From: <Ajay.Kathat@microchip.com>
To: <linux-wireless@vger.kernel.org>
Cc: <gregkh@linuxfoundation.org>, <kvalo@codeaurora.org>,
<johannes@sipsolutions.net>, <Adham.Abozaeid@microchip.com>,
<Venkateswara.Kaja@microchip.com>, <Nicolas.Ferre@microchip.com>,
<Claudiu.Beznea@microchip.com>, <Ajay.Kathat@microchip.com>
Subject: [PATCH 06/16] wilc1000: add wilc_wfi_netdevice.h
Date: Sat, 9 Feb 2019 07:12:27 +0000 [thread overview]
Message-ID: <1549696298-9795-7-git-send-email-ajay.kathat@microchip.com> (raw)
In-Reply-To: <1549696298-9795-1-git-send-email-ajay.kathat@microchip.com>
From: Ajay Singh <ajay.kathat@microchip.com>
Moved '/driver/staging/wilc1000/wilc_wfi_netdevice.h' to
'drivers/net/wireless/microchip/wilc1000/'.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
---
.../microchip/wilc1000/wilc_wfi_netdevice.h | 292 +++++++++++++++++++++
1 file changed, 292 insertions(+)
create mode 100644 drivers/net/wireless/microchip/wilc1000/wilc_wfi_netdevice.h
diff --git a/drivers/net/wireless/microchip/wilc1000/wilc_wfi_netdevice.h b/drivers/net/wireless/microchip/wilc1000/wilc_wfi_netdevice.h
new file mode 100644
index 0000000..df00762
--- /dev/null
+++ b/drivers/net/wireless/microchip/wilc1000/wilc_wfi_netdevice.h
@@ -0,0 +1,292 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2012 - 2018 Microchip Technology Inc., and its subsidiaries.
+ * All rights reserved.
+ */
+
+#ifndef WILC_WFI_NETDEVICE
+#define WILC_WFI_NETDEVICE
+
+#include <linux/tcp.h>
+#include <linux/ieee80211.h>
+#include <net/cfg80211.h>
+#include <net/ieee80211_radiotap.h>
+#include <linux/if_arp.h>
+#include <linux/gpio/consumer.h>
+
+#include "host_interface.h"
+#include "wilc_wlan.h"
+#include "wilc_wlan_cfg.h"
+
+#define FLOW_CONTROL_LOWER_THRESHOLD 128
+#define FLOW_CONTROL_UPPER_THRESHOLD 256
+
+#define WILC_MAX_NUM_PMKIDS 16
+#define PMKID_FOUND 1
+#define NUM_STA_ASSOCIATED 8
+
+#define NUM_REG_FRAME 2
+
+#define TCP_ACK_FILTER_LINK_SPEED_THRESH 54
+#define DEFAULT_LINK_SPEED 72
+
+#define GET_PKT_OFFSET(a) (((a) >> 22) & 0x1ff)
+
+struct wilc_wfi_stats {
+ unsigned long rx_packets;
+ unsigned long tx_packets;
+ unsigned long rx_bytes;
+ unsigned long tx_bytes;
+ u64 rx_time;
+ u64 tx_time;
+
+};
+
+struct wilc_wfi_key {
+ u8 *key;
+ u8 *seq;
+ int key_len;
+ int seq_len;
+ u32 cipher;
+};
+
+struct wilc_wfi_wep_key {
+ u8 *key;
+ u8 key_len;
+ u8 key_idx;
+};
+
+struct sta_info {
+ u8 sta_associated_bss[WILC_MAX_NUM_STA][ETH_ALEN];
+};
+
+/*Parameters needed for host interface for remaining on channel*/
+struct wilc_wfi_p2p_listen_params {
+ struct ieee80211_channel *listen_ch;
+ u32 listen_duration;
+ u64 listen_cookie;
+};
+
+struct wilc_p2p_var {
+ u8 local_random;
+ u8 recv_random;
+ bool is_wilc_ie;
+};
+
+static const u32 wilc_cipher_suites[] = {
+ WLAN_CIPHER_SUITE_WEP40,
+ WLAN_CIPHER_SUITE_WEP104,
+ WLAN_CIPHER_SUITE_TKIP,
+ WLAN_CIPHER_SUITE_CCMP,
+ WLAN_CIPHER_SUITE_AES_CMAC
+};
+
+#define CHAN2G(_channel, _freq, _flags) { \
+ .band = NL80211_BAND_2GHZ, \
+ .center_freq = (_freq), \
+ .hw_value = (_channel), \
+ .flags = (_flags), \
+ .max_antenna_gain = 0, \
+ .max_power = 30, \
+}
+
+static const struct ieee80211_channel wilc_2ghz_channels[] = {
+ CHAN2G(1, 2412, 0),
+ CHAN2G(2, 2417, 0),
+ CHAN2G(3, 2422, 0),
+ CHAN2G(4, 2427, 0),
+ CHAN2G(5, 2432, 0),
+ CHAN2G(6, 2437, 0),
+ CHAN2G(7, 2442, 0),
+ CHAN2G(8, 2447, 0),
+ CHAN2G(9, 2452, 0),
+ CHAN2G(10, 2457, 0),
+ CHAN2G(11, 2462, 0),
+ CHAN2G(12, 2467, 0),
+ CHAN2G(13, 2472, 0),
+ CHAN2G(14, 2484, 0)
+};
+
+#define RATETAB_ENT(_rate, _hw_value, _flags) { \
+ .bitrate = (_rate), \
+ .hw_value = (_hw_value), \
+ .flags = (_flags), \
+}
+
+static struct ieee80211_rate wilc_bitrates[] = {
+ RATETAB_ENT(10, 0, 0),
+ RATETAB_ENT(20, 1, 0),
+ RATETAB_ENT(55, 2, 0),
+ RATETAB_ENT(110, 3, 0),
+ RATETAB_ENT(60, 9, 0),
+ RATETAB_ENT(90, 6, 0),
+ RATETAB_ENT(120, 7, 0),
+ RATETAB_ENT(180, 8, 0),
+ RATETAB_ENT(240, 9, 0),
+ RATETAB_ENT(360, 10, 0),
+ RATETAB_ENT(480, 11, 0),
+ RATETAB_ENT(540, 12, 0)
+};
+
+struct wilc_priv {
+ struct wireless_dev *wdev;
+ struct cfg80211_scan_request *scan_req;
+
+ struct wilc_wfi_p2p_listen_params remain_on_ch_params;
+ u64 tx_cookie;
+
+ bool cfg_scanning;
+
+ u8 associated_bss[ETH_ALEN];
+ struct sta_info assoc_stainfo;
+ struct sk_buff *skb;
+ struct net_device *dev;
+ struct host_if_drv *hif_drv;
+ struct wilc_pmkid_attr pmkid_list;
+ u8 wep_key[4][WLAN_KEY_LEN_WEP104];
+ u8 wep_key_len[4];
+ /* The real interface that the monitor is on */
+ struct net_device *real_ndev;
+ struct wilc_wfi_key *wilc_gtk[WILC_MAX_NUM_STA];
+ struct wilc_wfi_key *wilc_ptk[WILC_MAX_NUM_STA];
+ u8 wilc_groupkey;
+ /* mutexes */
+ struct mutex scan_req_lock;
+ bool p2p_listen_state;
+ int scanned_cnt;
+ struct wilc_p2p_var p2p;
+
+ struct ieee80211_channel channels[ARRAY_SIZE(wilc_2ghz_channels)];
+ struct ieee80211_rate bitrates[ARRAY_SIZE(wilc_bitrates)];
+ struct ieee80211_supported_band band;
+ u32 cipher_suites[ARRAY_SIZE(wilc_cipher_suites)];
+ u64 inc_roc_cookie;
+};
+
+struct frame_reg {
+ u16 type;
+ bool reg;
+};
+
+#define MAX_TCP_SESSION 25
+#define MAX_PENDING_ACKS 256
+
+struct ack_session_info {
+ u32 seq_num;
+ u32 bigger_ack_num;
+ u16 src_port;
+ u16 dst_port;
+ u16 status;
+};
+
+struct pending_acks {
+ u32 ack_num;
+ u32 session_index;
+ struct txq_entry_t *txqe;
+};
+
+struct tcp_ack_filter {
+ struct ack_session_info ack_session_info[2 * MAX_TCP_SESSION];
+ struct pending_acks pending_acks[MAX_PENDING_ACKS];
+ u32 pending_base;
+ u32 tcp_session;
+ u32 pending_acks_idx;
+ bool enabled;
+};
+
+struct wilc_vif {
+ u8 idx;
+ u8 iftype;
+ int monitor_flag;
+ int mac_opened;
+ struct frame_reg frame_reg[NUM_REG_FRAME];
+ struct net_device_stats netstats;
+ struct wilc *wilc;
+ u8 src_addr[ETH_ALEN];
+ u8 bssid[ETH_ALEN];
+ struct host_if_drv *hif_drv;
+ struct net_device *ndev;
+ u8 mode;
+ u8 ifc_id;
+ struct timer_list during_ip_timer;
+ bool obtaining_ip;
+ struct timer_list periodic_rssi;
+ struct rf_info periodic_stat;
+ struct tcp_ack_filter ack_filter;
+ bool connecting;
+};
+
+struct wilc {
+ const struct wilc_hif_func *hif_func;
+ int io_type;
+ s8 mac_status;
+ struct gpio_desc *gpio_irq;
+ bool initialized;
+ int dev_irq_num;
+ int close;
+ u8 vif_num;
+ struct wilc_vif *vif[WILC_NUM_CONCURRENT_IFC];
+ u8 open_ifcs;
+ /*protect head of transmit queue*/
+ struct mutex txq_add_to_head_cs;
+ /*protect txq_entry_t transmit queue*/
+ spinlock_t txq_spinlock;
+ /*protect rxq_entry_t receiver queue*/
+ struct mutex rxq_cs;
+ /* lock to protect hif access */
+ struct mutex hif_cs;
+
+ struct completion cfg_event;
+ struct completion sync_event;
+ struct completion txq_event;
+ struct completion txq_thread_started;
+
+ struct task_struct *txq_thread;
+
+ int quit;
+ /* lock to protect issue of wid command to firmware */
+ struct mutex cfg_cmd_lock;
+ struct wilc_cfg_frame cfg_frame;
+ u32 cfg_frame_offset;
+ u8 cfg_seq_no;
+
+ u8 *rx_buffer;
+ u32 rx_buffer_offset;
+ u8 *tx_buffer;
+
+ struct txq_entry_t txq_head;
+ int txq_entries;
+
+ struct rxq_entry_t rxq_head;
+
+ const struct firmware *firmware;
+
+ struct device *dev;
+ bool suspend_event;
+
+ bool enable_ps;
+ int clients_count;
+ struct workqueue_struct *hif_workqueue;
+ enum chip_ps_states chip_ps_state;
+ struct wilc_cfg cfg;
+ void *bus_data;
+ struct net_device *monitor_dev;
+ /* deinit lock */
+ struct mutex deinit_lock;
+ u8 sta_ch;
+ u8 op_ch;
+};
+
+struct wilc_wfi_mon_priv {
+ struct net_device *real_ndev;
+};
+
+void wilc_frmw_to_host(struct wilc *wilc, u8 *buff, u32 size, u32 pkt_offset);
+void wilc_mac_indicate(struct wilc *wilc);
+void wilc_netdev_cleanup(struct wilc *wilc);
+int wilc_netdev_init(struct wilc **wilc, struct device *dev, int io_type,
+ const struct wilc_hif_func *ops);
+void wilc_wfi_mgmt_rx(struct wilc *wilc, u8 *buff, u32 size);
+void wilc_wlan_set_bssid(struct net_device *wilc_netdev, u8 *bssid, u8 mode);
+
+#endif
--
2.7.4
next prev parent reply other threads:[~2019-02-09 7:12 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-09 7:12 [PATCH 00/16] wilc1000: move out of staging Ajay.Kathat
2019-02-09 7:12 ` [PATCH 01/16] wilc1000: add host_interface.h Ajay.Kathat
2019-02-09 7:12 ` [PATCH 02/16] wilc1000: add host_interface.c Ajay.Kathat
2019-02-09 7:12 ` [PATCH 03/16] wilc1000: add wilc_wlan_if.h Ajay.Kathat
2019-02-09 7:12 ` [PATCH 04/16] wilc1000: add wilc_wlan_cfg.h Ajay.Kathat
2019-02-09 7:12 ` [PATCH 05/16] wilc1000: add wilc_wlan_cfg.c Ajay.Kathat
2019-02-09 7:12 ` Ajay.Kathat [this message]
2019-02-09 7:12 ` [PATCH 07/16] wilc1000: add wilc_wfi_cfgoperations.h Ajay.Kathat
2019-02-09 7:12 ` [PATCH 08/16] wilc1000: add wilc_wfi_cfgoperations.c Ajay.Kathat
2019-02-09 7:12 ` [PATCH 09/16] wilc1000: add wilc_netdev.c Ajay.Kathat
2019-02-09 7:12 ` [PATCH 10/16] wilc1000: add wilc_mon.c Ajay.Kathat
2019-02-09 7:12 ` [PATCH 11/16] wilc1000: add wilc_spi.c Ajay.Kathat
2019-02-09 7:12 ` [PATCH 12/16] wilc1000: add wilc_wlan.c Ajay.Kathat
2019-02-09 7:12 ` [PATCH 13/16] wilc1000: add wilc_wlan.h Ajay.Kathat
2019-02-09 7:12 ` [PATCH 14/16] wilc1000: add wilc_sdio.c Ajay.Kathat
2019-02-09 7:13 ` [PATCH 15/16] wilc1000: updated DT device binding for wilc1000 device Ajay.Kathat
2019-02-09 7:13 ` [PATCH 16/16] wilc1000: add Makefile and Kconfig files for wilc1000 compilation Ajay.Kathat
2019-03-21 12:49 ` [PATCH 00/16] wilc1000: move out of staging Ajay.Kathat
2019-03-21 12:54 ` Kalle Valo
2019-03-21 14:06 ` Ajay.Kathat
2019-05-23 13:32 ` Ajay.Kathat
2019-05-23 14:13 ` Kalle Valo
2019-05-23 16:45 ` Ajay.Kathat
2019-05-31 4:53 ` Ajay.Kathat
2019-05-31 6:23 ` Kalle Valo
2019-05-31 7:11 ` Ajay.Kathat
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1549696298-9795-7-git-send-email-ajay.kathat@microchip.com \
--to=ajay.kathat@microchip.com \
--cc=Adham.Abozaeid@microchip.com \
--cc=Claudiu.Beznea@microchip.com \
--cc=Nicolas.Ferre@microchip.com \
--cc=Venkateswara.Kaja@microchip.com \
--cc=gregkh@linuxfoundation.org \
--cc=johannes@sipsolutions.net \
--cc=kvalo@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).