* [PATCH] watchdog: qcom: add support for the bark interrupt
@ 2019-09-05 16:21 Jorge Ramirez-Ortiz
2019-09-05 16:39 ` Bjorn Andersson
0 siblings, 1 reply; 3+ messages in thread
From: Jorge Ramirez-Ortiz @ 2019-09-05 16:21 UTC (permalink / raw)
To: jorge.ramirez-ortiz, agross, wim
Cc: linux-arm-msm, linux-watchdog, linux-kernel, bjorn.andersson
Use the bark interrupt to notify the bark event. Since the bark and bite
timeouts are identical, increase the bite timeout by one second so
that the bark event can be logged to the console.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
---
drivers/watchdog/qcom-wdt.c | 42 ++++++++++++++++++++++++++++++++++---
1 file changed, 39 insertions(+), 3 deletions(-)
diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
index 7be7f87be28f..5eaf92084b93 100644
--- a/drivers/watchdog/qcom-wdt.c
+++ b/drivers/watchdog/qcom-wdt.c
@@ -10,6 +10,7 @@
#include <linux/platform_device.h>
#include <linux/watchdog.h>
#include <linux/of_device.h>
+#include <linux/interrupt.h>
enum wdt_reg {
WDT_RST,
@@ -41,6 +42,8 @@ struct qcom_wdt {
unsigned long rate;
void __iomem *base;
const u32 *layout;
+ unsigned int irq;
+ const struct device *dev;
};
static void __iomem *wdt_addr(struct qcom_wdt *wdt, enum wdt_reg reg)
@@ -54,15 +57,37 @@ struct qcom_wdt *to_qcom_wdt(struct watchdog_device *wdd)
return container_of(wdd, struct qcom_wdt, wdd);
}
+static inline int qcom_wdt_enable(struct qcom_wdt *wdt)
+{
+ if (wdt->irq < 0)
+ return 1;
+
+ /* enable timeout with interrupt */
+ return 3;
+}
+
+static irqreturn_t qcom_wdt_irq(int irq, void *cookie)
+{
+ struct qcom_wdt *wdt = (struct qcom_wdt *) cookie;
+
+ dev_warn(wdt->dev, "barking, one second countdown to reset\n");
+
+ return IRQ_HANDLED;
+}
+
static int qcom_wdt_start(struct watchdog_device *wdd)
{
struct qcom_wdt *wdt = to_qcom_wdt(wdd);
+ unsigned int bark, bite;
+
+ bark = wdd->timeout;
+ bite = wdt->irq < 0 ? bark : bark + 1;
writel(0, wdt_addr(wdt, WDT_EN));
writel(1, wdt_addr(wdt, WDT_RST));
- writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
- writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
- writel(1, wdt_addr(wdt, WDT_EN));
+ writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
+ writel(bite * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
+ writel(qcom_wdt_enable(wdt), wdt_addr(wdt, WDT_EN));
return 0;
}
@@ -210,10 +235,21 @@ static int qcom_wdt_probe(struct platform_device *pdev)
wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
wdt->wdd.parent = dev;
wdt->layout = regs;
+ wdt->dev = &pdev->dev;
if (readl(wdt_addr(wdt, WDT_STS)) & 1)
wdt->wdd.bootstatus = WDIOF_CARDRESET;
+ wdt->irq = platform_get_irq(pdev, 0);
+ if (wdt->irq >= 0) {
+ ret = devm_request_irq(&pdev->dev, wdt->irq, qcom_wdt_irq,
+ IRQF_TRIGGER_RISING, "wdog_bark", wdt);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to request irq\n");
+ return ret;
+ }
+ }
+
/*
* If 'timeout-sec' unspecified in devicetree, assume a 30 second
* default, unless the max timeout is less than 30 seconds, then use
--
2.23.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] watchdog: qcom: add support for the bark interrupt
2019-09-05 16:21 [PATCH] watchdog: qcom: add support for the bark interrupt Jorge Ramirez-Ortiz
@ 2019-09-05 16:39 ` Bjorn Andersson
2019-09-05 16:48 ` Jorge Ramirez
0 siblings, 1 reply; 3+ messages in thread
From: Bjorn Andersson @ 2019-09-05 16:39 UTC (permalink / raw)
To: Jorge Ramirez-Ortiz
Cc: agross, wim, linux-arm-msm, linux-watchdog, linux-kernel
On Thu 05 Sep 09:21 PDT 2019, Jorge Ramirez-Ortiz wrote:
> Use the bark interrupt to notify the bark event. Since the bark and bite
> timeouts are identical, increase the bite timeout by one second so
> that the bark event can be logged to the console.
>
Afaict you should tie the bark to the "pretimeout" in the watchdog
framework , which would allow the user to specify a pretimeout and
configure what should happen at the bark (just a pr_alert() or panic()).
Regards,
Bjorn
> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> ---
> drivers/watchdog/qcom-wdt.c | 42 ++++++++++++++++++++++++++++++++++---
> 1 file changed, 39 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
> index 7be7f87be28f..5eaf92084b93 100644
> --- a/drivers/watchdog/qcom-wdt.c
> +++ b/drivers/watchdog/qcom-wdt.c
> @@ -10,6 +10,7 @@
> #include <linux/platform_device.h>
> #include <linux/watchdog.h>
> #include <linux/of_device.h>
> +#include <linux/interrupt.h>
>
> enum wdt_reg {
> WDT_RST,
> @@ -41,6 +42,8 @@ struct qcom_wdt {
> unsigned long rate;
> void __iomem *base;
> const u32 *layout;
> + unsigned int irq;
> + const struct device *dev;
> };
>
> static void __iomem *wdt_addr(struct qcom_wdt *wdt, enum wdt_reg reg)
> @@ -54,15 +57,37 @@ struct qcom_wdt *to_qcom_wdt(struct watchdog_device *wdd)
> return container_of(wdd, struct qcom_wdt, wdd);
> }
>
> +static inline int qcom_wdt_enable(struct qcom_wdt *wdt)
> +{
> + if (wdt->irq < 0)
> + return 1;
> +
> + /* enable timeout with interrupt */
> + return 3;
> +}
> +
> +static irqreturn_t qcom_wdt_irq(int irq, void *cookie)
> +{
> + struct qcom_wdt *wdt = (struct qcom_wdt *) cookie;
> +
> + dev_warn(wdt->dev, "barking, one second countdown to reset\n");
> +
> + return IRQ_HANDLED;
> +}
> +
> static int qcom_wdt_start(struct watchdog_device *wdd)
> {
> struct qcom_wdt *wdt = to_qcom_wdt(wdd);
> + unsigned int bark, bite;
> +
> + bark = wdd->timeout;
> + bite = wdt->irq < 0 ? bark : bark + 1;
>
> writel(0, wdt_addr(wdt, WDT_EN));
> writel(1, wdt_addr(wdt, WDT_RST));
> - writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
> - writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
> - writel(1, wdt_addr(wdt, WDT_EN));
> + writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
> + writel(bite * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
> + writel(qcom_wdt_enable(wdt), wdt_addr(wdt, WDT_EN));
> return 0;
> }
>
> @@ -210,10 +235,21 @@ static int qcom_wdt_probe(struct platform_device *pdev)
> wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
> wdt->wdd.parent = dev;
> wdt->layout = regs;
> + wdt->dev = &pdev->dev;
>
> if (readl(wdt_addr(wdt, WDT_STS)) & 1)
> wdt->wdd.bootstatus = WDIOF_CARDRESET;
>
> + wdt->irq = platform_get_irq(pdev, 0);
> + if (wdt->irq >= 0) {
> + ret = devm_request_irq(&pdev->dev, wdt->irq, qcom_wdt_irq,
> + IRQF_TRIGGER_RISING, "wdog_bark", wdt);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to request irq\n");
> + return ret;
> + }
> + }
> +
> /*
> * If 'timeout-sec' unspecified in devicetree, assume a 30 second
> * default, unless the max timeout is less than 30 seconds, then use
> --
> 2.23.0
>
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] watchdog: qcom: add support for the bark interrupt
2019-09-05 16:39 ` Bjorn Andersson
@ 2019-09-05 16:48 ` Jorge Ramirez
0 siblings, 0 replies; 3+ messages in thread
From: Jorge Ramirez @ 2019-09-05 16:48 UTC (permalink / raw)
To: Bjorn Andersson; +Cc: agross, wim, linux-arm-msm, linux-watchdog, linux-kernel
On 9/5/19 18:39, Bjorn Andersson wrote:
> On Thu 05 Sep 09:21 PDT 2019, Jorge Ramirez-Ortiz wrote:
>
>> Use the bark interrupt to notify the bark event. Since the bark and bite
>> timeouts are identical, increase the bite timeout by one second so
>> that the bark event can be logged to the console.
>>
>
> Afaict you should tie the bark to the "pretimeout" in the watchdog
> framework , which would allow the user to specify a pretimeout and
> configure what should happen at the bark (just a pr_alert() or panic()).
yes, you are right. will send v2 based on this.
thanks!
>
> Regards,
> Bjorn
>
>> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
>> ---
>> drivers/watchdog/qcom-wdt.c | 42 ++++++++++++++++++++++++++++++++++---
>> 1 file changed, 39 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
>> index 7be7f87be28f..5eaf92084b93 100644
>> --- a/drivers/watchdog/qcom-wdt.c
>> +++ b/drivers/watchdog/qcom-wdt.c
>> @@ -10,6 +10,7 @@
>> #include <linux/platform_device.h>
>> #include <linux/watchdog.h>
>> #include <linux/of_device.h>
>> +#include <linux/interrupt.h>
>>
>> enum wdt_reg {
>> WDT_RST,
>> @@ -41,6 +42,8 @@ struct qcom_wdt {
>> unsigned long rate;
>> void __iomem *base;
>> const u32 *layout;
>> + unsigned int irq;
>> + const struct device *dev;
>> };
>>
>> static void __iomem *wdt_addr(struct qcom_wdt *wdt, enum wdt_reg reg)
>> @@ -54,15 +57,37 @@ struct qcom_wdt *to_qcom_wdt(struct watchdog_device *wdd)
>> return container_of(wdd, struct qcom_wdt, wdd);
>> }
>>
>> +static inline int qcom_wdt_enable(struct qcom_wdt *wdt)
>> +{
>> + if (wdt->irq < 0)
>> + return 1;
>> +
>> + /* enable timeout with interrupt */
>> + return 3;
>> +}
>> +
>> +static irqreturn_t qcom_wdt_irq(int irq, void *cookie)
>> +{
>> + struct qcom_wdt *wdt = (struct qcom_wdt *) cookie;
>> +
>> + dev_warn(wdt->dev, "barking, one second countdown to reset\n");
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> static int qcom_wdt_start(struct watchdog_device *wdd)
>> {
>> struct qcom_wdt *wdt = to_qcom_wdt(wdd);
>> + unsigned int bark, bite;
>> +
>> + bark = wdd->timeout;
>> + bite = wdt->irq < 0 ? bark : bark + 1;
>>
>> writel(0, wdt_addr(wdt, WDT_EN));
>> writel(1, wdt_addr(wdt, WDT_RST));
>> - writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
>> - writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
>> - writel(1, wdt_addr(wdt, WDT_EN));
>> + writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
>> + writel(bite * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
>> + writel(qcom_wdt_enable(wdt), wdt_addr(wdt, WDT_EN));
>> return 0;
>> }
>>
>> @@ -210,10 +235,21 @@ static int qcom_wdt_probe(struct platform_device *pdev)
>> wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
>> wdt->wdd.parent = dev;
>> wdt->layout = regs;
>> + wdt->dev = &pdev->dev;
>>
>> if (readl(wdt_addr(wdt, WDT_STS)) & 1)
>> wdt->wdd.bootstatus = WDIOF_CARDRESET;
>>
>> + wdt->irq = platform_get_irq(pdev, 0);
>> + if (wdt->irq >= 0) {
>> + ret = devm_request_irq(&pdev->dev, wdt->irq, qcom_wdt_irq,
>> + IRQF_TRIGGER_RISING, "wdog_bark", wdt);
>> + if (ret) {
>> + dev_err(&pdev->dev, "failed to request irq\n");
>> + return ret;
>> + }
>> + }
>> +
>> /*
>> * If 'timeout-sec' unspecified in devicetree, assume a 30 second
>> * default, unless the max timeout is less than 30 seconds, then use
>> --
>> 2.23.0
>>
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-09-05 16:48 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-09-05 16:21 [PATCH] watchdog: qcom: add support for the bark interrupt Jorge Ramirez-Ortiz
2019-09-05 16:39 ` Bjorn Andersson
2019-09-05 16:48 ` Jorge Ramirez
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).