From: Kalle Valo <kvalo@codeaurora.org>
To: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Cc: <ath11k@lists.infradead.org>, <linux-wireless@vger.kernel.org>,
Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Subject: Re: [PATCH] ath11k: add hw_param for wakeup_mhi
Date: Fri, 19 Nov 2021 08:04:52 +0000 (UTC) [thread overview]
Message-ID: <163730908439.10050.9686803784287020188.kvalo@codeaurora.org> (raw)
In-Reply-To: <1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com>
Seevalamuthu Mariappan <quic_seevalam@quicinc.com> wrote:
> Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
> wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
> QCN9074 when doing 'rmmod ath11k_pci':
>
> Kernel panic - not syncing: dev_wake != 0
> CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
> Hardware name: Generic DT based system
> [<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
> [<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
> [<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
> [<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
> [<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
> [<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
> [E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
> [E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
> [E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
> [<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
> [<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
> [<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
> [<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
> [<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
> [<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
> [<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)
>
> Hence, disable wakeup/release mhi using hw_param for other hardwares.
>
> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1
>
> Fixes: a05bd8513335 ("ath11k: read and write registers below unwindowed address")
> Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Patch applied to ath-next branch of ath.git, thanks.
081e2d6476e3 ath11k: add hw_param for wakeup_mhi
--
https://patchwork.kernel.org/project/linux-wireless/patch/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
prev parent reply other threads:[~2021-11-19 8:04 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-11-12 7:26 [PATCH] ath11k: add hw_param for wakeup_mhi Seevalamuthu Mariappan
2021-11-15 10:21 ` Kalle Valo
2021-11-16 8:04 ` Seevalamuthu Mariappan (Temp) (QUIC)
2021-11-17 7:43 ` Kalle Valo
2021-11-19 8:04 ` Kalle Valo [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=163730908439.10050.9686803784287020188.kvalo@codeaurora.org \
--to=kvalo@codeaurora.org \
--cc=ath11k@lists.infradead.org \
--cc=linux-wireless@vger.kernel.org \
--cc=quic_seevalam@quicinc.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).