From: Maya Erez <merez@codeaurora.org>
To: Kalle Valo <kvalo@codeaurora.org>
Cc: Maya Erez <merez@codeaurora.org>,
linux-wireless@vger.kernel.org, wil6210@qti.qualcomm.com
Subject: [PATCH 11/16] wil6210: fix L2 RX status handling
Date: Wed, 31 Oct 2018 10:52:19 +0200 [thread overview]
Message-ID: <1540975944-30576-12-git-send-email-merez@codeaurora.org> (raw)
In-Reply-To: <1540975944-30576-1-git-send-email-merez@codeaurora.org>
L2 RX status errors should not be treated as a bitmap and the actual
error values should be checked.
Print L2 errors as wil_err_ratelimited for easier debugging
when such errors occurs.
Signed-off-by: Maya Erez <merez@codeaurora.org>
---
drivers/net/wireless/ath/wil6210/txrx_edma.c | 23 ++++++++++++-----------
1 file changed, 12 insertions(+), 11 deletions(-)
diff --git a/drivers/net/wireless/ath/wil6210/txrx_edma.c b/drivers/net/wireless/ath/wil6210/txrx_edma.c
index fe758f2..c8490e7 100644
--- a/drivers/net/wireless/ath/wil6210/txrx_edma.c
+++ b/drivers/net/wireless/ath/wil6210/txrx_edma.c
@@ -839,23 +839,24 @@ static int wil_rx_error_check_edma(struct wil6210_priv *wil,
wil_dbg_txrx(wil, "L2 RX error, l2_rx_status=0x%x\n",
l2_rx_status);
/* Due to HW issue, KEY error will trigger a MIC error */
- if (l2_rx_status & WIL_RX_EDMA_ERROR_MIC) {
- wil_dbg_txrx(wil,
- "L2 MIC/KEY error, dropping packet\n");
+ if (l2_rx_status == WIL_RX_EDMA_ERROR_MIC) {
+ wil_err_ratelimited(wil,
+ "L2 MIC/KEY error, dropping packet\n");
stats->rx_mic_error++;
}
- if (l2_rx_status & WIL_RX_EDMA_ERROR_KEY) {
- wil_dbg_txrx(wil, "L2 KEY error, dropping packet\n");
+ if (l2_rx_status == WIL_RX_EDMA_ERROR_KEY) {
+ wil_err_ratelimited(wil,
+ "L2 KEY error, dropping packet\n");
stats->rx_key_error++;
}
- if (l2_rx_status & WIL_RX_EDMA_ERROR_REPLAY) {
- wil_dbg_txrx(wil,
- "L2 REPLAY error, dropping packet\n");
+ if (l2_rx_status == WIL_RX_EDMA_ERROR_REPLAY) {
+ wil_err_ratelimited(wil,
+ "L2 REPLAY error, dropping packet\n");
stats->rx_replay++;
}
- if (l2_rx_status & WIL_RX_EDMA_ERROR_AMSDU) {
- wil_dbg_txrx(wil,
- "L2 AMSDU error, dropping packet\n");
+ if (l2_rx_status == WIL_RX_EDMA_ERROR_AMSDU) {
+ wil_err_ratelimited(wil,
+ "L2 AMSDU error, dropping packet\n");
stats->rx_amsdu_error++;
}
return -EFAULT;
--
1.9.1
next prev parent reply other threads:[~2018-10-31 8:58 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-31 8:52 [PATCH 00/16] wil6210 patches Maya Erez
2018-10-31 8:52 ` [PATCH 01/16] wil6210: remove fake support for RXHASH Maya Erez
2018-11-06 16:05 ` Kalle Valo
2018-10-31 8:52 ` [PATCH 02/16] wil6210: fix reset flow for Talyn-mb Maya Erez
2018-10-31 8:52 ` [PATCH 03/16] wil6210: increase RX rings and RX buff array size Maya Erez
2018-10-31 8:52 ` [PATCH 04/16] wil6210: make sure Rx ring sizes are correlated Maya Erez
2018-10-31 8:52 ` [PATCH 05/16] wil6210: add recovery for FW error while in AP mode Maya Erez
2018-10-31 8:52 ` [PATCH 06/16] wil6210: fix memory leak in wil_find_tx_bcast_2 Maya Erez
2018-10-31 8:52 ` [PATCH 07/16] wil6210: refactor disconnect flow Maya Erez
2018-11-06 10:30 ` Kalle Valo
2018-11-06 11:52 ` merez
2018-11-06 12:28 ` Kalle Valo
2018-11-06 12:38 ` merez
2018-11-06 12:40 ` Kalle Valo
2018-10-31 8:52 ` [PATCH 08/16] wil6210: notify cqm packet loss on disable_ap_sme Maya Erez
2018-10-31 8:52 ` [PATCH 09/16] wil6210: add general initialization/size checks Maya Erez
2018-10-31 8:52 ` [PATCH 10/16] wil6210: fix debugfs memory access alignment Maya Erez
2018-10-31 8:52 ` Maya Erez [this message]
2018-10-31 8:52 ` [PATCH 12/16] wil6210: fix RGF_CAF_ICR address for Talyn-MB Maya Erez
2018-10-31 8:52 ` [PATCH 13/16] wil6210: ignore HALP ICR if already handled Maya Erez
2018-11-06 10:04 ` Kalle Valo
2018-11-06 12:24 ` merez
2018-10-31 8:52 ` [PATCH 14/16] wil6210: remove unnecessary alignment code from rx flow Maya Erez
2018-10-31 8:52 ` [PATCH 15/16] wil6210: fix freeing of rx buffers in EDMA mode Maya Erez
2018-10-31 8:52 ` [PATCH 16/16] wil6210: fix locking in wmi_call Maya Erez
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1540975944-30576-12-git-send-email-merez@codeaurora.org \
--to=merez@codeaurora.org \
--cc=kvalo@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
--cc=wil6210@qti.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).