linux-watchdog.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH] watchdog: Remove MV64x60 watchdog driver
@ 2021-03-18 17:25 Christophe Leroy
  2021-03-18 18:32 ` Guenter Roeck
  0 siblings, 1 reply; 7+ messages in thread
From: Christophe Leroy @ 2021-03-18 17:25 UTC (permalink / raw)
  To: Wim Van Sebroeck, Guenter Roeck, Sebastian Hesselbarth
  Cc: linux-kernel, linuxppc-dev, linux-watchdog, netdev

Commit 92c8c16f3457 ("powerpc/embedded6xx: Remove C2K board support")
removed the last selector of CONFIG_MV64X60.

Therefore CONFIG_MV64X60_WDT cannot be selected anymore and
can be removed.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
---
 drivers/watchdog/Kconfig       |   4 -
 drivers/watchdog/Makefile      |   1 -
 drivers/watchdog/mv64x60_wdt.c | 324 ---------------------------------
 include/linux/mv643xx.h        |   8 -
 4 files changed, 337 deletions(-)
 delete mode 100644 drivers/watchdog/mv64x60_wdt.c

diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 1fe0042a48d2..178296bda151 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -1831,10 +1831,6 @@ config 8xxx_WDT
 
 	  For BookE processors (MPC85xx) use the BOOKE_WDT driver instead.
 
-config MV64X60_WDT
-	tristate "MV64X60 (Marvell Discovery) Watchdog Timer"
-	depends on MV64X60 || COMPILE_TEST
-
 config PIKA_WDT
 	tristate "PIKA FPGA Watchdog"
 	depends on WARP || (PPC64 && COMPILE_TEST)
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index f3a6540e725e..752c6513f731 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -175,7 +175,6 @@ obj-$(CONFIG_PIC32_DMT) += pic32-dmt.o
 # POWERPC Architecture
 obj-$(CONFIG_GEF_WDT) += gef_wdt.o
 obj-$(CONFIG_8xxx_WDT) += mpc8xxx_wdt.o
-obj-$(CONFIG_MV64X60_WDT) += mv64x60_wdt.o
 obj-$(CONFIG_PIKA_WDT) += pika_wdt.o
 obj-$(CONFIG_BOOKE_WDT) += booke_wdt.o
 obj-$(CONFIG_MEN_A21_WDT) += mena21_wdt.o
diff --git a/drivers/watchdog/mv64x60_wdt.c b/drivers/watchdog/mv64x60_wdt.c
deleted file mode 100644
index 894aa63488d3..000000000000
--- a/drivers/watchdog/mv64x60_wdt.c
+++ /dev/null
@@ -1,324 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * mv64x60_wdt.c - MV64X60 (Marvell Discovery) watchdog userspace interface
- *
- * Author: James Chapman <jchapman@katalix.com>
- *
- * Platform-specific setup code should configure the dog to generate
- * interrupt or reset as required.  This code only enables/disables
- * and services the watchdog.
- *
- * Derived from mpc8xx_wdt.c, with the following copyright.
- *
- * 2002 (c) Florian Schirmer <jolt@tuxbox.org>
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/fs.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/miscdevice.h>
-#include <linux/module.h>
-#include <linux/watchdog.h>
-#include <linux/platform_device.h>
-#include <linux/mv643xx.h>
-#include <linux/uaccess.h>
-#include <linux/io.h>
-
-#define MV64x60_WDT_WDC_OFFSET	0
-
-/*
- * The watchdog configuration register contains a pair of 2-bit fields,
- *   1.  a reload field, bits 27-26, which triggers a reload of
- *       the countdown register, and
- *   2.  an enable field, bits 25-24, which toggles between
- *       enabling and disabling the watchdog timer.
- * Bit 31 is a read-only field which indicates whether the
- * watchdog timer is currently enabled.
- *
- * The low 24 bits contain the timer reload value.
- */
-#define MV64x60_WDC_ENABLE_SHIFT	24
-#define MV64x60_WDC_SERVICE_SHIFT	26
-#define MV64x60_WDC_ENABLED_SHIFT	31
-
-#define MV64x60_WDC_ENABLED_TRUE	1
-#define MV64x60_WDC_ENABLED_FALSE	0
-
-/* Flags bits */
-#define MV64x60_WDOG_FLAG_OPENED	0
-
-static unsigned long wdt_flags;
-static int wdt_status;
-static void __iomem *mv64x60_wdt_regs;
-static int mv64x60_wdt_timeout;
-static int mv64x60_wdt_count;
-static unsigned int bus_clk;
-static char expect_close;
-static DEFINE_SPINLOCK(mv64x60_wdt_spinlock);
-
-static bool nowayout = WATCHDOG_NOWAYOUT;
-module_param(nowayout, bool, 0);
-MODULE_PARM_DESC(nowayout,
-		"Watchdog cannot be stopped once started (default="
-				__MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
-
-static int mv64x60_wdt_toggle_wdc(int enabled_predicate, int field_shift)
-{
-	u32 data;
-	u32 enabled;
-	int ret = 0;
-
-	spin_lock(&mv64x60_wdt_spinlock);
-	data = readl(mv64x60_wdt_regs + MV64x60_WDT_WDC_OFFSET);
-	enabled = (data >> MV64x60_WDC_ENABLED_SHIFT) & 1;
-
-	/* only toggle the requested field if enabled state matches predicate */
-	if ((enabled ^ enabled_predicate) == 0) {
-		/* We write a 1, then a 2 -- to the appropriate field */
-		data = (1 << field_shift) | mv64x60_wdt_count;
-		writel(data, mv64x60_wdt_regs + MV64x60_WDT_WDC_OFFSET);
-
-		data = (2 << field_shift) | mv64x60_wdt_count;
-		writel(data, mv64x60_wdt_regs + MV64x60_WDT_WDC_OFFSET);
-		ret = 1;
-	}
-	spin_unlock(&mv64x60_wdt_spinlock);
-
-	return ret;
-}
-
-static void mv64x60_wdt_service(void)
-{
-	mv64x60_wdt_toggle_wdc(MV64x60_WDC_ENABLED_TRUE,
-			       MV64x60_WDC_SERVICE_SHIFT);
-}
-
-static void mv64x60_wdt_handler_enable(void)
-{
-	if (mv64x60_wdt_toggle_wdc(MV64x60_WDC_ENABLED_FALSE,
-				   MV64x60_WDC_ENABLE_SHIFT)) {
-		mv64x60_wdt_service();
-		pr_notice("watchdog activated\n");
-	}
-}
-
-static void mv64x60_wdt_handler_disable(void)
-{
-	if (mv64x60_wdt_toggle_wdc(MV64x60_WDC_ENABLED_TRUE,
-				   MV64x60_WDC_ENABLE_SHIFT))
-		pr_notice("watchdog deactivated\n");
-}
-
-static void mv64x60_wdt_set_timeout(unsigned int timeout)
-{
-	/* maximum bus cycle count is 0xFFFFFFFF */
-	if (timeout > 0xFFFFFFFF / bus_clk)
-		timeout = 0xFFFFFFFF / bus_clk;
-
-	mv64x60_wdt_count = timeout * bus_clk >> 8;
-	mv64x60_wdt_timeout = timeout;
-}
-
-static int mv64x60_wdt_open(struct inode *inode, struct file *file)
-{
-	if (test_and_set_bit(MV64x60_WDOG_FLAG_OPENED, &wdt_flags))
-		return -EBUSY;
-
-	if (nowayout)
-		__module_get(THIS_MODULE);
-
-	mv64x60_wdt_handler_enable();
-
-	return stream_open(inode, file);
-}
-
-static int mv64x60_wdt_release(struct inode *inode, struct file *file)
-{
-	if (expect_close == 42)
-		mv64x60_wdt_handler_disable();
-	else {
-		pr_crit("unexpected close, not stopping timer!\n");
-		mv64x60_wdt_service();
-	}
-	expect_close = 0;
-
-	clear_bit(MV64x60_WDOG_FLAG_OPENED, &wdt_flags);
-
-	return 0;
-}
-
-static ssize_t mv64x60_wdt_write(struct file *file, const char __user *data,
-				 size_t len, loff_t *ppos)
-{
-	if (len) {
-		if (!nowayout) {
-			size_t i;
-
-			expect_close = 0;
-
-			for (i = 0; i != len; i++) {
-				char c;
-				if (get_user(c, data + i))
-					return -EFAULT;
-				if (c == 'V')
-					expect_close = 42;
-			}
-		}
-		mv64x60_wdt_service();
-	}
-
-	return len;
-}
-
-static long mv64x60_wdt_ioctl(struct file *file,
-					unsigned int cmd, unsigned long arg)
-{
-	int timeout;
-	int options;
-	void __user *argp = (void __user *)arg;
-	static const struct watchdog_info info = {
-		.options =	WDIOF_SETTIMEOUT	|
-				WDIOF_MAGICCLOSE	|
-				WDIOF_KEEPALIVEPING,
-		.firmware_version = 0,
-		.identity = "MV64x60 watchdog",
-	};
-
-	switch (cmd) {
-	case WDIOC_GETSUPPORT:
-		if (copy_to_user(argp, &info, sizeof(info)))
-			return -EFAULT;
-		break;
-
-	case WDIOC_GETSTATUS:
-	case WDIOC_GETBOOTSTATUS:
-		if (put_user(wdt_status, (int __user *)argp))
-			return -EFAULT;
-		wdt_status &= ~WDIOF_KEEPALIVEPING;
-		break;
-
-	case WDIOC_GETTEMP:
-		return -EOPNOTSUPP;
-
-	case WDIOC_SETOPTIONS:
-		if (get_user(options, (int __user *)argp))
-			return -EFAULT;
-
-		if (options & WDIOS_DISABLECARD)
-			mv64x60_wdt_handler_disable();
-
-		if (options & WDIOS_ENABLECARD)
-			mv64x60_wdt_handler_enable();
-		break;
-
-	case WDIOC_KEEPALIVE:
-		mv64x60_wdt_service();
-		wdt_status |= WDIOF_KEEPALIVEPING;
-		break;
-
-	case WDIOC_SETTIMEOUT:
-		if (get_user(timeout, (int __user *)argp))
-			return -EFAULT;
-		mv64x60_wdt_set_timeout(timeout);
-		fallthrough;
-
-	case WDIOC_GETTIMEOUT:
-		if (put_user(mv64x60_wdt_timeout, (int __user *)argp))
-			return -EFAULT;
-		break;
-
-	default:
-		return -ENOTTY;
-	}
-
-	return 0;
-}
-
-static const struct file_operations mv64x60_wdt_fops = {
-	.owner = THIS_MODULE,
-	.llseek = no_llseek,
-	.write = mv64x60_wdt_write,
-	.unlocked_ioctl = mv64x60_wdt_ioctl,
-	.compat_ioctl = compat_ptr_ioctl,
-	.open = mv64x60_wdt_open,
-	.release = mv64x60_wdt_release,
-};
-
-static struct miscdevice mv64x60_wdt_miscdev = {
-	.minor = WATCHDOG_MINOR,
-	.name = "watchdog",
-	.fops = &mv64x60_wdt_fops,
-};
-
-static int mv64x60_wdt_probe(struct platform_device *dev)
-{
-	struct mv64x60_wdt_pdata *pdata = dev_get_platdata(&dev->dev);
-	struct resource *r;
-	int timeout = 10;
-
-	bus_clk = 133;			/* in MHz */
-	if (pdata) {
-		timeout = pdata->timeout;
-		bus_clk = pdata->bus_clk;
-	}
-
-	/* Since bus_clk is truncated MHz, actual frequency could be
-	 * up to 1MHz higher.  Round up, since it's better to time out
-	 * too late than too soon.
-	 */
-	bus_clk++;
-	bus_clk *= 1000000;		/* convert to Hz */
-
-	r = platform_get_resource(dev, IORESOURCE_MEM, 0);
-	if (!r)
-		return -ENODEV;
-
-	mv64x60_wdt_regs = devm_ioremap(&dev->dev, r->start, resource_size(r));
-	if (mv64x60_wdt_regs == NULL)
-		return -ENOMEM;
-
-	mv64x60_wdt_set_timeout(timeout);
-
-	mv64x60_wdt_handler_disable();	/* in case timer was already running */
-
-	return misc_register(&mv64x60_wdt_miscdev);
-}
-
-static int mv64x60_wdt_remove(struct platform_device *dev)
-{
-	misc_deregister(&mv64x60_wdt_miscdev);
-
-	mv64x60_wdt_handler_disable();
-
-	return 0;
-}
-
-static struct platform_driver mv64x60_wdt_driver = {
-	.probe = mv64x60_wdt_probe,
-	.remove = mv64x60_wdt_remove,
-	.driver = {
-		.name = MV64x60_WDT_NAME,
-	},
-};
-
-static int __init mv64x60_wdt_init(void)
-{
-	pr_info("MV64x60 watchdog driver\n");
-
-	return platform_driver_register(&mv64x60_wdt_driver);
-}
-
-static void __exit mv64x60_wdt_exit(void)
-{
-	platform_driver_unregister(&mv64x60_wdt_driver);
-}
-
-module_init(mv64x60_wdt_init);
-module_exit(mv64x60_wdt_exit);
-
-MODULE_AUTHOR("James Chapman <jchapman@katalix.com>");
-MODULE_DESCRIPTION("MV64x60 watchdog driver");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:" MV64x60_WDT_NAME);
diff --git a/include/linux/mv643xx.h b/include/linux/mv643xx.h
index 47e5679b48e1..000b126acfb6 100644
--- a/include/linux/mv643xx.h
+++ b/include/linux/mv643xx.h
@@ -918,12 +918,4 @@
 
 extern void mv64340_irq_init(unsigned int base);
 
-/* Watchdog Platform Device, Driver Data */
-#define	MV64x60_WDT_NAME			"mv64x60_wdt"
-
-struct mv64x60_wdt_pdata {
-	int	timeout;	/* watchdog expiry in seconds, default 10 */
-	int	bus_clk;	/* bus clock in MHz, default 133 */
-};
-
 #endif /* __ASM_MV643XX_H */
-- 
2.25.0


^ permalink raw reply related	[flat|nested] 7+ messages in thread

* Re: [PATCH] watchdog: Remove MV64x60 watchdog driver
  2021-03-18 17:25 [PATCH] watchdog: Remove MV64x60 watchdog driver Christophe Leroy
@ 2021-03-18 18:32 ` Guenter Roeck
  2021-05-17 11:17   ` Michael Ellerman
  0 siblings, 1 reply; 7+ messages in thread
From: Guenter Roeck @ 2021-03-18 18:32 UTC (permalink / raw)
  To: Christophe Leroy, Wim Van Sebroeck, Sebastian Hesselbarth
  Cc: linux-kernel, linuxppc-dev, linux-watchdog, netdev

On 3/18/21 10:25 AM, Christophe Leroy wrote:
> Commit 92c8c16f3457 ("powerpc/embedded6xx: Remove C2K board support")
> removed the last selector of CONFIG_MV64X60.
> 
> Therefore CONFIG_MV64X60_WDT cannot be selected anymore and
> can be removed.
> 
> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>

Reviewed-by: Guenter Roeck <linux@roeck-us.net>

> ---
>  drivers/watchdog/Kconfig       |   4 -
>  drivers/watchdog/Makefile      |   1 -
>  drivers/watchdog/mv64x60_wdt.c | 324 ---------------------------------
>  include/linux/mv643xx.h        |   8 -
>  4 files changed, 337 deletions(-)
>  delete mode 100644 drivers/watchdog/mv64x60_wdt.c
> 
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index 1fe0042a48d2..178296bda151 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -1831,10 +1831,6 @@ config 8xxx_WDT
>  
>  	  For BookE processors (MPC85xx) use the BOOKE_WDT driver instead.
>  
> -config MV64X60_WDT
> -	tristate "MV64X60 (Marvell Discovery) Watchdog Timer"
> -	depends on MV64X60 || COMPILE_TEST
> -
>  config PIKA_WDT
>  	tristate "PIKA FPGA Watchdog"
>  	depends on WARP || (PPC64 && COMPILE_TEST)
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index f3a6540e725e..752c6513f731 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -175,7 +175,6 @@ obj-$(CONFIG_PIC32_DMT) += pic32-dmt.o
>  # POWERPC Architecture
>  obj-$(CONFIG_GEF_WDT) += gef_wdt.o
>  obj-$(CONFIG_8xxx_WDT) += mpc8xxx_wdt.o
> -obj-$(CONFIG_MV64X60_WDT) += mv64x60_wdt.o
>  obj-$(CONFIG_PIKA_WDT) += pika_wdt.o
>  obj-$(CONFIG_BOOKE_WDT) += booke_wdt.o
>  obj-$(CONFIG_MEN_A21_WDT) += mena21_wdt.o
> diff --git a/drivers/watchdog/mv64x60_wdt.c b/drivers/watchdog/mv64x60_wdt.c
> deleted file mode 100644
> index 894aa63488d3..000000000000
> --- a/drivers/watchdog/mv64x60_wdt.c
> +++ /dev/null
> @@ -1,324 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * mv64x60_wdt.c - MV64X60 (Marvell Discovery) watchdog userspace interface
> - *
> - * Author: James Chapman <jchapman@katalix.com>
> - *
> - * Platform-specific setup code should configure the dog to generate
> - * interrupt or reset as required.  This code only enables/disables
> - * and services the watchdog.
> - *
> - * Derived from mpc8xx_wdt.c, with the following copyright.
> - *
> - * 2002 (c) Florian Schirmer <jolt@tuxbox.org>
> - */
> -
> -#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> -
> -#include <linux/fs.h>
> -#include <linux/init.h>
> -#include <linux/kernel.h>
> -#include <linux/miscdevice.h>
> -#include <linux/module.h>
> -#include <linux/watchdog.h>
> -#include <linux/platform_device.h>
> -#include <linux/mv643xx.h>
> -#include <linux/uaccess.h>
> -#include <linux/io.h>
> -
> -#define MV64x60_WDT_WDC_OFFSET	0
> -
> -/*
> - * The watchdog configuration register contains a pair of 2-bit fields,
> - *   1.  a reload field, bits 27-26, which triggers a reload of
> - *       the countdown register, and
> - *   2.  an enable field, bits 25-24, which toggles between
> - *       enabling and disabling the watchdog timer.
> - * Bit 31 is a read-only field which indicates whether the
> - * watchdog timer is currently enabled.
> - *
> - * The low 24 bits contain the timer reload value.
> - */
> -#define MV64x60_WDC_ENABLE_SHIFT	24
> -#define MV64x60_WDC_SERVICE_SHIFT	26
> -#define MV64x60_WDC_ENABLED_SHIFT	31
> -
> -#define MV64x60_WDC_ENABLED_TRUE	1
> -#define MV64x60_WDC_ENABLED_FALSE	0
> -
> -/* Flags bits */
> -#define MV64x60_WDOG_FLAG_OPENED	0
> -
> -static unsigned long wdt_flags;
> -static int wdt_status;
> -static void __iomem *mv64x60_wdt_regs;
> -static int mv64x60_wdt_timeout;
> -static int mv64x60_wdt_count;
> -static unsigned int bus_clk;
> -static char expect_close;
> -static DEFINE_SPINLOCK(mv64x60_wdt_spinlock);
> -
> -static bool nowayout = WATCHDOG_NOWAYOUT;
> -module_param(nowayout, bool, 0);
> -MODULE_PARM_DESC(nowayout,
> -		"Watchdog cannot be stopped once started (default="
> -				__MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
> -
> -static int mv64x60_wdt_toggle_wdc(int enabled_predicate, int field_shift)
> -{
> -	u32 data;
> -	u32 enabled;
> -	int ret = 0;
> -
> -	spin_lock(&mv64x60_wdt_spinlock);
> -	data = readl(mv64x60_wdt_regs + MV64x60_WDT_WDC_OFFSET);
> -	enabled = (data >> MV64x60_WDC_ENABLED_SHIFT) & 1;
> -
> -	/* only toggle the requested field if enabled state matches predicate */
> -	if ((enabled ^ enabled_predicate) == 0) {
> -		/* We write a 1, then a 2 -- to the appropriate field */
> -		data = (1 << field_shift) | mv64x60_wdt_count;
> -		writel(data, mv64x60_wdt_regs + MV64x60_WDT_WDC_OFFSET);
> -
> -		data = (2 << field_shift) | mv64x60_wdt_count;
> -		writel(data, mv64x60_wdt_regs + MV64x60_WDT_WDC_OFFSET);
> -		ret = 1;
> -	}
> -	spin_unlock(&mv64x60_wdt_spinlock);
> -
> -	return ret;
> -}
> -
> -static void mv64x60_wdt_service(void)
> -{
> -	mv64x60_wdt_toggle_wdc(MV64x60_WDC_ENABLED_TRUE,
> -			       MV64x60_WDC_SERVICE_SHIFT);
> -}
> -
> -static void mv64x60_wdt_handler_enable(void)
> -{
> -	if (mv64x60_wdt_toggle_wdc(MV64x60_WDC_ENABLED_FALSE,
> -				   MV64x60_WDC_ENABLE_SHIFT)) {
> -		mv64x60_wdt_service();
> -		pr_notice("watchdog activated\n");
> -	}
> -}
> -
> -static void mv64x60_wdt_handler_disable(void)
> -{
> -	if (mv64x60_wdt_toggle_wdc(MV64x60_WDC_ENABLED_TRUE,
> -				   MV64x60_WDC_ENABLE_SHIFT))
> -		pr_notice("watchdog deactivated\n");
> -}
> -
> -static void mv64x60_wdt_set_timeout(unsigned int timeout)
> -{
> -	/* maximum bus cycle count is 0xFFFFFFFF */
> -	if (timeout > 0xFFFFFFFF / bus_clk)
> -		timeout = 0xFFFFFFFF / bus_clk;
> -
> -	mv64x60_wdt_count = timeout * bus_clk >> 8;
> -	mv64x60_wdt_timeout = timeout;
> -}
> -
> -static int mv64x60_wdt_open(struct inode *inode, struct file *file)
> -{
> -	if (test_and_set_bit(MV64x60_WDOG_FLAG_OPENED, &wdt_flags))
> -		return -EBUSY;
> -
> -	if (nowayout)
> -		__module_get(THIS_MODULE);
> -
> -	mv64x60_wdt_handler_enable();
> -
> -	return stream_open(inode, file);
> -}
> -
> -static int mv64x60_wdt_release(struct inode *inode, struct file *file)
> -{
> -	if (expect_close == 42)
> -		mv64x60_wdt_handler_disable();
> -	else {
> -		pr_crit("unexpected close, not stopping timer!\n");
> -		mv64x60_wdt_service();
> -	}
> -	expect_close = 0;
> -
> -	clear_bit(MV64x60_WDOG_FLAG_OPENED, &wdt_flags);
> -
> -	return 0;
> -}
> -
> -static ssize_t mv64x60_wdt_write(struct file *file, const char __user *data,
> -				 size_t len, loff_t *ppos)
> -{
> -	if (len) {
> -		if (!nowayout) {
> -			size_t i;
> -
> -			expect_close = 0;
> -
> -			for (i = 0; i != len; i++) {
> -				char c;
> -				if (get_user(c, data + i))
> -					return -EFAULT;
> -				if (c == 'V')
> -					expect_close = 42;
> -			}
> -		}
> -		mv64x60_wdt_service();
> -	}
> -
> -	return len;
> -}
> -
> -static long mv64x60_wdt_ioctl(struct file *file,
> -					unsigned int cmd, unsigned long arg)
> -{
> -	int timeout;
> -	int options;
> -	void __user *argp = (void __user *)arg;
> -	static const struct watchdog_info info = {
> -		.options =	WDIOF_SETTIMEOUT	|
> -				WDIOF_MAGICCLOSE	|
> -				WDIOF_KEEPALIVEPING,
> -		.firmware_version = 0,
> -		.identity = "MV64x60 watchdog",
> -	};
> -
> -	switch (cmd) {
> -	case WDIOC_GETSUPPORT:
> -		if (copy_to_user(argp, &info, sizeof(info)))
> -			return -EFAULT;
> -		break;
> -
> -	case WDIOC_GETSTATUS:
> -	case WDIOC_GETBOOTSTATUS:
> -		if (put_user(wdt_status, (int __user *)argp))
> -			return -EFAULT;
> -		wdt_status &= ~WDIOF_KEEPALIVEPING;
> -		break;
> -
> -	case WDIOC_GETTEMP:
> -		return -EOPNOTSUPP;
> -
> -	case WDIOC_SETOPTIONS:
> -		if (get_user(options, (int __user *)argp))
> -			return -EFAULT;
> -
> -		if (options & WDIOS_DISABLECARD)
> -			mv64x60_wdt_handler_disable();
> -
> -		if (options & WDIOS_ENABLECARD)
> -			mv64x60_wdt_handler_enable();
> -		break;
> -
> -	case WDIOC_KEEPALIVE:
> -		mv64x60_wdt_service();
> -		wdt_status |= WDIOF_KEEPALIVEPING;
> -		break;
> -
> -	case WDIOC_SETTIMEOUT:
> -		if (get_user(timeout, (int __user *)argp))
> -			return -EFAULT;
> -		mv64x60_wdt_set_timeout(timeout);
> -		fallthrough;
> -
> -	case WDIOC_GETTIMEOUT:
> -		if (put_user(mv64x60_wdt_timeout, (int __user *)argp))
> -			return -EFAULT;
> -		break;
> -
> -	default:
> -		return -ENOTTY;
> -	}
> -
> -	return 0;
> -}
> -
> -static const struct file_operations mv64x60_wdt_fops = {
> -	.owner = THIS_MODULE,
> -	.llseek = no_llseek,
> -	.write = mv64x60_wdt_write,
> -	.unlocked_ioctl = mv64x60_wdt_ioctl,
> -	.compat_ioctl = compat_ptr_ioctl,
> -	.open = mv64x60_wdt_open,
> -	.release = mv64x60_wdt_release,
> -};
> -
> -static struct miscdevice mv64x60_wdt_miscdev = {
> -	.minor = WATCHDOG_MINOR,
> -	.name = "watchdog",
> -	.fops = &mv64x60_wdt_fops,
> -};
> -
> -static int mv64x60_wdt_probe(struct platform_device *dev)
> -{
> -	struct mv64x60_wdt_pdata *pdata = dev_get_platdata(&dev->dev);
> -	struct resource *r;
> -	int timeout = 10;
> -
> -	bus_clk = 133;			/* in MHz */
> -	if (pdata) {
> -		timeout = pdata->timeout;
> -		bus_clk = pdata->bus_clk;
> -	}
> -
> -	/* Since bus_clk is truncated MHz, actual frequency could be
> -	 * up to 1MHz higher.  Round up, since it's better to time out
> -	 * too late than too soon.
> -	 */
> -	bus_clk++;
> -	bus_clk *= 1000000;		/* convert to Hz */
> -
> -	r = platform_get_resource(dev, IORESOURCE_MEM, 0);
> -	if (!r)
> -		return -ENODEV;
> -
> -	mv64x60_wdt_regs = devm_ioremap(&dev->dev, r->start, resource_size(r));
> -	if (mv64x60_wdt_regs == NULL)
> -		return -ENOMEM;
> -
> -	mv64x60_wdt_set_timeout(timeout);
> -
> -	mv64x60_wdt_handler_disable();	/* in case timer was already running */
> -
> -	return misc_register(&mv64x60_wdt_miscdev);
> -}
> -
> -static int mv64x60_wdt_remove(struct platform_device *dev)
> -{
> -	misc_deregister(&mv64x60_wdt_miscdev);
> -
> -	mv64x60_wdt_handler_disable();
> -
> -	return 0;
> -}
> -
> -static struct platform_driver mv64x60_wdt_driver = {
> -	.probe = mv64x60_wdt_probe,
> -	.remove = mv64x60_wdt_remove,
> -	.driver = {
> -		.name = MV64x60_WDT_NAME,
> -	},
> -};
> -
> -static int __init mv64x60_wdt_init(void)
> -{
> -	pr_info("MV64x60 watchdog driver\n");
> -
> -	return platform_driver_register(&mv64x60_wdt_driver);
> -}
> -
> -static void __exit mv64x60_wdt_exit(void)
> -{
> -	platform_driver_unregister(&mv64x60_wdt_driver);
> -}
> -
> -module_init(mv64x60_wdt_init);
> -module_exit(mv64x60_wdt_exit);
> -
> -MODULE_AUTHOR("James Chapman <jchapman@katalix.com>");
> -MODULE_DESCRIPTION("MV64x60 watchdog driver");
> -MODULE_LICENSE("GPL");
> -MODULE_ALIAS("platform:" MV64x60_WDT_NAME);
> diff --git a/include/linux/mv643xx.h b/include/linux/mv643xx.h
> index 47e5679b48e1..000b126acfb6 100644
> --- a/include/linux/mv643xx.h
> +++ b/include/linux/mv643xx.h
> @@ -918,12 +918,4 @@
>  
>  extern void mv64340_irq_init(unsigned int base);
>  
> -/* Watchdog Platform Device, Driver Data */
> -#define	MV64x60_WDT_NAME			"mv64x60_wdt"
> -
> -struct mv64x60_wdt_pdata {
> -	int	timeout;	/* watchdog expiry in seconds, default 10 */
> -	int	bus_clk;	/* bus clock in MHz, default 133 */
> -};
> -
>  #endif /* __ASM_MV643XX_H */
> 


^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH] watchdog: Remove MV64x60 watchdog driver
  2021-03-18 18:32 ` Guenter Roeck
@ 2021-05-17 11:17   ` Michael Ellerman
  2021-05-17 13:39     ` Guenter Roeck
  0 siblings, 1 reply; 7+ messages in thread
From: Michael Ellerman @ 2021-05-17 11:17 UTC (permalink / raw)
  To: Guenter Roeck, Christophe Leroy, Wim Van Sebroeck, Sebastian Hesselbarth
  Cc: linux-kernel, linuxppc-dev, linux-watchdog, netdev

Guenter Roeck <linux@roeck-us.net> writes:
> On 3/18/21 10:25 AM, Christophe Leroy wrote:
>> Commit 92c8c16f3457 ("powerpc/embedded6xx: Remove C2K board support")
>> removed the last selector of CONFIG_MV64X60.
>> 
>> Therefore CONFIG_MV64X60_WDT cannot be selected anymore and
>> can be removed.
>> 
>> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
>
> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
>
>> ---
>>  drivers/watchdog/Kconfig       |   4 -
>>  drivers/watchdog/Makefile      |   1 -
>>  drivers/watchdog/mv64x60_wdt.c | 324 ---------------------------------
>>  include/linux/mv643xx.h        |   8 -
>>  4 files changed, 337 deletions(-)
>>  delete mode 100644 drivers/watchdog/mv64x60_wdt.c

I assumed this would go via the watchdog tree, but seems like I
misinterpreted.

Should I take this via the powerpc tree for v5.14 ?

cheers

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH] watchdog: Remove MV64x60 watchdog driver
  2021-05-17 11:17   ` Michael Ellerman
@ 2021-05-17 13:39     ` Guenter Roeck
  2021-06-07  1:43       ` Michael Ellerman
  0 siblings, 1 reply; 7+ messages in thread
From: Guenter Roeck @ 2021-05-17 13:39 UTC (permalink / raw)
  To: Michael Ellerman, Christophe Leroy, Wim Van Sebroeck,
	Sebastian Hesselbarth
  Cc: linux-kernel, linuxppc-dev, linux-watchdog, netdev

On 5/17/21 4:17 AM, Michael Ellerman wrote:
> Guenter Roeck <linux@roeck-us.net> writes:
>> On 3/18/21 10:25 AM, Christophe Leroy wrote:
>>> Commit 92c8c16f3457 ("powerpc/embedded6xx: Remove C2K board support")
>>> removed the last selector of CONFIG_MV64X60.
>>>
>>> Therefore CONFIG_MV64X60_WDT cannot be selected anymore and
>>> can be removed.
>>>
>>> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
>>
>> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
>>
>>> ---
>>>   drivers/watchdog/Kconfig       |   4 -
>>>   drivers/watchdog/Makefile      |   1 -
>>>   drivers/watchdog/mv64x60_wdt.c | 324 ---------------------------------
>>>   include/linux/mv643xx.h        |   8 -
>>>   4 files changed, 337 deletions(-)
>>>   delete mode 100644 drivers/watchdog/mv64x60_wdt.c
> 
> I assumed this would go via the watchdog tree, but seems like I
> misinterpreted.
> 

Wim didn't send a pull request this time around.

Guenter

> Should I take this via the powerpc tree for v5.14 ?
> 
> cheers
> 


^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH] watchdog: Remove MV64x60 watchdog driver
  2021-05-17 13:39     ` Guenter Roeck
@ 2021-06-07  1:43       ` Michael Ellerman
  2021-06-07 11:29         ` Guenter Roeck
  0 siblings, 1 reply; 7+ messages in thread
From: Michael Ellerman @ 2021-06-07  1:43 UTC (permalink / raw)
  To: Guenter Roeck, Christophe Leroy, Wim Van Sebroeck, Sebastian Hesselbarth
  Cc: linux-kernel, linuxppc-dev, linux-watchdog, netdev

Guenter Roeck <linux@roeck-us.net> writes:
> On 5/17/21 4:17 AM, Michael Ellerman wrote:
>> Guenter Roeck <linux@roeck-us.net> writes:
>>> On 3/18/21 10:25 AM, Christophe Leroy wrote:
>>>> Commit 92c8c16f3457 ("powerpc/embedded6xx: Remove C2K board support")
>>>> removed the last selector of CONFIG_MV64X60.
>>>>
>>>> Therefore CONFIG_MV64X60_WDT cannot be selected anymore and
>>>> can be removed.
>>>>
>>>> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
>>>
>>> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
>>>
>>>> ---
>>>>   drivers/watchdog/Kconfig       |   4 -
>>>>   drivers/watchdog/Makefile      |   1 -
>>>>   drivers/watchdog/mv64x60_wdt.c | 324 ---------------------------------
>>>>   include/linux/mv643xx.h        |   8 -
>>>>   4 files changed, 337 deletions(-)
>>>>   delete mode 100644 drivers/watchdog/mv64x60_wdt.c
>> 
>> I assumed this would go via the watchdog tree, but seems like I
>> misinterpreted.
>> 
>
> Wim didn't send a pull request this time around.
>
> Guenter
>
>> Should I take this via the powerpc tree for v5.14 ?

I still don't see this in the watchdog tree, should I take it?

cheers

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH] watchdog: Remove MV64x60 watchdog driver
  2021-06-07  1:43       ` Michael Ellerman
@ 2021-06-07 11:29         ` Guenter Roeck
  2021-06-20 13:30           ` gituser
  0 siblings, 1 reply; 7+ messages in thread
From: Guenter Roeck @ 2021-06-07 11:29 UTC (permalink / raw)
  To: Michael Ellerman
  Cc: Christophe Leroy, Wim Van Sebroeck, Sebastian Hesselbarth,
	linux-kernel, linuxppc-dev, linux-watchdog, netdev

On Mon, Jun 07, 2021 at 11:43:26AM +1000, Michael Ellerman wrote:
> Guenter Roeck <linux@roeck-us.net> writes:
> > On 5/17/21 4:17 AM, Michael Ellerman wrote:
> >> Guenter Roeck <linux@roeck-us.net> writes:
> >>> On 3/18/21 10:25 AM, Christophe Leroy wrote:
> >>>> Commit 92c8c16f3457 ("powerpc/embedded6xx: Remove C2K board support")
> >>>> removed the last selector of CONFIG_MV64X60.
> >>>>
> >>>> Therefore CONFIG_MV64X60_WDT cannot be selected anymore and
> >>>> can be removed.
> >>>>
> >>>> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
> >>>
> >>> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> >>>
> >>>> ---
> >>>>   drivers/watchdog/Kconfig       |   4 -
> >>>>   drivers/watchdog/Makefile      |   1 -
> >>>>   drivers/watchdog/mv64x60_wdt.c | 324 ---------------------------------
> >>>>   include/linux/mv643xx.h        |   8 -
> >>>>   4 files changed, 337 deletions(-)
> >>>>   delete mode 100644 drivers/watchdog/mv64x60_wdt.c
> >> 
> >> I assumed this would go via the watchdog tree, but seems like I
> >> misinterpreted.
> >> 
> >
> > Wim didn't send a pull request this time around.
> >
> > Guenter
> >
> >> Should I take this via the powerpc tree for v5.14 ?
> 
> I still don't see this in the watchdog tree, should I take it?
> 
It is in my personal watchdog-next tree, but afaics Wim hasn't picked any
of it up yet. Wim ?

Thanks,
Guenter

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH] watchdog: Remove MV64x60 watchdog driver
  2021-06-07 11:29         ` Guenter Roeck
@ 2021-06-20 13:30           ` gituser
  0 siblings, 0 replies; 7+ messages in thread
From: gituser @ 2021-06-20 13:30 UTC (permalink / raw)
  To: Guenter Roeck
  Cc: Michael Ellerman, Christophe Leroy, Wim Van Sebroeck,
	Sebastian Hesselbarth, linux-kernel, linuxppc-dev,
	linux-watchdog, netdev

Hi All,

On Mon, Jun 07, 2021 at 04:29:50AM -0700, Guenter Roeck wrote:
> On Mon, Jun 07, 2021 at 11:43:26AM +1000, Michael Ellerman wrote:
> > Guenter Roeck <linux@roeck-us.net> writes:
> > > On 5/17/21 4:17 AM, Michael Ellerman wrote:
> > >> Guenter Roeck <linux@roeck-us.net> writes:
> > >>> On 3/18/21 10:25 AM, Christophe Leroy wrote:
> > >>>> Commit 92c8c16f3457 ("powerpc/embedded6xx: Remove C2K board support")
> > >>>> removed the last selector of CONFIG_MV64X60.
> > >>>>
> > >>>> Therefore CONFIG_MV64X60_WDT cannot be selected anymore and
> > >>>> can be removed.
> > >>>>
> > >>>> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
> > >>>
> > >>> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> > >>>
> > >>>> ---
> > >>>>   drivers/watchdog/Kconfig       |   4 -
> > >>>>   drivers/watchdog/Makefile      |   1 -
> > >>>>   drivers/watchdog/mv64x60_wdt.c | 324 ---------------------------------
> > >>>>   include/linux/mv643xx.h        |   8 -
> > >>>>   4 files changed, 337 deletions(-)
> > >>>>   delete mode 100644 drivers/watchdog/mv64x60_wdt.c
> > >> 
> > >> I assumed this would go via the watchdog tree, but seems like I
> > >> misinterpreted.
> > >> 
> > >
> > > Wim didn't send a pull request this time around.
> > >
> > > Guenter
> > >
> > >> Should I take this via the powerpc tree for v5.14 ?
> > 
> > I still don't see this in the watchdog tree, should I take it?
> > 
> It is in my personal watchdog-next tree, but afaics Wim hasn't picked any
> of it up yet. Wim ?

Picking it up right now.

Kind regards,
Wim.


^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2021-06-20 14:54 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-03-18 17:25 [PATCH] watchdog: Remove MV64x60 watchdog driver Christophe Leroy
2021-03-18 18:32 ` Guenter Roeck
2021-05-17 11:17   ` Michael Ellerman
2021-05-17 13:39     ` Guenter Roeck
2021-06-07  1:43       ` Michael Ellerman
2021-06-07 11:29         ` Guenter Roeck
2021-06-20 13:30           ` gituser

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).