From: Eric Anholt <eric@anholt.net>
To: Florian Fainelli <f.fainelli@gmail.com>,
linux-watchdog@vger.kernel.org, devicetree@vger.kernel.org,
Guenter Roeck <linux@roeck-us.net>,
Wim Van Sebroeck <wim@linux-watchdog.org>,
Lee Jones <lee.jones@linaro.org>,
Stefan Wahren <stefan.wahren@i2se.com>,
Mark Rutland <mark.rutland@arm.com>,
Rob Herring <robh+dt@kernel.org>
Cc: linux-rpi-kernel@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
bcm-kernel-feedback-list@broadcom.com,
Eric Anholt <eric@anholt.net>
Subject: [PATCH v4 5/5] ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.
Date: Wed, 12 Dec 2018 15:51:50 -0800 [thread overview]
Message-ID: <20181212235150.6491-6-eric@anholt.net> (raw)
In-Reply-To: <20181212235150.6491-1-eric@anholt.net>
The GRAFX domain only contains V3D, and this driver should be the only
accessor of V3D (firmware usage gets disabled when V3D is in the DT),
so we can safely make Linux control the GRAFX and GRAFX_V3D power
domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
---
v4: no change
arch/arm/boot/dts/bcm2835-rpi.dtsi | 4 ----
arch/arm/boot/dts/bcm283x.dtsi | 4 +++-
2 files changed, 3 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index cb2d6d78a7fb..21a930148709 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -87,10 +87,6 @@
power-domains = <&power RPI_POWER_DOMAIN_USB>;
};
-&v3d {
- power-domains = <&power RPI_POWER_DOMAIN_V3D>;
-};
-
&hdmi {
power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
status = "okay";
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index 20ed8b1da11b..9777644c6c2b 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -3,6 +3,7 @@
#include <dt-bindings/clock/bcm2835-aux.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/soc/bcm2835-pm.h>
/* firmware-provided startup stubs live here, where the secondary CPUs are
* spinning.
@@ -120,7 +121,7 @@
#interrupt-cells = <2>;
};
- watchdog@7e100000 {
+ pm: watchdog@7e100000 {
compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
#power-domain-cells = <1>;
#reset-cells = <1>;
@@ -638,6 +639,7 @@
compatible = "brcm,bcm2835-v3d";
reg = <0x7ec00000 0x1000>;
interrupts = <1 10>;
+ power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
};
vc4: gpu {
--
2.20.0.rc1
next prev parent reply other threads:[~2018-12-12 23:52 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-12 23:51 [PATCH v4 0/5] BCM2835 PM driver Eric Anholt
2018-12-12 23:51 ` [PATCH v4 1/5] dt-bindings: soc: Add a new binding for the BCM2835 PM node. (v4) Eric Anholt
2018-12-12 23:51 ` [PATCH v4 2/5] bcm2835-pm: Move bcm2835-watchdog's DT probe to an MFD Eric Anholt
2018-12-12 23:51 ` [PATCH v4 3/5] soc: bcm: bcm2835-pm: Add support for power domains under a new binding Eric Anholt
2018-12-12 23:51 ` [PATCH v4 4/5] ARM: bcm283x: Extend the WDT DT node out to cover the whole PM block. (v4) Eric Anholt
2018-12-12 23:51 ` Eric Anholt [this message]
2019-01-03 15:56 ` [PATCH v4 0/5] BCM2835 PM driver Stefan Wahren
2019-01-09 19:00 ` Stefan Wahren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181212235150.6491-6-eric@anholt.net \
--to=eric@anholt.net \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=devicetree@vger.kernel.org \
--cc=f.fainelli@gmail.com \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=stefan.wahren@i2se.com \
--cc=wim@linux-watchdog.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).