From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from wolverine01.qualcomm.com ([199.106.114.254]:25940 "EHLO wolverine01.qualcomm.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751085AbeAUJU6 (ORCPT ); Sun, 21 Jan 2018 04:20:58 -0500 From: Maya Erez To: Kalle Valo Cc: Maya Erez , linux-wireless@vger.kernel.org, wil6210@qti.qualcomm.com, Dedy Lansky Subject: [PATCH v2 3/8] wil6210: add support for Talyn AHB address map Date: Sun, 21 Jan 2018 11:14:38 +0200 Message-Id: <1516526083-31389-4-git-send-email-merez@codeaurora.org> (sfid-20180121_102105_100493_F63DE657) In-Reply-To: <1516526083-31389-1-git-send-email-merez@codeaurora.org> References: <1516526083-31389-1-git-send-email-merez@codeaurora.org> Sender: linux-wireless-owner@vger.kernel.org List-ID: Talyn memory has changed, areas were increased and shifted to new locations. Use the appropriate address map according to the device JTAG ID. Signed-off-by: Dedy Lansky Signed-off-by: Maya Erez --- drivers/net/wireless/ath/wil6210/interrupt.c | 6 ++- drivers/net/wireless/ath/wil6210/pcie_bus.c | 18 +++++++- drivers/net/wireless/ath/wil6210/wil6210.h | 21 +++++++-- drivers/net/wireless/ath/wil6210/wmi.c | 64 ++++++++++++++++++++++++---- 4 files changed, 92 insertions(+), 17 deletions(-) diff --git a/drivers/net/wireless/ath/wil6210/interrupt.c b/drivers/net/wireless/ath/wil6210/interrupt.c index dcf87a7..1835187 100644 --- a/drivers/net/wireless/ath/wil6210/interrupt.c +++ b/drivers/net/wireless/ath/wil6210/interrupt.c @@ -1,5 +1,6 @@ /* * Copyright (c) 2012-2017 Qualcomm Atheros, Inc. + * Copyright (c) 2018, The Linux Foundation. All rights reserved. * * Permission to use, copy, modify, and/or distribute this software for any * purpose with or without fee is hereby granted, provided that the above @@ -395,8 +396,9 @@ static irqreturn_t wil6210_irq_misc(int irq, void *cookie) wil6210_mask_irq_misc(wil, false); if (isr & ISR_MISC_FW_ERROR) { - u32 fw_assert_code = wil_r(wil, RGF_FW_ASSERT_CODE); - u32 ucode_assert_code = wil_r(wil, RGF_UCODE_ASSERT_CODE); + u32 fw_assert_code = wil_r(wil, wil->rgf_fw_assert_code_addr); + u32 ucode_assert_code = + wil_r(wil, wil->rgf_ucode_assert_code_addr); wil_err(wil, "Firmware error detected, assert codes FW 0x%08x, UCODE 0x%08x\n", diff --git a/drivers/net/wireless/ath/wil6210/pcie_bus.c b/drivers/net/wireless/ath/wil6210/pcie_bus.c index 2b3b1f7..6b153fe 100644 --- a/drivers/net/wireless/ath/wil6210/pcie_bus.c +++ b/drivers/net/wireless/ath/wil6210/pcie_bus.c @@ -36,7 +36,7 @@ static int wil6210_pm_notify(struct notifier_block *notify_block, unsigned long mode, void *unused); static -void wil_set_capabilities(struct wil6210_priv *wil) +int wil_set_capabilities(struct wil6210_priv *wil) { const char *wil_fw_name; u32 jtag_id = wil_r(wil, RGF_USER_JTAG_DEV_ID); @@ -72,16 +72,24 @@ void wil_set_capabilities(struct wil6210_priv *wil) wil->hw_version = HW_VER_UNKNOWN; break; } + memcpy(fw_mapping, sparrow_fw_mapping, + sizeof(sparrow_fw_mapping)); + wil->rgf_fw_assert_code_addr = SPARROW_RGF_FW_ASSERT_CODE; + wil->rgf_ucode_assert_code_addr = SPARROW_RGF_UCODE_ASSERT_CODE; break; case JTAG_DEV_ID_TALYN: wil->hw_name = "Talyn"; wil->hw_version = HW_VER_TALYN; + memcpy(fw_mapping, talyn_fw_mapping, sizeof(talyn_fw_mapping)); + wil->rgf_fw_assert_code_addr = TALYN_RGF_FW_ASSERT_CODE; + wil->rgf_ucode_assert_code_addr = TALYN_RGF_UCODE_ASSERT_CODE; break; default: wil_err(wil, "Unknown board hardware, chip_id 0x%08x, chip_revision 0x%08x\n", jtag_id, chip_revision); wil->hw_name = "Unknown"; wil->hw_version = HW_VER_UNKNOWN; + return -EINVAL; } wil_info(wil, "Board hardware is %s\n", wil->hw_name); @@ -97,6 +105,8 @@ void wil_set_capabilities(struct wil6210_priv *wil) /* extract FW capabilities from file without loading the FW */ wil_request_firmware(wil, wil->wil_fw_name, false); wil_refresh_fw_capabilities(wil); + + return 0; } void wil_disable_irq(struct wil6210_priv *wil) @@ -307,7 +317,11 @@ static int wil_pcie_probe(struct pci_dev *pdev, const struct pci_device_id *id) /* rollback to err_iounmap */ wil_info(wil, "CSR at %pR -> 0x%p\n", &pdev->resource[0], wil->csr); - wil_set_capabilities(wil); + rc = wil_set_capabilities(wil); + if (rc) { + wil_err(wil, "wil_set_capabilities failed, rc %d\n", rc); + goto err_iounmap; + } wil6210_clear_irq(wil); /* FW should raise IRQ when ready */ diff --git a/drivers/net/wireless/ath/wil6210/wil6210.h b/drivers/net/wireless/ath/wil6210/wil6210.h index a59a553..79356bb 100644 --- a/drivers/net/wireless/ath/wil6210/wil6210.h +++ b/drivers/net/wireless/ath/wil6210/wil6210.h @@ -295,8 +295,12 @@ struct RGF_ICR { #define REVISION_ID_SPARROW_D0 (0x3) /* crash codes for FW/Ucode stored here */ -#define RGF_FW_ASSERT_CODE (0x91f020) -#define RGF_UCODE_ASSERT_CODE (0x91f028) + +/* ASSERT RGFs */ +#define SPARROW_RGF_FW_ASSERT_CODE (0x91f020) +#define SPARROW_RGF_UCODE_ASSERT_CODE (0x91f028) +#define TALYN_RGF_FW_ASSERT_CODE (0xa37020) +#define TALYN_RGF_UCODE_ASSERT_CODE (0xa37028) enum { HW_VER_UNKNOWN, @@ -318,6 +322,10 @@ enum { #define WIL_DATA_COMPLETION_TO_MS 200 /* Hardware definitions end */ +#define SPARROW_FW_MAPPING_TABLE_SIZE 10 +#define TALYN_FW_MAPPING_TABLE_SIZE 13 +#define MAX_FW_MAPPING_TABLE_SIZE 13 + struct fw_map { u32 from; /* linker address - from, inclusive */ u32 to; /* linker address - to, exclusive */ @@ -327,7 +335,9 @@ struct fw_map { }; /* array size should be in sync with actual definition in the wmi.c */ -extern const struct fw_map fw_mapping[10]; +extern const struct fw_map sparrow_fw_mapping[SPARROW_FW_MAPPING_TABLE_SIZE]; +extern const struct fw_map talyn_fw_mapping[TALYN_FW_MAPPING_TABLE_SIZE]; +extern struct fw_map fw_mapping[MAX_FW_MAPPING_TABLE_SIZE]; /** * mk_cidxtid - construct @cidxtid field @@ -723,7 +733,7 @@ struct wil6210_priv { atomic_t isr_count_rx, isr_count_tx; /* debugfs */ struct dentry *debug; - struct wil_blob_wrapper blobs[ARRAY_SIZE(fw_mapping)]; + struct wil_blob_wrapper blobs[MAX_FW_MAPPING_TABLE_SIZE]; u8 discovery_mode; u8 abft_len; u8 wakeup_trigger; @@ -758,6 +768,9 @@ struct wil6210_priv { bool suspend_resp_comp; u32 bus_request_kbps; u32 bus_request_kbps_pre_suspend; + + u32 rgf_fw_assert_code_addr; + u32 rgf_ucode_assert_code_addr; }; #define wil_to_wiphy(i) (i->wdev->wiphy) diff --git a/drivers/net/wireless/ath/wil6210/wmi.c b/drivers/net/wireless/ath/wil6210/wmi.c index 2ab71bb..69da3c2 100644 --- a/drivers/net/wireless/ath/wil6210/wmi.c +++ b/drivers/net/wireless/ath/wil6210/wmi.c @@ -1,5 +1,6 @@ /* * Copyright (c) 2012-2017 Qualcomm Atheros, Inc. + * Copyright (c) 2018, The Linux Foundation. All rights reserved. * * Permission to use, copy, modify, and/or distribute this software for any * purpose with or without fee is hereby granted, provided that the above @@ -70,23 +71,23 @@ * On the PCI bus, there is one BAR (BAR0) of 2Mb size, exposing * AHB addresses starting from 0x880000 * - * Internally, firmware uses addresses that allows faster access but + * Internally, firmware uses addresses that allow faster access but * are invisible from the host. To read from these addresses, alternative * AHB address must be used. - * - * Memory mapping - * Linker address PCI/Host address - * 0x880000 .. 0xa80000 2Mb BAR0 - * 0x800000 .. 0x807000 0x900000 .. 0x907000 28k DCCM - * 0x840000 .. 0x857000 0x908000 .. 0x91f000 92k PERIPH */ /** - * @fw_mapping provides memory remapping table + * @sparrow_fw_mapping provides memory remapping table for sparrow * * array size should be in sync with the declaration in the wil6210.h + * + * Sparrow memory mapping: + * Linker address PCI/Host address + * 0x880000 .. 0xa80000 2Mb BAR0 + * 0x800000 .. 0x808000 0x900000 .. 0x908000 32k DCCM + * 0x840000 .. 0x860000 0x908000 .. 0x928000 128k PERIPH */ -const struct fw_map fw_mapping[] = { +const struct fw_map sparrow_fw_mapping[] = { /* FW code RAM 256k */ {0x000000, 0x040000, 0x8c0000, "fw_code", true}, /* FW data RAM 32k */ @@ -112,6 +113,51 @@ {0x800000, 0x804000, 0x940000, "uc_data", false}, }; +/** + * @talyn_fw_mapping provides memory remapping table for Talyn + * + * array size should be in sync with the declaration in the wil6210.h + * + * Talyn memory mapping: + * Linker address PCI/Host address + * 0x880000 .. 0xc80000 4Mb BAR0 + * 0x800000 .. 0x820000 0xa00000 .. 0xa20000 128k DCCM + * 0x840000 .. 0x858000 0xa20000 .. 0xa38000 96k PERIPH + */ +const struct fw_map talyn_fw_mapping[] = { + /* FW code RAM 1M */ + {0x000000, 0x100000, 0x900000, "fw_code", true}, + /* FW data RAM 128k */ + {0x800000, 0x820000, 0xa00000, "fw_data", true}, + /* periph. data RAM 96k */ + {0x840000, 0x858000, 0xa20000, "fw_peri", true}, + /* various RGF 40k */ + {0x880000, 0x88a000, 0x880000, "rgf", true}, + /* AGC table 4k */ + {0x88a000, 0x88b000, 0x88a000, "AGC_tbl", true}, + /* Pcie_ext_rgf 4k */ + {0x88b000, 0x88c000, 0x88b000, "rgf_ext", true}, + /* mac_ext_rgf 1344b */ + {0x88c000, 0x88c540, 0x88c000, "mac_rgf_ext", true}, + /* ext USER RGF 4k */ + {0x88d000, 0x88e000, 0x88d000, "ext_user_rgf", true}, + /* OTP 4k */ + {0x8a0000, 0x8a1000, 0x8a0000, "otp", true}, + /* DMA EXT RGF 64k */ + {0x8b0000, 0x8c0000, 0x8b0000, "dma_ext_rgf", true}, + /* upper area 1536k */ + {0x900000, 0xa80000, 0x900000, "upper", true}, + /* UCODE areas - accessible by debugfs blobs but not by + * wmi_addr_remap. UCODE areas MUST be added AFTER FW areas! + */ + /* ucode code RAM 256k */ + {0x000000, 0x040000, 0xa38000, "uc_code", false}, + /* ucode data RAM 32k */ + {0x800000, 0x808000, 0xa78000, "uc_data", false}, +}; + +struct fw_map fw_mapping[MAX_FW_MAPPING_TABLE_SIZE]; + struct blink_on_off_time led_blink_time[] = { {WIL_LED_BLINK_ON_SLOW_MS, WIL_LED_BLINK_OFF_SLOW_MS}, {WIL_LED_BLINK_ON_MED_MS, WIL_LED_BLINK_OFF_MED_MS}, -- 1.9.1