Linux-Watchdog Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH] watchdog: sama5d4: fix WDD value to be always set to max
@ 2019-05-08 14:15 Eugen.Hristev
  2019-05-08 16:34 ` Guenter Roeck
  0 siblings, 1 reply; 3+ messages in thread
From: Eugen.Hristev @ 2019-05-08 14:15 UTC (permalink / raw)
  To: Nicolas.Ferre, linux-kernel, linux-arm-kernel, wim, linux,
	linux-watchdog
  Cc: Eugen.Hristev

From: Eugen Hristev <eugen.hristev@microchip.com>

WDD value must be always set to max (0xFFF) otherwise the hardware
block will reset the board on the first ping of the watchdog.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
---
 drivers/watchdog/sama5d4_wdt.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/watchdog/sama5d4_wdt.c b/drivers/watchdog/sama5d4_wdt.c
index 1e93c1b..d495336 100644
--- a/drivers/watchdog/sama5d4_wdt.c
+++ b/drivers/watchdog/sama5d4_wdt.c
@@ -111,9 +111,7 @@ static int sama5d4_wdt_set_timeout(struct watchdog_device *wdd,
 	u32 value = WDT_SEC2TICKS(timeout);
 
 	wdt->mr &= ~AT91_WDT_WDV;
-	wdt->mr &= ~AT91_WDT_WDD;
 	wdt->mr |= AT91_WDT_SET_WDV(value);
-	wdt->mr |= AT91_WDT_SET_WDD(value);
 
 	/*
 	 * WDDIS has to be 0 when updating WDD/WDV. The datasheet states: When
@@ -251,7 +249,7 @@ static int sama5d4_wdt_probe(struct platform_device *pdev)
 
 	timeout = WDT_SEC2TICKS(wdd->timeout);
 
-	wdt->mr |= AT91_WDT_SET_WDD(timeout);
+	wdt->mr |= AT91_WDT_SET_WDD(WDT_SEC2TICKS(MAX_WDT_TIMEOUT));
 	wdt->mr |= AT91_WDT_SET_WDV(timeout);
 
 	ret = sama5d4_wdt_init(wdt);
-- 
2.7.4


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH] watchdog: sama5d4: fix WDD value to be always set to max
  2019-05-08 14:15 [PATCH] watchdog: sama5d4: fix WDD value to be always set to max Eugen.Hristev
@ 2019-05-08 16:34 ` Guenter Roeck
  2019-05-09  6:04   ` Eugen.Hristev
  0 siblings, 1 reply; 3+ messages in thread
From: Guenter Roeck @ 2019-05-08 16:34 UTC (permalink / raw)
  To: Eugen.Hristev
  Cc: Nicolas.Ferre, linux-kernel, linux-arm-kernel, wim, linux-watchdog

On Wed, May 08, 2019 at 02:15:03PM +0000, Eugen.Hristev@microchip.com wrote:
> From: Eugen Hristev <eugen.hristev@microchip.com>
> 
> WDD value must be always set to max (0xFFF) otherwise the hardware
> block will reset the board on the first ping of the watchdog.
> 
Not sure why setting WDD to the same value as WDV would do that,
but on the other side it looks like setting WDD to anything but
the maximum doesn't add any value either, so

Reviewed-by: Guenter Roeck <linux@roeck-us.net>

Guenter

> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
> ---
>  drivers/watchdog/sama5d4_wdt.c | 4 +---
>  1 file changed, 1 insertion(+), 3 deletions(-)
> 
> diff --git a/drivers/watchdog/sama5d4_wdt.c b/drivers/watchdog/sama5d4_wdt.c
> index 1e93c1b..d495336 100644
> --- a/drivers/watchdog/sama5d4_wdt.c
> +++ b/drivers/watchdog/sama5d4_wdt.c
> @@ -111,9 +111,7 @@ static int sama5d4_wdt_set_timeout(struct watchdog_device *wdd,
>  	u32 value = WDT_SEC2TICKS(timeout);
>  
>  	wdt->mr &= ~AT91_WDT_WDV;
> -	wdt->mr &= ~AT91_WDT_WDD;
>  	wdt->mr |= AT91_WDT_SET_WDV(value);
> -	wdt->mr |= AT91_WDT_SET_WDD(value);
>  
>  	/*
>  	 * WDDIS has to be 0 when updating WDD/WDV. The datasheet states: When
> @@ -251,7 +249,7 @@ static int sama5d4_wdt_probe(struct platform_device *pdev)
>  
>  	timeout = WDT_SEC2TICKS(wdd->timeout);
>  
> -	wdt->mr |= AT91_WDT_SET_WDD(timeout);
> +	wdt->mr |= AT91_WDT_SET_WDD(WDT_SEC2TICKS(MAX_WDT_TIMEOUT));
>  	wdt->mr |= AT91_WDT_SET_WDV(timeout);
>  
>  	ret = sama5d4_wdt_init(wdt);
> -- 
> 2.7.4
> 

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH] watchdog: sama5d4: fix WDD value to be always set to max
  2019-05-08 16:34 ` Guenter Roeck
@ 2019-05-09  6:04   ` Eugen.Hristev
  0 siblings, 0 replies; 3+ messages in thread
From: Eugen.Hristev @ 2019-05-09  6:04 UTC (permalink / raw)
  To: linux; +Cc: Nicolas.Ferre, linux-kernel, linux-arm-kernel, wim, linux-watchdog



On 08.05.2019 19:34, Guenter Roeck wrote:
> On Wed, May 08, 2019 at 02:15:03PM +0000, Eugen.Hristev@microchip.com wrote:
>> From: Eugen Hristev <eugen.hristev@microchip.com>
>>
>> WDD value must be always set to max (0xFFF) otherwise the hardware
>> block will reset the board on the first ping of the watchdog.
>>
> Not sure why setting WDD to the same value as WDV would do that,
> but on the other side it looks like setting WDD to anything but
> the maximum doesn't add any value either, so

It's a hardware issue.
Normally, setting a WDD lower would allow the system for a little time 
to print out something, before the inevitable reset happens...
In our case, setting WDD lower than max would not allow a single 
watchdog feed, as the first attempt to write the CR would trigger the reset.
This bug was not obvious because the driver was always setting both WDD 
and WDV to max... until timeout-sec property came up in DT which changes 
this.

Eugen
> 
> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> 
> Guenter
> 
>> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
>> ---
>>   drivers/watchdog/sama5d4_wdt.c | 4 +---
>>   1 file changed, 1 insertion(+), 3 deletions(-)
>>
>> diff --git a/drivers/watchdog/sama5d4_wdt.c b/drivers/watchdog/sama5d4_wdt.c
>> index 1e93c1b..d495336 100644
>> --- a/drivers/watchdog/sama5d4_wdt.c
>> +++ b/drivers/watchdog/sama5d4_wdt.c
>> @@ -111,9 +111,7 @@ static int sama5d4_wdt_set_timeout(struct watchdog_device *wdd,
>>   	u32 value = WDT_SEC2TICKS(timeout);
>>   
>>   	wdt->mr &= ~AT91_WDT_WDV;
>> -	wdt->mr &= ~AT91_WDT_WDD;
>>   	wdt->mr |= AT91_WDT_SET_WDV(value);
>> -	wdt->mr |= AT91_WDT_SET_WDD(value);
>>   
>>   	/*
>>   	 * WDDIS has to be 0 when updating WDD/WDV. The datasheet states: When
>> @@ -251,7 +249,7 @@ static int sama5d4_wdt_probe(struct platform_device *pdev)
>>   
>>   	timeout = WDT_SEC2TICKS(wdd->timeout);
>>   
>> -	wdt->mr |= AT91_WDT_SET_WDD(timeout);
>> +	wdt->mr |= AT91_WDT_SET_WDD(WDT_SEC2TICKS(MAX_WDT_TIMEOUT));
>>   	wdt->mr |= AT91_WDT_SET_WDV(timeout);
>>   
>>   	ret = sama5d4_wdt_init(wdt);
>> -- 
>> 2.7.4
>>
> 
> 

^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, back to index

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-08 14:15 [PATCH] watchdog: sama5d4: fix WDD value to be always set to max Eugen.Hristev
2019-05-08 16:34 ` Guenter Roeck
2019-05-09  6:04   ` Eugen.Hristev

Linux-Watchdog Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-watchdog/0 linux-watchdog/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-watchdog linux-watchdog/ https://lore.kernel.org/linux-watchdog \
		linux-watchdog@vger.kernel.org linux-watchdog@archiver.kernel.org
	public-inbox-index linux-watchdog


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-watchdog


AGPL code for this site: git clone https://public-inbox.org/ public-inbox