Linux-Watchdog Archive on lore.kernel.org
 help / Atom feed
* [RFC PATCH v2 06/10] devicetree: bindings: Document first ROHM BD70528 bindings
@ 2019-01-25 11:04 Matti Vaittinen
  0 siblings, 0 replies; 1+ messages in thread
From: Matti Vaittinen @ 2019-01-25 11:04 UTC (permalink / raw)
  To: mazziesaccount, matti.vaittinen
  Cc: heikki.haikola, mikko.mutanen, lee.jones, robh+dt, mark.rutland,
	broonie, gregkh, rafael, mturquette, sboyd, linus.walleij,
	bgolaszewski, sre, lgirdwood, a.zummo, alexandre.belloni, wim,
	linux, devicetree, linux-kernel, linux-clk, linux-gpio, linux-pm,
	linux-rtc, linux-watchdog

Document bindings for regulators (3 bucks, 3 LDOs and 2 LED
drivers) and 4 GPIO pins which can be configured for I/O or
as interrupt sources withe configurable trigger levels.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
 .../devicetree/bindings/mfd/rohm,bd70528-pmic.txt  | 104 +++++++++++++++++++++
 1 file changed, 104 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt

diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt
new file mode 100644
index 000000000000..21801440a53a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd70528-pmic.txt
@@ -0,0 +1,104 @@
+* ROHM BD70528 Power Management Integrated Circuit bindings
+
+BD70528MWV is an ultra-low Iq general purpose single-chip power management IC
+for battery-powered portable devices. The IC integrates 3 ultra-low current
+consumption buck converters, 3 LDOs and 2 LED Drivers. Also included are 4
+GPIOs, a real-time clock (RTC), a 32kHz clock gate, high-accuracy VREF
+for use with an external ADC, flexible dual-input power path, 10 bits SAR ADC
+for battery temperature monitor and 1S battery charger with scalable charge
+currents.
+
+Required properties:
+ - compatible		: Should be "rohm,bd70528"
+ - reg			: I2C slave address.
+ - interrupt-parent	: Phandle to the parent interrupt controller.
+ - interrupts		: The interrupt line the device is connected to.
+ - interrupt-controller	: To indicate bd70528 acts as an interrupt controller.
+ - #interrupt-cells	: Should be 2. usage is compliant to the 2 cells
+			  variant of ../interrupt-controller/interrupts.txt
+ - gpio-controller	: To indicate bd70528 acts as a gpio controller.
+ - #gpio-cells		: Should be 2. The first cell is the pin number and
+			  the second cell is used to specify flags. See
+			  ../gpio/gpio.txt for more information.
+ - clock-frequency	: Should be 32768
+ - #clock-cells		: Should be 0.
+ - regulators:		: List of child nodes that specify the regulators.
+			  Please see ../regulator/rohm,bd70528-regulator.txt
+
+Optional properties:
+ - clock-output-names	: Should contain name for output clock.
+
+Example:
+/* external oscillator */
+osc: oscillator {
+	compatible = "fixed-clock";
+	#clock-cells = <1>;
+	clock-frequency  = <32768>;
+	clock-output-names = "osc";
+};
+
+pmic: bd70528@4b {
+	compatible = "rohm,bd70528";
+	reg = <0x4b>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <29 GPIO_ACTIVE_LOW>;
+	clocks = <&osc 0>;
+	#clock-cells = <0>;
+	clock-output-names = "bd70528-32k-out";
+	#gpio-cells = <2>;
+	gpio-controller;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	regulators {
+		buck1: BUCK1 {
+			regulator-name = "buck1";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-boot-on;
+			regulator-ramp-delay = <125>;
+		};
+		buck2: BUCK2 {
+			regulator-name = "buck2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-ramp-delay = <125>;
+		};
+		buck3: BUCK3 {
+			regulator-name = "buck3";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+			regulator-ramp-delay = <250>;
+		};
+		ldo1: LDO1 {
+			regulator-name = "ldo1";
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+		};
+		ldo2: LDO2 {
+			regulator-name = "ldo2";
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+		};
+
+		ldo3: LDO3 {
+			regulator-name = "ldo3";
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		led_ldo1: LED_LDO1 {
+			regulator-name = "led_ldo1";
+			regulator-min-microvolt = <200000>;
+			regulator-max-microvolt = <300000>;
+		};
+		led_ldo2: LED_LDO2 {
+			regulator-name = "led_ldo2";
+			regulator-min-microvolt = <200000>;
+			regulator-max-microvolt = <300000>;
+		};
+	};
+};
-- 
2.14.3


-- 
Matti Vaittinen
ROHM Semiconductors

~~~ "I don't think so," said Rene Descartes.  Just then, he vanished ~~~

^ permalink raw reply	[flat|nested] 1+ messages in thread

only message in thread, back to index

Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-01-25 11:04 [RFC PATCH v2 06/10] devicetree: bindings: Document first ROHM BD70528 bindings Matti Vaittinen

Linux-Watchdog Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-watchdog/0 linux-watchdog/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-watchdog linux-watchdog/ https://lore.kernel.org/linux-watchdog \
		linux-watchdog@vger.kernel.org linux-watchdog@archiver.kernel.org
	public-inbox-index linux-watchdog


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-watchdog


AGPL code for this site: git clone https://public-inbox.org/ public-inbox