new interface driver cdc_subset
    [    1.188748] usbcore: registered new interface driver zaurus
    [    1.189387] usbcore: registered new interface driver cdc_ncm
    [    1.189969] usbcore: registered new interface driver qmi_wwan
    [    1.191575] dwc2 30180000.usb: 30180000.usb supply vusb_d not
found, using dummy regulator
    [    1.192497] dwc2 30180000.usb: 30180000.usb supply vusb_a not
found, using dummy regulator
    [    1.195816] dwc2 30180000.usb: Configuration mismatch. dr_mode
forced to device
    [    1.196585] dwc2 30180000.usb: dwc2_check_params: Invalid
parameter lpm_clock_gating=1
    [    1.197503] dwc2 30180000.usb: EPs: 10, dedicated fifos, 972
entries in SPRAM
    [    1.199459] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    1.489983] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB,
chardev (244:0)
    [    1.493533]  mmcblk0: p1 p2 p3
    [    1.524856] EXT4-fs (mmcblk0p1): mounted filesystem with
ordered data mode. Opts: (null)
    [    1.525716] VFS: Mounted root (ext4 filesystem) on device 179:1.
    [    1.527211] devtmpfs: mounted
    [    1.530123] Freeing unused kernel memory: 1024K
    [    1.537665] Run /sbin/init as init process
    [    1.597420] usb 1-1: new high-speed USB device number 2 using
ehci-platform
    [    1.649836] usb 1-1: New USB device found, idVendor=05e3,
idProduct=0610, bcdDevice=32.98
    [    1.650591] usb 1-1: New USB device strings: Mfr=0, Product=1,
SerialNumber=0
    [    1.651236] usb 1-1: Product: USB2.0 Hub
    [    1.653862] hub 1-1:1.0: USB hub found
    [    1.654696] hub 1-1:1.0: 4 ports detected
    [    1.977454] usb 1-1.1: new full-speed USB device number 3 using
ehci-platform
    [    2.130837] usb 1-1.1: New USB device found, idVendor=163c,
idProduct=0407, bcdDevice= 0.01
    [    2.131654] usb 1-1.1: New USB device strings: Mfr=1,
Product=2, SerialNumber=0
    [    2.132317] usb 1-1.1: Product: USB Key
    [    2.132673] usb 1-1.1: Manufacturer: Watchdata
    [    2.442526] EXT4-fs: Warning: mounting with data=journal
disables delayed allocation and O_DIRECT support!
    [    2.453496] EXT4-fs (mmcblk0p3): mounted filesystem with
journalled data mode. Opts: data=journal
    [    2.619187] udevd[96]: starting version 3.2.7
    [    2.635211] random: udevd: uninitialized urandom read (16 bytes read)
    [    2.637861] random: udevd: uninitialized urandom read (16 bytes read)
    [    2.638686] random: udevd: uninitialized urandom read (16 bytes read)
    [    2.656198] udevd[96]: specified group 'kvm' unknown
    [    2.693678] udevd[97]: starting eudev-3.2.7
    [    3.022805] rk808-rtc rk808-rtc: registered as rtc0
    [    3.227418] wdtoken: loading out-of-tree module taints kernel.
    [    3.248176] usbcore: registered new interface driver WatchToken(2.6)
    [    5.290161] emlog:emlog_init: version 0.70 running, major is
243, MINOR is 1, max size 900 K.
    [    5.392396] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
    [    6.792766] urandom_read: 1 callbacks suppressed
    [    6.792781] random: dd: uninitialized urandom read (512 bytes read)
    [    7.074770] random: dbus-uuidgen: uninitialized urandom read
(12 bytes read)
    [    7.075530] random: dbus-uuidgen: uninitialized urandom read (8
bytes read)
    [   35.146552] random: crng init done
    [   35.146887] random: 2 urandom warning(s) missed due to ratelimiting
    [   35.227827] zram: Added device: zram0
    [   35.257802] zram0: detected capacity change from 0 to 108220416
    [   35.289142] Adding 105680k swap on /dev/zram0.  Priority:100
extents:1 across:105680k SS
    [   44.339044] of_dma_request_slave_channel: dma-names property of
node '/serial@10230000' missing or empty
    [   44.339905] ttyS0 - failed to request DMA
    [   44.679614] rk_gmac-dwmac 30200000.eth eth0: PHY [stmmac-0:01]
driver [Micrel KSZ886X Switch]
    [   44.687858] rk_gmac-dwmac 30200000.eth eth0: No Safety Features
support found
    [   44.688546] rk_gmac-dwmac 30200000.eth eth0: PTP not supported by HW
    [   44.689140] rk_gmac-dwmac 30200000.eth eth0: configuring for
phy/rmii link mode
    [   46.807797] rk_gmac-dwmac 30200000.eth eth0: Link is Up -
100Mbps/Full - flow control rx/tx
    [   59.647746] g_serial gadget: Gadget Serial v2.4
    [   59.648178] g_serial gadget: g_serial ready
    [   59.653920] dwc2 30180000.usb: bound driver g_serial
    [   59.912364] dwc2 30180000.usb: new device is high-speed
    [   59.949981] dwc2 30180000.usb: new address 12
    [   60.034937] g_serial gadget: high-speed config #2: CDC ACM config
    [   65.980382] phy phy-10300000.syscon:usb2-phy@100.0: charger =
USB_CDP_CHARGER
    [   66.313267] dwc2 30180000.usb: new device is high-speed
    [   66.350902] dwc2 30180000.usb: new address 13
    [   66.388065] g_serial gadget: high-speed config #2: CDC ACM config
    [  311.604251] dwc2 30180000.usb: new device is high-speed
    [  311.641798] dwc2 30180000.usb: new address 14
    [  311.745597] g_serial gadget: high-speed config #2: CDC ACM config
    [  312.905102] dwc2 30180000.usb: new device is high-speed
    [  312.944301] dwc2 30180000.usb: new address 15
    [  312.967867] g_serial gadget: high-speed config #2: CDC ACM config
    [  314.828173] dwc2 30180000.usb: new device is high-speed
    [  314.866943] dwc2 30180000.usb: new address 16
    [  314.889550] g_serial gadget: high-speed config #2: CDC ACM config


The "[  314.889550] g_serial gadget: high-speed config #2: CDC ACM
config" message is the last time it is detected. As mentioned, to
restore the port to work, we need to reload the g_serial module.

When we reload it, following exception happens:

    [  923.942418] pc : [<c0850638>]    lr : [<bf045d44>]    psr: a00f0093
    [  923.942979] sp : c6739d48  ip : 00005401  fp : c5938038
    [  923.943445] r10: 00000000  r9 : ffffffed  r8 : c5c88480
    [  923.943914] r7 : c0aef318  r6 : 000000d4  r5 : 00000000  r4 : 00000000
    [  923.944498] r3 : 00000000  r2 : c5ecd400  r1 : c5c88480  r0 : 000000d4
    [  923.945092] Flags: NzCv  IRQs off  FIQs on  Mode SVC_32  ISA
ARM  Segment none
    [  923.945737] Control: 10c5387d  Table: 65cbc06a  DAC: 00000051
    [  923.946256] Process sat (pid: 604, stack limit = 0xa8f463ac)
    [  923.946768] Stack: (0xc6739d48 to 0xc673a000)
    [  923.947168] 9d40:                   c6738000 00000000 c5c88480
c5ecd400 c5c88480 c0d05c88
    [  923.947901] 9d60: 00000000 c5ecd400 00000000 0f200000 c0aef318
c5c88480 ffffffed c04f96e8
    [  923.948634] 9d80: c5ecd400 c05013bc c5ecd400 00000000 00000000
c5c88480 c5ecd400 0f200000
    [  923.949367] 9da0: c0aef318 c6738000 ffffffed c096dc70 c5938038
c04fb5a4 00000902 c0d8ec98
    [  923.950099] 9dc0: c5ecd400 c708b9d0 00000000 c0d05c88 00000000
c096dcf0 c593a140 00000000
    [  923.950832] 9de0: 00000000 c5938038 c5c88480 c5938038 c5c88480
c02b509c c6739ec8 c0d05c88
    [  923.951564] 9e00: c5938038 c5c88480 00000000 c5938038 00000000
c5c88488 c02b4fbc c02ac538
    [  923.952296] 9e20: c6739ec8 00000000 00000902 00000000 00000002
00000000 c5938038 c02bf778
    [  923.953028] 9e40: c6739e68 00000003 00000000 00000006 00000000
000041ed 00000000 00000000
    [  923.953760] 9e60: 00000041 00000047 00000000 00000000 00000000
ffffe000 00000000 c0a744d0
    [  923.954493] 9e80: 00000002 c5938038 c708b9d0 c6f313b8 c6d138c0
00004000 00000000 c0d05c88
    [  923.955225] 9ea0: c6738000 00000012 c6739f70 00000001 fffff000
c0101204 c6738000 00000142
    [  923.955958] 9ec0: b6346874 c02c1930 c708b9d0 c6f313b8 ad6e75ef
00000006 c70dc015 00000000
    [  923.956689] 9ee0: 00000000 c6cba6e8 c5938038 00000101 00000002
00000054 00000000 00000000
    [  923.957421] 9f00: 00000000 c6739f08 c59116f8 c65c3608 00000001
00000000 00000000 00000000
    [  923.958153] 9f20: 00000000 c0d05c88 c0d0626c 00000012 00000020
c593eb00 c70dc000 00000000
    [  923.958885] 9f40: 00000400 00000002 ffffff9c ffffff9c c70dc000
c0d05c88 00000012 ffffff9c
    [  923.959617] 9f60: c70dc000 c02adb5c 0000004e c0101204 00000902
00000000 00000006 00000100
    [  923.960349] 9f80: 00000001 c0d05c88 00000047 003e4ff0 00674450
0000000d 00000142 c0101204
    [  923.961082] 9fa0: c6738000 c0101000 003e4ff0 00674450 ffffff9c
003e4ff0 00000902 00000000
    [  923.961814] 9fc0: 003e4ff0 00674450 0000000d 00000142 b57ff011
00040000 00040000 b6346874
    [  923.962547] 9fe0: 00000002 b6346688 b65478d0 b6f4867c 600f0010
ffffff9c 00000000 00000000
    [  923.963304] [<c0850638>] (_raw_spin_lock_irq) from [<bf045d44>]
(gs_close+0x2c/0x1f0 [u_serial])
    [  923.964117] [<bf045d44>] (gs_close [u_serial]) from
[<c04f96e8>] (tty_release+0xf0/0x49c)
    [  923.964863] [<c04f96e8>] (tty_release) from [<c04fb5a4>]
(tty_open+0x118/0x450)
    [  923.965526] [<c04fb5a4>] (tty_open) from [<c02b509c>]
(chrdev_open+0xe0/0x1b4)
    [  923.966188] [<c02b509c>] (chrdev_open) from [<c02ac538>]
(do_dentry_open+0x114/0x3f4)
    [  923.966897] [<c02ac538>] (do_dentry_open) from [<c02bf778>]
(path_openat+0x2f8/0x1128)
    [  923.967613] [<c02bf778>] (path_openat) from [<c02c1930>]
(do_filp_open+0x74/0xe4)
    [  923.968290] [<c02c1930>] (do_filp_open) from [<c02adb5c>]
(do_sys_open+0x174/0x208)
    [  923.968985] [<c02adb5c>] (do_sys_open) from [<c0101000>]
(ret_fast_syscall+0x0/0x54)
    [  923.969675] Exception stack(0xc6739fa8 to 0xc6739ff0)
    [  923.970136] 9fa0:                   003e4ff0 00674450 ffffff9c
003e4ff0 00000902 00000000
    [  923.970868] 9fc0: 003e4ff0 00674450 0000000d 00000142 b57ff011
00040000 00040000 b6346874
    [  923.971597] 9fe0: 00000002 b6346688 b65478d0 b6f4867c
    [  923.972065] Code: f57ff05b e12fff1e f10c0080 f590f000 (e1903f9f)
    [  923.972618] ---[ end trace 02edbbb9948c159c ]---
    [  938.908716] g_serial gadget: Gadget Serial v2.4
    [  938.909152] g_serial gadget: g_serial ready
    [  938.917148] dwc2 30180000.usb: bound driver g_serial
    [  939.176179] dwc2 30180000.usb: new device is high-speed
    [  939.215459] dwc2 30180000.usb: new address 17
    [  939.422037] g_serial gadget: high-speed config #2: CDC ACM config

So, I am a bit lost how to debug this so I'd like to know what kind of
information might be useful to find the root cause of it?

-- 
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://code.ossystems.com.br
Mobile: +55 (53) 9 9981-7854          Mobile: +1 (347) 903-9750

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-14 13:40 USB DWC2 stops responding when insert/remove cable multiple times Otavio Salvador
@ 2020-02-17  8:58 ` Minas Harutyunyan
  2020-02-17 12:30   ` Otavio Salvador
  0 siblings, 1 reply; 11+ messages in thread
From: Minas Harutyunyan @ 2020-02-17  8:58 UTC (permalink / raw)
  To: Otavio Salvador, Greg Kroah-Hartman, linux-usb, Felipe Balbi,
	Heiko Stuebner, linux-rockchip, Johan Hovold

Hi Otavio,

On 2/14/2020 5:40 PM, Otavio Salvador wrote:
>   the USB port stops responding. To recover the port we need to reload
> the g_serial module.
> 
> I have reports of it happening in the field, on the device but, until
> recently, it very hard to reproduce. We found that it is very easy to
> reproduce when we use the Microsoft Surface Dock, as hub.
> 
> Description of the host:
> 
>      Operating System: Windows 10 Pro
>      Driver: libusb-1.0 1.0.22
> 
> Description of the target:
> 
>      SoC: Rockchip RV1108G
>      Gadget: g_serial
>      Linux: 5.4.19
> 
> dmesg:
>      [   59.647746] g_serial gadget: Gadget Serial v2.4
>      [   59.648178] g_serial gadget: g_serial ready
>      [   59.653920] dwc2 30180000.usb: bound driver g_serial
>      [   59.912364] dwc2 30180000.usb: new device is high-speed
>      [   59.949981] dwc2 30180000.usb: new address 12
>      [   60.034937] g_serial gadget: high-speed config #2: CDC ACM config
>      [   65.980382] phy phy-10300000.syscon:usb2-phy@100.0: charger =
> USB_CDP_CHARGER
>      [   66.313267] dwc2 30180000.usb: new device is high-speed
>      [   66.350902] dwc2 30180000.usb: new address 13
>      [   66.388065] g_serial gadget: high-speed config #2: CDC ACM config
>      [  311.604251] dwc2 30180000.usb: new device is high-speed
>      [  311.641798] dwc2 30180000.usb: new address 14
>      [  311.745597] g_serial gadget: high-speed config #2: CDC ACM config
>      [  312.905102] dwc2 30180000.usb: new device is high-speed
>      [  312.944301] dwc2 30180000.usb: new address 15
>      [  312.967867] g_serial gadget: high-speed config #2: CDC ACM config
>      [  314.828173] dwc2 30180000.usb: new device is high-speed
>      [  314.866943] dwc2 30180000.usb: new address 16
>      [  314.889550] g_serial gadget: high-speed config #2: CDC ACM config
> 

I assume here you few time disconnected and then connected cable and 
after last connection even when g_serial seen in last line it stop work. 
Correct?

> 
> The "[  314.889550] g_serial gadget: high-speed config #2: CDC ACM
> config" message is the last time it is detected. As mentioned, to
> restore the port to work, we need to reload the g_serial module.
> 
> When we reload it, following exception happens:
> 

Actually exception happen in g_serial not dwc2. Why you assume that it 
because of dwc2?

>      [  923.962547] 9fe0: 00000002 b6346688 b65478d0 b6f4867c 600f0010
> ffffff9c 00000000 00000000
>      [  923.963304] [<c0850638>] (_raw_spin_lock_irq) from [<bf045d44>]
> (gs_close+0x2c/0x1f0 [u_serial])
>      [  923.964117] [<bf045d44>] (gs_close [u_serial]) from
> [<c04f96e8>] (tty_release+0xf0/0x49c)
>      [  923.964863] [<c04f96e8>] (tty_release) from [<c04fb5a4>]
> (tty_open+0x118/0x450)
>      [  923.965526] [<c04fb5a4>] (tty_open) from [<c02b509c>]
> (chrdev_open+0xe0/0x1b4)
>      [  923.966188] [<c02b509c>] (chrdev_open) from [<c02ac538>]
> (do_dentry_open+0x114/0x3f4)
>      [  923.966897] [<c02ac538>] (do_dentry_open) from [<c02bf778>]
> (path_openat+0x2f8/0x1128)
>      [  923.967613] [<c02bf778>] (path_openat) from [<c02c1930>]
> (do_filp_open+0x74/0xe4)
>      [  923.968290] [<c02c1930>] (do_filp_open) from [<c02adb5c>]
> (do_sys_open+0x174/0x208)
>      [  923.968985] [<c02adb5c>] (do_sys_open) from [<c0101000>]
> (ret_fast_syscall+0x0/0x54)
>      [  923.969675] Exception stack(0xc6739fa8 to 0xc6739ff0)
>      [  923.970136] 9fa0:                   003e4ff0 00674450 ffffff9c
> 003e4ff0 00000902 00000000
>      [  923.970868] 9fc0: 003e4ff0 00674450 0000000d 00000142 b57ff011
> 00040000 00040000 b6346874
>      [  923.971597] 9fe0: 00000002 b6346688 b65478d0 b6f4867c
>      [  923.972065] Code: f57ff05b e12fff1e f10c0080 f590f000 (e1903f9f)
>      [  923.972618] ---[ end trace 02edbbb9948c159c ]---
>      [  938.908716] g_serial gadget: Gadget Serial v2.4
>      [  938.909152] g_serial gadget: g_serial ready
>      [  938.917148] dwc2 30180000.usb: bound driver g_serial
>      [  939.176179] dwc2 30180000.usb: new device is high-speed
>      [  939.215459] dwc2 30180000.usb: new address 17
>      [  939.422037] g_serial gadget: high-speed config #2: CDC ACM config
> 
> So, I am a bit lost how to debug this so I'd like to know what kind of
> information might be useful to find the root cause of it?

And despite of above exception, g_serial enumerated it works fine?


Please provide me dump of follow dwc2 debugfs's: regdump, hw_params, params.

Thanks,
Minas


^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-17  8:58 ` Minas Harutyunyan
@ 2020-02-17 12:30   ` Otavio Salvador
  2020-02-17 13:26     ` Minas Harutyunyan
  0 siblings, 1 reply; 11+ messages in thread
From: Otavio Salvador @ 2020-02-17 12:30 UTC (permalink / raw)
  To: Minas Harutyunyan
  Cc: Greg Kroah-Hartman, linux-usb, Felipe Balbi, Heiko Stuebner,
	linux-rockchip, Johan Hovold

Hello Minas,

On Mon, Feb 17, 2020 at 5:58 AM Minas Harutyunyan
<Minas.Harutyunyan@synopsys.com> wrote:
> On 2/14/2020 5:40 PM, Otavio Salvador wrote:
...
> >      [  312.967867] g_serial gadget: high-speed config #2: CDC ACM config
> >      [  314.828173] dwc2 30180000.usb: new device is high-speed
> >      [  314.866943] dwc2 30180000.usb: new address 16
> >      [  314.889550] g_serial gadget: high-speed config #2: CDC ACM config
> >
>
> I assume here you few time disconnected and then connected cable and
> after last connection even when g_serial seen in last line it stop work.
> Correct?

Yes. It stops responding.

> > The "[  314.889550] g_serial gadget: high-speed config #2: CDC ACM
> > config" message is the last time it is detected. As mentioned, to
> > restore the port to work, we need to reload the g_serial module.
> >
> > When we reload it, following exception happens:
> >
>
> Actually exception happen in g_serial not dwc2. Why you assume that it
> because of dwc2?

Indeed. After reporting this, it does sounds it is two decouple
issues. The tty seems to be not properly cleaned up and it seems to
have a resource not properly cleaned up.

...
> > So, I am a bit lost how to debug this so I'd like to know what kind of
> > information might be useful to find the root cause of it?
>
> And despite of above exception, g_serial enumerated it works fine?

If reloaded the USB is detected but tty seems to not work. It seems it
fails to free the ttyGS0 previously used and thus it cannot properly
create the new device.

> Please provide me dump of follow dwc2 debugfs's: regdump, hw_params, params.

Do you want this on working and failing state or just the failing one?

-- 
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://code.ossystems.com.br
Mobile: +55 (53) 9 9981-7854          Mobile: +1 (347) 903-9750

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-17 12:30   ` Otavio Salvador
@ 2020-02-17 13:26     ` Minas Harutyunyan
  2020-02-17 19:53       ` Otavio Salvador
  0 siblings, 1 reply; 11+ messages in thread
From: Minas Harutyunyan @ 2020-02-17 13:26 UTC (permalink / raw)
  To: Otavio Salvador, Minas Harutyunyan
  Cc: Greg Kroah-Hartman, linux-usb, Felipe Balbi, Heiko Stuebner,
	linux-rockchip, Johan Hovold

Hi Otavio,

On 2/17/2020 4:30 PM, Otavio Salvador wrote:
> Hello Minas,
> 
> On Mon, Feb 17, 2020 at 5:58 AM Minas Harutyunyan
> <Minas.Harutyunyan@synopsys.com> wrote:
>> On 2/14/2020 5:40 PM, Otavio Salvador wrote:
> ...
>>>       [  312.967867] g_serial gadget: high-speed config #2: CDC ACM config
>>>       [  314.828173] dwc2 30180000.usb: new device is high-speed
>>>       [  314.866943] dwc2 30180000.usb: new address 16
>>>       [  314.889550] g_serial gadget: high-speed config #2: CDC ACM config
>>>
>>
>> I assume here you few time disconnected and then connected cable and
>> after last connection even when g_serial seen in last line it stop work.
>> Correct?
> 
> Yes. It stops responding.
> 
>>> The "[  314.889550] g_serial gadget: high-speed config #2: CDC ACM
>>> config" message is the last time it is detected. As mentioned, to
>>> restore the port to work, we need to reload the g_serial module.
>>>
>>> When we reload it, following exception happens:
>>>
>>
>> Actually exception happen in g_serial not dwc2. Why you assume that it
>> because of dwc2?
> 
> Indeed. After reporting this, it does sounds it is two decouple
> issues. The tty seems to be not properly cleaned up and it seems to
> have a resource not properly cleaned up.
> 
Enable debug prints to get full dwc2 debug prints to see what happen 
with dwc2.

> ...
>>> So, I am a bit lost how to debug this so I'd like to know what kind of
>>> information might be useful to find the root cause of it?
>>
>> And despite of above exception, g_serial enumerated it works fine?
> 
> If reloaded the USB is detected but tty seems to not work. It seems it
> fails to free the ttyGS0 previously used and thus it cannot properly
> create the new device.
> 
>> Please provide me dump of follow dwc2 debugfs's: regdump, hw_params, params.
> 
> Do you want this on working and failing state or just the failing one?
> 
After failing.


Thanks,
Minas

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-17 13:26     ` Minas Harutyunyan
@ 2020-02-17 19:53       ` Otavio Salvador
  2020-02-19 12:26         ` Minas Harutyunyan
  0 siblings, 1 reply; 11+ messages in thread
From: Otavio Salvador @ 2020-02-17 19:53 UTC (permalink / raw)
  To: Minas Harutyunyan
  Cc: Greg Kroah-Hartman, linux-usb, Felipe Balbi, Heiko Stuebner,
	linux-rockchip, Johan Hovold

Hello Minas,

On Mon, Feb 17, 2020 at 10:26 AM Minas Harutyunyan
<Minas.Harutyunyan@synopsys.com> wrote:
> Enable debug prints to get full dwc2 debug prints to see what happen
> with dwc2.

[ 1053.870042] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1053.870051] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1053.870069] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1053.870086] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0305, I=0409, L=00ff
[ 1053.870109] dwc2 30180000.usb: ep0: req e7f6a9ab: 66@abed5c1d,
noi=0, zero=1, snok=0
[ 1053.870128] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1053.870141] dwc2 30180000.usb: ureq->length:66 ureq->actual:0
[ 1053.870157] dwc2 30180000.usb: dwc2_hsotg_start_req: 2@66/66,
0x00100042 => 0x00000910
[ 1053.870172] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1053.870182] dwc2 30180000.usb: ep0 state:1
[ 1053.870193] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1053.870205] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1053.870242] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1053.870255] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1053.870273] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1053.870287] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=00180066
[ 1053.870302] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 66
[ 1053.870316] dwc2 30180000.usb: req->length:66 req->actual:66 req->zero:1
[ 1053.870327] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1053.870377] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1053.870390] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1053.870405] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1053.870419] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=00000000
[ 1053.870430] dwc2 30180000.usb: zlp packet received
[ 1053.870445] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1053.870456] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1053.870472] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1053.870487] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1053.870499] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1053.870513] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1053.870526] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1053.870537] dwc2 30180000.usb: ep0 state:0
[ 1053.870548] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1053.870561] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1053.870585] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1053.870598] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1053.870612] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1053.870623] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1053.870641] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1053.870658] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0306, I=0409, L=00ff
[ 1053.870681] dwc2 30180000.usb: ep0: req e7f6a9ab: 26@abed5c1d,
noi=0, zero=1, snok=0
[ 1053.870698] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1053.870712] dwc2 30180000.usb: ureq->length:26 ureq->actual:0
[ 1053.870726] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@26/26,
0x0008001a => 0x00000910
[ 1053.870742] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1053.870752] dwc2 30180000.usb: ep0 state:1
[ 1053.870763] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1053.870776] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1053.870806] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1053.870819] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1053.870835] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1053.870849] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=0010004c
[ 1053.870866] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 26
[ 1053.870878] dwc2 30180000.usb: req->length:26 req->actual:26 req->zero:1
[ 1053.870889] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1053.870931] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1053.870945] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1053.870962] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1053.870976] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=60000078
[ 1053.870986] dwc2 30180000.usb: zlp packet received
[ 1053.871002] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1053.871014] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1053.871030] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1053.871046] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1053.871058] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1053.871072] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1053.871086] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1053.871097] dwc2 30180000.usb: ep0 state:0
[ 1053.871110] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1053.871122] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1053.872817] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1053.872834] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1053.872850] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1053.872862] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1053.872880] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1053.872897] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0300, I=0000, L=00ff
[ 1053.872920] dwc2 30180000.usb: ep0: req e7f6a9ab: 4@abed5c1d,
noi=0, zero=1, snok=0
[ 1053.872939] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1053.872950] dwc2 30180000.usb: ureq->length:4 ureq->actual:0
[ 1053.872966] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@4/4,
0x00080004 => 0x00000910
[ 1053.872980] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1053.872992] dwc2 30180000.usb: ep0 state:1
[ 1053.873005] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1053.873021] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1053.873060] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1053.873073] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1053.873091] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1053.873112] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=00080048
[ 1053.873129] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 4
[ 1053.873142] dwc2 30180000.usb: req->length:4 req->actual:4 req->zero:1
[ 1053.873155] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1053.873202] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1053.873216] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1053.873235] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1053.873248] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=20000070
[ 1053.873259] dwc2 30180000.usb: zlp packet received
[ 1053.873277] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1053.873290] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1053.873306] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1053.873324] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1053.873338] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1053.873352] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1053.873366] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1053.873380] dwc2 30180000.usb: ep0 state:0
[ 1053.873390] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1053.873404] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1053.873432] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1053.873446] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1053.873461] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1053.873474] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1053.873492] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1053.873512] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0303, I=0409, L=00ff
[ 1053.873532] dwc2 30180000.usb: driver->setup() ret -22
[ 1053.873542] dwc2 30180000.usb: ep0 stall (dir=1)
[ 1053.873558] dwc2 30180000.usb: written DXEPCTL=0x04228000 to
00000900 (DXEPCTL=0x00208000)
[ 1053.873567] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1053.873583] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1053.873600] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00228000, ep 0, dir out
[ 1053.873613] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1053.873627] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1053.873640] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1053.873650] dwc2 30180000.usb: ep0 state:0
[ 1053.873663] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80228000
[ 1053.873675] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80228000
[ 1053.873873] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1053.873894] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00040000
[ 1053.873912] dwc2 30180000.usb: dwc2_hsotg_epint: ep2(out) DxEPINT=0x00000001
[ 1053.873927] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00098200, DXEPTSIZ=140ede0a
[ 1053.873948] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
963b7097, 0 => 6513dd96
[ 1053.873978] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00098200, ep 2, dir out
[ 1053.873991] dwc2 30180000.usb: ureq->length:512 ureq->actual:0
[ 1053.874009] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@512/512,
0x00080200 => 0x00000b50
[ 1053.874028] dwc2 30180000.usb: dwc2_hsotg_start_req: 67102000 pad
=> 0x00000b54
[ 1053.874042] dwc2 30180000.usb: ep0 state:0
[ 1053.874054] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84098200
[ 1053.874066] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80098200
[ 1054.053865] dwc2 30180000.usb: ep2out: req 963b7097: 512@d2001eff,
noi=0, zero=0, snok=0
[ 1054.108727] dwc2 30180000.usb: ep1in: req 01eff31b: 353@bf8d62d8,
noi=0, zero=1, snok=0
[ 1054.108761] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x008a8200, ep 1, dir in
[ 1054.108778] dwc2 30180000.usb: ureq->length:353 ureq->actual:0
[ 1054.108799] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@353/353,
0x20080161 => 0x00000930
[ 1054.108819] dwc2 30180000.usb: dwc2_hsotg_start_req: 67101000 pad
=> 0x00000934
[ 1054.108833] dwc2 30180000.usb: ep0 state:0
[ 1054.108846] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x848a8200
[ 1054.108862] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80888200
[ 1054.108909] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.108930] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000002
[ 1054.108954] dwc2 30180000.usb: dwc2_hsotg_epint: ep1(in) DxEPINT=0x00000001
[ 1054.108972] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00898200, DXEPTSIZ=14d61208
[ 1054.108994] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 353
[ 1054.109008] dwc2 30180000.usb: req->length:353 req->actual:353 req->zero:1
[ 1054.109029] dwc2 30180000.usb: complete: ep 4ee0de58 ep1in, req
01eff31b, 0 => b0bb1e62
[ 1054.212217] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.212241] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00040000
[ 1054.212264] dwc2 30180000.usb: dwc2_hsotg_epint: ep2(out) DxEPINT=0x00000001
[ 1054.212285] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00088200, DXEPTSIZ=1406dd48
[ 1054.212317] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
1ed2ea34, 0 => 6513dd96
[ 1054.212380] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00088200, ep 2, dir out
[ 1054.212399] dwc2 30180000.usb: ureq->length:512 ureq->actual:0
[ 1054.212420] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@512/512,
0x00080200 => 0x00000b50
[ 1054.212437] dwc2 30180000.usb: dwc2_hsotg_start_req: 67102000 pad
=> 0x00000b54
[ 1054.212452] dwc2 30180000.usb: ep0 state:0
[ 1054.212463] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84088200
[ 1054.212479] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80088200
[ 1054.212571] dwc2 30180000.usb: ep2out: req 1ed2ea34: 512@12ae06de,
noi=0, zero=0, snok=0
[ 1054.267399] dwc2 30180000.usb: ep1in: req 01eff31b: 353@bf8d62d8,
noi=0, zero=1, snok=0
[ 1054.267438] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00898200, ep 1, dir in
[ 1054.267457] dwc2 30180000.usb: ureq->length:353 ureq->actual:0
[ 1054.267480] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@353/353,
0x20080161 => 0x00000930
[ 1054.267498] dwc2 30180000.usb: dwc2_hsotg_start_req: 67101000 pad
=> 0x00000934
[ 1054.267514] dwc2 30180000.usb: ep0 state:0
[ 1054.267527] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84898200
[ 1054.267541] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80898200
[ 1054.267590] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.267608] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000002
[ 1054.267633] dwc2 30180000.usb: dwc2_hsotg_epint: ep1(in) DxEPINT=0x00000001
[ 1054.267653] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00888200, DXEPTSIZ=14ce10a7
[ 1054.267674] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 353
[ 1054.267690] dwc2 30180000.usb: req->length:353 req->actual:353 req->zero:1
[ 1054.267712] dwc2 30180000.usb: complete: ep 4ee0de58 ep1in, req
01eff31b, 0 => b0bb1e62
[ 1054.370753] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.370777] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00040000
[ 1054.370800] dwc2 30180000.usb: dwc2_hsotg_epint: ep2(out) DxEPINT=0x00000001
[ 1054.370818] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00098200, DXEPTSIZ=13fedc86
[ 1054.370848] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
21db14dd, 0 => 6513dd96
[ 1054.370907] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00098200, ep 2, dir out
[ 1054.370924] dwc2 30180000.usb: ureq->length:512 ureq->actual:0
[ 1054.370943] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@512/512,
0x00080200 => 0x00000b50
[ 1054.370961] dwc2 30180000.usb: dwc2_hsotg_start_req: 67102000 pad
=> 0x00000b54
[ 1054.370976] dwc2 30180000.usb: ep0 state:0
[ 1054.370987] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84098200
[ 1054.371003] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80098200
[ 1054.371122] dwc2 30180000.usb: ep2out: req 21db14dd: 512@229f7a33,
noi=0, zero=0, snok=0
[ 1054.426075] dwc2 30180000.usb: ep1in: req 01eff31b: 353@bf8d62d8,
noi=0, zero=1, snok=0
[ 1054.426112] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00888200, ep 1, dir in
[ 1054.426129] dwc2 30180000.usb: ureq->length:353 ureq->actual:0
[ 1054.426149] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@353/353,
0x20080161 => 0x00000930
[ 1054.426168] dwc2 30180000.usb: dwc2_hsotg_start_req: 67101000 pad
=> 0x00000934
[ 1054.426184] dwc2 30180000.usb: ep0 state:0
[ 1054.426197] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84888200
[ 1054.426211] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80888200
[ 1054.426257] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.426278] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000002
[ 1054.426298] dwc2 30180000.usb: dwc2_hsotg_epint: ep1(in) DxEPINT=0x00000001
[ 1054.426315] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00898200, DXEPTSIZ=14c60f46
[ 1054.426335] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 353
[ 1054.426352] dwc2 30180000.usb: req->length:353 req->actual:353 req->zero:1
[ 1054.426375] dwc2 30180000.usb: complete: ep 4ee0de58 ep1in, req
01eff31b, 0 => b0bb1e62
[ 1054.529548] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.529579] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00040000
[ 1054.529602] dwc2 30180000.usb: dwc2_hsotg_epint: ep2(out) DxEPINT=0x00000001
[ 1054.529621] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00088200, DXEPTSIZ=13f6dbc4
[ 1054.529652] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
26bd9b9f, 0 => 6513dd96
[ 1054.529704] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00088200, ep 2, dir out
[ 1054.529721] dwc2 30180000.usb: ureq->length:512 ureq->actual:0
[ 1054.529741] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@512/512,
0x00080200 => 0x00000b50
[ 1054.529758] dwc2 30180000.usb: dwc2_hsotg_start_req: 67102000 pad
=> 0x00000b54
[ 1054.529774] dwc2 30180000.usb: ep0 state:0
[ 1054.529785] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84088200
[ 1054.529801] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80088200
[ 1054.529928] dwc2 30180000.usb: ep2out: req 26bd9b9f: 512@06b7dbca,
noi=0, zero=0, snok=0
[ 1054.537095] dwc2 30180000.usb: dwc2_hsotg_irq: 04008428 00000400
(d88c3cc4) retry 8
[ 1054.537119] dwc2 30180000.usb: GINTSTS_ErlySusp
[ 1054.540147] dwc2 30180000.usb: gintsts=04008828  gintmsk=d88c3cc4
[ 1054.540172] dwc2 30180000.usb: USB SUSPEND
[ 1054.540191] dwc2 30180000.usb: dwc2_handle_usb_suspend_intr: DSTS=0x5ad801
[ 1054.540211] dwc2 30180000.usb: DSTS.Suspend Status=1 HWCFG4.Power
Optimize=1 HWCFG4.Hibernation=0
[ 1054.540242] dwc2 30180000.usb: dwc2_hsotg_irq: 04008028 00000000
(d88c3cc4) retry 8
[ 1054.585402] dwc2 30180000.usb: ep1in: req 01eff31b: 353@bf8d62d8,
noi=0, zero=1, snok=0
[ 1054.585422] dwc2 30180000.usb: dwc2_hsotg_ep_queue: submit request
only in active state
[ 1054.661667] dwc2 30180000.usb: dwc2_hsotg_irq: 04008428 00000400
(d88c3cc4) retry 8
[ 1054.661694] dwc2 30180000.usb: GINTSTS_ErlySusp
[ 1054.664715] dwc2 30180000.usb: gintsts=04008828  gintmsk=d88c3cc4
[ 1054.664741] dwc2 30180000.usb: USB SUSPEND
[ 1054.664760] dwc2 30180000.usb: dwc2_handle_usb_suspend_intr: DSTS=0x5ad801
[ 1054.664781] dwc2 30180000.usb: DSTS.Suspend Status=1 HWCFG4.Power
Optimize=1 HWCFG4.Hibernation=0
[ 1054.664807] dwc2 30180000.usb: dwc2_hsotg_irq: 04008028 00000000
(d88c3cc4) retry 8
[ 1054.799737] dwc2 30180000.usb: dwc2_hsotg_irq: 04809028 00801000
(d88c3cc4) retry 8
[ 1054.799758] dwc2 30180000.usb: dwc2_hsotg_irq: USBRstDet
[ 1054.799776] dwc2 30180000.usb: dwc2_hsotg_irq: USBRst
[ 1054.799788] dwc2 30180000.usb: GNPTXSTS=00080010
[ 1054.799816] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, -108 => 84063983
[ 1054.799838] dwc2 30180000.usb: dwc2_hsotg_complete_setup: failed -108
[ 1054.799866] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
f278d077, -108 => 6513dd96
[ 1054.799914] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
841f6058, -108 => 6513dd96
[ 1054.799935] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
5215e7bb, -108 => 6513dd96
[ 1054.799954] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
9daf426b, -108 => 6513dd96
[ 1054.799976] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
9aafdbc0, -108 => 6513dd96
[ 1054.799995] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
03c36521, -108 => 6513dd96
[ 1054.800015] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
21266e76, -108 => 6513dd96
[ 1054.800033] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
00a94f37, -108 => 6513dd96
[ 1054.800052] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
fb52ff47, -108 => 6513dd96
[ 1054.800072] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
c53f7751, -108 => 6513dd96
[ 1054.800092] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
bcead652, -108 => 6513dd96
[ 1054.800110] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
53122b2a, -108 => 6513dd96
[ 1054.800129] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
963b7097, -108 => 6513dd96
[ 1054.800148] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
1ed2ea34, -108 => 6513dd96
[ 1054.800166] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
21db14dd, -108 => 6513dd96
[ 1054.800185] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
26bd9b9f, -108 => 6513dd96
[ 1054.800232] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep c5cae4f8)
[ 1054.800250] dwc2 30180000.usb: dwc2_hsotg_ep_stop_xfr: stopping
transfer on ep2out
[ 1054.800271] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08080200
[ 1054.800292] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 4ee0de58)
[ 1054.800304] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08890200
[ 1054.800402] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 022471aa)
[ 1054.800417] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x098c000a
[ 1054.800446] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 4ee0de58)
[ 1054.800458] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x088b0200
[ 1054.800472] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep c5cae4f8)
[ 1054.800483] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x080a0200
[ 1054.800496] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 022471aa)
[ 1054.800507] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x098e000a
[ 1054.800521] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 4d7d1abb)
[ 1054.800533] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08020400
[ 1054.800546] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 961b389a)
[ 1054.800558] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08020400
[ 1054.800573] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep cd493b4d)
[ 1054.800584] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08020400
[ 1054.800599] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 8ba68a83)
[ 1054.800613] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08020400
[ 1054.800628] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep ff21bf72)
[ 1054.800640] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08020400
[ 1054.800653] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 717d8735)
[ 1054.800665] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08020400
[ 1054.800680] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 15b03b70)
[ 1054.800692] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08020400
[ 1054.800707] dwc2 30180000.usb: dwc2_hsotg_ep_disable(ep 23ec528d)
[ 1054.800718] dwc2 30180000.usb: dwc2_hsotg_ep_disable: DxEPCTL=0x08020400
[ 1054.800735] dwc2 30180000.usb: HS UTMI+ PHY selected
[ 1054.800764] dwc2 30180000.usb: FIFOs reset, timeout at 100
[ 1054.800792] dwc2 30180000.usb: EP0: DIEPCTL0=0x00208000, DOEPCTL0=0x80228000
[ 1054.800808] dwc2 30180000.usb: gsintmsk now 0xd88c3cc4
[ 1054.800825] dwc2 30180000.usb: DCTL=0x00000000
[ 1054.803847] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.803872] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.803897] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x80208000, ep 0, dir out
[ 1054.803913] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.803933] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.803949] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.803961] dwc2 30180000.usb: ep0 state:0
[ 1054.803973] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80208000
[ 1054.803988] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80208000
[ 1054.804003] dwc2 30180000.usb: EP0: DIEPCTL0=0x00208000, DOEPCTL0=0x80208000
[ 1054.854485] dwc2 30180000.usb: dwc2_hsotg_irq: 04002020 00002000
(d88c3cc4) retry 8
[ 1054.854513] dwc2 30180000.usb: EnumDone (DSTS=0x001ad800)
[ 1054.854533] dwc2 30180000.usb: new device is high-speed
[ 1054.855048] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.855060] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup already queued???
[ 1054.855074] dwc2 30180000.usb: EP0: DIEPCTL0=0x00208000, DOEPCTL0=0x80208000
[ 1054.922959] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.922982] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.923005] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.923020] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.923048] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.923076] dwc2 30180000.usb: ctrl Type=00, Req=05, V=0036, I=0000, L=0000
[ 1054.923094] dwc2 30180000.usb: new address 54
[ 1054.923511] dwc2 30180000.usb: dwc2_hsotg_send_reply: buff 80653c92, len 0
[ 1054.923536] dwc2 30180000.usb: ep0: req 788a45df: 0@2fe5a4b6,
noi=0, zero=0, snok=0
[ 1054.923560] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.923576] dwc2 30180000.usb: ureq->length:0 ureq->actual:0
[ 1054.923597] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@0/0,
0x00080000 => 0x00000910
[ 1054.923614] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.923628] dwc2 30180000.usb: ep0 state:3
[ 1054.923640] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.923657] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.923758] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.923780] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.923798] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.923818] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=00000048
[ 1054.923837] dwc2 30180000.usb: zlp packet sent
[ 1054.923856] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
788a45df, 0 => 47923a45
[ 1054.923874] dwc2 30180000.usb: dwc2_hsotg_complete_oursetup: ep
c20b8608, req 788a45df
[ 1054.923892] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.923912] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.923937] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.923952] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.923968] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.923983] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.923995] dwc2 30180000.usb: ep0 state:0
[ 1054.924006] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.924019] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.939622] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.939640] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.939664] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.939680] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.939705] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.939732] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0100, I=0000, L=0008
[ 1054.939765] dwc2 30180000.usb: ep0: req e7f6a9ab: 8@abed5c1d,
noi=0, zero=0, snok=0
[ 1054.939787] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.939803] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.939822] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000910
[ 1054.939838] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.939850] dwc2 30180000.usb: ep0 state:1
[ 1054.939861] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.939874] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.939926] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.939943] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.939960] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.939976] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=00180040
[ 1054.939998] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 8
[ 1054.940012] dwc2 30180000.usb: req->length:8 req->actual:8 req->zero:0
[ 1054.940027] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.940076] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.940091] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.940106] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.940123] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=40000078
[ 1054.940138] dwc2 30180000.usb: zlp packet received
[ 1054.940158] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.940173] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.940192] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.940213] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.940224] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.940238] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.940251] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.940264] dwc2 30180000.usb: ep0 state:0
[ 1054.940276] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.940288] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.940319] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.940334] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.940349] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.940360] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.940378] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.940396] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0100, I=0000, L=0012
[ 1054.940420] dwc2 30180000.usb: ep0: req e7f6a9ab: 18@abed5c1d,
noi=0, zero=0, snok=0
[ 1054.940436] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.940451] dwc2 30180000.usb: ureq->length:18 ureq->actual:0
[ 1054.940468] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@18/18,
0x00080012 => 0x00000910
[ 1054.940486] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.940496] dwc2 30180000.usb: ep0 state:1
[ 1054.940507] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.940522] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.940556] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.940569] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.940586] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.940600] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=0010002e
[ 1054.940617] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 18
[ 1054.940629] dwc2 30180000.usb: req->length:18 req->actual:18 req->zero:0
[ 1054.940642] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.940688] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.940703] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.940717] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.940731] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=20000070
[ 1054.940743] dwc2 30180000.usb: zlp packet received
[ 1054.940762] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.940774] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.940790] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.940808] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.940821] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.940836] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.940849] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.940859] dwc2 30180000.usb: ep0 state:0
[ 1054.940870] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.940884] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.940915] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.940927] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.940942] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.940952] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.940972] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.940988] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0200, I=0000, L=0009
[ 1054.941016] dwc2 30180000.usb: ep0: req e7f6a9ab: 9@abed5c1d,
noi=0, zero=0, snok=0
[ 1054.941035] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.941048] dwc2 30180000.usb: ureq->length:9 ureq->actual:0
[ 1054.941062] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@9/9,
0x00080009 => 0x00000910
[ 1054.941075] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.941085] dwc2 30180000.usb: ep0 state:1
[ 1054.941098] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.941111] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.941146] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.941160] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.941176] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.941192] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=00080025
[ 1054.941208] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 9
[ 1054.941222] dwc2 30180000.usb: req->length:9 req->actual:9 req->zero:0
[ 1054.941234] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.941262] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.941276] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.941291] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.941305] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=00000068
[ 1054.941315] dwc2 30180000.usb: zlp packet received
[ 1054.941333] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.941347] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.941363] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.941378] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.941391] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.941405] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.941418] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.941428] dwc2 30180000.usb: ep0 state:0
[ 1054.941441] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.941455] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.941484] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.941499] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.941514] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.941526] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.941544] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.941562] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0200, I=0000, L=004b
[ 1054.941585] dwc2 30180000.usb: ep0: req e7f6a9ab: 75@abed5c1d,
noi=0, zero=0, snok=0
[ 1054.941605] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.941618] dwc2 30180000.usb: ureq->length:75 ureq->actual:0
[ 1054.941634] dwc2 30180000.usb: dwc2_hsotg_start_req: 2@75/75,
0x0010004b => 0x00000910
[ 1054.941650] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.941664] dwc2 30180000.usb: ep0 state:1
[ 1054.941674] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.941688] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.941724] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.941737] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.941755] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.941768] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=0018005a
[ 1054.941786] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 75
[ 1054.941802] dwc2 30180000.usb: req->length:75 req->actual:75 req->zero:0
[ 1054.941813] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.941849] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.941862] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.941877] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.941891] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=60000060
[ 1054.941902] dwc2 30180000.usb: zlp packet received
[ 1054.941918] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.941932] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.941949] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.941967] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.941979] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.941993] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.942007] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.942019] dwc2 30180000.usb: ep0 state:0
[ 1054.942031] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.942045] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.942073] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.942085] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.942100] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.942111] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.942129] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.942146] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0300, I=0000, L=00ff
[ 1054.942170] dwc2 30180000.usb: ep0: req e7f6a9ab: 4@abed5c1d,
noi=0, zero=1, snok=0
[ 1054.942189] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.942201] dwc2 30180000.usb: ureq->length:4 ureq->actual:0
[ 1054.942215] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@4/4,
0x00080004 => 0x00000910
[ 1054.942229] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.942239] dwc2 30180000.usb: ep0 state:1
[ 1054.942251] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.942263] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.942296] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.942311] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.942327] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.942341] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=00100056
[ 1054.942357] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 4
[ 1054.942369] dwc2 30180000.usb: req->length:4 req->actual:4 req->zero:1
[ 1054.942380] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.942416] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.942431] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.942446] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.942460] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=40000058
[ 1054.942470] dwc2 30180000.usb: zlp packet received
[ 1054.942487] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.942501] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.942516] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.942532] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.942547] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.942563] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.942575] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.942586] dwc2 30180000.usb: ep0 state:0
[ 1054.942597] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.942609] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.942642] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.942656] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.942672] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.942683] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.942703] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.942720] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0302, I=0409, L=00ff
[ 1054.942748] dwc2 30180000.usb: ep0: req e7f6a9ab: 20@abed5c1d,
noi=0, zero=1, snok=0
[ 1054.942766] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.942778] dwc2 30180000.usb: ureq->length:20 ureq->actual:0
[ 1054.942792] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@20/20,
0x00080014 => 0x00000910
[ 1054.942807] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.942817] dwc2 30180000.usb: ep0 state:1
[ 1054.942829] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.942845] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.942877] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.942891] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.942908] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.942922] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=00080042
[ 1054.942937] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 20
[ 1054.942950] dwc2 30180000.usb: req->length:20 req->actual:20 req->zero:1
[ 1054.942962] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.943001] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.943015] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.943030] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.943044] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=20000050
[ 1054.943055] dwc2 30180000.usb: zlp packet received
[ 1054.943070] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.943082] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.943099] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.943117] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.943129] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.943143] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.943158] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.943170] dwc2 30180000.usb: ep0 state:0
[ 1054.943182] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.943196] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.943225] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.943238] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.943253] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.943263] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.943281] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.943301] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0301, I=0409, L=00ff
[ 1054.943323] dwc2 30180000.usb: ep0: req e7f6a9ab: 20@abed5c1d,
noi=0, zero=1, snok=0
[ 1054.943342] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.943354] dwc2 30180000.usb: ureq->length:20 ureq->actual:0
[ 1054.943370] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@20/20,
0x00080014 => 0x00000910
[ 1054.943382] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.943393] dwc2 30180000.usb: ep0 state:1
[ 1054.943405] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.943419] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.943451] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.943467] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.943483] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.943498] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=0000002e
[ 1054.943518] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 20
[ 1054.943532] dwc2 30180000.usb: req->length:20 req->actual:20 req->zero:1
[ 1054.943545] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.943627] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.943644] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.943660] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.943676] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=00000048
[ 1054.943688] dwc2 30180000.usb: zlp packet received
[ 1054.943707] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.943722] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.943741] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.943760] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.943772] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.943788] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.943804] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.943816] dwc2 30180000.usb: ep0 state:0
[ 1054.943829] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.943843] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.943876] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.943890] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.943905] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.943916] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.943934] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.943955] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0303, I=0409, L=00ff
[ 1054.943974] dwc2 30180000.usb: driver->setup() ret -22
[ 1054.943988] dwc2 30180000.usb: ep0 stall (dir=1)
[ 1054.944006] dwc2 30180000.usb: written DXEPCTL=0x04228000 to
00000900 (DXEPCTL=0x00208000)
[ 1054.944017] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.944032] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.944051] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00228000, ep 0, dir out
[ 1054.944063] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.944077] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.944090] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.944101] dwc2 30180000.usb: ep0 state:0
[ 1054.944112] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80228000
[ 1054.944125] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.944157] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.944172] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.944186] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.944197] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.944214] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.944231] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0303, I=0409, L=00ff
[ 1054.944244] dwc2 30180000.usb: driver->setup() ret -22
[ 1054.944255] dwc2 30180000.usb: ep0 stall (dir=1)
[ 1054.944271] dwc2 30180000.usb: written DXEPCTL=0x04228000 to
00000900 (DXEPCTL=0x00208000)
[ 1054.944281] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.944297] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.944315] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00228000, ep 0, dir out
[ 1054.944327] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.944341] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.944354] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.944364] dwc2 30180000.usb: ep0 state:0
[ 1054.944377] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.944391] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.944424] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.944438] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.944453] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.944465] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.944485] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.944502] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0303, I=0409, L=00ff
[ 1054.944518] dwc2 30180000.usb: driver->setup() ret -22
[ 1054.944530] dwc2 30180000.usb: ep0 stall (dir=1)
[ 1054.944544] dwc2 30180000.usb: written DXEPCTL=0x04228000 to
00000900 (DXEPCTL=0x00208000)
[ 1054.944555] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.944571] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.944585] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00228000, ep 0, dir out
[ 1054.944597] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.944611] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.944627] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.944637] dwc2 30180000.usb: ep0 state:0
[ 1054.944648] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80228000
[ 1054.944661] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80228000
[ 1054.944690] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.944706] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.944722] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.944733] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.944752] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.944770] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0303, I=0409, L=0002
[ 1054.944786] dwc2 30180000.usb: driver->setup() ret -22
[ 1054.944796] dwc2 30180000.usb: ep0 stall (dir=1)
[ 1054.944810] dwc2 30180000.usb: written DXEPCTL=0x04228000 to
00000900 (DXEPCTL=0x00208000)
[ 1054.944821] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.944837] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.944855] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00228000, ep 0, dir out
[ 1054.944868] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.944882] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.944895] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.944905] dwc2 30180000.usb: ep0 state:0
[ 1054.944916] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80228000
[ 1054.944929] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.944959] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.944972] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.944986] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.944997] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.945014] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.945030] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0303, I=0409, L=0002
[ 1054.945045] dwc2 30180000.usb: driver->setup() ret -22
[ 1054.945055] dwc2 30180000.usb: ep0 stall (dir=1)
[ 1054.945069] dwc2 30180000.usb: written DXEPCTL=0x04228000 to
00000900 (DXEPCTL=0x00208000)
[ 1054.945080] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.945096] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.945112] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00228000, ep 0, dir out
[ 1054.945123] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.945137] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.945150] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.945161] dwc2 30180000.usb: ep0 state:0
[ 1054.945172] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80228000
[ 1054.945184] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.945214] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.945227] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.945243] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.945255] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.945275] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.945291] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0303, I=0409, L=0002
[ 1054.945305] dwc2 30180000.usb: driver->setup() ret -22
[ 1054.945316] dwc2 30180000.usb: ep0 stall (dir=1)
[ 1054.945330] dwc2 30180000.usb: written DXEPCTL=0x04228000 to
00000900 (DXEPCTL=0x00208000)
[ 1054.945340] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.945356] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.945374] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00228000, ep 0, dir out
[ 1054.945388] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.945402] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.945415] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.945427] dwc2 30180000.usb: ep0 state:0
[ 1054.945438] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80228000
[ 1054.945451] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80228000
[ 1054.946562] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.946576] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.946592] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.946604] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.946621] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.946638] dwc2 30180000.usb: ctrl Type=00, Req=09, V=0002, I=0000, L=0000
[ 1054.946658] g_serial gadget: high-speed config #2: CDC ACM config
[ 1054.947231] dwc2 30180000.usb: dwc2_hsotg_ep_enable: ep ep3in: a
0x83, attr 0x03, mps 0x000a, intr 9
[ 1054.947251] dwc2 30180000.usb: dwc2_hsotg_ep_enable: read
DxEPCTL=0x018e0400 from 0x00000960
[ 1054.947276] dwc2 30180000.usb: dwc2_hsotg_ep_enable: write DxEPCTL=0x118e800a
[ 1054.947290] dwc2 30180000.usb: dwc2_hsotg_ep_enable: read DxEPCTL=0x018e800a
[ 1054.947313] dwc2 30180000.usb: dwc2_hsotg_ep_enable: ep ep1in: a
0x81, attr 0x02, mps 0x0200, intr 0
[ 1054.947329] dwc2 30180000.usb: dwc2_hsotg_ep_enable: read
DxEPCTL=0x008b0400 from 0x00000920
[ 1054.947347] dwc2 30180000.usb: dwc2_hsotg_ep_enable: write DxEPCTL=0x108b8200
[ 1054.947360] dwc2 30180000.usb: dwc2_hsotg_ep_enable: read DxEPCTL=0x008a8200
[ 1054.947377] dwc2 30180000.usb: dwc2_hsotg_ep_enable: ep ep2out: a
0x02, attr 0x02, mps 0x0200, intr 0
[ 1054.947390] dwc2 30180000.usb: dwc2_hsotg_ep_enable: read
DxEPCTL=0x000a0400 from 0x00000b40
[ 1054.947402] dwc2 30180000.usb: dwc2_hsotg_ep_enable: write DxEPCTL=0x100a8200
[ 1054.947414] dwc2 30180000.usb: dwc2_hsotg_ep_enable: read DxEPCTL=0x000a8200
[ 1054.947485] dwc2 30180000.usb: ep2out: req 788a45df: 512@0542b9d7,
noi=0, zero=0, snok=0
[ 1054.947508] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x000a8200, ep 2, dir out
[ 1054.947521] dwc2 30180000.usb: ureq->length:512 ureq->actual:0
[ 1054.947537] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@512/512,
0x00080200 => 0x00000b50
[ 1054.947553] dwc2 30180000.usb: dwc2_hsotg_start_req: 67102000 pad
=> 0x00000b54
[ 1054.947566] dwc2 30180000.usb: ep0 state:3
[ 1054.947577] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x840a8200
[ 1054.947590] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80088200
[ 1054.947609] dwc2 30180000.usb: ep2out: req a40532cf: 512@51b87fad,
noi=0, zero=0, snok=0
[ 1054.947631] dwc2 30180000.usb: ep2out: req b11aed86: 512@6ac5f592,
noi=0, zero=0, snok=0
[ 1054.947649] dwc2 30180000.usb: ep2out: req 1190cac0: 512@fce7854c,
noi=0, zero=0, snok=0
[ 1054.947666] dwc2 30180000.usb: ep2out: req b620c645: 512@d63e4d5b,
noi=0, zero=0, snok=0
[ 1054.947683] dwc2 30180000.usb: ep2out: req 61d44c54: 512@1fc1d262,
noi=0, zero=0, snok=0
[ 1054.947701] dwc2 30180000.usb: ep2out: req ce9944e1: 512@0f49be3a,
noi=0, zero=0, snok=0
[ 1054.947720] dwc2 30180000.usb: ep2out: req a8c33c25: 512@1c5e703c,
noi=0, zero=0, snok=0
[ 1054.947737] dwc2 30180000.usb: ep2out: req 27e820b2: 512@2d4f8b5d,
noi=0, zero=0, snok=0
[ 1054.947755] dwc2 30180000.usb: ep2out: req 24da46aa: 512@ddb75599,
noi=0, zero=0, snok=0
[ 1054.947772] dwc2 30180000.usb: ep2out: req 837d9562: 512@4ccef93d,
noi=0, zero=0, snok=0
[ 1054.947790] dwc2 30180000.usb: ep2out: req ad58562c: 512@b1448277,
noi=0, zero=0, snok=0
[ 1054.947807] dwc2 30180000.usb: ep2out: req 19349ad6: 512@cdcf0375,
noi=0, zero=0, snok=0
[ 1054.947824] dwc2 30180000.usb: ep2out: req 22d0fa51: 512@ffc24d73,
noi=0, zero=0, snok=0
[ 1054.947842] dwc2 30180000.usb: ep2out: req 3fd4a46f: 512@bf469af9,
noi=0, zero=0, snok=0
[ 1054.947859] dwc2 30180000.usb: ep2out: req b2cd63ff: 512@e2d90c44,
noi=0, zero=0, snok=0
[ 1054.947886] dwc2 30180000.usb: ep3in: req a135c511: 10@e89c4f72,
noi=0, zero=0, snok=0
[ 1054.947902] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x018e800a, ep 3, dir in
[ 1054.947914] dwc2 30180000.usb: ureq->length:10 ureq->actual:0
[ 1054.947929] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@10/10,
0x2008000a => 0x00000970
[ 1054.947944] dwc2 30180000.usb: dwc2_hsotg_start_req: 67100000 pad
=> 0x00000974
[ 1054.947955] dwc2 30180000.usb: ep0 state:3
[ 1054.947966] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x858e800a
[ 1054.947980] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x818c800a
[ 1054.948004] dwc2 30180000.usb: ep0: req e7f6a9ab: 0@abed5c1d,
noi=0, zero=0, snok=0
[ 1054.948021] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.948034] dwc2 30180000.usb: ureq->length:0 ureq->actual:0
[ 1054.948048] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@0/0,
0x00080000 => 0x00000910
[ 1054.948060] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.948071] dwc2 30180000.usb: ep0 state:3
[ 1054.948082] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.948094] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.948134] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.948150] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000009
[ 1054.948168] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.948182] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=0018002e
[ 1054.948196] dwc2 30180000.usb: zlp packet sent
[ 1054.948215] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.948230] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.948246] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.948265] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.948277] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.948291] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.948305] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.948316] dwc2 30180000.usb: ep0 state:0
[ 1054.948327] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.948340] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.948361] dwc2 30180000.usb: dwc2_hsotg_epint: ep3(in) DxEPINT=0x00000001
[ 1054.948377] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x018c800a, DXEPTSIZ=0007fce0
[ 1054.948394] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 10
[ 1054.948409] dwc2 30180000.usb: req->length:10 req->actual:10 req->zero:0
[ 1054.948428] dwc2 30180000.usb: complete: ep 022471aa ep3in, req
a135c511, 0 => 493062e0
[ 1054.948470] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.948485] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.948503] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.948515] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.948535] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.948557] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0304, I=0409, L=00ff
[ 1054.948584] dwc2 30180000.usb: ep0: req e7f6a9ab: 30@abed5c1d,
noi=0, zero=1, snok=0
[ 1054.948601] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.948613] dwc2 30180000.usb: ureq->length:30 ureq->actual:0
[ 1054.948629] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@30/30,
0x0008001e => 0x00000910
[ 1054.948643] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.948655] dwc2 30180000.usb: ep0 state:1
[ 1054.948666] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.948680] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.948715] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.948727] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.948746] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.948760] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=00100010
[ 1054.948775] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 30
[ 1054.948788] dwc2 30180000.usb: req->length:30 req->actual:30 req->zero:1
[ 1054.948801] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.948839] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.948854] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.948869] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.948882] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=00000008
[ 1054.948894] dwc2 30180000.usb: zlp packet received
[ 1054.948913] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.948925] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.948941] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.948957] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.948969] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.948983] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.948998] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.949010] dwc2 30180000.usb: ep0 state:0
[ 1054.949023] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.949037] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.949068] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.949081] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.949096] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.949107] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.949125] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.949142] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0305, I=0409, L=00ff
[ 1054.949165] dwc2 30180000.usb: ep0: req e7f6a9ab: 66@abed5c1d,
noi=0, zero=1, snok=0
[ 1054.949181] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.949191] dwc2 30180000.usb: ureq->length:66 ureq->actual:0
[ 1054.949206] dwc2 30180000.usb: dwc2_hsotg_start_req: 2@66/66,
0x00100042 => 0x00000910
[ 1054.949220] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.949231] dwc2 30180000.usb: ep0 state:1
[ 1054.949242] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.949255] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.949289] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.949303] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.949319] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.949333] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=0000004e
[ 1054.949348] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 66
[ 1054.949360] dwc2 30180000.usb: req->length:66 req->actual:66 req->zero:1
[ 1054.949373] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.949405] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.949420] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.949436] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.949452] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=60000000
[ 1054.949464] dwc2 30180000.usb: zlp packet received
[ 1054.949482] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.949497] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.949513] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.949528] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.949540] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.949554] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.949567] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.949579] dwc2 30180000.usb: ep0 state:0
[ 1054.949591] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.949606] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.949641] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.949653] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.949668] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.949679] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.949698] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.949714] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0306, I=0409, L=00ff
[ 1054.949737] dwc2 30180000.usb: ep0: req e7f6a9ab: 26@abed5c1d,
noi=0, zero=1, snok=0
[ 1054.949754] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.949769] dwc2 30180000.usb: ureq->length:26 ureq->actual:0
[ 1054.949784] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@26/26,
0x0008001a => 0x00000910
[ 1054.949797] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.949809] dwc2 30180000.usb: ep0 state:1
[ 1054.949820] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.949834] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.949869] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.949881] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.949896] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.949911] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=00180034
[ 1054.949927] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 26
[ 1054.949939] dwc2 30180000.usb: req->length:26 req->actual:26 req->zero:1
[ 1054.949952] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.949985] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.949997] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.950012] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.950026] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=60000078
[ 1054.950036] dwc2 30180000.usb: zlp packet received
[ 1054.950052] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.950064] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.950080] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.950097] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.950111] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.950125] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.950137] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.950148] dwc2 30180000.usb: ep0 state:0
[ 1054.950159] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.950171] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.951154] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.951168] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.951184] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.951197] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.951216] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.951233] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0300, I=0000, L=00ff
[ 1054.951256] dwc2 30180000.usb: ep0: req e7f6a9ab: 4@abed5c1d,
noi=0, zero=1, snok=0
[ 1054.951276] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir in
[ 1054.951291] dwc2 30180000.usb: ureq->length:4 ureq->actual:0
[ 1054.951305] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@4/4,
0x00080004 => 0x00000910
[ 1054.951318] dwc2 30180000.usb: dwc2_hsotg_start_req: 67556000 pad
=> 0x00000914
[ 1054.951330] dwc2 30180000.usb: ep0 state:1
[ 1054.951343] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84028000
[ 1054.951357] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80008000
[ 1054.951393] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1054.951409] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000001
[ 1054.951427] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(in) DxEPINT=0x00000001
[ 1054.951442] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00008000, DXEPTSIZ=00100030
[ 1054.951460] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 4
[ 1054.951472] dwc2 30180000.usb: req->length:4 req->actual:4 req->zero:1
[ 1054.951486] dwc2 30180000.usb: Receiving zero-length packet on ep0
[ 1054.951519] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.951533] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.951551] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000001
[ 1054.951565] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00028000, DXEPTSIZ=40000070
[ 1054.951577] dwc2 30180000.usb: zlp packet received
[ 1054.951595] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
e7f6a9ab, 0 => a0d18b50
[ 1054.951609] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.951625] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.951641] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00028000, ep 0, dir out
[ 1054.951652] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.951666] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.951679] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.951689] dwc2 30180000.usb: ep0 state:0
[ 1054.951702] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80028000
[ 1054.951717] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80028000
[ 1054.951743] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.951756] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00010000
[ 1054.951772] dwc2 30180000.usb: dwc2_hsotg_epint: ep0(out) DxEPINT=0x00000009
[ 1054.951782] dwc2 30180000.usb: dwc2_hsotg_epint: Setup/Timeout
[ 1054.951800] dwc2 30180000.usb: complete: ep c20b8608 ep0, req
f2c3bdd7, 0 => 84063983
[ 1054.951816] dwc2 30180000.usb: ctrl Type=80, Req=06, V=0303, I=0409, L=00ff
[ 1054.951833] dwc2 30180000.usb: driver->setup() ret -22
[ 1054.951844] dwc2 30180000.usb: ep0 stall (dir=1)
[ 1054.951860] dwc2 30180000.usb: written DXEPCTL=0x04228000 to
00000900 (DXEPCTL=0x00208000)
[ 1054.951869] dwc2 30180000.usb: dwc2_hsotg_enqueue_setup: queueing
setup request
[ 1054.951885] dwc2 30180000.usb: ep0: req f2c3bdd7: 8@7d68f802,
noi=0, zero=0, snok=0
[ 1054.951900] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00228000, ep 0, dir out
[ 1054.951912] dwc2 30180000.usb: ureq->length:8 ureq->actual:0
[ 1054.951926] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@8/8,
0x00080008 => 0x00000b10
[ 1054.951938] dwc2 30180000.usb: dwc2_hsotg_start_req: 67558000 pad
=> 0x00000b14
[ 1054.951948] dwc2 30180000.usb: ep0 state:0
[ 1054.951959] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x80228000
[ 1054.951972] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80228000
[ 1054.952469] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1054.952482] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00040000
[ 1054.952498] dwc2 30180000.usb: dwc2_hsotg_epint: ep2(out) DxEPINT=0x00000001
[ 1054.952511] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00098200, DXEPTSIZ=13eedb02
[ 1054.952532] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
788a45df, 0 => 6513dd96
[ 1054.952564] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00098200, ep 2, dir out
[ 1054.952578] dwc2 30180000.usb: ureq->length:512 ureq->actual:0
[ 1054.952592] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@512/512,
0x00080200 => 0x00000b50
[ 1054.952605] dwc2 30180000.usb: dwc2_hsotg_start_req: 67102000 pad
=> 0x00000b54
[ 1054.952615] dwc2 30180000.usb: ep0 state:0
[ 1054.952626] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84098200
[ 1054.952638] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80098200
[ 1055.132227] dwc2 30180000.usb: ep2out: req 788a45df: 512@0542b9d7,
noi=0, zero=0, snok=0
[ 1055.187167] dwc2 30180000.usb: ep1in: req b3bab221: 353@8cbff1b5,
noi=0, zero=1, snok=0
[ 1055.187204] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x008a8200, ep 1, dir in
[ 1055.187223] dwc2 30180000.usb: ureq->length:353 ureq->actual:0
[ 1055.187246] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@353/353,
0x20080161 => 0x00000930
[ 1055.187265] dwc2 30180000.usb: dwc2_hsotg_start_req: 67101000 pad
=> 0x00000934
[ 1055.187279] dwc2 30180000.usb: ep0 state:0
[ 1055.187290] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x848a8200
[ 1055.187304] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80888200
[ 1055.187350] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1055.187370] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000002
[ 1055.187394] dwc2 30180000.usb: dwc2_hsotg_epint: ep1(in) DxEPINT=0x00000001
[ 1055.187413] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00898200, DXEPTSIZ=14be0de5
[ 1055.187432] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 353
[ 1055.187448] dwc2 30180000.usb: req->length:353 req->actual:353 req->zero:1
[ 1055.187469] dwc2 30180000.usb: complete: ep 4ee0de58 ep1in, req
b3bab221, 0 => b0bb1e62
[ 1055.290485] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1055.290506] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00040000
[ 1055.290529] dwc2 30180000.usb: dwc2_hsotg_epint: ep2(out) DxEPINT=0x00000001
[ 1055.290550] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00088200, DXEPTSIZ=13e6da40
[ 1055.290583] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
a40532cf, 0 => 6513dd96
[ 1055.290645] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00088200, ep 2, dir out
[ 1055.290662] dwc2 30180000.usb: ureq->length:512 ureq->actual:0
[ 1055.290682] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@512/512,
0x00080200 => 0x00000b50
[ 1055.290700] dwc2 30180000.usb: dwc2_hsotg_start_req: 67102000 pad
=> 0x00000b54
[ 1055.290714] dwc2 30180000.usb: ep0 state:0
[ 1055.290726] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84088200
[ 1055.290742] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80088200
[ 1055.290897] dwc2 30180000.usb: ep2out: req a40532cf: 512@51b87fad,
noi=0, zero=0, snok=0
[ 1055.346177] dwc2 30180000.usb: ep1in: req b3bab221: 353@8cbff1b5,
noi=0, zero=1, snok=0
[ 1055.346213] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00898200, ep 1, dir in
[ 1055.346231] dwc2 30180000.usb: ureq->length:353 ureq->actual:0
[ 1055.346252] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@353/353,
0x20080161 => 0x00000930
[ 1055.346273] dwc2 30180000.usb: dwc2_hsotg_start_req: 67101000 pad
=> 0x00000934
[ 1055.346287] dwc2 30180000.usb: ep0 state:0
[ 1055.346299] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84898200
[ 1055.346316] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80898200
[ 1055.346364] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1055.346386] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000002
[ 1055.346409] dwc2 30180000.usb: dwc2_hsotg_epint: ep1(in) DxEPINT=0x00000001
[ 1055.346428] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00888200, DXEPTSIZ=14b60c84
[ 1055.346451] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 353
[ 1055.346465] dwc2 30180000.usb: req->length:353 req->actual:353 req->zero:1
[ 1055.346488] dwc2 30180000.usb: complete: ep 4ee0de58 ep1in, req
b3bab221, 0 => b0bb1e62
[ 1055.449424] dwc2 30180000.usb: dwc2_hsotg_irq: 04088028 00080000
(d88c3cc4) retry 8
[ 1055.449446] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00040000
[ 1055.449469] dwc2 30180000.usb: dwc2_hsotg_epint: ep2(out) DxEPINT=0x00000001
[ 1055.449489] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00098200, DXEPTSIZ=13ded97e
[ 1055.449523] dwc2 30180000.usb: complete: ep c5cae4f8 ep2out, req
b11aed86, 0 => 6513dd96
[ 1055.449583] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00098200, ep 2, dir out
[ 1055.449601] dwc2 30180000.usb: ureq->length:512 ureq->actual:0
[ 1055.449624] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@512/512,
0x00080200 => 0x00000b50
[ 1055.449642] dwc2 30180000.usb: dwc2_hsotg_start_req: 67102000 pad
=> 0x00000b54
[ 1055.449657] dwc2 30180000.usb: ep0 state:0
[ 1055.449668] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84098200
[ 1055.449684] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80098200
[ 1055.449841] dwc2 30180000.usb: ep2out: req b11aed86: 512@6ac5f592,
noi=0, zero=0, snok=0
[ 1055.504683] dwc2 30180000.usb: ep1in: req b3bab221: 352@8cbff1b5,
noi=0, zero=1, snok=0
[ 1055.504719] dwc2 30180000.usb: dwc2_hsotg_start_req:
DxEPCTL=0x00888200, ep 1, dir in
[ 1055.504737] dwc2 30180000.usb: ureq->length:352 ureq->actual:0
[ 1055.504760] dwc2 30180000.usb: dwc2_hsotg_start_req: 1@352/352,
0x20080160 => 0x00000930
[ 1055.504778] dwc2 30180000.usb: dwc2_hsotg_start_req: 67101000 pad
=> 0x00000934
[ 1055.504792] dwc2 30180000.usb: ep0 state:0
[ 1055.504803] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84888200
[ 1055.504817] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80888200
[ 1055.504865] dwc2 30180000.usb: dwc2_hsotg_irq: 04048028 00040000
(d88c3cc4) retry 8
[ 1055.504884] dwc2 30180000.usb: dwc2_hsotg_irq: daint=00000002
[ 1055.504909] dwc2 30180000.usb: dwc2_hsotg_epint: ep1(in) DxEPINT=0x00000001
[ 1055.504929] dwc2 30180000.usb: dwc2_hsotg_epint: XferCompl:
DxEPCTL=0x00898200, DXEPTSIZ=14ae0b24
[ 1055.504948] dwc2 30180000.usb: dwc2_hsotg_complete_in: adjusting
size done 0 => 352
[ 1055.504964] dwc2 30180000.usb: req->length:352 req->actual:352 req->zero:1
[ 1055.504985] dwc2 30180000.usb: complete: ep 4ee0de58 ep1in, req
b3bab221, 0 => b0bb1e62

> >> Please provide me dump of follow dwc2 debugfs's: regdump, hw_params, params.
> >
> > Do you want this on working and failing state or just the failing one?
> >
> After failing.

[root@rv1108 30180000.usb]# cat regdump
GOTGCTL = 0x000d0000
GOTGINT = 0x00000000
GAHBCFG = 0x0000002f
GUSBCFG = 0x4000140f
GRSTCTL = 0x80000400
GINTSTS = 0x04008028
GINTMSK = 0xd88c3cc4
GRXSTSR = 0xe1a60002
GRXFSIZ = 0x00000118
GNPTXFSIZ = 0x00100118
GNPTXSTS = 0x00080010
GI2CCTL = 0x00000000
GPVNDCTL = 0x00000000
GGPIO = 0x00000000
GUID = 0x32000001
GSNPSID = 0x4f54310a
GHWCFG1 = 0x00006664
GHWCFG2 = 0x228e2450
GHWCFG3 = 0x03cc90e8
GHWCFG4 = 0xdbf04030
GLPMCFG = 0x00000000
GPWRDN = 0x00600010
GDFIFOCFG = 0x039803cc
ADPCTL = 0x00000000
HPTXFSIZ = 0x00000000
DPTXFSIZN(1) = 0x01000128
DPTXFSIZN(2) = 0x00800228
DPTXFSIZN(3) = 0x008002a8
DPTXFSIZN(4) = 0x00400328
DPTXFSIZN(5) = 0x00200368
DPTXFSIZN(6) = 0x00100388
DPTXFSIZN(7) = 0x000003e8
DPTXFSIZN(8) = 0x000003a8
DPTXFSIZN(9) = 0x01000128
DPTXFSIZN(10) = 0x00800228
DPTXFSIZN(11) = 0x008002a8
DPTXFSIZN(12) = 0x00400328
DPTXFSIZN(13) = 0x00200368
DPTXFSIZN(14) = 0x00100388
DPTXFSIZN(15) = 0x000003e8
DCFG = 0x00840360
DCTL = 0x00000000
DSTS = 0x003bb600
DIEPMSK = 0x0000020f
DOEPMSK = 0x0000022f
DAINT = 0x00000000
DAINTMSK = 0x0005000b
DTKNQR1 = 0x00000000
DTKNQR2 = 0x00000000
DTKNQR3 = 0x0c100020
DTKNQR4 = 0x00000000
DVBUSDIS = 0x00000b8f
DVBUSPULSE = 0x000002c6
DIEPCTL(0) = 0x00208000
DIEPCTL(1) = 0x00898200
DIEPCTL(2) = 0x00020400
DIEPCTL(3) = 0x018c800a
DIEPCTL(4) = 0x00020400
DIEPCTL(5) = 0x00020400
DIEPCTL(6) = 0x00020400
DIEPCTL(7) = 0x00020400
DIEPCTL(8) = 0x00020400
DIEPCTL(9) = 0x00020400
DIEPCTL(10) = 0x00020400
DIEPCTL(11) = 0x00020400
DIEPCTL(12) = 0x00020400
DIEPCTL(13) = 0x00020400
DIEPCTL(14) = 0x00020400
DIEPCTL(15) = 0x00020400
DOEPCTL(0) = 0x80228000
DOEPCTL(1) = 0x00020400
DOEPCTL(2) = 0x80098200
DOEPCTL(3) = 0x00020400
DOEPCTL(4) = 0x00020400
DOEPCTL(5) = 0x00020400
DOEPCTL(6) = 0x00020400
DOEPCTL(7) = 0x00020400
DOEPCTL(8) = 0x00020400
DOEPCTL(9) = 0x00020400
DOEPCTL(10) = 0x00020400
DOEPCTL(11) = 0x00020400
DOEPCTL(12) = 0x00020400
DOEPCTL(13) = 0x00020400
DOEPCTL(14) = 0x00020400
DOEPCTL(15) = 0x00020400
DIEPINT(0) = 0x00002090
DIEPINT(1) = 0x00002090
DIEPINT(2) = 0x00000080
DIEPINT(3) = 0x00000080
DIEPINT(4) = 0x00000080
DIEPINT(5) = 0x00000080
DIEPINT(6) = 0x00000080
DIEPINT(7) = 0x00000080
DIEPINT(8) = 0x00000080
DIEPINT(9) = 0x00000080
DIEPINT(10) = 0x00000080
DIEPINT(11) = 0x00000080
DIEPINT(12) = 0x00000080
DIEPINT(13) = 0x00000080
DIEPINT(14) = 0x00000080
DIEPINT(15) = 0x00000080
DOEPINT(0) = 0x00002010
DOEPINT(1) = 0x00000000
DOEPINT(2) = 0x00000000
DOEPINT(3) = 0x00000000
DOEPINT(4) = 0x00000000
DOEPINT(5) = 0x00000000
DOEPINT(6) = 0x00000000
DOEPINT(7) = 0x00000000
DOEPINT(8) = 0x00000000
DOEPINT(9) = 0x00000000
DOEPINT(10) = 0x00000000
DOEPINT(11) = 0x00000000
DOEPINT(12) = 0x00000000
DOEPINT(13) = 0x00000000
DOEPINT(14) = 0x00000000
DOEPINT(15) = 0x00000000
DIEPTSIZ(0) = 0x00100030
DIEPTSIZ(1) = 0x14ae0b24
DIEPTSIZ(2) = 0x00000000
DIEPTSIZ(3) = 0x0007fce0
DIEPTSIZ(4) = 0x00000000
DIEPTSIZ(5) = 0x00000000
DIEPTSIZ(6) = 0x00000000
DIEPTSIZ(7) = 0x00000000
DIEPTSIZ(8) = 0x00000000
DIEPTSIZ(9) = 0x00000000
DIEPTSIZ(10) = 0x00000000
DIEPTSIZ(11) = 0x00000000
DIEPTSIZ(12) = 0x00000000
DIEPTSIZ(13) = 0x00000000
DIEPTSIZ(14) = 0x00000000
DIEPTSIZ(15) = 0x00000000
DOEPTSIZ(0) = 0x20000068
DOEPTSIZ(1) = 0x00000000
DOEPTSIZ(2) = 0x13ded97e
DOEPTSIZ(3) = 0x00000000
DOEPTSIZ(4) = 0x00000000
DOEPTSIZ(5) = 0x00000000
DOEPTSIZ(6) = 0x00000000
DOEPTSIZ(7) = 0x00000000
DOEPTSIZ(8) = 0x00000000
DOEPTSIZ(9) = 0x00000000
DOEPTSIZ(10) = 0x00000000
DOEPTSIZ(11) = 0x00000000
DOEPTSIZ(12) = 0x00000000
DOEPTSIZ(13) = 0x00000000
DOEPTSIZ(14) = 0x00000000
DOEPTSIZ(15) = 0x00000000
DIEPDMA(0) = 0x67556000
DIEPDMA(1) = 0x547e49a0
DIEPDMA(2) = 0x3c23f762
DIEPDMA(3) = 0x5fffa83a
DIEPDMA(4) = 0x3c23f762
DIEPDMA(5) = 0x9526fdc6
DIEPDMA(6) = 0x3c23f762
DIEPDMA(7) = 0x943260eb
DIEPDMA(8) = 0x63d0d24e
DIEPDMA(9) = 0xfa5165f4
DIEPDMA(10) = 0x3c23f762
DIEPDMA(11) = 0x3c23f762
DIEPDMA(12) = 0x3c23f762
DIEPDMA(13) = 0x3c23f762
DIEPDMA(14) = 0x3c23f762
DIEPDMA(15) = 0x3c23f762
DOEPDMA(0) = 0xa32822e3
DOEPDMA(1) = 0xad4e6d7d
DOEPDMA(2) = 0x0ad3d634
DOEPDMA(3) = 0xad4e6d7d
DOEPDMA(4) = 0x0d62a196
DOEPDMA(5) = 0xad4e6d7d
DOEPDMA(6) = 0x07286ede
DOEPDMA(7) = 0xad4e6d7d
DOEPDMA(8) = 0x8b00e8e1
DOEPDMA(9) = 0x3ed6811f
DOEPDMA(10) = 0xad4e6d7d
DOEPDMA(11) = 0xad4e6d7d
DOEPDMA(12) = 0xad4e6d7d
DOEPDMA(13) = 0xad4e6d7d
DOEPDMA(14) = 0xad4e6d7d
DOEPDMA(15) = 0xad4e6d7d
DTXFSTS(0) = 0x00000010
DTXFSTS(1) = 0x00000080
DTXFSTS(2) = 0x00000010
DTXFSTS(3) = 0x0000000d
DTXFSTS(4) = 0x00000010
DTXFSTS(5) = 0x00000010
DTXFSTS(6) = 0x00000010
DTXFSTS(7) = 0x00000010
DTXFSTS(8) = 0x00000010
DTXFSTS(9) = 0x00000010
DTXFSTS(10) = 0x00000010
DTXFSTS(11) = 0x00000010
DTXFSTS(12) = 0x00000010
DTXFSTS(13) = 0x00000010
DTXFSTS(14) = 0x00000010
DTXFSTS(15) = 0x00000010
PCGCTL = 0x00000000
HCFG = 0x00840360
HFIR = 0x00000b8f
HFNUM = 0x50f90776
HPTXSTS = 0x00080100
HAINT = 0x00000000
HAINTMSK = 0x00000007
HFLBADDR = 0x00000000
HPRT0 = 0x00000000
HCCHAR(0) = 0x00898200
HCCHAR(1) = 0x00020400
HCCHAR(2) = 0x80098200
HCCHAR(3) = 0x00020400
HCCHAR(4) = 0x00020400
HCCHAR(5) = 0x00020400
HCCHAR(6) = 0x00020400
HCCHAR(7) = 0x00020400
HCCHAR(8) = 0x00020400
HCCHAR(9) = 0x00020400
HCCHAR(10) = 0x00020400
HCCHAR(11) = 0x00020400
HCCHAR(12) = 0x00020400
HCCHAR(13) = 0x00020400
HCCHAR(14) = 0x00020400
HCCHAR(15) = 0x00020400
HCSPLT(0) = 0x00000000
HCSPLT(1) = 0x00000000
HCSPLT(2) = 0x00000000
HCSPLT(3) = 0x00000000
HCSPLT(4) = 0x00000000
HCSPLT(5) = 0x00000000
HCSPLT(6) = 0x00000000
HCSPLT(7) = 0x00000000
HCSPLT(8) = 0x00000000
HCSPLT(9) = 0x00000000
HCSPLT(10) = 0x00000000
HCSPLT(11) = 0x00000000
HCSPLT(12) = 0x00000000
HCSPLT(13) = 0x00000000
HCSPLT(14) = 0x00000000
HCSPLT(15) = 0x00000000
HCINT(0) = 0x00002010
HCINT(1) = 0x00000000
HCINT(2) = 0x00000000
HCINT(3) = 0x00000000
HCINT(4) = 0x00000000
HCINT(5) = 0x00000000
HCINT(6) = 0x00000000
HCINT(7) = 0x00000000
HCINT(8) = 0x00000000
HCINT(9) = 0x00000000
HCINT(10) = 0x00000000
HCINT(11) = 0x00000000
HCINT(12) = 0x00000000
HCINT(13) = 0x00000000
HCINT(14) = 0x00000000
HCINT(15) = 0x00000000
HCINTMSK(0) = 0x0000020f
HCINTMSK(1) = 0x00000000
HCINTMSK(2) = 0x00000000
HCINTMSK(3) = 0x00000000
HCINTMSK(4) = 0x00000000
HCINTMSK(5) = 0x00000000
HCINTMSK(6) = 0x00000000
HCINTMSK(7) = 0x00000000
HCINTMSK(8) = 0x00000000
HCINTMSK(9) = 0x00000000
HCINTMSK(10) = 0x00000000
HCINTMSK(11) = 0x00000000
HCINTMSK(12) = 0x00000000
HCINTMSK(13) = 0x00000000
HCINTMSK(14) = 0x00000000
HCINTMSK(15) = 0x00000000
HCTSIZ(0) = 0x14ae0b24
HCTSIZ(1) = 0x00000000
HCTSIZ(2) = 0x13ded97e
HCTSIZ(3) = 0x00000000
HCTSIZ(4) = 0x00000000
HCTSIZ(5) = 0x00000000
HCTSIZ(6) = 0x00000000
HCTSIZ(7) = 0x00000000
HCTSIZ(8) = 0x00000000
HCTSIZ(9) = 0x00000000
HCTSIZ(10) = 0x00000000
HCTSIZ(11) = 0x00000000
HCTSIZ(12) = 0x00000000
HCTSIZ(13) = 0x00000000
HCTSIZ(14) = 0x00000000
HCTSIZ(15) = 0x00000000
HCDMA(0) = 0xa32822e3
HCDMA(1) = 0xad4e6d7d
HCDMA(2) = 0x0ad3d634
HCDMA(3) = 0xad4e6d7d
HCDMA(4) = 0x0d62a196
HCDMA(5) = 0xad4e6d7d
HCDMA(6) = 0x07286ede
HCDMA(7) = 0xad4e6d7d
HCDMA(8) = 0x8b00e8e1
HCDMA(9) = 0x3ed6811f
HCDMA(10) = 0xad4e6d7d
HCDMA(11) = 0xad4e6d7d
HCDMA(12) = 0xad4e6d7d
HCDMA(13) = 0xad4e6d7d
HCDMA(14) = 0xad4e6d7d
HCDMA(15) = 0xad4e6d7d
HCDMAB(0) = 0x60068ee1
HCDMAB(1) = 0xc08782bb
HCDMAB(2) = 0xca6a7f91
HCDMAB(3) = 0xc08782bb
HCDMAB(4) = 0xdde691d4
HCDMAB(5) = 0xc08782bb
HCDMAB(6) = 0x97489e9b
HCDMAB(7) = 0xc08782bb
HCDMAB(8) = 0xa71f3fe5
HCDMAB(9) = 0x6cb816bb
HCDMAB(10) = 0xc08782bb
HCDMAB(11) = 0xc08782bb
HCDMAB(12) = 0xc08782bb
HCDMAB(13) = 0xc08782bb
HCDMAB(14) = 0xc08782bb
HCDMAB(15) = 0xc08782bb

[root@rv1108 30180000.usb]# cat hw_params
op_mode                       : 0
arch                          : 2
dma_desc_enable               : 1
enable_dynamic_fifo           : 1
en_multiple_tx_fifo           : 1
rx_fifo_size                  : 1024
host_nperio_tx_fifo_size      : 0
dev_nperio_tx_fifo_size       : 16
host_perio_tx_fifo_size       : 0
nperio_tx_q_depth             : 4
host_perio_tx_q_depth         : 4
dev_token_q_depth             : 8
max_transfer_size             : 524287
max_packet_count              : 1023
host_channels                 : 9
hs_phy_type                   : 1
fs_phy_type                   : 0
i2c_enable                    : 0
num_dev_ep                    : 9
num_dev_perio_in_ep           : 0
total_fifo_size               : 972
power_optimized               : 1
utmi_phy_data_width           : 1
snpsid                        : 0x4f54310a
dev_ep_dirs                   : 0x6664

[root@rv1108 30180000.usb]# cat params
otg_cap                       : 2
dma_desc_enable               : 0
dma_desc_fs_enable            : 0
speed                         : 0
enable_dynamic_fifo           : 1
en_multiple_tx_fifo           : 1
host_rx_fifo_size             : 525
host_nperio_tx_fifo_size      : 128
host_perio_tx_fifo_size       : 256
max_transfer_size             : 524287
max_packet_count              : 1023
host_channels                 : 0
phy_type                      : 1
phy_utmi_width                : 16
phy_ulpi_ddr                  : 0
phy_ulpi_ext_vbus             : 0
i2c_enable                    : 0
ipg_isoc_en                   : 0
ulpi_fs_ls                    : 0
host_support_fs_ls_low_power  : 0
host_ls_low_power_phy_clk     : 0
ts_dline                      : 0
reload_ctl                    : 1
ahbcfg                        : 0xe
uframe_sched                  : 1
external_id_pin_ctl           : 0
power_down                    : 0
lpm                           : 0
lpm_clock_gating              : 0
besl                          : 0
hird_threshold_en             : 0
hird_threshold                : 4
service_interval              : 0
host_dma                      : 0
g_dma                         : 1
g_dma_desc                    : 1
g_rx_fifo_size                : 280
g_np_tx_fifo_size             : 16
g_tx_fifo_size[0]             : 0
g_tx_fifo_size[1]             : 256
g_tx_fifo_size[2]             : 128
g_tx_fifo_size[3]             : 128
g_tx_fifo_size[4]             : 64
g_tx_fifo_size[5]             : 32
g_tx_fifo_size[6]             : 16
g_tx_fifo_size[7]             : 0
g_tx_fifo_size[8]             : 0
g_tx_fifo_size[9]             : 0
g_tx_fifo_size[10]            : 0
g_tx_fifo_size[11]            : 0
g_tx_fifo_size[12]            : 0
g_tx_fifo_size[13]            : 0
g_tx_fifo_size[14]            : 0
g_tx_fifo_size[15]            : 0

Is this information you need? If need we can gather more info.

-- 
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://code.ossystems.com.br
Mobile: +55 (53) 9 9981-7854          Mobile: +1 (347) 903-9750

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-17 19:53       ` Otavio Salvador
@ 2020-02-19 12:26         ` Minas Harutyunyan
  2020-02-19 15:10           ` Otavio Salvador
  0 siblings, 1 reply; 11+ messages in thread
From: Minas Harutyunyan @ 2020-02-19 12:26 UTC (permalink / raw)
  To: Otavio Salvador, Minas Harutyunyan
  Cc: Greg Kroah-Hartman, linux-usb, Felipe Balbi, Heiko Stuebner,
	linux-rockchip, Johan Hovold

Hi Otavio,

On 2/17/2020 11:53 PM, Otavio Salvador wrote:
> Hello Minas,
> 
> On Mon, Feb 17, 2020 at 10:26 AM Minas Harutyunyan
> <Minas.Harutyunyan@synopsys.com> wrote:
>> Enable debug prints to get full dwc2 debug prints to see what happen
>> with dwc2.
> 

> [ 1054.529774] dwc2 30180000.usb: ep0 state:0
> [ 1054.529785] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84088200
> [ 1054.529801] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80088200
> [ 1054.529928] dwc2 30180000.usb: ep2out: req 26bd9b9f: 512@06b7dbca,
> noi=0, zero=0, snok=0
> [ 1054.537095] dwc2 30180000.usb: dwc2_hsotg_irq: 04008428 00000400
> (d88c3cc4) retry 8
> [ 1054.537119] dwc2 30180000.usb: GINTSTS_ErlySusp
> [ 1054.540147] dwc2 30180000.usb: gintsts=04008828  gintmsk=d88c3cc4
> [ 1054.540172] dwc2 30180000.usb: USB SUSPEND
> [ 1054.540191] dwc2 30180000.usb: dwc2_handle_usb_suspend_intr: DSTS=0x5ad801
> [ 1054.540211] dwc2 30180000.usb: DSTS.Suspend Status=1 HWCFG4.Power
> Optimize=1 HWCFG4.Hibernation=0
> [ 1054.540242] dwc2 30180000.usb: dwc2_hsotg_irq: 04008028 00000000
> (d88c3cc4) retry 8
> [ 1054.585402] dwc2 30180000.usb: ep1in: req 01eff31b: 353@bf8d62d8,
> noi=0, zero=1, snok=0
> [ 1054.585422] dwc2 30180000.usb: dwc2_hsotg_ep_queue: submit request
> only in active state
> [ 1054.661667] dwc2 30180000.usb: dwc2_hsotg_irq: 04008428 00000400
> (d88c3cc4) retry 8
> [ 1054.661694] dwc2 30180000.usb: GINTSTS_ErlySusp
> [ 1054.664715] dwc2 30180000.usb: gintsts=04008828  gintmsk=d88c3cc4
> [ 1054.664741] dwc2 30180000.usb: USB SUSPEND
> [ 1054.664760] dwc2 30180000.usb: dwc2_handle_usb_suspend_intr: DSTS=0x5ad801
> [ 1054.664781] dwc2 30180000.usb: DSTS.Suspend Status=1 HWCFG4.Power
> 

Actually, I don't see any issue with dwc2 from the log. Only not clear 
why SUSPEND happen hear. Is it because of disconnect/connect or 
reloading g_serial?
Is this log recorded when issue seen?
Anyway, before SUSPEND and after dwc2 successfully perform transfers on 
all EP's - ep1in bulk, ep2out bulk and ep3in interrupt.
Can you provide dmesg with dwc2 debug prints with exception case inside.

> Is this information you need? If need we can gather more info.
> 


Thanks,
Minas

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-19 12:26         ` Minas Harutyunyan
@ 2020-02-19 15:10           ` Otavio Salvador
  2020-02-20  6:59             ` Minas Harutyunyan
  0 siblings, 1 reply; 11+ messages in thread
From: Otavio Salvador @ 2020-02-19 15:10 UTC (permalink / raw)
  To: Minas Harutyunyan
  Cc: Greg Kroah-Hartman, linux-usb, Felipe Balbi, Heiko Stuebner,
	linux-rockchip, Johan Hovold

Hello Minas,

On Wed, Feb 19, 2020 at 9:26 AM Minas Harutyunyan
<Minas.Harutyunyan@synopsys.com> wrote:
> On 2/17/2020 11:53 PM, Otavio Salvador wrote:
> > On Mon, Feb 17, 2020 at 10:26 AM Minas Harutyunyan
> > <Minas.Harutyunyan@synopsys.com> wrote:
> >> Enable debug prints to get full dwc2 debug prints to see what happen
> >> with dwc2.
>
> > [ 1054.529774] dwc2 30180000.usb: ep0 state:0
> > [ 1054.529785] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84088200
> > [ 1054.529801] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80088200
> > [ 1054.529928] dwc2 30180000.usb: ep2out: req 26bd9b9f: 512@06b7dbca,
> > noi=0, zero=0, snok=0
> > [ 1054.537095] dwc2 30180000.usb: dwc2_hsotg_irq: 04008428 00000400
> > (d88c3cc4) retry 8
> > [ 1054.537119] dwc2 30180000.usb: GINTSTS_ErlySusp
> > [ 1054.540147] dwc2 30180000.usb: gintsts=04008828  gintmsk=d88c3cc4
> > [ 1054.540172] dwc2 30180000.usb: USB SUSPEND
> > [ 1054.540191] dwc2 30180000.usb: dwc2_handle_usb_suspend_intr: DSTS=0x5ad801
> > [ 1054.540211] dwc2 30180000.usb: DSTS.Suspend Status=1 HWCFG4.Power
> > Optimize=1 HWCFG4.Hibernation=0
> > [ 1054.540242] dwc2 30180000.usb: dwc2_hsotg_irq: 04008028 00000000
> > (d88c3cc4) retry 8
> > [ 1054.585402] dwc2 30180000.usb: ep1in: req 01eff31b: 353@bf8d62d8,
> > noi=0, zero=1, snok=0
> > [ 1054.585422] dwc2 30180000.usb: dwc2_hsotg_ep_queue: submit request
> > only in active state
> > [ 1054.661667] dwc2 30180000.usb: dwc2_hsotg_irq: 04008428 00000400
> > (d88c3cc4) retry 8
> > [ 1054.661694] dwc2 30180000.usb: GINTSTS_ErlySusp
> > [ 1054.664715] dwc2 30180000.usb: gintsts=04008828  gintmsk=d88c3cc4
> > [ 1054.664741] dwc2 30180000.usb: USB SUSPEND
> > [ 1054.664760] dwc2 30180000.usb: dwc2_handle_usb_suspend_intr: DSTS=0x5ad801
> > [ 1054.664781] dwc2 30180000.usb: DSTS.Suspend Status=1 HWCFG4.Power
> >
>
> Actually, I don't see any issue with dwc2 from the log. Only not clear
> why SUSPEND happen hear. Is it because of disconnect/connect or
> reloading g_serial?
> Is this log recorded when issue seen?

Yes, the log was recorded however we did not reload the g_serial
module. So when we gathered the logs, it was stuck.

> Anyway, before SUSPEND and after dwc2 successfully perform transfers on
> all EP's - ep1in bulk, ep2out bulk and ep3in interrupt.
> Can you provide dmesg with dwc2 debug prints with exception case inside.

The log I sent was taken with:

1) boot device
2) ran 'dmesg -c' so we cleaned the old messages
3) cause the lock up to happen
4) gather dmesg output

What sequence do you want us to do?
--
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://code.ossystems.com.br
Mobile: +55 (53) 9 9981-7854          Mobile: +1 (347) 903-9750

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-19 15:10           ` Otavio Salvador
@ 2020-02-20  6:59             ` Minas Harutyunyan
  2020-02-20 13:16               ` Otavio Salvador
  0 siblings, 1 reply; 11+ messages in thread
From: Minas Harutyunyan @ 2020-02-20  6:59 UTC (permalink / raw)
  To: Otavio Salvador, Minas Harutyunyan
  Cc: Greg Kroah-Hartman, linux-usb, Felipe Balbi, Heiko Stuebner,
	linux-rockchip, Johan Hovold

Hi Otavio,


On 2/19/2020 7:10 PM, Otavio Salvador wrote:
> Hello Minas,
> 
> On Wed, Feb 19, 2020 at 9:26 AM Minas Harutyunyan
> <Minas.Harutyunyan@synopsys.com> wrote:
>> On 2/17/2020 11:53 PM, Otavio Salvador wrote:
>>> On Mon, Feb 17, 2020 at 10:26 AM Minas Harutyunyan
>>> <Minas.Harutyunyan@synopsys.com> wrote:
>>>> Enable debug prints to get full dwc2 debug prints to see what happen
>>>> with dwc2.
>>
>>> [ 1054.529774] dwc2 30180000.usb: ep0 state:0
>>> [ 1054.529785] dwc2 30180000.usb: dwc2_hsotg_start_req: DxEPCTL=0x84088200
>>> [ 1054.529801] dwc2 30180000.usb: dwc2_hsotg_start_req: DXEPCTL=0x80088200
>>> [ 1054.529928] dwc2 30180000.usb: ep2out: req 26bd9b9f: 512@06b7dbca,
>>> noi=0, zero=0, snok=0
>>> [ 1054.537095] dwc2 30180000.usb: dwc2_hsotg_irq: 04008428 00000400
>>> (d88c3cc4) retry 8
>>> [ 1054.537119] dwc2 30180000.usb: GINTSTS_ErlySusp
>>> [ 1054.540147] dwc2 30180000.usb: gintsts=04008828  gintmsk=d88c3cc4
>>> [ 1054.540172] dwc2 30180000.usb: USB SUSPEND
>>> [ 1054.540191] dwc2 30180000.usb: dwc2_handle_usb_suspend_intr: DSTS=0x5ad801
>>> [ 1054.540211] dwc2 30180000.usb: DSTS.Suspend Status=1 HWCFG4.Power
>>> Optimize=1 HWCFG4.Hibernation=0
>>> [ 1054.540242] dwc2 30180000.usb: dwc2_hsotg_irq: 04008028 00000000
>>> (d88c3cc4) retry 8
>>> [ 1054.585402] dwc2 30180000.usb: ep1in: req 01eff31b: 353@bf8d62d8,
>>> noi=0, zero=1, snok=0
>>> [ 1054.585422] dwc2 30180000.usb: dwc2_hsotg_ep_queue: submit request
>>> only in active state
>>> [ 1054.661667] dwc2 30180000.usb: dwc2_hsotg_irq: 04008428 00000400
>>> (d88c3cc4) retry 8
>>> [ 1054.661694] dwc2 30180000.usb: GINTSTS_ErlySusp
>>> [ 1054.664715] dwc2 30180000.usb: gintsts=04008828  gintmsk=d88c3cc4
>>> [ 1054.664741] dwc2 30180000.usb: USB SUSPEND
>>> [ 1054.664760] dwc2 30180000.usb: dwc2_handle_usb_suspend_intr: DSTS=0x5ad801
>>> [ 1054.664781] dwc2 30180000.usb: DSTS.Suspend Status=1 HWCFG4.Power
>>>
>>
>> Actually, I don't see any issue with dwc2 from the log. Only not clear
>> why SUSPEND happen hear. Is it because of disconnect/connect or
>> reloading g_serial?
>> Is this log recorded when issue seen?
> 
> Yes, the log was recorded however we did not reload the g_serial
> module. So when we gathered the logs, it was stuck.
> 
>> Anyway, before SUSPEND and after dwc2 successfully perform transfers on
>> all EP's - ep1in bulk, ep2out bulk and ep3in interrupt.
>> Can you provide dmesg with dwc2 debug prints with exception case inside.
> 
> The log I sent was taken with:
> 
> 1) boot device
> 2) ran 'dmesg -c' so we cleaned the old messages
> 3) cause the lock up to happen
> 4) gather dmesg output
> 
> What sequence do you want us to do?

Yes. Can you provide also USB trace?

Thanks,
Minas


> --
> Otavio Salvador                             O.S. Systems
> https://urldefense.proofpoint.com/v2/url?u=http-3A__www.ossystems.com.br&d=DwIBaQ&c=DPL6_X_6JkXFx7AXWqB0tg&r=6z9Al9FrHR_ZqbbtSAsD16pvOL2S3XHxQnSzq8kusyI&m=LRZmjUC_RsqI1Ky9A0SkfCqicsDkCoHnGnXttwUlXec&s=815r-d3BXkFFJtIB2EQ8OA2fcr6ooNEpbYfvoARbD3s&e=         https://urldefense.proofpoint.com/v2/url?u=http-3A__code.ossystems.com.br&d=DwIBaQ&c=DPL6_X_6JkXFx7AXWqB0tg&r=6z9Al9FrHR_ZqbbtSAsD16pvOL2S3XHxQnSzq8kusyI&m=LRZmjUC_RsqI1Ky9A0SkfCqicsDkCoHnGnXttwUlXec&s=O1psrp_ccT1F6H678r50HId1cWn6g8UxKWstZ_kBzO8&e=
> Mobile: +55 (53) 9 9981-7854          Mobile: +1 (347) 903-9750
> 

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-20  6:59             ` Minas Harutyunyan
@ 2020-02-20 13:16               ` Otavio Salvador
  2020-02-21  6:52                 ` Minas Harutyunyan
  0 siblings, 1 reply; 11+ messages in thread
From: Otavio Salvador @ 2020-02-20 13:16 UTC (permalink / raw)
  To: Minas Harutyunyan
  Cc: Greg Kroah-Hartman, linux-usb, Felipe Balbi, Heiko Stuebner,
	linux-rockchip, Johan Hovold

Hello Minas,

Thanks for all your help on this, ...

On Thu, Feb 20, 2020 at 3:59 AM Minas Harutyunyan
<Minas.Harutyunyan@synopsys.com> wrote:
>
> On 2/19/2020 7:10 PM, Otavio Salvador wrote:
...
> > What sequence do you want us to do?
>
> Yes. Can you provide also USB trace?

I can, however, it is not clear to me what you want us to do.

Should we use, on host side, usbmon? or do you want something different?

-- 
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://code.ossystems.com.br
Mobile: +55 (53) 9 9981-7854          Mobile: +1 (347) 903-9750

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-20 13:16               ` Otavio Salvador
@ 2020-02-21  6:52                 ` Minas Harutyunyan
  2020-02-21 14:06                   ` Otavio Salvador
  0 siblings, 1 reply; 11+ messages in thread
From: Minas Harutyunyan @ 2020-02-21  6:52 UTC (permalink / raw)
  To: Otavio Salvador, Minas Harutyunyan
  Cc: Greg Kroah-Hartman, linux-usb, Felipe Balbi, Heiko Stuebner,
	linux-rockchip, Johan Hovold

Hi Otavio,

On 2/20/2020 5:16 PM, Otavio Salvador wrote:
> Hello Minas,
> 
> Thanks for all your help on this, ...
> 
> On Thu, Feb 20, 2020 at 3:59 AM Minas Harutyunyan
> <Minas.Harutyunyan@synopsys.com> wrote:
>>
>> On 2/19/2020 7:10 PM, Otavio Salvador wrote:
> ...
>>> What sequence do you want us to do?
>>
Please provide dwc2 debug log when stop working with g_serial exception 
dump inside.
Also provide dwc2 log when it's work without issue.

>> Yes. Can you provide also USB trace >
> I can, however, it is not clear to me what you want us to do.
> 
> Should we use, on host side, usbmon? or do you want something different?
> 
Do you have any USB tracer equipment to record trace between host and 
device?

Thanks,
Minas

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: USB DWC2 stops responding when insert/remove cable multiple times
  2020-02-21  6:52                 ` Minas Harutyunyan
@ 2020-02-21 14:06                   ` Otavio Salvador
  0 siblings, 0 replies; 11+ messages in thread
From: Otavio Salvador @ 2020-02-21 14:06 UTC (permalink / raw)
  To: Minas Harutyunyan
  Cc: Greg Kroah-Hartman, linux-usb, Felipe Balbi, Heiko Stuebner,
	linux-rockchip, Johan Hovold

Hello Minas,

On Fri, Feb 21, 2020 at 3:52 AM Minas Harutyunyan
<Minas.Harutyunyan@synopsys.com> wrote:
> On 2/20/2020 5:16 PM, Otavio Salvador wrote:
> > Hello Minas,
> >
> > Thanks for all your help on this, ...
> >
> > On Thu, Feb 20, 2020 at 3:59 AM Minas Harutyunyan
> > <Minas.Harutyunyan@synopsys.com> wrote:
> >>
> >> On 2/19/2020 7:10 PM, Otavio Salvador wrote:
> > ...
> >>> What sequence do you want us to do?
> >>
> Please provide dwc2 debug log when stop working with g_serial exception
> dump inside.
> Also provide dwc2 log when it's work without issue.

Attached.

> >> Yes. Can you provide also USB trace >
> > I can, however, it is not clear to me what you want us to do.
> >
> > Should we use, on host side, usbmon? or do you want something different?
> >
> Do you have any USB tracer equipment to record trace between host and
> device?

I don't. Can we instrument the kernel somehow to gather the info we need?

-- 
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://code.ossystems.com.br
Mobile: +55 (53) 9 9981-7854          Mobile: +1 (347) 903-9750

^ permalink raw reply	[flat|nested] 11+ messages in thread

end of thread, back to index

Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-02-14 13:40 USB DWC2 stops responding when insert/remove cable multiple times Otavio Salvador
2020-02-17  8:58 ` Minas Harutyunyan
2020-02-17 12:30   ` Otavio Salvador
2020-02-17 13:26     ` Minas Harutyunyan
2020-02-17 19:53       ` Otavio Salvador
2020-02-19 12:26         ` Minas Harutyunyan
2020-02-19 15:10           ` Otavio Salvador
2020-02-20  6:59             ` Minas Harutyunyan
2020-02-20 13:16               ` Otavio Salvador
2020-02-21  6:52                 ` Minas Harutyunyan
2020-02-21 14:06                   ` Otavio Salvador

Linux-USB Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-usb/0 linux-usb/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-usb linux-usb/ https://lore.kernel.org/linux-usb \
		linux-usb@vger.kernel.org
	public-inbox-index linux-usb

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-usb


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git