linux-watchdog.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Stefan Wahren <stefan.wahren@i2se.com>
To: Rob Herring <robh+dt@kernel.org>,
	Nicolas Saenz Julienne <nsaenz@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>,
	Ray Jui <rjui@broadcom.com>,
	Scott Branden <sbranden@broadcom.com>,
	bcm-kernel-feedback-list@broadcom.com,
	Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>,
	soc@kernel.org, Wim Van Sebroeck <wim@linux-watchdog.org>,
	Guenter Roeck <linux@roeck-us.net>,
	devicetree@vger.kernel.org, linux-rpi-kernel@lists.infradead.org,
	linux-arm-kernel@lists.infradead.org,
	linux-watchdog@vger.kernel.org,
	Stefan Wahren <stefan.wahren@i2se.com>
Subject: [PATCH 5/6] ARM: dts: Add Raspberry Pi 400 support
Date: Sun, 30 May 2021 11:26:14 +0200	[thread overview]
Message-ID: <1622366775-5309-6-git-send-email-stefan.wahren@i2se.com> (raw)
In-Reply-To: <1622366775-5309-1-git-send-email-stefan.wahren@i2se.com>

The Raspberry Pi 400 is like a Pi 4 B designed into a keyboard. But there
are some minor differences:

- higher CPU clock rate (1.8 GHz)
- different Wifi chip (BCM43456)
- power off is now handled via GPIO
- no ACT LED

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
 arch/arm/boot/dts/Makefile            |   1 +
 arch/arm/boot/dts/bcm2711-rpi-400.dts | 271 ++++++++++++++++++++++++++++++++++
 2 files changed, 272 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm2711-rpi-400.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f8f09c5..ec00dba 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -88,6 +88,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
 	bcm2837-rpi-cm3-io3.dtb \
+	bcm2711-rpi-400.dtb \
 	bcm2711-rpi-4-b.dtb \
 	bcm2835-rpi-zero.dtb \
 	bcm2835-rpi-zero-w.dtb
diff --git a/arch/arm/boot/dts/bcm2711-rpi-400.dts b/arch/arm/boot/dts/bcm2711-rpi-400.dts
new file mode 100644
index 0000000..f063c5e
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2711-rpi-400.dts
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711.dtsi"
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-usb-peripheral.dtsi"
+
+/ {
+	compatible = "raspberrypi,400", "brcm,bcm2711";
+	model = "Raspberry Pi 400";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	/* Will be filled by the bootloader */
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0>;
+	};
+
+	aliases {
+		ethernet0 = &genet;
+	};
+
+	leds {
+		/delete-node/ act;
+
+		led-pwr {
+			label = "PWR";
+			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&expgpio 5 GPIO_ACTIVE_HIGH>;
+	};
+
+	sd_io_1v8_reg: sd_io_1v8_reg {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-sd-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-settling-time-us = <5000>;
+		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+		status = "okay";
+	};
+
+	sd_vcc_reg: sd_vcc_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&ddc0 {
+	status = "okay";
+};
+
+&ddc1 {
+	status = "okay";
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "",
+				  "GLOBAL_RESET",
+				  "VDD_SD_IO_SEL",
+				  "CAM_GPIO",
+				  "SD_PWR_ON",
+				  "SD_OC_N";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "RGMII_MDIO",
+			  "RGMIO_MDC",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  /* Shared with SPI flash */
+			  "PWM0_MISO",
+			  "PWM1_MOSI",
+			  "STATUS_LED_G_CLK",
+			  "SPIFLASH_CE_N",
+			  "SDA0",
+			  "SCL0",
+			  "RGMII_RXCLK",
+			  "RGMII_RXCTL",
+			  "RGMII_RXD0",
+			  "RGMII_RXD1",
+			  "RGMII_RXD2",
+			  "RGMII_RXD3",
+			  "RGMII_TXCLK",
+			  "RGMII_TXCTL",
+			  "RGMII_TXD0",
+			  "RGMII_TXD1",
+			  "RGMII_TXD2",
+			  "RGMII_TXD3";
+};
+
+&hdmi0 {
+	status = "okay";
+};
+
+&hdmi1 {
+	status = "okay";
+};
+
+&pixelvalve0 {
+	status = "okay";
+};
+
+&pixelvalve1 {
+	status = "okay";
+};
+
+&pixelvalve2 {
+	status = "okay";
+};
+
+&pixelvalve4 {
+	status = "okay";
+};
+
+&pm {
+	/delete-property/ system-power-controller;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>;
+	status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* EMMC2 is used to drive the SD card */
+&emmc2 {
+	vqmmc-supply = <&sd_io_1v8_reg>;
+	vmmc-supply = <&sd_vcc_reg>;
+	broken-cd;
+	status = "okay";
+};
+
+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+&genet_mdio {
+	clock-frequency = <1950000>;
+
+	phy1: ethernet-phy@1 {
+		/* No PHY interrupt */
+		reg = <0x1>;
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&vc4 {
+	status = "okay";
+};
+
+&vec {
+	status = "disabled";
+};
-- 
2.7.4


  parent reply	other threads:[~2021-05-30  9:26 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-05-30  9:26 [PATCH 0/6] " Stefan Wahren
2021-05-30  9:26 ` [PATCH 1/6] ARM: dts: bcm283x: Fix up MMC node names Stefan Wahren
2021-05-30  9:26 ` [PATCH 2/6] watchdog: bcm2835_wdt: consider system-power-controller property Stefan Wahren
2021-06-02 10:37   ` Guenter Roeck
     [not found]   ` <e61ba6f5b906fd26a61e9c79ef4dcf4792a364d7.camel@kernel.org>
2021-06-02 10:40     ` Guenter Roeck
2021-05-30  9:26 ` [PATCH 3/6] ARM: dts: Move BCM2711 RPi specific into separate dtsi Stefan Wahren
     [not found]   ` <86a7cded6e3e17b0ab347e55b38a44e10bc4e46a.camel@kernel.org>
2021-06-01 18:51     ` Stefan Wahren
2021-05-30  9:26 ` [PATCH 4/6] dt-bindings: arm: bcm2835: Add Raspberry Pi 400 to DT schema Stefan Wahren
2021-06-04 21:31   ` Rob Herring
2021-05-30  9:26 ` Stefan Wahren [this message]
2021-05-30  9:26 ` [PATCH 6/6] arm64: dts: broadcom: Add reference to RPi 400 Stefan Wahren

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1622366775-5309-6-git-send-email-stefan.wahren@i2se.com \
    --to=stefan.wahren@i2se.com \
    --cc=arnd@arndb.de \
    --cc=bcm-kernel-feedback-list@broadcom.com \
    --cc=devicetree@vger.kernel.org \
    --cc=f.fainelli@gmail.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-rpi-kernel@lists.infradead.org \
    --cc=linux-watchdog@vger.kernel.org \
    --cc=linux@roeck-us.net \
    --cc=nsaenz@kernel.org \
    --cc=olof@lixom.net \
    --cc=rjui@broadcom.com \
    --cc=robh+dt@kernel.org \
    --cc=sbranden@broadcom.com \
    --cc=soc@kernel.org \
    --cc=wim@linux-watchdog.org \
    --subject='Re: [PATCH 5/6] ARM: dts: Add Raspberry Pi 400 support' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).