From: Rajkumar Manoharan <rmanohar@codeaurora.org>
To: johannes@sipsolutions.net, kvalo@codeaurora.org
Cc: linux-wireless@vger.kernel.org, ath11k@lists.infradead.org,
Rajkumar Manoharan <rmanohar@codeaurora.org>
Subject: [PATCH v3 03/11] nl80211: add HE 6 GHz Band Capability support
Date: Fri, 8 May 2020 17:12:57 -0700 [thread overview]
Message-ID: <1588983185-5741-3-git-send-email-rmanohar@codeaurora.org> (raw)
In-Reply-To: <1588983185-5741-1-git-send-email-rmanohar@codeaurora.org>
Define new structures for HE 6 GHz band capabilities as per
IEEE P802.11ax/D6.0, 9.4.2.261 HE 6 GHz Band Capabilities element
and 6 GHz Operation Information field of HE operation element
(IEEE P802.11ax/D6.0, Figure 9-787k).
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
---
include/linux/ieee80211.h | 57 +++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 57 insertions(+)
diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h
index 16268ef1cbcc..77462dff6db3 100644
--- a/include/linux/ieee80211.h
+++ b/include/linux/ieee80211.h
@@ -1632,6 +1632,44 @@ struct ieee80211_he_mcs_nss_supp {
} __packed;
/**
+ * enum ieee80211_he_6ghz_chanwidth - HE 6 GHz channel width
+ * @IEEE80211_HE_6GHZ_CHANWIDTH_20MHZ: 20 MHz bandwidth
+ * @IEEE80211_HE_6GHZ_CHANWIDTH_40MHZ: 40 MHz bandwidth
+ * @IEEE80211_HE_6GHZ_CHANWIDTH_80MHZ: 80 MHz bandwidth
+ * @IEEE80211_HE_6GHZ_CHANWIDTH_80P80MHZ: 160 or 80+80 MHz bandwidth
+ */
+enum ieee80211_he_6ghz_chanwidth {
+ IEEE80211_HE_6GHZ_CHANWIDTH_20MHZ = 0,
+ IEEE80211_HE_6GHZ_CHANWIDTH_40MHZ = 1,
+ IEEE80211_HE_6GHZ_CHANWIDTH_80MHZ = 2,
+ IEEE80211_HE_6GHZ_CHANWIDTH_160MHZ_80P80MHZ = 3,
+};
+
+/**
+ * struct ieee80211_he_oper_6ghz_op_info - 6 GHz Operation Information
+ *
+ * This structure is defined as described in IEEE P802.11ax/D6.0,
+ * Figure 9-787k—6 GHz Operation Information field.
+ *
+ * @primary_chan: The channel number of the primary channel in the 6 GHz band.
+ * @control: First two bits defines channel width field indicates the BSS
+ * channel width and is set to 0 for 20 MHz, 1 for 40 MHz, 2 for 80 MHz,
+ * and 3 for 80+80 or 160 MHz.
+ * @center_freq_seg0_idx: Channel center frequency index for the 20 MHz,
+ * 40 MHz, or 80 MHz, or 80+80 MHz.
+ * @center_freq_seg1_idx: Channel center frequency index of the 160 MHz.
+ * @min_rate: Minimum rate, in units of 1 Mb/s, that the non-AP STA is allowed
+ * to use for sending PPDUs.
+ */
+struct ieee80211_he_oper_6ghz_op_info {
+ u8 primary_chan;
+ u8 control;
+ u8 center_freq_seg0_idx;
+ u8 center_freq_seg1_idx;
+ u8 min_rate;
+} __packed;
+
+/**
* struct ieee80211_he_operation - HE capabilities element
*
* This structure is the "HE operation element" fields as
@@ -1682,6 +1720,15 @@ struct ieee80211_mu_edca_param_set {
struct ieee80211_he_mu_edca_param_ac_rec ac_vo;
} __packed;
+/**
+ * struct ieee80211_he_6ghz_band_cap - HE 6 GHz Band Capabilities element
+ *
+ * This structure is defined as described in IEEE P802.11ax/D6.0, 9.4.2.261.
+ */
+struct ieee80211_he_6ghz_band_cap {
+ __le16 capab;
+} __packed;
+
/* 802.11ac VHT Capabilities */
#define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_3895 0x00000000
#define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_7991 0x00000001
@@ -1982,6 +2029,15 @@ int ieee80211_get_vht_max_nss(struct ieee80211_vht_cap *cap,
#define IEEE80211_TX_RX_MCS_NSS_SUPP_TX_BITMAP_MASK 0x07c0
#define IEEE80211_TX_RX_MCS_NSS_SUPP_RX_BITMAP_MASK 0xf800
+/* 802.11ax HE 6 GHz Band Capability */
+#define IEEE80211_HE_6GHZ_CAP_MIN_MPDU_START_SPACE_MASK GENMASK(2, 0)
+#define IEEE80211_HE_6GHZ_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK GENMASK(5, 3)
+#define IEEE80211_HE_6GHZ_CAP_MAX_MPDU_LENGTH_MASK GENMASK(7, 6)
+#define IEEE80211_HE_6GHZ_CAP_SMPS_MASK GENMASK(10, 9)
+#define IEEE80211_HE_6GHZ_CAP_RD_RESP BIT(11)
+#define IEEE80211_HE_6GHZ_CAP_RX_ANTENNA_PATTERN BIT(12)
+#define IEEE80211_HE_6GHZ_CAP_TX_ANTENNA_PATTERN BIT(13)
+
/* TX/RX HE MCS Support field Highest MCS subfield encoding */
enum ieee80211_he_highest_mcs_supported_subfield_enc {
HIGHEST_MCS_SUPPORTED_MCS7 = 0,
@@ -2059,6 +2115,7 @@ ieee80211_he_ppe_size(u8 ppe_thres_hdr, const u8 *phy_cap_info)
#define IEEE80211_HE_OPERATION_BSS_COLOR_OFFSET 24
#define IEEE80211_HE_OPERATION_PARTIAL_BSS_COLOR 0x40000000
#define IEEE80211_HE_OPERATION_BSS_COLOR_DISABLED 0x80000000
+#define IEEE80211_HE_OPERATION_6GHZ_OP_INFO_CTRL_CHAN_WIDTH 0x3
/*
* ieee80211_he_oper_size - calculate 802.11ax HE Operations IE size
--
2.7.4
next prev parent reply other threads:[~2020-05-09 0:13 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-09 0:12 [PATCH v3 01/11] cfg80211: use only HE capability to set prohibited flags in 6 GHz Rajkumar Manoharan
2020-05-09 0:12 ` [PATCH v3 02/11] cfg80211: handle 6 GHz capability of new station Rajkumar Manoharan
2020-05-09 0:12 ` Rajkumar Manoharan [this message]
2020-05-09 0:12 ` [PATCH v3 04/11] mac80211: add HE 6 GHz Band Capabilities into parse extension Rajkumar Manoharan
2020-05-09 0:12 ` [PATCH v3 05/11] mac80211: fix memory overlap due to variable length param Rajkumar Manoharan
2020-05-09 0:13 ` [PATCH v3 06/11] mac80211: handle HE 6 GHz Capability in HE STA processing Rajkumar Manoharan
2020-05-09 0:13 ` [PATCH v3 07/11] mac80211: add HE 6 GHz Band Capability IE in Assoc. Request Rajkumar Manoharan
2020-05-09 0:13 ` [PATCH v3 08/11] mac80211: build HE operation with 6 GHz oper information Rajkumar Manoharan
2020-05-09 0:13 ` [PATCH v3 09/11] mac80211: do not allow HT/VHT IEs in 6 GHz mesh mode Rajkumar Manoharan
2020-05-09 0:13 ` [PATCH v3 10/11] mac80211: determine chantype from HE operation in 6 GHz Rajkumar Manoharan
2020-05-09 0:13 ` [PATCH v3 11/11] ath11k: build HE 6 GHz capability Rajkumar Manoharan
2020-05-13 19:44 [PATCH v3 01/11] cfg80211: use only HE capability to set prohibited flags in 6 GHz Rajkumar Manoharan
2020-05-13 19:44 ` [PATCH v3 03/11] nl80211: add HE 6 GHz Band Capability support Rajkumar Manoharan
2020-05-27 14:27 ` Johannes Berg
2020-05-27 17:39 ` Rajkumar Manoharan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1588983185-5741-3-git-send-email-rmanohar@codeaurora.org \
--to=rmanohar@codeaurora.org \
--cc=ath11k@lists.infradead.org \
--cc=johannes@sipsolutions.net \
--cc=kvalo@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).