[PATCH] mac80211: do not actively scan DFS channels

[Antonio Quartulli <antonio@meshcoding.com>]

DFS channels should not be actively scanned as we can't be sure
if we are allowed or not.

If the current channel is in the DFS band, active scan might be
performed after CSA, but we have no guarantee about other channels,
therefore it is safer to prevent active scanning at all.

Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
---

this patch was: "mac80211: passively scan DFS channels if requested" and has
been changed after discussing with Johannes.


 net/mac80211/scan.c | 15 ++++++++++-----
 1 file changed, 10 insertions(+), 5 deletions(-)

diff --git a/net/mac80211/scan.c b/net/mac80211/scan.c
index 4aeca4b..46a5da0 100644
--- a/net/mac80211/scan.c
+++ b/net/mac80211/scan.c
@@ -599,7 +599,8 @@ static int __ieee80211_start_scan(struct ieee80211_sub_if_data *sdata,
 
 		if ((req->channels[0]->flags &
 		     IEEE80211_CHAN_NO_IR) ||
-		    !req->n_ssids) {
+		    !req->n_ssids ||
+		    (req->channels[0]->flags & IEEE80211_CHAN_RADAR)) {
 			next_delay = IEEE80211_PASSIVE_CHANNEL_TIME;
 		} else {
 			ieee80211_scan_state_send_probe(local, &next_delay);
@@ -639,13 +640,15 @@ static int __ieee80211_start_scan(struct ieee80211_sub_if_data *sdata,
 }
 
 static unsigned long
-ieee80211_scan_get_channel_time(struct ieee80211_channel *chan)
+ieee80211_scan_get_channel_time(struct ieee80211_channel *chan,
+				struct cfg80211_scan_request *scan_req)
 {
 	/*
 	 * TODO: channel switching also consumes quite some time,
 	 * add that delay as well to get a better estimation
 	 */
-	if (chan->flags & IEEE80211_CHAN_NO_IR)
+	if ((chan->flags & IEEE80211_CHAN_NO_IR) ||
+	    (chan->flags & IEEE80211_CHAN_RADAR))
 		return IEEE80211_PASSIVE_CHANNEL_TIME;
 	return IEEE80211_PROBE_DELAY + IEEE80211_CHANNEL_TIME;
 }
@@ -698,7 +701,8 @@ static void ieee80211_scan_state_decision(struct ieee80211_local *local,
 	 */
 
 	bad_latency = time_after(jiffies +
-				 ieee80211_scan_get_channel_time(next_chan),
+				 ieee80211_scan_get_channel_time(next_chan,
+								 scan_req),
 				 local->leave_oper_channel_time + HZ / 8);
 
 	if (associated && !tx_empty) {
@@ -777,7 +781,8 @@ static void ieee80211_scan_state_set_channel(struct ieee80211_local *local,
 	 *
 	 * In any case, it is not necessary for a passive scan.
 	 */
-	if (chan->flags & IEEE80211_CHAN_NO_IR || !scan_req->n_ssids) {
+	if (chan->flags & IEEE80211_CHAN_NO_IR || !scan_req->n_ssids ||
+	    (chan->flags & IEEE80211_CHAN_RADAR)) {
 		*next_delay = IEEE80211_PASSIVE_CHANNEL_TIME;
 		local->next_scan_state = SCAN_DECISION;
 		return;
-- 
2.6.3