From: Maharaja Kennadyrajan <mkenna@codeaurora.org>
To: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org,
Maharaja Kennadyrajan <mkenna@codeaurora.org>
Subject: [PATCH] ath10k: add debugfs file warm_hw_reset
Date: Wed, 18 Jul 2018 19:04:20 +0530 [thread overview]
Message-ID: <1531920860-3236-1-git-send-email-mkenna@codeaurora.org> (raw)
Debugfs support to do hardware warm reset with WMI command
WMI_PDEV_PARAM_PDEV_RESET for 10.4 and 10.2.4(if wmi
service is enabled in the firmware for backward compatibility).
This change is purely for debugging purpose when hardware hangs/mutes.
This hardware reset won't affect the connectivity but there will be small
pause in data traffic. Here we are doing BB/MAC level reset and hence
whenever the BB/MAC watchdog is triggered, it does a hardware_chip_reset.
So the target will be in the active state.
Below command used to warm reset the hardware.
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/warm_hw_reset
Tested in QCA988X with firmware ver 10.2.4.70.45
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
---
drivers/net/wireless/ath/ath10k/debug.c | 49 +++++++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath10k/wmi.c | 2 +-
drivers/net/wireless/ath/ath10k/wmi.h | 16 ++++++++++-
3 files changed, 65 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/debug.c b/drivers/net/wireless/ath/ath10k/debug.c
index 4926722..0baaad9 100644
--- a/drivers/net/wireless/ath/ath10k/debug.c
+++ b/drivers/net/wireless/ath/ath10k/debug.c
@@ -2297,6 +2297,52 @@ static ssize_t ath10k_tpc_stats_final_read(struct file *file,
.llseek = default_llseek,
};
+static ssize_t ath10k_write_warm_hw_reset(struct file *file,
+ const char __user *user_buf,
+ size_t count, loff_t *ppos)
+{
+ struct ath10k *ar = file->private_data;
+ int ret;
+ bool val;
+
+ if (kstrtobool_from_user(user_buf, count, &val))
+ return -EFAULT;
+
+ if (!val)
+ return -EINVAL;
+
+ mutex_lock(&ar->conf_mutex);
+
+ if (ar->state != ATH10K_STATE_ON) {
+ ret = -ENETDOWN;
+ goto exit;
+ }
+
+ if (!(test_bit(WMI_SERVICE_RESET_CHIP, ar->wmi.svc_map)))
+ ath10k_warn(ar, "wmi service for reset chip is not available\n");
+
+ ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->pdev_reset,
+ WMI_RST_MODE_WARM_RESET);
+
+ if (ret) {
+ ath10k_warn(ar, "failed to enable warm hw reset: %d\n", ret);
+ goto exit;
+ }
+
+ ret = count;
+
+exit:
+ mutex_unlock(&ar->conf_mutex);
+ return ret;
+}
+
+static const struct file_operations fops_warm_hw_reset = {
+ .write = ath10k_write_warm_hw_reset,
+ .open = simple_open,
+ .owner = THIS_MODULE,
+ .llseek = default_llseek,
+};
+
int ath10k_debug_create(struct ath10k *ar)
{
ar->debug.cal_data = vzalloc(ATH10K_DEBUG_CAL_DATA_LEN);
@@ -2425,6 +2471,9 @@ int ath10k_debug_register(struct ath10k *ar)
ar->debug.debugfs_phy, ar,
&fops_tpc_stats_final);
+ debugfs_create_file("warm_hw_reset", 0600, ar->debug.debugfs_phy, ar,
+ &fops_warm_hw_reset);
+
return 0;
}
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 877249a..2fb972e 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -1333,7 +1333,7 @@
.enable_per_tid_ampdu = WMI_PDEV_PARAM_UNSUPPORTED,
.cca_threshold = WMI_PDEV_PARAM_UNSUPPORTED,
.rts_fixed_rate = WMI_PDEV_PARAM_UNSUPPORTED,
- .pdev_reset = WMI_PDEV_PARAM_UNSUPPORTED,
+ .pdev_reset = WMI_10X_PDEV_PARAM_PDEV_RESET,
.wapi_mbssid_offset = WMI_PDEV_PARAM_UNSUPPORTED,
.arp_srcaddr = WMI_PDEV_PARAM_UNSUPPORTED,
.arp_dstaddr = WMI_PDEV_PARAM_UNSUPPORTED,
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index d68afb6..e24d869 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -462,6 +462,7 @@ static inline char *wmi_service_name(int service_id)
SVCSTR(WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS);
SVCSTR(WMI_SERVICE_HOST_DFS_CHECK_SUPPORT);
SVCSTR(WMI_SERVICE_TPC_STATS_FINAL);
+ SVCSTR(WMI_SERVICE_RESET_CHIP);
default:
return NULL;
}
@@ -3934,7 +3935,11 @@ enum wmi_10x_pdev_param {
WMI_10X_PDEV_PARAM_REMOVE_MCAST2UCAST_BUFFER,
WMI_10X_PDEV_PARAM_PEER_STA_PS_STATECHG_ENABLE,
WMI_10X_PDEV_PARAM_RTS_FIXED_RATE,
- WMI_10X_PDEV_PARAM_CAL_PERIOD
+ WMI_10X_PDEV_PARAM_CAL_PERIOD,
+ WMI_10X_PDEV_PARAM_ATF_STRICT_SCH,
+ WMI_10X_PDEV_PARAM_ATF_SCHED_DURATION,
+ WMI_10X_PDEV_PARAM_SET_PROMISC_MODE_CMDID,
+ WMI_10X_PDEV_PARAM_PDEV_RESET
};
enum wmi_10_4_pdev_param {
@@ -6501,6 +6506,15 @@ struct wmi_force_fw_hang_cmd {
__le32 delay_ms;
} __packed;
+enum wmi_pdev_reset_mode_type {
+ WMI_RST_MODE_TX_FLUSH = 1,
+ WMI_RST_MODE_WARM_RESET,
+ WMI_RST_MODE_COLD_RESET,
+ WMI_RST_MODE_WARM_RESET_RESTORE_CAL,
+ WMI_RST_MODE_COLD_RESET_RESTORE_CAL,
+ WMI_RST_MODE_MAX,
+};
+
enum ath10k_dbglog_level {
ATH10K_DBGLOG_LEVEL_VERBOSE = 0,
ATH10K_DBGLOG_LEVEL_INFO = 1,
--
1.9.1
next reply other threads:[~2018-07-18 14:12 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-18 13:34 Maharaja Kennadyrajan [this message]
2018-07-30 18:00 ` [PATCH] ath10k: add debugfs file warm_hw_reset Kalle Valo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1531920860-3236-1-git-send-email-mkenna@codeaurora.org \
--to=mkenna@codeaurora.org \
--cc=ath10k@lists.infradead.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).