[PATCH 00/10] wil6210 patches

[PATCH 00/10] wil6210 patches

[Maya Erez]

The following patches incude:
- wil6210 bug fixes
- Addition of runtime PM support

Dedy Lansky (2):
  wil6210: support FW RSSI reporting
  wil6210: store FW RF calibration result

Gidon Studinski (1):
  wil6210: make debugfs compilation optional

Hamad Kadmany (3):
  wil6210: protect against invalid length of tx management frame
  wil6210: allow configuring scan timers
  wil6210: fix interface-up check

Lazar Alexei (1):
  wil6210: run-time PM when interface down

Maya Erez (3):
  wil6210: check no_fw_recovery in resume failure recovery
  wil6210: add statistics for suspend time
  wil6210: notify wiphy on wowlan support

 drivers/net/wireless/ath/wil6210/cfg80211.c |  42 ++++++++--
 drivers/net/wireless/ath/wil6210/debugfs.c  | 121 +++++++++++++++++++++++++---
 drivers/net/wireless/ath/wil6210/ethtool.c  |  15 ++++
 drivers/net/wireless/ath/wil6210/main.c     |  12 ++-
 drivers/net/wireless/ath/wil6210/netdev.c   |  18 ++++-
 drivers/net/wireless/ath/wil6210/pcie_bus.c |  38 +++++++++
 drivers/net/wireless/ath/wil6210/pm.c       |  90 ++++++++++++++++++++-
 drivers/net/wireless/ath/wil6210/txrx.c     |   6 +-
 drivers/net/wireless/ath/wil6210/wil6210.h  |  31 ++++++-
 drivers/net/wireless/ath/wil6210/wmi.c      |  14 +++-
 drivers/net/wireless/ath/wil6210/wmi.h      |   8 +-
 11 files changed, 358 insertions(+), 37 deletions(-)

-- 
1.9.1

[PATCH 01/10] wil6210: protect against invalid length of tx management frame

[Maya Erez]

From: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>

Validate buffer length has the minimum needed size
when sending management frame to protect against
possible buffer overrun.

Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/cfg80211.c | 3 +++
 drivers/net/wireless/ath/wil6210/debugfs.c  | 3 +++
 2 files changed, 6 insertions(+)

diff --git a/drivers/net/wireless/ath/wil6210/cfg80211.c b/drivers/net/wireless/ath/wil6210/cfg80211.c
index 0b5383a..77af749 100644
--- a/drivers/net/wireless/ath/wil6210/cfg80211.c
+++ b/drivers/net/wireless/ath/wil6210/cfg80211.c
@@ -884,6 +884,9 @@ int wil_cfg80211_mgmt_tx(struct wiphy *wiphy, struct wireless_dev *wdev,
 	wil_hex_dump_misc("mgmt tx frame ", DUMP_PREFIX_OFFSET, 16, 1, buf,
 			  len, true);
 
+	if (len < sizeof(struct ieee80211_hdr_3addr))
+		return -EINVAL;
+
 	cmd = kmalloc(sizeof(*cmd) + len, GFP_KERNEL);
 	if (!cmd) {
 		rc = -ENOMEM;
diff --git a/drivers/net/wireless/ath/wil6210/debugfs.c b/drivers/net/wireless/ath/wil6210/debugfs.c
index f82506d..a2b5d59 100644
--- a/drivers/net/wireless/ath/wil6210/debugfs.c
+++ b/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -801,6 +801,9 @@ static ssize_t wil_write_file_txmgmt(struct file *file, const char __user *buf,
 	int rc;
 	void *frame;
 
+	if (!len)
+		return -EINVAL;
+
 	frame = memdup_user(buf, len);
 	if (IS_ERR(frame))
 		return PTR_ERR(frame);
-- 
1.9.1

[PATCH 02/10] wil6210: allow configuring scan timers

[Maya Erez]

From: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>

Allow setting scan timeout and scan dwell time
through module parameters.

Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/cfg80211.c | 17 ++++++++++++++---
 drivers/net/wireless/ath/wil6210/wil6210.h  |  2 +-
 2 files changed, 15 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/ath/wil6210/cfg80211.c b/drivers/net/wireless/ath/wil6210/cfg80211.c
index 77af749..d079533 100644
--- a/drivers/net/wireless/ath/wil6210/cfg80211.c
+++ b/drivers/net/wireless/ath/wil6210/cfg80211.c
@@ -26,6 +26,14 @@
 module_param(disable_ap_sme, bool, 0444);
 MODULE_PARM_DESC(disable_ap_sme, " let user space handle AP mode SME");
 
+static uint scan_dwell_time  = WMI_SCAN_DWELL_TIME_MS;
+module_param(scan_dwell_time, uint, 0644);
+MODULE_PARM_DESC(scan_dwell_time, " Scan dwell time (msec)");
+
+static uint scan_timeout = WIL6210_SCAN_TO_SEC;
+module_param(scan_timeout, uint, 0644);
+MODULE_PARM_DESC(scan_timeout, " Scan timeout (seconds)");
+
 #define CHAN60G(_channel, _flags) {				\
 	.band			= NL80211_BAND_60GHZ,		\
 	.center_freq		= 56160 + (2160 * (_channel)),	\
@@ -528,8 +536,9 @@ static int wil_cfg80211_scan(struct wiphy *wiphy,
 
 	(void)wil_p2p_stop_discovery(wil);
 
-	wil_dbg_misc(wil, "Start scan_request 0x%p\n", request);
-	wil_dbg_misc(wil, "SSID count: %d", request->n_ssids);
+	wil_dbg_misc(wil,
+		     "Start scan_request 0x%p, dwell_time %dms, timeout %dsec, SSID count %d\n",
+		     request, scan_dwell_time, scan_timeout, request->n_ssids);
 
 	for (i = 0; i < request->n_ssids; i++) {
 		wil_dbg_misc(wil, "SSID[%d]", i);
@@ -550,10 +559,12 @@ static int wil_cfg80211_scan(struct wiphy *wiphy,
 	}
 
 	wil->scan_request = request;
-	mod_timer(&wil->scan_timer, jiffies + WIL6210_SCAN_TO);
+	mod_timer(&wil->scan_timer,
+		  jiffies + msecs_to_jiffies(1000U * scan_timeout));
 
 	memset(&cmd, 0, sizeof(cmd));
 	cmd.cmd.scan_type = WMI_ACTIVE_SCAN;
+	cmd.cmd.dwell_time = cpu_to_le32(scan_dwell_time);
 	cmd.cmd.num_channels = 0;
 	n = min(request->n_channels, 4U);
 	for (i = 0; i < n; i++) {
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index d085ccf..ac32284 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -112,7 +112,7 @@ static inline u32 wil_mtu2macbuf(u32 mtu)
 #define WIL6210_ITR_RX_MAX_BURST_DURATION_DEFAULT (500) /* usec */
 #define WIL6210_FW_RECOVERY_RETRIES	(5) /* try to recover this many times */
 #define WIL6210_FW_RECOVERY_TO	msecs_to_jiffies(5000)
-#define WIL6210_SCAN_TO		msecs_to_jiffies(10000)
+#define WIL6210_SCAN_TO_SEC		10
 #define WIL6210_DISCONNECT_TO_MS (2000)
 #define WIL6210_RX_HIGH_TRSH_INIT		(0)
 #define WIL6210_RX_HIGH_TRSH_DEFAULT \
-- 
1.9.1

[PATCH 03/10] wil6210: support FW RSSI reporting

[Maya Erez]

From: Dedy Lansky <qca_dlansky@qca.qualcomm.com>

New FW supports reporting RSSI signal in dBm.
Report RSSI to kernel in case FW has this capability.

Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/cfg80211.c | 12 ++++++++----
 drivers/net/wireless/ath/wil6210/debugfs.c  |  2 ++
 drivers/net/wireless/ath/wil6210/pcie_bus.c |  3 +++
 drivers/net/wireless/ath/wil6210/wmi.c      |  9 ++++++---
 drivers/net/wireless/ath/wil6210/wmi.h      |  6 ++++--
 5 files changed, 23 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/wil6210/cfg80211.c b/drivers/net/wireless/ath/wil6210/cfg80211.c
index d079533..c860c0c 100644
--- a/drivers/net/wireless/ath/wil6210/cfg80211.c
+++ b/drivers/net/wireless/ath/wil6210/cfg80211.c
@@ -281,12 +281,12 @@ int wil_cid_fill_sinfo(struct wil6210_priv *wil, int cid,
 
 	wil_dbg_wmi(wil, "Link status for CID %d: {\n"
 		    "  MCS %d TSF 0x%016llx\n"
-		    "  BF status 0x%08x SNR 0x%08x SQI %d%%\n"
+		    "  BF status 0x%08x RSSI %d SQI %d%%\n"
 		    "  Tx Tpt %d goodput %d Rx goodput %d\n"
 		    "  Sectors(rx:tx) my %d:%d peer %d:%d\n""}\n",
 		    cid, le16_to_cpu(reply.evt.bf_mcs),
 		    le64_to_cpu(reply.evt.tsf), reply.evt.status,
-		    le32_to_cpu(reply.evt.snr_val),
+		    reply.evt.rssi,
 		    reply.evt.sqi,
 		    le32_to_cpu(reply.evt.tx_tpt),
 		    le32_to_cpu(reply.evt.tx_goodput),
@@ -319,7 +319,11 @@ int wil_cid_fill_sinfo(struct wil6210_priv *wil, int cid,
 
 	if (test_bit(wil_status_fwconnected, wil->status)) {
 		sinfo->filled |= BIT(NL80211_STA_INFO_SIGNAL);
-		sinfo->signal = reply.evt.sqi;
+		if (test_bit(WMI_FW_CAPABILITY_RSSI_REPORTING,
+			     wil->fw_capabilities))
+			sinfo->signal = reply.evt.rssi;
+		else
+			sinfo->signal = reply.evt.sqi;
 	}
 
 	return rc;
@@ -1805,7 +1809,7 @@ static void wil_wiphy_init(struct wiphy *wiphy)
 
 	wiphy->bands[NL80211_BAND_60GHZ] = &wil_band_60ghz;
 
-	/* TODO: figure this out */
+	/* may change after reading FW capabilities */
 	wiphy->signal_type = CFG80211_SIGNAL_TYPE_UNSPEC;
 
 	wiphy->cipher_suites = wil_cipher_suites;
diff --git a/drivers/net/wireless/ath/wil6210/debugfs.c b/drivers/net/wireless/ath/wil6210/debugfs.c
index a2b5d59..21b6611 100644
--- a/drivers/net/wireless/ath/wil6210/debugfs.c
+++ b/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -1016,6 +1016,7 @@ static int wil_bf_debugfs_show(struct seq_file *s, void *data)
 			   "  TSF = 0x%016llx\n"
 			   "  TxMCS = %2d TxTpt = %4d\n"
 			   "  SQI = %4d\n"
+			   "  RSSI = %4d\n"
 			   "  Status = 0x%08x %s\n"
 			   "  Sectors(rx:tx) my %2d:%2d peer %2d:%2d\n"
 			   "  Goodput(rx:tx) %4d:%4d\n"
@@ -1025,6 +1026,7 @@ static int wil_bf_debugfs_show(struct seq_file *s, void *data)
 			   le16_to_cpu(reply.evt.bf_mcs),
 			   le32_to_cpu(reply.evt.tx_tpt),
 			   reply.evt.sqi,
+			   reply.evt.rssi,
 			   status, wil_bfstatus_str(status),
 			   le16_to_cpu(reply.evt.my_rx_sector),
 			   le16_to_cpu(reply.evt.my_tx_sector),
diff --git a/drivers/net/wireless/ath/wil6210/pcie_bus.c b/drivers/net/wireless/ath/wil6210/pcie_bus.c
index d571feb..6a3ab4b 100644
--- a/drivers/net/wireless/ath/wil6210/pcie_bus.c
+++ b/drivers/net/wireless/ath/wil6210/pcie_bus.c
@@ -84,6 +84,9 @@ void wil_set_capabilities(struct wil6210_priv *wil)
 
 	/* extract FW capabilities from file without loading the FW */
 	wil_request_firmware(wil, wil->wil_fw_name, false);
+
+	if (test_bit(WMI_FW_CAPABILITY_RSSI_REPORTING, wil->fw_capabilities))
+		wil_to_wiphy(wil)->signal_type = CFG80211_SIGNAL_TYPE_MBM;
 }
 
 void wil_disable_irq(struct wil6210_priv *wil)
diff --git a/drivers/net/wireless/ath/wil6210/wmi.c b/drivers/net/wireless/ath/wil6210/wmi.c
index 65ef673..a9487f2 100644
--- a/drivers/net/wireless/ath/wil6210/wmi.c
+++ b/drivers/net/wireless/ath/wil6210/wmi.c
@@ -381,12 +381,15 @@ static void wmi_evt_rx_mgmt(struct wil6210_priv *wil, int id, void *d, int len)
 	ch_no = data->info.channel + 1;
 	freq = ieee80211_channel_to_frequency(ch_no, NL80211_BAND_60GHZ);
 	channel = ieee80211_get_channel(wiphy, freq);
-	signal = data->info.sqi;
+	if (test_bit(WMI_FW_CAPABILITY_RSSI_REPORTING, wil->fw_capabilities))
+		signal = 100 * data->info.rssi;
+	else
+		signal = data->info.sqi;
 	d_status = le16_to_cpu(data->info.status);
 	fc = rx_mgmt_frame->frame_control;
 
-	wil_dbg_wmi(wil, "MGMT Rx: channel %d MCS %d SNR %d SQI %d%%\n",
-		    data->info.channel, data->info.mcs, data->info.snr,
+	wil_dbg_wmi(wil, "MGMT Rx: channel %d MCS %d RSSI %d SQI %d%%\n",
+		    data->info.channel, data->info.mcs, data->info.rssi,
 		    data->info.sqi);
 	wil_dbg_wmi(wil, "status 0x%04x len %d fc 0x%04x\n", d_status, d_len,
 		    le16_to_cpu(fc));
diff --git a/drivers/net/wireless/ath/wil6210/wmi.h b/drivers/net/wireless/ath/wil6210/wmi.h
index 256f63c..4e31c2f 100644
--- a/drivers/net/wireless/ath/wil6210/wmi.h
+++ b/drivers/net/wireless/ath/wil6210/wmi.h
@@ -60,6 +60,7 @@ enum wmi_fw_capability {
 	WMI_FW_CAPABILITY_WMI_ONLY		= 5,
 	WMI_FW_CAPABILITY_THERMAL_THROTTLING	= 7,
 	WMI_FW_CAPABILITY_D3_SUSPEND		= 8,
+	WMI_FW_CAPABILITY_RSSI_REPORTING	= 12,
 	WMI_FW_CAPABILITY_MAX,
 };
 
@@ -1306,7 +1307,8 @@ struct wmi_notify_req_done_event {
 	/* beamforming status, 0: fail; 1: OK; 2: retrying */
 	__le32 status;
 	__le64 tsf;
-	__le32 snr_val;
+	s8 rssi;
+	u8 reserved0[3];
 	__le32 tx_tpt;
 	__le32 tx_goodput;
 	__le32 rx_goodput;
@@ -1602,7 +1604,7 @@ struct wmi_get_ssid_event {
 /* wmi_rx_mgmt_info */
 struct wmi_rx_mgmt_info {
 	u8 mcs;
-	s8 snr;
+	s8 rssi;
 	u8 range;
 	u8 sqi;
 	__le16 stype;
-- 
1.9.1

[PATCH 04/10] wil6210: check no_fw_recovery in resume failure recovery

[Maya Erez]

Reset 11ad device on resume failure only if no_fw_recovery
is not set.

Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/pm.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/wil6210/pm.c b/drivers/net/wireless/ath/wil6210/pm.c
index ce1f384..4548829 100644
--- a/drivers/net/wireless/ath/wil6210/pm.c
+++ b/drivers/net/wireless/ath/wil6210/pm.c
@@ -85,7 +85,9 @@ static int wil_resume_keep_radio_on(struct wil6210_priv *wil)
 	/* Send WMI resume request to the device */
 	rc = wmi_resume(wil);
 	if (rc) {
-		wil_err(wil, "device failed to resume (%d), resetting\n", rc);
+		wil_err(wil, "device failed to resume (%d)\n", rc);
+		if (no_fw_recovery)
+			goto out;
 		rc = wil_down(wil);
 		if (rc) {
 			wil_err(wil, "wil_down failed (%d)\n", rc);
-- 
1.9.1

[PATCH 05/10] wil6210: run-time PM when interface down

[Maya Erez]

From: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>

Allow run-time suspend when interface is down, keep card alive when
interface is up.
If driver is in wmi only or debug_fw mode run-time PM won't suspend.

Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/debugfs.c  | 85 ++++++++++++++++++++++++++---
 drivers/net/wireless/ath/wil6210/ethtool.c  | 15 +++++
 drivers/net/wireless/ath/wil6210/netdev.c   | 18 +++++-
 drivers/net/wireless/ath/wil6210/pcie_bus.c | 35 ++++++++++++
 drivers/net/wireless/ath/wil6210/pm.c       | 62 +++++++++++++++++++++
 drivers/net/wireless/ath/wil6210/wil6210.h  | 16 ++++++
 6 files changed, 222 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/wil6210/debugfs.c b/drivers/net/wireless/ath/wil6210/debugfs.c
index 21b6611..8a0e64c 100644
--- a/drivers/net/wireless/ath/wil6210/debugfs.c
+++ b/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -244,12 +244,19 @@ static void wil_print_ring(struct seq_file *s, const char *prefix,
 static int wil_mbox_debugfs_show(struct seq_file *s, void *data)
 {
 	struct wil6210_priv *wil = s->private;
+	int ret;
+
+	ret = wil_pm_runtime_get(wil);
+	if (ret < 0)
+		return ret;
 
 	wil_print_ring(s, "tx", wil->csr + HOST_MBOX +
 		       offsetof(struct wil6210_mbox_ctl, tx));
 	wil_print_ring(s, "rx", wil->csr + HOST_MBOX +
 		       offsetof(struct wil6210_mbox_ctl, rx));
 
+	wil_pm_runtime_put(wil);
+
 	return 0;
 }
 
@@ -267,15 +274,37 @@ static int wil_mbox_seq_open(struct inode *inode, struct file *file)
 
 static int wil_debugfs_iomem_x32_set(void *data, u64 val)
 {
-	writel(val, (void __iomem *)data);
+	struct wil_debugfs_iomem_data *d = (struct
+					    wil_debugfs_iomem_data *)data;
+	struct wil6210_priv *wil = d->wil;
+	int ret;
+
+	ret = wil_pm_runtime_get(wil);
+	if (ret < 0)
+		return ret;
+
+	writel(val, (void __iomem *)d->offset);
 	wmb(); /* make sure write propagated to HW */
 
+	wil_pm_runtime_put(wil);
+
 	return 0;
 }
 
 static int wil_debugfs_iomem_x32_get(void *data, u64 *val)
 {
-	*val = readl((void __iomem *)data);
+	struct wil_debugfs_iomem_data *d = (struct
+					    wil_debugfs_iomem_data *)data;
+	struct wil6210_priv *wil = d->wil;
+	int ret;
+
+	ret = wil_pm_runtime_get(wil);
+	if (ret < 0)
+		return ret;
+
+	*val = readl((void __iomem *)d->offset);
+
+	wil_pm_runtime_put(wil);
 
 	return 0;
 }
@@ -286,10 +315,21 @@ static int wil_debugfs_iomem_x32_get(void *data, u64 *val)
 static struct dentry *wil_debugfs_create_iomem_x32(const char *name,
 						   umode_t mode,
 						   struct dentry *parent,
-						   void *value)
+						   void *value,
+						   struct wil6210_priv *wil)
 {
-	return debugfs_create_file(name, mode, parent, value,
-				   &fops_iomem_x32);
+	struct dentry *file;
+	struct wil_debugfs_iomem_data *data = &wil->dbg_data.data_arr[
+					      wil->dbg_data.iomem_data_count];
+
+	data->wil = wil;
+	data->offset = value;
+
+	file = debugfs_create_file(name, mode, parent, data, &fops_iomem_x32);
+	if (!IS_ERR_OR_NULL(file))
+		wil->dbg_data.iomem_data_count++;
+
+	return file;
 }
 
 static int wil_debugfs_ulong_set(void *data, u64 val)
@@ -348,7 +388,8 @@ static void wil6210_debugfs_init_offset(struct wil6210_priv *wil,
 		case doff_io32:
 			f = wil_debugfs_create_iomem_x32(tbl[i].name,
 							 tbl[i].mode, dbg,
-							 base + tbl[i].off);
+							 base + tbl[i].off,
+							 wil);
 			break;
 		case doff_u8:
 			f = debugfs_create_u8(tbl[i].name, tbl[i].mode, dbg,
@@ -504,10 +545,12 @@ static ssize_t wil_read_file_ioblob(struct file *file, char __user *user_buf,
 {
 	enum { max_count = 4096 };
 	struct wil_blob_wrapper *wil_blob = file->private_data;
+	struct wil6210_priv *wil = wil_blob->wil;
 	loff_t pos = *ppos;
 	size_t available = wil_blob->blob.size;
 	void *buf;
 	size_t ret;
+	int rc;
 
 	if (test_bit(wil_status_suspending, wil_blob->wil->status) ||
 	    test_bit(wil_status_suspended, wil_blob->wil->status))
@@ -528,10 +571,19 @@ static ssize_t wil_read_file_ioblob(struct file *file, char __user *user_buf,
 	if (!buf)
 		return -ENOMEM;
 
+	rc = wil_pm_runtime_get(wil);
+	if (rc < 0) {
+		kfree(buf);
+		return rc;
+	}
+
 	wil_memcpy_fromio_32(buf, (const void __iomem *)
 			     wil_blob->blob.data + pos, count);
 
 	ret = copy_to_user(user_buf, buf, count);
+
+	wil_pm_runtime_put(wil);
+
 	kfree(buf);
 	if (ret == count)
 		return -EFAULT;
@@ -1773,14 +1825,31 @@ static void wil6210_debugfs_init_isr(struct wil6210_priv *wil,
 	{},
 };
 
+static const int dbg_off_count = 4 * (ARRAY_SIZE(isr_off) - 1) +
+				ARRAY_SIZE(dbg_wil_regs) - 1 +
+				ARRAY_SIZE(pseudo_isr_off) - 1 +
+				ARRAY_SIZE(lgc_itr_cnt_off) - 1 +
+				ARRAY_SIZE(tx_itr_cnt_off) - 1 +
+				ARRAY_SIZE(rx_itr_cnt_off) - 1;
+
 int wil6210_debugfs_init(struct wil6210_priv *wil)
 {
 	struct dentry *dbg = wil->debug = debugfs_create_dir(WIL_NAME,
 			wil_to_wiphy(wil)->debugfsdir);
-
 	if (IS_ERR_OR_NULL(dbg))
 		return -ENODEV;
 
+	wil->dbg_data.data_arr = kcalloc(dbg_off_count,
+					 sizeof(struct wil_debugfs_iomem_data),
+					 GFP_KERNEL);
+	if (!wil->dbg_data.data_arr) {
+		debugfs_remove_recursive(dbg);
+		wil->debug = NULL;
+		return -ENOMEM;
+	}
+
+	wil->dbg_data.iomem_data_count = 0;
+
 	wil_pmc_init(wil);
 
 	wil6210_debugfs_init_files(wil, dbg);
@@ -1803,6 +1872,8 @@ void wil6210_debugfs_remove(struct wil6210_priv *wil)
 	debugfs_remove_recursive(wil->debug);
 	wil->debug = NULL;
 
+	kfree(wil->dbg_data.data_arr);
+
 	/* free pmc memory without sending command to fw, as it will
 	 * be reset on the way down anyway
 	 */
diff --git a/drivers/net/wireless/ath/wil6210/ethtool.c b/drivers/net/wireless/ath/wil6210/ethtool.c
index adcfef4..66200f6 100644
--- a/drivers/net/wireless/ath/wil6210/ethtool.c
+++ b/drivers/net/wireless/ath/wil6210/ethtool.c
@@ -47,9 +47,14 @@ static int wil_ethtoolops_get_coalesce(struct net_device *ndev,
 	struct wil6210_priv *wil = ndev_to_wil(ndev);
 	u32 tx_itr_en, tx_itr_val = 0;
 	u32 rx_itr_en, rx_itr_val = 0;
+	int ret;
 
 	wil_dbg_misc(wil, "ethtoolops_get_coalesce\n");
 
+	ret = wil_pm_runtime_get(wil);
+	if (ret < 0)
+		return ret;
+
 	tx_itr_en = wil_r(wil, RGF_DMA_ITR_TX_CNT_CTL);
 	if (tx_itr_en & BIT_DMA_ITR_TX_CNT_CTL_EN)
 		tx_itr_val = wil_r(wil, RGF_DMA_ITR_TX_CNT_TRSH);
@@ -58,6 +63,8 @@ static int wil_ethtoolops_get_coalesce(struct net_device *ndev,
 	if (rx_itr_en & BIT_DMA_ITR_RX_CNT_CTL_EN)
 		rx_itr_val = wil_r(wil, RGF_DMA_ITR_RX_CNT_TRSH);
 
+	wil_pm_runtime_put(wil);
+
 	cp->tx_coalesce_usecs = tx_itr_val;
 	cp->rx_coalesce_usecs = rx_itr_val;
 	return 0;
@@ -67,6 +74,7 @@ static int wil_ethtoolops_set_coalesce(struct net_device *ndev,
 				       struct ethtool_coalesce *cp)
 {
 	struct wil6210_priv *wil = ndev_to_wil(ndev);
+	int ret;
 
 	wil_dbg_misc(wil, "ethtoolops_set_coalesce: rx %d usec, tx %d usec\n",
 		     cp->rx_coalesce_usecs, cp->tx_coalesce_usecs);
@@ -86,8 +94,15 @@ static int wil_ethtoolops_set_coalesce(struct net_device *ndev,
 
 	wil->tx_max_burst_duration = cp->tx_coalesce_usecs;
 	wil->rx_max_burst_duration = cp->rx_coalesce_usecs;
+
+	ret = wil_pm_runtime_get(wil);
+	if (ret < 0)
+		return ret;
+
 	wil_configure_interrupt_moderation(wil);
 
+	wil_pm_runtime_put(wil);
+
 	return 0;
 
 out_bad:
diff --git a/drivers/net/wireless/ath/wil6210/netdev.c b/drivers/net/wireless/ath/wil6210/netdev.c
index 4a6ab2d..b641ac1 100644
--- a/drivers/net/wireless/ath/wil6210/netdev.c
+++ b/drivers/net/wireless/ath/wil6210/netdev.c
@@ -21,6 +21,7 @@
 static int wil_open(struct net_device *ndev)
 {
 	struct wil6210_priv *wil = ndev_to_wil(ndev);
+	int rc;
 
 	wil_dbg_misc(wil, "open\n");
 
@@ -30,16 +31,29 @@ static int wil_open(struct net_device *ndev)
 		return -EINVAL;
 	}
 
-	return wil_up(wil);
+	rc = wil_pm_runtime_get(wil);
+	if (rc < 0)
+		return rc;
+
+	rc = wil_up(wil);
+	if (rc)
+		wil_pm_runtime_put(wil);
+
+	return rc;
 }
 
 static int wil_stop(struct net_device *ndev)
 {
 	struct wil6210_priv *wil = ndev_to_wil(ndev);
+	int rc;
 
 	wil_dbg_misc(wil, "stop\n");
 
-	return wil_down(wil);
+	rc = wil_down(wil);
+	if (!rc)
+		wil_pm_runtime_put(wil);
+
+	return rc;
 }
 
 static const struct net_device_ops wil_netdev_ops = {
diff --git a/drivers/net/wireless/ath/wil6210/pcie_bus.c b/drivers/net/wireless/ath/wil6210/pcie_bus.c
index 6a3ab4b..560a737 100644
--- a/drivers/net/wireless/ath/wil6210/pcie_bus.c
+++ b/drivers/net/wireless/ath/wil6210/pcie_bus.c
@@ -21,6 +21,7 @@
 #include <linux/suspend.h>
 #include "wil6210.h"
 #include <linux/rtnetlink.h>
+#include <linux/pm_runtime.h>
 
 static bool use_msi = true;
 module_param(use_msi, bool, 0444);
@@ -334,6 +335,8 @@ static int wil_pcie_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	wil6210_debugfs_init(wil);
 
 
+	wil_pm_runtime_allow(wil);
+
 	return 0;
 
 bus_disable:
@@ -365,6 +368,8 @@ static void wil_pcie_remove(struct pci_dev *pdev)
 #endif /* CONFIG_PM_SLEEP */
 #endif /* CONFIG_PM */
 
+	wil_pm_runtime_forbid(wil);
+
 	wil6210_debugfs_remove(wil);
 	rtnl_lock();
 	wil_p2p_wdev_free(wil);
@@ -492,10 +497,40 @@ static int wil6210_pm_resume(struct device *dev)
 }
 #endif /* CONFIG_PM_SLEEP */
 
+static int wil6210_pm_runtime_idle(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct wil6210_priv *wil = pci_get_drvdata(pdev);
+
+	wil_dbg_pm(wil, "Runtime idle\n");
+
+	return wil_can_suspend(wil, true);
+}
+
+static int wil6210_pm_runtime_resume(struct device *dev)
+{
+	return wil6210_resume(dev, true);
+}
+
+static int wil6210_pm_runtime_suspend(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct wil6210_priv *wil = pci_get_drvdata(pdev);
+
+	if (test_bit(wil_status_suspended, wil->status)) {
+		wil_dbg_pm(wil, "trying to suspend while suspended\n");
+		return 1;
+	}
+
+	return wil6210_suspend(dev, true);
+}
 #endif /* CONFIG_PM */
 
 static const struct dev_pm_ops wil6210_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(wil6210_pm_suspend, wil6210_pm_resume)
+	SET_RUNTIME_PM_OPS(wil6210_pm_runtime_suspend,
+			   wil6210_pm_runtime_resume,
+			   wil6210_pm_runtime_idle)
 };
 
 static struct pci_driver wil6210_driver = {
diff --git a/drivers/net/wireless/ath/wil6210/pm.c b/drivers/net/wireless/ath/wil6210/pm.c
index 4548829..976c9aa 100644
--- a/drivers/net/wireless/ath/wil6210/pm.c
+++ b/drivers/net/wireless/ath/wil6210/pm.c
@@ -16,14 +16,25 @@
 
 #include "wil6210.h"
 #include <linux/jiffies.h>
+#include <linux/pm_runtime.h>
+
+#define WIL6210_AUTOSUSPEND_DELAY_MS (1000)
 
 int wil_can_suspend(struct wil6210_priv *wil, bool is_runtime)
 {
 	int rc = 0;
 	struct wireless_dev *wdev = wil->wdev;
+	bool wmi_only = test_bit(WMI_FW_CAPABILITY_WMI_ONLY,
+				 wil->fw_capabilities);
 
 	wil_dbg_pm(wil, "can_suspend: %s\n", is_runtime ? "runtime" : "system");
 
+	if (wmi_only || debug_fw) {
+		wil_dbg_pm(wil, "Deny any suspend - %s mode\n",
+			   wmi_only ? "wmi_only" : "debug_fw");
+		rc = -EPERM;
+		goto out;
+	}
 	if (!netif_running(wil_to_ndev(wil))) {
 		/* can always sleep when down */
 		wil_dbg_pm(wil, "Interface is down\n");
@@ -43,6 +54,10 @@ int wil_can_suspend(struct wil6210_priv *wil, bool is_runtime)
 	/* interface is running */
 	switch (wdev->iftype) {
 	case NL80211_IFTYPE_MONITOR:
+		wil_dbg_pm(wil, "Sniffer\n");
+		rc = -EBUSY;
+		goto out;
+	/* for STA-like interface, don't runtime suspend */
 	case NL80211_IFTYPE_STATION:
 	case NL80211_IFTYPE_P2P_CLIENT:
 		if (test_bit(wil_status_fwconnecting, wil->status)) {
@@ -50,6 +65,12 @@ int wil_can_suspend(struct wil6210_priv *wil, bool is_runtime)
 			rc = -EBUSY;
 			goto out;
 		}
+		/* Runtime pm not supported in case the interface is up */
+		if (is_runtime) {
+			wil_dbg_pm(wil, "STA-like interface\n");
+			rc = -EBUSY;
+			goto out;
+		}
 		break;
 	/* AP-like interface - can't suspend */
 	default:
@@ -331,3 +352,44 @@ int wil_resume(struct wil6210_priv *wil, bool is_runtime)
 		   is_runtime ? "runtime" : "system", rc);
 	return rc;
 }
+
+void wil_pm_runtime_allow(struct wil6210_priv *wil)
+{
+	struct device *dev = wil_to_dev(wil);
+
+	pm_runtime_put_noidle(dev);
+	pm_runtime_set_autosuspend_delay(dev, WIL6210_AUTOSUSPEND_DELAY_MS);
+	pm_runtime_use_autosuspend(dev);
+	pm_runtime_allow(dev);
+}
+
+void wil_pm_runtime_forbid(struct wil6210_priv *wil)
+{
+	struct device *dev = wil_to_dev(wil);
+
+	pm_runtime_forbid(dev);
+	pm_runtime_get_noresume(dev);
+}
+
+int wil_pm_runtime_get(struct wil6210_priv *wil)
+{
+	int rc;
+	struct device *dev = wil_to_dev(wil);
+
+	rc = pm_runtime_get_sync(dev);
+	if (rc < 0) {
+		wil_err(wil, "pm_runtime_get_sync() failed, rc = %d\n", rc);
+		pm_runtime_put_noidle(dev);
+		return rc;
+	}
+
+	return 0;
+}
+
+void wil_pm_runtime_put(struct wil6210_priv *wil)
+{
+	struct device *dev = wil_to_dev(wil);
+
+	pm_runtime_mark_last_busy(dev);
+	pm_runtime_put_autosuspend(dev);
+}
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index ac32284..69103b0 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -607,6 +607,16 @@ struct blink_on_off_time {
 	u32 off_ms;
 };
 
+struct wil_debugfs_iomem_data {
+	void *offset;
+	struct wil6210_priv *wil;
+};
+
+struct wil_debugfs_data {
+	struct wil_debugfs_iomem_data *data_arr;
+	int iomem_data_count;
+};
+
 extern struct blink_on_off_time led_blink_time[WIL_LED_TIME_LAST];
 extern u8 led_id;
 extern u8 led_polarity;
@@ -698,6 +708,7 @@ struct wil6210_priv {
 	u8 abft_len;
 	u8 wakeup_trigger;
 	struct wil_suspend_stats suspend_stats;
+	struct wil_debugfs_data dbg_data;
 
 	void *platform_handle;
 	struct wil_platform_ops platform_ops;
@@ -981,6 +992,11 @@ int wil_request_firmware(struct wil6210_priv *wil, const char *name,
 			 bool load);
 bool wil_fw_verify_file_exists(struct wil6210_priv *wil, const char *name);
 
+void wil_pm_runtime_allow(struct wil6210_priv *wil);
+void wil_pm_runtime_forbid(struct wil6210_priv *wil);
+int wil_pm_runtime_get(struct wil6210_priv *wil);
+void wil_pm_runtime_put(struct wil6210_priv *wil);
+
 int wil_can_suspend(struct wil6210_priv *wil, bool is_runtime);
 int wil_suspend(struct wil6210_priv *wil, bool is_runtime);
 int wil_resume(struct wil6210_priv *wil, bool is_runtime);
-- 
1.9.1

[PATCH 06/10] wil6210: add statistics for suspend time

[Maya Erez]

Add statistics for total, min and max suspend time, that
calculates the time the 11ad device was in suspend.
Those statistics will help to estimate the power impact
of d3hot feature.

Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/debugfs.c | 17 +++++++++++++++--
 drivers/net/wireless/ath/wil6210/main.c    |  2 ++
 drivers/net/wireless/ath/wil6210/pm.c      | 20 ++++++++++++++++++--
 drivers/net/wireless/ath/wil6210/wil6210.h |  5 +++++
 4 files changed, 40 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/ath/wil6210/debugfs.c b/drivers/net/wireless/ath/wil6210/debugfs.c
index 8a0e64c..97d79a9 100644
--- a/drivers/net/wireless/ath/wil6210/debugfs.c
+++ b/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -1669,6 +1669,8 @@ static ssize_t wil_write_suspend_stats(struct file *file,
 	struct wil6210_priv *wil = file->private_data;
 
 	memset(&wil->suspend_stats, 0, sizeof(wil->suspend_stats));
+	wil->suspend_stats.min_suspend_time = ULONG_MAX;
+	wil->suspend_stats.collection_start = ktime_get();
 
 	return len;
 }
@@ -1680,18 +1682,27 @@ static ssize_t wil_read_suspend_stats(struct file *file,
 	struct wil6210_priv *wil = file->private_data;
 	static char text[400];
 	int n;
+	unsigned long long stats_collection_time =
+		ktime_to_us(ktime_sub(ktime_get(),
+				      wil->suspend_stats.collection_start));
 
 	n = snprintf(text, sizeof(text),
 		     "Suspend statistics:\n"
 		     "successful suspends:%ld failed suspends:%ld\n"
 		     "successful resumes:%ld failed resumes:%ld\n"
-		     "rejected by host:%ld rejected by device:%ld\n",
+		     "rejected by host:%ld rejected by device:%ld\n"
+		     "total suspend time:%lld min suspend time:%lld\n"
+		     "max suspend time:%lld stats collection time: %lld\n",
 		     wil->suspend_stats.successful_suspends,
 		     wil->suspend_stats.failed_suspends,
 		     wil->suspend_stats.successful_resumes,
 		     wil->suspend_stats.failed_resumes,
 		     wil->suspend_stats.rejected_by_host,
-		     wil->suspend_stats.rejected_by_device);
+		     wil->suspend_stats.rejected_by_device,
+		     wil->suspend_stats.total_suspend_time,
+		     wil->suspend_stats.min_suspend_time,
+		     wil->suspend_stats.max_suspend_time,
+		     stats_collection_time);
 
 	n = min_t(int, n, sizeof(text));
 
@@ -1864,6 +1875,8 @@ int wil6210_debugfs_init(struct wil6210_priv *wil)
 
 	wil6210_debugfs_create_ITR_CNT(wil, dbg);
 
+	wil->suspend_stats.collection_start = ktime_get();
+
 	return 0;
 }
 
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index daf944a..8968c2c 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -578,6 +578,8 @@ int wil_priv_init(struct wil6210_priv *wil)
 
 	wil->wakeup_trigger = WMI_WAKEUP_TRIGGER_UCAST |
 			      WMI_WAKEUP_TRIGGER_BCAST;
+	memset(&wil->suspend_stats, 0, sizeof(wil->suspend_stats));
+	wil->suspend_stats.min_suspend_time = ULONG_MAX;
 
 	return 0;
 
diff --git a/drivers/net/wireless/ath/wil6210/pm.c b/drivers/net/wireless/ath/wil6210/pm.c
index 976c9aa..4a18f8e 100644
--- a/drivers/net/wireless/ath/wil6210/pm.c
+++ b/drivers/net/wireless/ath/wil6210/pm.c
@@ -321,6 +321,9 @@ int wil_suspend(struct wil6210_priv *wil, bool is_runtime)
 	wil_dbg_pm(wil, "suspend: %s => %d\n",
 		   is_runtime ? "runtime" : "system", rc);
 
+	if (!rc)
+		wil->suspend_stats.suspend_start_time = ktime_get();
+
 	return rc;
 }
 
@@ -330,6 +333,7 @@ int wil_resume(struct wil6210_priv *wil, bool is_runtime)
 	struct net_device *ndev = wil_to_ndev(wil);
 	bool keep_radio_on = ndev->flags & IFF_UP &&
 			     wil->keep_radio_on_during_sleep;
+	unsigned long long suspend_time_usec = 0;
 
 	wil_dbg_pm(wil, "resume: %s\n", is_runtime ? "runtime" : "system");
 
@@ -347,9 +351,21 @@ int wil_resume(struct wil6210_priv *wil, bool is_runtime)
 	else
 		rc = wil_resume_radio_off(wil);
 
+	if (rc)
+		goto out;
+
+	suspend_time_usec =
+		ktime_to_us(ktime_sub(ktime_get(),
+				      wil->suspend_stats.suspend_start_time));
+	wil->suspend_stats.total_suspend_time += suspend_time_usec;
+	if (suspend_time_usec < wil->suspend_stats.min_suspend_time)
+		wil->suspend_stats.min_suspend_time = suspend_time_usec;
+	if (suspend_time_usec > wil->suspend_stats.max_suspend_time)
+		wil->suspend_stats.max_suspend_time = suspend_time_usec;
+
 out:
-	wil_dbg_pm(wil, "resume: %s => %d\n",
-		   is_runtime ? "runtime" : "system", rc);
+	wil_dbg_pm(wil, "resume: %s => %d, suspend time %lld usec\n",
+		   is_runtime ? "runtime" : "system", rc, suspend_time_usec);
 	return rc;
 }
 
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index 69103b0..f1488299 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -90,6 +90,11 @@ struct wil_suspend_stats {
 	unsigned long failed_resumes;
 	unsigned long rejected_by_device;
 	unsigned long rejected_by_host;
+	unsigned long long total_suspend_time;
+	unsigned long long min_suspend_time;
+	unsigned long long max_suspend_time;
+	ktime_t collection_start;
+	ktime_t suspend_start_time;
 };
 
 /* Calculate MAC buffer size for the firmware. It includes all overhead,
-- 
1.9.1

[PATCH 07/10] wil6210: notify wiphy on wowlan support

[Maya Erez]

Set wowlan to indicate that 11ad device can wake-up
on any trigger and disconnect.

Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/cfg80211.c | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/drivers/net/wireless/ath/wil6210/cfg80211.c b/drivers/net/wireless/ath/wil6210/cfg80211.c
index c860c0c..61e872c 100644
--- a/drivers/net/wireless/ath/wil6210/cfg80211.c
+++ b/drivers/net/wireless/ath/wil6210/cfg80211.c
@@ -34,6 +34,12 @@
 module_param(scan_timeout, uint, 0644);
 MODULE_PARM_DESC(scan_timeout, " Scan timeout (seconds)");
 
+#ifdef CONFIG_PM
+static struct wiphy_wowlan_support wil_wowlan_support = {
+	.flags = WIPHY_WOWLAN_ANY | WIPHY_WOWLAN_DISCONNECT,
+};
+#endif
+
 #define CHAN60G(_channel, _flags) {				\
 	.band			= NL80211_BAND_60GHZ,		\
 	.center_freq		= 56160 + (2160 * (_channel)),	\
@@ -1819,6 +1825,10 @@ static void wil_wiphy_init(struct wiphy *wiphy)
 
 	wiphy->n_vendor_commands = ARRAY_SIZE(wil_nl80211_vendor_commands);
 	wiphy->vendor_commands = wil_nl80211_vendor_commands;
+
+#ifdef CONFIG_PM
+	wiphy->wowlan = &wil_wowlan_support;
+#endif
 }
 
 struct wireless_dev *wil_cfg80211_init(struct device *dev)
-- 
1.9.1

[PATCH 08/10] wil6210: fix interface-up check

[Maya Erez]

From: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>

While wil_open is executed, any call to netif_running
would return a success. In case there are failures
within wil_open, should not treat the device as if it
is already opened in relevant functions (like FW recovery
and runtime suspend check).

Fix that by checking the device up flag instead.

Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/main.c | 3 ++-
 drivers/net/wireless/ath/wil6210/pm.c   | 4 +++-
 2 files changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index 8968c2c..b1e2814 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -394,10 +394,11 @@ static void wil_fw_error_worker(struct work_struct *work)
 	struct wil6210_priv *wil = container_of(work, struct wil6210_priv,
 						fw_error_worker);
 	struct wireless_dev *wdev = wil->wdev;
+	struct net_device *ndev = wil_to_ndev(wil);
 
 	wil_dbg_misc(wil, "fw error worker\n");
 
-	if (!netif_running(wil_to_ndev(wil))) {
+	if (!(ndev->flags & IFF_UP)) {
 		wil_info(wil, "No recovery - interface is down\n");
 		return;
 	}
diff --git a/drivers/net/wireless/ath/wil6210/pm.c b/drivers/net/wireless/ath/wil6210/pm.c
index 4a18f8e..4f61dc1 100644
--- a/drivers/net/wireless/ath/wil6210/pm.c
+++ b/drivers/net/wireless/ath/wil6210/pm.c
@@ -24,6 +24,7 @@ int wil_can_suspend(struct wil6210_priv *wil, bool is_runtime)
 {
 	int rc = 0;
 	struct wireless_dev *wdev = wil->wdev;
+	struct net_device *ndev = wil_to_ndev(wil);
 	bool wmi_only = test_bit(WMI_FW_CAPABILITY_WMI_ONLY,
 				 wil->fw_capabilities);
 
@@ -35,7 +36,8 @@ int wil_can_suspend(struct wil6210_priv *wil, bool is_runtime)
 		rc = -EPERM;
 		goto out;
 	}
-	if (!netif_running(wil_to_ndev(wil))) {
+
+	if (!(ndev->flags & IFF_UP)) {
 		/* can always sleep when down */
 		wil_dbg_pm(wil, "Interface is down\n");
 		goto out;
-- 
1.9.1

[PATCH 09/10] wil6210: store FW RF calibration result

[Maya Erez]

From: Dedy Lansky <qca_dlansky@qca.qualcomm.com>

Store initial FW RF calibration result in driver. Set this calibration
result back to FW after each FW reset in order to avoid future calibration
procedures.

Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/main.c    | 6 ++++++
 drivers/net/wireless/ath/wil6210/wil6210.h | 6 ++++++
 drivers/net/wireless/ath/wil6210/wmi.c     | 5 +++++
 drivers/net/wireless/ath/wil6210/wmi.h     | 2 ++
 4 files changed, 19 insertions(+)

diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index b1e2814..b89d017 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -1034,6 +1034,12 @@ int wil_reset(struct wil6210_priv *wil, bool load_fw)
 		wil_s(wil, RGF_CAF_ICR + offsetof(struct RGF_ICR, ICR), 0);
 		wil_w(wil, RGF_CAF_ICR + offsetof(struct RGF_ICR, IMV), ~0);
 
+		if (wil->fw_calib_result > 0) {
+			__le32 val = cpu_to_le32(wil->fw_calib_result |
+						 (CALIB_RESULT_SIGNATURE << 8));
+			wil_w(wil, RGF_USER_FW_CALIB_RESULT, (u32 __force)val);
+		}
+
 		wil_release_cpu(wil);
 	}
 
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index f1488299..9ad7b11 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -171,6 +171,10 @@ struct RGF_ICR {
 #define RGF_USER_USER_SCRATCH_PAD	(0x8802bc)
 #define RGF_USER_BL			(0x880A3C) /* Boot Loader */
 #define RGF_USER_FW_REV_ID		(0x880a8c) /* chip revision */
+#define RGF_USER_FW_CALIB_RESULT	(0x880a90) /* b0-7:result
+						    * b8-15:signature
+						    */
+	#define CALIB_RESULT_SIGNATURE	(0x11)
 #define RGF_USER_CLKS_CTL_0		(0x880abc)
 	#define BIT_USER_CLKS_CAR_AHB_SW_SEL	BIT(1) /* ref clk/PLL */
 	#define BIT_USER_CLKS_RST_PWGD	BIT(11) /* reset on "power good" */
@@ -735,6 +739,8 @@ struct wil6210_priv {
 
 	enum wmi_ps_profile_type ps_profile;
 
+	int fw_calib_result;
+
 #ifdef CONFIG_PM
 #ifdef CONFIG_PM_SLEEP
 	struct notifier_block pm_notify;
diff --git a/drivers/net/wireless/ath/wil6210/wmi.c b/drivers/net/wireless/ath/wil6210/wmi.c
index a9487f2..ffdd2fa 100644
--- a/drivers/net/wireless/ath/wil6210/wmi.c
+++ b/drivers/net/wireless/ath/wil6210/wmi.c
@@ -344,6 +344,11 @@ static void wmi_evt_ready(struct wil6210_priv *wil, int id, void *d, int len)
 	strlcpy(wdev->wiphy->fw_version, wil->fw_version,
 		sizeof(wdev->wiphy->fw_version));
 
+	if (len > offsetof(struct wmi_ready_event, rfc_read_calib_result)) {
+		wil_dbg_wmi(wil, "rfc calibration result %d\n",
+			    evt->rfc_read_calib_result);
+		wil->fw_calib_result = evt->rfc_read_calib_result;
+	}
 	wil_set_recovery_state(wil, fw_recovery_idle);
 	set_bit(wil_status_fwready, wil->status);
 	/* let the reset sequence continue */
diff --git a/drivers/net/wireless/ath/wil6210/wmi.h b/drivers/net/wireless/ath/wil6210/wmi.h
index 4e31c2f..1b426d7 100644
--- a/drivers/net/wireless/ath/wil6210/wmi.h
+++ b/drivers/net/wireless/ath/wil6210/wmi.h
@@ -1300,6 +1300,8 @@ struct wmi_ready_event {
 	/* enum wmi_phy_capability */
 	u8 phy_capability;
 	u8 numof_additional_mids;
+	u8 rfc_read_calib_result;
+	u8 reserved[3];
 } __packed;
 
 /* WMI_NOTIFY_REQ_DONE_EVENTID */
-- 
1.9.1

[PATCH 10/10] wil6210: make debugfs compilation optional

[Maya Erez]

From: Gidon Studinski <qca_gidons@qca.qualcomm.com>

Since debugfs is a kernel configuration option, enable the driver to
compile without debugfs.

Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
---
 drivers/net/wireless/ath/wil6210/debugfs.c | 14 ++++++++++----
 drivers/net/wireless/ath/wil6210/main.c    |  1 +
 drivers/net/wireless/ath/wil6210/txrx.c    |  6 +++---
 drivers/net/wireless/ath/wil6210/wil6210.h |  2 +-
 4 files changed, 15 insertions(+), 8 deletions(-)

diff --git a/drivers/net/wireless/ath/wil6210/debugfs.c b/drivers/net/wireless/ath/wil6210/debugfs.c
index 97d79a9..0ef8e0c 100644
--- a/drivers/net/wireless/ath/wil6210/debugfs.c
+++ b/drivers/net/wireless/ath/wil6210/debugfs.c
@@ -14,6 +14,10 @@
  * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
  */
 
+#include "wil6210.h"
+
+#ifdef CONFIG_DEBUG_FS
+
 #include <linux/module.h>
 #include <linux/debugfs.h>
 #include <linux/seq_file.h>
@@ -21,7 +25,6 @@
 #include <linux/rtnetlink.h>
 #include <linux/power_supply.h>
 
-#include "wil6210.h"
 #include "wmi.h"
 #include "txrx.h"
 #include "pmc.h"
@@ -30,7 +33,6 @@
 static u32 mem_addr;
 static u32 dbg_txdesc_index;
 static u32 dbg_vring_index; /* 24+ for Rx, 0..23 for Tx */
-u32 vring_idle_trsh = 16; /* HW fetches up to 16 descriptors at once */
 
 enum dbg_off_type {
 	doff_u32 = 0,
@@ -1815,6 +1817,7 @@ static void wil6210_debugfs_init_isr(struct wil6210_priv *wil,
 	WIL_FIELD(chip_revision, 0444,	doff_u8),
 	WIL_FIELD(abft_len, 0644,		doff_u8),
 	WIL_FIELD(wakeup_trigger, 0644,		doff_u8),
+	WIL_FIELD(vring_idle_trsh, 0644,	doff_u32),
 	{},
 };
 
@@ -1830,8 +1833,6 @@ static void wil6210_debugfs_init_isr(struct wil6210_priv *wil,
 	{"desc_index",	0644, (ulong)&dbg_txdesc_index, doff_u32},
 	{"vring_index",	0644, (ulong)&dbg_vring_index, doff_u32},
 	{"mem_addr",	0644, (ulong)&mem_addr, doff_u32},
-	{"vring_idle_trsh", 0644, (ulong)&vring_idle_trsh,
-	 doff_u32},
 	{"led_polarity", 0644, (ulong)&led_polarity, doff_u8},
 	{},
 };
@@ -1892,3 +1893,8 @@ void wil6210_debugfs_remove(struct wil6210_priv *wil)
 	 */
 	wil_pmc_free(wil, false);
 }
+
+#else /* !CONFIG_DEBUG_FS */
+int wil6210_debugfs_init(struct wil6210_priv *wil) { return 0; }
+void wil6210_debugfs_remove(struct wil6210_priv *wil) {}
+#endif
diff --git a/drivers/net/wireless/ath/wil6210/main.c b/drivers/net/wireless/ath/wil6210/main.c
index b89d017..e2ea490 100644
--- a/drivers/net/wireless/ath/wil6210/main.c
+++ b/drivers/net/wireless/ath/wil6210/main.c
@@ -581,6 +581,7 @@ int wil_priv_init(struct wil6210_priv *wil)
 			      WMI_WAKEUP_TRIGGER_BCAST;
 	memset(&wil->suspend_stats, 0, sizeof(wil->suspend_stats));
 	wil->suspend_stats.min_suspend_time = ULONG_MAX;
+	wil->vring_idle_trsh = 16;
 
 	return 0;
 
diff --git a/drivers/net/wireless/ath/wil6210/txrx.c b/drivers/net/wireless/ath/wil6210/txrx.c
index ec57bcc..389c718 100644
--- a/drivers/net/wireless/ath/wil6210/txrx.c
+++ b/drivers/net/wireless/ath/wil6210/txrx.c
@@ -1666,7 +1666,7 @@ static int __wil_tx_vring_tso(struct wil6210_priv *wil, struct vring *vring,
 
 	/* performance monitoring */
 	used = wil_vring_used_tx(vring);
-	if (wil_val_in_range(vring_idle_trsh,
+	if (wil_val_in_range(wil->vring_idle_trsh,
 			     used, used + descs_used)) {
 		txdata->idle += get_cycles() - txdata->last_idle;
 		wil_dbg_txrx(wil,  "Ring[%2d] not idle %d -> %d\n",
@@ -1813,7 +1813,7 @@ static int __wil_tx_vring(struct wil6210_priv *wil, struct vring *vring,
 
 	/* performance monitoring */
 	used = wil_vring_used_tx(vring);
-	if (wil_val_in_range(vring_idle_trsh,
+	if (wil_val_in_range(wil->vring_idle_trsh,
 			     used, used + nr_frags + 1)) {
 		txdata->idle += get_cycles() - txdata->last_idle;
 		wil_dbg_txrx(wil,  "Ring[%2d] not idle %d -> %d\n",
@@ -2175,7 +2175,7 @@ int wil_tx_complete(struct wil6210_priv *wil, int ringid)
 
 	/* performance monitoring */
 	used_new = wil_vring_used_tx(vring);
-	if (wil_val_in_range(vring_idle_trsh,
+	if (wil_val_in_range(wil->vring_idle_trsh,
 			     used_new, used_before_complete)) {
 		wil_dbg_txrx(wil, "Ring[%2d] idle %d -> %d\n",
 			     ringid, used_before_complete, used_new);
diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h
index 9ad7b11..bdfcd72 100644
--- a/drivers/net/wireless/ath/wil6210/wil6210.h
+++ b/drivers/net/wireless/ath/wil6210/wil6210.h
@@ -30,7 +30,6 @@
 extern unsigned int mtu_max;
 extern unsigned short rx_ring_overflow_thrsh;
 extern int agg_wsize;
-extern u32 vring_idle_trsh;
 extern bool rx_align_2;
 extern bool rx_large_buf;
 extern bool debug_fw;
@@ -703,6 +702,7 @@ struct wil6210_priv {
 	u8 vring2cid_tid[WIL6210_MAX_TX_RINGS][2]; /* [0] - CID, [1] - TID */
 	struct wil_sta_info sta[WIL6210_MAX_CID];
 	int bcast_vring;
+	u32 vring_idle_trsh; /* HW fetches up to 16 descriptors at once  */
 	bool use_extended_dma_addr; /* indicates whether we are using 48 bits */
 	/* scan */
 	struct cfg80211_scan_request *scan_request;
-- 
1.9.1