From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from senator.holtmann.net ([87.106.208.187]:49975 "EHLO mail.holtmann.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751367AbZHAPZt (ORCPT ); Sat, 1 Aug 2009 11:25:49 -0400 Subject: Re: [PATCH 000/002] Fix frequent reconnects caused by new conection monitor From: Marcel Holtmann To: Maxim Levitsky Cc: reinette chatre , linux-wireless , linville , Johannes Berg In-Reply-To: <1249070739.25620.11.camel@maxim-laptop> References: <1249056817.20593.1.camel@maxim-laptop> <1249066338.30019.214.camel@rc-desk> <1249067293.19089.10.camel@maxim-laptop> <1249068449.23662.17.camel@localhost.localdomain> <1249070739.25620.11.camel@maxim-laptop> Content-Type: text/plain Date: Sat, 01 Aug 2009 08:25:45 -0700 Message-Id: <1249140345.3491.5.camel@localhost.localdomain> Mime-Version: 1.0 Sender: linux-wireless-owner@vger.kernel.org List-ID: Hi Maxim, > > > > > Hi, here is the updated version of these two patches that fix the > > > > > $SUBJECT issue. > > > > > > > > > > I attach these (in case mailer mangles them), and reply with patches. > > > > > > > > > > Tested both with low quality signal, and beacon loss. > > > > > Lack of TX is found, every 30 seconds now, and quite reliable. > > > > > Lack of beacons, triggers probe like it did every 2 seconds. > > > > > > > > Thanks! > > > > > > > > I've been running with this for two hours now with no disconnects. This > > > > is where before the patches I would get disconnected after a few > > > > minutes. I did get two "No probe response from AP xx:xx:xx:xx:xx:xx > > > > after 500ms, try 1" messages in my log. > > > This is normal, or at least can be normal, I patched the driver to > > > display this message, when there is a probe timeout, but instead of > > > disconnect, it retries, currently 5 times, but this can be even further > > > increased is necessarily. > > > (these messages are only in logs when verbose mac debugging is enabled) > > > > > > I don't know exactly why probes aren't answered, but I strongly suspect > > > that my AP sometimes 'goes out to lunch' and then answers, since > > > typically after a failed probe it sends many replies. > > > (Or it could be some buffering done by iwl3945 microcode). I currently > > > can't monitor the connection from outside, but as soon as I can I see > > > whether the above is true. Nevertheless if signal quality isn't great, > > > there are valid reasons for probe loss, and it shouldn't cause all the > > > fuzz (and since I use WPA2, every reconnection causes whole WPA > > > handshake to be preformed, and this takes at least 2 seconds, and if a > > > reconnection happens each 5 seconds, it gets very very annoying, and > > > almost unusable. > > > > I am testing your patches and so far so good. Seems to be working > > perfectly fine. I see this in the logs: > > > > [41027.333419] wlan0: detected beacon loss from AP - sending probe request > > [41027.389260] wlan0: cancelling probereq poll due to a received beacon > > [41027.793518] No probe response from AP 00:1c:f0:62:88:5b after 500ms, try 1 > > [41028.292731] No probe response from AP 00:1c:f0:62:88:5b after 500ms, try 2 > > > > Need to watch out if this pattern emerges and if the beacon loss trigger > > might give us an indication. Maybe the ucode is just not ready then. > Here (on my system) I see no beacon losses at all, like I said there > could be many reasons behind packet losses, and best way to mitigate > them is to retry. > > Your logs indicate that beacons weren't recieved for 2 seconds, then > mac80211 tried to send a probe, but a beacon is recieved before the > probe answer, this probe is canceled (at least should be) then after a > while, a probe request (same one?) is time outed, and retried twice, > then finally answered. it looked related, but it wasn't at all. I have this running for over 24 hours by now and the patches work perfectly fine. Today it saw for the first time a try 4 message. Otherwise it only had to try up to three times before it succeeded. Tested-by: Marcel Holtmann Regards Marcel