[PATCHv4 0/4] watchdog: add K3 RTI watchdog support

[PATCHv4 0/4] watchdog: add K3 RTI watchdog support

[Tero Kristo]

Hi,

This addresses the comments from Rob against the DT binding doc, and
does the necessary changes to the driver code based on that (just
compatible name change on that side.) I retained Guenter's reviewed by
tag due to the very minor changes to the code.

Version jumps to v4 for all patches here, I happened to post v3 of patch
#3 before.

-Tero


--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

[PATCHv4 1/4] dt-bindings: watchdog: Add support for TI K3 RTI watchdog

[Tero Kristo]

TI K3 SoCs contain an RTI (Real Time Interrupt) module which can be
used to implement a windowed watchdog functionality. Windowed watchdog
will generate an error if it is petted outside the time window, either
too early or too late.

Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tero Kristo <t-kristo@ti.com>
---
v4:
  * changed license to dual
  * added documentation for missing properties
  * added ref to watchdog.yaml
  * renamed main_rti0 to watchdog0 in example

 .../bindings/watchdog/ti,rti-wdt.yaml         | 65 +++++++++++++++++++
 1 file changed, 65 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml

diff --git a/Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml b/Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml
new file mode 100644
index 000000000000..e83026fef2e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml
@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/watchdog/ti,rti-wdt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments K3 SoC Watchdog Timer
+
+maintainers:
+  - Tero Kristo <t-kristo@ti.com>
+
+description:
+  The TI K3 SoC watchdog timer is implemented via the RTI (Real Time
+  Interrupt) IP module. This timer adds a support for windowed watchdog
+  mode, which will signal an error if it is pinged outside the watchdog
+  time window, meaning either too early or too late. The error signal
+  generated can be routed to either interrupt a safety controller or
+  to directly reset the SoC.
+
+allOf:
+  - $ref: "watchdog.yaml#"
+
+properties:
+  compatible:
+    enum:
+      - ti,j7-rti-wdt
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  assigned-clocks:
+    maxItems: 1
+
+  assigned-clocks-parents:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - power-domains
+
+examples:
+  - |
+    /*
+     * RTI WDT in main domain on J721e SoC. Assigned clocks are used to
+     * select the source clock for the watchdog, forcing it to tick with
+     * a 32kHz clock in this case.
+     */
+    #include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+    watchdog0: rti@2200000 {
+        compatible = "ti,rti-wdt";
+        reg = <0x0 0x2200000 0x0 0x100>;
+        clocks = <&k3_clks 252 1>;
+        power-domains = <&k3_pds 252 TI_SCI_PD_EXCLUSIVE>;
+        assigned-clocks = <&k3_clks 252 1>;
+        assigned-clock-parents = <&k3_clks 252 5>;
+    };
-- 
2.17.1

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

Re: [PATCHv4 1/4] dt-bindings: watchdog: Add support for TI K3 RTI watchdog

[Rob Herring]

On Thu, 12 Mar 2020 11:58:05 +0200, Tero Kristo wrote:
> TI K3 SoCs contain an RTI (Real Time Interrupt) module which can be
> used to implement a windowed watchdog functionality. Windowed watchdog
> will generate an error if it is petted outside the time window, either
> too early or too late.
> 
> Cc: Rob Herring <robh@kernel.org>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Tero Kristo <t-kristo@ti.com>
> ---
> v4:
>   * changed license to dual
>   * added documentation for missing properties
>   * added ref to watchdog.yaml
>   * renamed main_rti0 to watchdog0 in example
> 
>  .../bindings/watchdog/ti,rti-wdt.yaml         | 65 +++++++++++++++++++
>  1 file changed, 65 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCHv4 1/4] dt-bindings: watchdog: Add support for TI K3 RTI watchdog

[Jan Kiszka]

On 12.03.20 10:58, Tero Kristo wrote:
> TI K3 SoCs contain an RTI (Real Time Interrupt) module which can be
> used to implement a windowed watchdog functionality. Windowed watchdog
> will generate an error if it is petted outside the time window, either
> too early or too late.
> 
> Cc: Rob Herring <robh@kernel.org>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Tero Kristo <t-kristo@ti.com>
> ---
> v4:
>   * changed license to dual
>   * added documentation for missing properties
>   * added ref to watchdog.yaml
>   * renamed main_rti0 to watchdog0 in example
> 
>  .../bindings/watchdog/ti,rti-wdt.yaml         | 65 +++++++++++++++++++
>  1 file changed, 65 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml
> 
> diff --git a/Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml b/Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml
> new file mode 100644
> index 000000000000..e83026fef2e9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml
> @@ -0,0 +1,65 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/watchdog/ti,rti-wdt.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Texas Instruments K3 SoC Watchdog Timer
> +
> +maintainers:
> +  - Tero Kristo <t-kristo@ti.com>
> +
> +description:
> +  The TI K3 SoC watchdog timer is implemented via the RTI (Real Time
> +  Interrupt) IP module. This timer adds a support for windowed watchdog
> +  mode, which will signal an error if it is pinged outside the watchdog
> +  time window, meaning either too early or too late. The error signal
> +  generated can be routed to either interrupt a safety controller or
> +  to directly reset the SoC.
> +
> +allOf:
> +  - $ref: "watchdog.yaml#"
> +
> +properties:
> +  compatible:
> +    enum:
> +      - ti,j7-rti-wdt
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  power-domains:
> +    maxItems: 1
> +
> +  assigned-clocks:
> +    maxItems: 1
> +
> +  assigned-clocks-parents:
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - power-domains
> +
> +examples:
> +  - |
> +    /*
> +     * RTI WDT in main domain on J721e SoC. Assigned clocks are used to
> +     * select the source clock for the watchdog, forcing it to tick with
> +     * a 32kHz clock in this case.
> +     */
> +    #include <dt-bindings/soc/ti,sci_pm_domain.h>
> +
> +    watchdog0: rti@2200000 {
> +        compatible = "ti,rti-wdt";

At some stage, you changed the compatible string to something
J721e-specific. This one wasn't updated.

> +        reg = <0x0 0x2200000 0x0 0x100>;
> +        clocks = <&k3_clks 252 1>;
> +        power-domains = <&k3_pds 252 TI_SCI_PD_EXCLUSIVE>;
> +        assigned-clocks = <&k3_clks 252 1>;
> +        assigned-clock-parents = <&k3_clks 252 5>;
> +    };
> 

And where is the binding for the AM65x? I know that PG1 has nice
erratum, but I would expect PG2 to be fine and register-wise compatible, no?

Jan

-- 
Siemens AG, Corporate Technology, CT RDA IOT SES-DE
Corporate Competence Center Embedded Linux

Re: [PATCHv4 1/4] dt-bindings: watchdog: Add support for TI K3 RTI watchdog

[Tero Kristo]

On 18/06/2020 19:09, Jan Kiszka wrote:
> On 12.03.20 10:58, Tero Kristo wrote:
>> TI K3 SoCs contain an RTI (Real Time Interrupt) module which can be
>> used to implement a windowed watchdog functionality. Windowed watchdog
>> will generate an error if it is petted outside the time window, either
>> too early or too late.
>>
>> Cc: Rob Herring <robh@kernel.org>
>> Cc: devicetree@vger.kernel.org
>> Signed-off-by: Tero Kristo <t-kristo@ti.com>
>> ---
>> v4:
>>    * changed license to dual
>>    * added documentation for missing properties
>>    * added ref to watchdog.yaml
>>    * renamed main_rti0 to watchdog0 in example
>>
>>   .../bindings/watchdog/ti,rti-wdt.yaml         | 65 +++++++++++++++++++
>>   1 file changed, 65 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml b/Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml
>> new file mode 100644
>> index 000000000000..e83026fef2e9
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/watchdog/ti,rti-wdt.yaml
>> @@ -0,0 +1,65 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/watchdog/ti,rti-wdt.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Texas Instruments K3 SoC Watchdog Timer
>> +
>> +maintainers:
>> +  - Tero Kristo <t-kristo@ti.com>
>> +
>> +description:
>> +  The TI K3 SoC watchdog timer is implemented via the RTI (Real Time
>> +  Interrupt) IP module. This timer adds a support for windowed watchdog
>> +  mode, which will signal an error if it is pinged outside the watchdog
>> +  time window, meaning either too early or too late. The error signal
>> +  generated can be routed to either interrupt a safety controller or
>> +  to directly reset the SoC.
>> +
>> +allOf:
>> +  - $ref: "watchdog.yaml#"
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ti,j7-rti-wdt
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  power-domains:
>> +    maxItems: 1
>> +
>> +  assigned-clocks:
>> +    maxItems: 1
>> +
>> +  assigned-clocks-parents:
>> +    maxItems: 1
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - clocks
>> +  - power-domains
>> +
>> +examples:
>> +  - |
>> +    /*
>> +     * RTI WDT in main domain on J721e SoC. Assigned clocks are used to
>> +     * select the source clock for the watchdog, forcing it to tick with
>> +     * a 32kHz clock in this case.
>> +     */
>> +    #include <dt-bindings/soc/ti,sci_pm_domain.h>
>> +
>> +    watchdog0: rti@2200000 {
>> +        compatible = "ti,rti-wdt";
> 
> At some stage, you changed the compatible string to something
> J721e-specific. This one wasn't updated.

Hmm nice catch, this should be fixed. I wonder why the DT test tools did 
not catch this when I changed the compatible...

>> +        reg = <0x0 0x2200000 0x0 0x100>;
>> +        clocks = <&k3_clks 252 1>;
>> +        power-domains = <&k3_pds 252 TI_SCI_PD_EXCLUSIVE>;
>> +        assigned-clocks = <&k3_clks 252 1>;
>> +        assigned-clock-parents = <&k3_clks 252 5>;
>> +    };
>>
> 
> And where is the binding for the AM65x? I know that PG1 has nice
> erratum, but I would expect PG2 to be fine and register-wise compatible, no?

ti,am65-rti-wdt should be added as a new compatible to this binding once 
we have a board where we can actually support this. Right now TI AM65x 
boards depend on firmware for the ESM side support; there has been some 
internal discussion about how to get this done and I believe you are 
aware of that.

-Tero
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

[PATCHv4 2/4] watchdog: reset last_hw_keepalive time at start

[Tero Kristo]

Currently the watchdog core does not initialize the last_hw_keepalive
time during watchdog startup. This will cause the watchdog to be pinged
immediately if enough time has passed from the system boot-up time, and
some types of watchdogs like K3 RTI does not like this.

To avoid the issue, setup the last_hw_keepalive time during watchdog
startup.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
---
v4:
  * applied Guenter's reviewed by tag
v2:
  * apply functionality always instead of being behind a flag

 drivers/watchdog/watchdog_dev.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/watchdog/watchdog_dev.c b/drivers/watchdog/watchdog_dev.c
index 8b5c742f24e8..7e4cd34a8c20 100644
--- a/drivers/watchdog/watchdog_dev.c
+++ b/drivers/watchdog/watchdog_dev.c
@@ -282,6 +282,7 @@ static int watchdog_start(struct watchdog_device *wdd)
 	if (err == 0) {
 		set_bit(WDOG_ACTIVE, &wdd->status);
 		wd_data->last_keepalive = started_at;
+		wd_data->last_hw_keepalive = started_at;
 		watchdog_update_worker(wdd);
 	}
 
-- 
2.17.1

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

[PATCHv4 3/4] watchdog: Add K3 RTI watchdog support

[Tero Kristo]

Texas Instruments K3 SoCs contain an RTI (Real Time Interrupt) module
which can be used as a watchdog. This IP provides a support for
windowed watchdog mode, in which the watchdog must be petted within
a certain time window. If it is petted either too soon, or too late,
a watchdog error will be triggered.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
---
v4:
  * applied Guenter's reviewed by tag
  * renamed ti,rti-wdt compatible to ti,j7-rti-wdt

v3:
  * changed to use clk_get/put instead of devm_* versions of this

v2:
  * Added better documentation within the driver code
  * Dropped fck handle, instead get the fck rate during probe only
  * Modified the max_hw_heartbeat calculation logic a bit

 drivers/watchdog/Kconfig   |   8 ++
 drivers/watchdog/Makefile  |   1 +
 drivers/watchdog/rti_wdt.c | 255 +++++++++++++++++++++++++++++++++++++
 3 files changed, 264 insertions(+)
 create mode 100644 drivers/watchdog/rti_wdt.c

diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index cec868f8db3f..81faf47d44a6 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -583,6 +583,14 @@ config DAVINCI_WATCHDOG
 	  NOTE: once enabled, this timer cannot be disabled.
 	  Say N if you are unsure.
 
+config K3_RTI_WATCHDOG
+	tristate "Texas Instruments K3 RTI watchdog"
+	depends on ARCH_K3 || COMPILE_TEST
+	select WATCHDOG_CORE
+	help
+	  Say Y here if you want to include support for the K3 watchdog
+	  timer (RTI module) available in the K3 generation of processors.
+
 config ORION_WATCHDOG
 	tristate "Orion watchdog"
 	depends on ARCH_ORION5X || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU || (COMPILE_TEST && !ARCH_EBSA110)
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 2ee352bf3372..6de2e4ceef19 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_EP93XX_WATCHDOG) += ep93xx_wdt.o
 obj-$(CONFIG_PNX4008_WATCHDOG) += pnx4008_wdt.o
 obj-$(CONFIG_IOP_WATCHDOG) += iop_wdt.o
 obj-$(CONFIG_DAVINCI_WATCHDOG) += davinci_wdt.o
+obj-$(CONFIG_K3_RTI_WATCHDOG) += rti_wdt.o
 obj-$(CONFIG_ORION_WATCHDOG) += orion_wdt.o
 obj-$(CONFIG_SUNXI_WATCHDOG) += sunxi_wdt.o
 obj-$(CONFIG_RN5T618_WATCHDOG) += rn5t618_wdt.o
diff --git a/drivers/watchdog/rti_wdt.c b/drivers/watchdog/rti_wdt.c
new file mode 100644
index 000000000000..d456dd72d99a
--- /dev/null
+++ b/drivers/watchdog/rti_wdt.c
@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Watchdog driver for the K3 RTI module
+ *
+ * (c) Copyright 2019-2020 Texas Instruments Inc.
+ * All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/types.h>
+#include <linux/watchdog.h>
+
+#define DEFAULT_HEARTBEAT 60
+
+/* Max heartbeat is calculated at 32kHz source clock */
+#define MAX_HEARTBEAT	1000
+
+/* Timer register set definition */
+#define RTIDWDCTRL	0x90
+#define RTIDWDPRLD	0x94
+#define RTIWDSTATUS	0x98
+#define RTIWDKEY	0x9c
+#define RTIDWDCNTR	0xa0
+#define RTIWWDRXCTRL	0xa4
+#define RTIWWDSIZECTRL	0xa8
+
+#define RTIWWDRX_NMI	0xa
+
+#define RTIWWDSIZE_50P	0x50
+
+#define WDENABLE_KEY	0xa98559da
+
+#define WDKEY_SEQ0		0xe51a
+#define WDKEY_SEQ1		0xa35c
+
+#define WDT_PRELOAD_SHIFT	13
+
+#define WDT_PRELOAD_MAX		0xfff
+
+#define DWDST			BIT(1)
+
+static int heartbeat;
+
+/*
+ * struct to hold data for each WDT device
+ * @base - base io address of WD device
+ * @freq - source clock frequency of WDT
+ * @wdd  - hold watchdog device as is in WDT core
+ */
+struct rti_wdt_device {
+	void __iomem		*base;
+	unsigned long		freq;
+	struct watchdog_device	wdd;
+};
+
+static int rti_wdt_start(struct watchdog_device *wdd)
+{
+	u32 timer_margin;
+	struct rti_wdt_device *wdt = watchdog_get_drvdata(wdd);
+
+	/* set timeout period */
+	timer_margin = (u64)wdd->timeout * wdt->freq;
+	timer_margin >>= WDT_PRELOAD_SHIFT;
+	if (timer_margin > WDT_PRELOAD_MAX)
+		timer_margin = WDT_PRELOAD_MAX;
+	writel_relaxed(timer_margin, wdt->base + RTIDWDPRLD);
+
+	/*
+	 * RTI only supports a windowed mode, where the watchdog can only
+	 * be petted during the open window; not too early or not too late.
+	 * The HW configuration options only allow for the open window size
+	 * to be 50% or less than that; we obviouly want to configure the open
+	 * window as large as possible so we select the 50% option. To avoid
+	 * any glitches, we accommodate 5% safety margin also, so we setup
+	 * the min_hw_hearbeat at 55% of the timeout period.
+	 */
+	wdd->min_hw_heartbeat_ms = 11 * wdd->timeout * 1000 / 20;
+
+	/* Generate NMI when wdt expires */
+	writel_relaxed(RTIWWDRX_NMI, wdt->base + RTIWWDRXCTRL);
+
+	/* Open window size 50%; this is the largest window size available */
+	writel_relaxed(RTIWWDSIZE_50P, wdt->base + RTIWWDSIZECTRL);
+
+	readl_relaxed(wdt->base + RTIWWDSIZECTRL);
+
+	/* enable watchdog */
+	writel_relaxed(WDENABLE_KEY, wdt->base + RTIDWDCTRL);
+	return 0;
+}
+
+static int rti_wdt_ping(struct watchdog_device *wdd)
+{
+	struct rti_wdt_device *wdt = watchdog_get_drvdata(wdd);
+
+	/* put watchdog in service state */
+	writel_relaxed(WDKEY_SEQ0, wdt->base + RTIWDKEY);
+	/* put watchdog in active state */
+	writel_relaxed(WDKEY_SEQ1, wdt->base + RTIWDKEY);
+
+	return 0;
+}
+
+static unsigned int rti_wdt_get_timeleft(struct watchdog_device *wdd)
+{
+	u64 timer_counter;
+	u32 val;
+	struct rti_wdt_device *wdt = watchdog_get_drvdata(wdd);
+
+	/* if timeout has occurred then return 0 */
+	val = readl_relaxed(wdt->base + RTIWDSTATUS);
+	if (val & DWDST)
+		return 0;
+
+	timer_counter = readl_relaxed(wdt->base + RTIDWDCNTR);
+
+	do_div(timer_counter, wdt->freq);
+
+	return timer_counter;
+}
+
+static const struct watchdog_info rti_wdt_info = {
+	.options = WDIOF_KEEPALIVEPING,
+	.identity = "K3 RTI Watchdog",
+};
+
+static const struct watchdog_ops rti_wdt_ops = {
+	.owner		= THIS_MODULE,
+	.start		= rti_wdt_start,
+	.ping		= rti_wdt_ping,
+	.get_timeleft	= rti_wdt_get_timeleft,
+};
+
+static int rti_wdt_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct device *dev = &pdev->dev;
+	struct resource *wdt_mem;
+	struct watchdog_device *wdd;
+	struct rti_wdt_device *wdt;
+	struct clk *clk;
+
+	wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
+	if (!wdt)
+		return -ENOMEM;
+
+	clk = clk_get(dev, NULL);
+	if (IS_ERR(clk)) {
+		if (PTR_ERR(clk) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get clock\n");
+		return PTR_ERR(clk);
+	}
+
+	wdt->freq = clk_get_rate(clk);
+
+	clk_put(clk);
+
+	if (!wdt->freq) {
+		dev_err(dev, "Failed to get fck rate.\n");
+		return -EINVAL;
+	}
+
+	pm_runtime_enable(dev);
+	ret = pm_runtime_get_sync(dev);
+	if (ret) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(&pdev->dev, "runtime pm failed\n");
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, wdt);
+
+	wdd = &wdt->wdd;
+	wdd->info = &rti_wdt_info;
+	wdd->ops = &rti_wdt_ops;
+	wdd->min_timeout = 1;
+	wdd->max_hw_heartbeat_ms = (WDT_PRELOAD_MAX << WDT_PRELOAD_SHIFT) /
+		wdt->freq * 1000;
+	wdd->timeout = DEFAULT_HEARTBEAT;
+	wdd->parent = dev;
+
+	watchdog_init_timeout(wdd, heartbeat, dev);
+
+	watchdog_set_drvdata(wdd, wdt);
+	watchdog_set_nowayout(wdd, 1);
+	watchdog_set_restart_priority(wdd, 128);
+
+	wdt_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	wdt->base = devm_ioremap_resource(dev, wdt_mem);
+	if (IS_ERR(wdt->base)) {
+		ret = PTR_ERR(wdt->base);
+		goto err_iomap;
+	}
+
+	ret = watchdog_register_device(wdd);
+	if (ret) {
+		dev_err(dev, "cannot register watchdog device\n");
+		goto err_iomap;
+	}
+
+	return 0;
+
+err_iomap:
+	pm_runtime_put_sync(&pdev->dev);
+
+	return ret;
+}
+
+static int rti_wdt_remove(struct platform_device *pdev)
+{
+	struct rti_wdt_device *wdt = platform_get_drvdata(pdev);
+
+	watchdog_unregister_device(&wdt->wdd);
+	pm_runtime_put(&pdev->dev);
+
+	return 0;
+}
+
+static const struct of_device_id rti_wdt_of_match[] = {
+	{ .compatible = "ti,j7-rti-wdt", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, rti_wdt_of_match);
+
+static struct platform_driver rti_wdt_driver = {
+	.driver = {
+		.name = "rti-wdt",
+		.of_match_table = rti_wdt_of_match,
+	},
+	.probe = rti_wdt_probe,
+	.remove = rti_wdt_remove,
+};
+
+module_platform_driver(rti_wdt_driver);
+
+MODULE_AUTHOR("Tero Kristo <t-kristo@ti.com>");
+MODULE_DESCRIPTION("K3 RTI Watchdog Driver");
+
+module_param(heartbeat, int, 0);
+MODULE_PARM_DESC(heartbeat,
+		 "Watchdog heartbeat period in seconds from 1 to "
+		 __MODULE_STRING(MAX_HEARTBEAT) ", default "
+		 __MODULE_STRING(DEFAULT_HEARTBEAT));
+
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:rti-wdt");
-- 
2.17.1

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

[PATCHv4 4/4] arm64: dts: ti: k3-j721e-main: Add MAIN domain watchdog entries

[Tero Kristo]

Add DT entries for main domain watchdog0 and 1 instances.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
---
v4:
  * renamed main_rti* instances to watchdog*

 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 0b9d14b838a1..aa525bc321f1 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -963,4 +963,22 @@
 
 		status = "disabled";
 	};
+
+	watchdog0: watchdog@2200000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x0 0x2200000 0x0 0x100>;
+		clocks = <&k3_clks 252 1>;
+		power-domains = <&k3_pds 252 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 252 1>;
+		assigned-clock-parents = <&k3_clks 252 5>;
+	};
+
+	watchdog1: watchdog@2210000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x0 0x2210000 0x0 0x100>;
+		clocks = <&k3_clks 253 1>;
+		power-domains = <&k3_pds 253 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 253 1>;
+		assigned-clock-parents = <&k3_clks 253 5>;
+	};
 };
-- 
2.17.1

--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki