linux-wireless.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Bob Copeland <me@bobcopeland.com>
To: linville@tuxdriver.com
Cc: linux-wireless@vger.kernel.org, Bob Copeland <me@bobcopeland.com>
Subject: [PATCH 2/3] ath5k: trivial spelling fixes
Date: Sat, 21 Aug 2010 16:39:02 -0400	[thread overview]
Message-ID: <1282423143-4121-2-git-send-email-me@bobcopeland.com> (raw)
In-Reply-To: <1282423143-4121-1-git-send-email-me@bobcopeland.com>

Fix some comments:
    s/transmition/transmission/
    s/puting/putting/

Signed-off-by: Bob Copeland <me@bobcopeland.com>
---
 drivers/net/wireless/ath/ath5k/pcu.c   |    4 ++--
 drivers/net/wireless/ath/ath5k/phy.c   |    2 +-
 drivers/net/wireless/ath/ath5k/reset.c |    6 +++---
 3 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/ath/ath5k/pcu.c b/drivers/net/wireless/ath/ath5k/pcu.c
index 3fef593..bb2e215 100644
--- a/drivers/net/wireless/ath/ath5k/pcu.c
+++ b/drivers/net/wireless/ath/ath5k/pcu.c
@@ -137,11 +137,11 @@ void ath5k_hw_update_mib_counters(struct ath5k_hw *ah)
  * ath5k_hw_set_ack_bitrate - set bitrate for ACKs
  *
  * @ah: The &struct ath5k_hw
- * @high: Flag to determine if we want to use high transmition rate
+ * @high: Flag to determine if we want to use high transmission rate
  * for ACKs or not
  *
  * If high flag is set, we tell hw to use a set of control rates based on
- * the current transmition rate (check out control_rates array inside reset.c).
+ * the current transmission rate (check out control_rates array inside reset.c).
  * If not hw just uses the lowest rate available for the current modulation
  * scheme being used (1Mbit for CCK and 6Mbits for OFDM).
  */
diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c
index c7c4465..8c27a36 100644
--- a/drivers/net/wireless/ath/ath5k/phy.c
+++ b/drivers/net/wireless/ath/ath5k/phy.c
@@ -2987,7 +2987,7 @@ ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr,
 
 
 /*
- * Set transmition power
+ * Set transmission power
  */
 int
 ath5k_hw_txpower(struct ath5k_hw *ah, struct ieee80211_channel *channel,
diff --git a/drivers/net/wireless/ath/ath5k/reset.c b/drivers/net/wireless/ath/ath5k/reset.c
index 4154959..58912cd 100644
--- a/drivers/net/wireless/ath/ath5k/reset.c
+++ b/drivers/net/wireless/ath/ath5k/reset.c
@@ -326,7 +326,7 @@ commit:
  * register). After this MAC and Baseband are
  * disabled and a full reset is needed to come
  * back. This way we save as much power as possible
- * without puting the card on full sleep.
+ * without putting the card on full sleep.
  */
 int ath5k_hw_on_hold(struct ath5k_hw *ah)
 {
@@ -344,7 +344,7 @@ int ath5k_hw_on_hold(struct ath5k_hw *ah)
 	/*
 	 * Put chipset on warm reset...
 	 *
-	 * Note: puting PCI core on warm reset on PCI-E cards
+	 * Note: putting PCI core on warm reset on PCI-E cards
 	 * results card to hang and always return 0xffff... so
 	 * we ingore that flag for PCI-E cards. On PCI cards
 	 * this flag gets cleared after 64 PCI clocks.
@@ -400,7 +400,7 @@ int ath5k_hw_nic_wakeup(struct ath5k_hw *ah, int flags, bool initial)
 	/*
 	 * Put chipset on warm reset...
 	 *
-	 * Note: puting PCI core on warm reset on PCI-E cards
+	 * Note: putting PCI core on warm reset on PCI-E cards
 	 * results card to hang and always return 0xffff... so
 	 * we ingore that flag for PCI-E cards. On PCI cards
 	 * this flag gets cleared after 64 PCI clocks.
-- 
1.7.1.1



  reply	other threads:[~2010-08-21 20:39 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2010-08-21 20:39 [PATCH 1/3] mac80211: trivial spelling fixes Bob Copeland
2010-08-21 20:39 ` Bob Copeland [this message]
2010-08-21 20:39 ` [PATCH 3/3] ath5k: log descriptor chains at a new debug level Bob Copeland

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1282423143-4121-2-git-send-email-me@bobcopeland.com \
    --to=me@bobcopeland.com \
    --cc=linux-wireless@vger.kernel.org \
    --cc=linville@tuxdriver.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).