linux-wireless.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: greearb@candelatech.com
To: linux-wireless@vger.kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Subject: [PATCH v3 2/2] mt76: mt7915: fix radar detector logic
Date: Fri, 20 Aug 2021 13:35:31 -0700	[thread overview]
Message-ID: <20210820203531.20706-2-greearb@candelatech.com> (raw)
In-Reply-To: <20210820203531.20706-1-greearb@candelatech.com>

From: Ben Greear <greearb@candelatech.com>

Before this patch, if AP went from ch 100 to ch 36, the radar detector
logic in the firmware was not being disabled.  This made the AP appear
to be up, but no beacons were seen on air until module reload or
reboot.

To reproduce this, I change hostapd.conf and restart hostapd.  Others
on openwrt used their UI to make changes and problem was seen, but
stil others changed channels in some other way and/or had some other
difference and could *not* reproduce it.  So, something perhaps a
bit subtle.

To fix the problem, stop depending on comparing dfs_state, store last
freq/bandwidth to detect changes in that, and streamline code that
checks to enable/disable radar detection.  And add in error checking
and dev_dbg logic so one can see what is actually happening if need
to debug this again.

Signed-off-by: Ben Greear <greearb@candelatech.com>
---
 .../net/wireless/mediatek/mt76/mt7915/init.c  |   7 +-
 .../net/wireless/mediatek/mt76/mt7915/mac.c   | 102 ++++++++++++------
 .../net/wireless/mediatek/mt76/mt7915/main.c  |  23 +++-
 .../wireless/mediatek/mt76/mt7915/mt7915.h    |   6 +-
 4 files changed, 100 insertions(+), 38 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/init.c b/drivers/net/wireless/mediatek/mt76/mt7915/init.c
index f46ea989a348..543bb1e947e3 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/init.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/init.c
@@ -205,6 +205,7 @@ mt7915_regd_notifier(struct wiphy *wiphy,
 	struct mt76_phy *mphy = hw->priv;
 	struct mt7915_phy *phy = mphy->priv;
 	struct cfg80211_chan_def *chandef = &mphy->chandef;
+	int ret;
 
 	memcpy(dev->mt76.alpha2, request->alpha2, sizeof(dev->mt76.alpha2));
 	dev->mt76.region = request->dfs_region;
@@ -215,7 +216,10 @@ mt7915_regd_notifier(struct wiphy *wiphy,
 	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR))
 		return;
 
-	mt7915_dfs_init_radar_detector(phy);
+	ret = mt7915_dfs_init_radar_detector(phy);
+	if (ret < 0)
+		dev_err(dev->mt76.dev, "init-wifi: dfs-init-radar-detector failed: %d",
+			ret);
 }
 
 static void
@@ -832,7 +836,6 @@ int mt7915_register_device(struct mt7915_dev *dev)
 
 	dev->mphy.hw->wiphy->available_antennas_rx = dev->mphy.chainmask;
 	dev->mphy.hw->wiphy->available_antennas_tx = dev->mphy.chainmask;
-	dev->phy.dfs_state = -1;
 
 #ifdef CONFIG_NL80211_TESTMODE
 	dev->mt76.test_ops = &mt7915_testmode_ops;
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mac.c b/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
index a6e142d27b60..f61c98905458 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
@@ -2404,14 +2404,29 @@ void mt7915_mac_work(struct work_struct *work)
 				     MT7915_WATCHDOG_TIME);
 }
 
-static void mt7915_dfs_stop_radar_detector(struct mt7915_phy *phy)
+int mt7915_dfs_stop_radar_detector(struct mt7915_phy *phy, bool ext_phy)
 {
 	struct mt7915_dev *dev = phy->dev;
+	int err;
+
+	dev_dbg(dev->mt76.dev, "dfs-stop-radar-detector, rdd-state: 0x%x",
+		phy->rdd_state);
+
+	err = mt7915_mcu_rdd_cmd(dev, RDD_NORMAL_START, ext_phy,
+				 MT_RX_SEL0, 0);
+	if (err < 0) {
+		dev_err(dev->mt76.dev, "mcu-rdd-cmd RDD_NORMAL_START failed: %d",
+			err);
+		/* I think best to carry on, even if we have an error here. */
+	}
 
 	if (phy->rdd_state & BIT(0))
 		mt7915_mcu_rdd_cmd(dev, RDD_STOP, 0, MT_RX_SEL0, 0);
 	if (phy->rdd_state & BIT(1))
 		mt7915_mcu_rdd_cmd(dev, RDD_STOP, 1, MT_RX_SEL0, 0);
+	phy->rdd_state = 0;
+
+	return err;
 }
 
 static int mt7915_dfs_start_rdd(struct mt7915_dev *dev, int chain)
@@ -2419,10 +2434,14 @@ static int mt7915_dfs_start_rdd(struct mt7915_dev *dev, int chain)
 	int err;
 
 	err = mt7915_mcu_rdd_cmd(dev, RDD_START, chain, MT_RX_SEL0, 0);
+
+	dev_dbg(dev->mt76.dev, "dfs-start-rdd, RDD_START rv: %d", err);
 	if (err < 0)
 		return err;
 
-	return mt7915_mcu_rdd_cmd(dev, RDD_DET_MODE, chain, MT_RX_SEL0, 1);
+	err = mt7915_mcu_rdd_cmd(dev, RDD_DET_MODE, chain, MT_RX_SEL0, 1);
+	dev_dbg(dev->mt76.dev, "dfs-start-rdd, RDD_DET_MODE rv: %d", err);
+	return err;
 }
 
 static int mt7915_dfs_start_radar_detector(struct mt7915_phy *phy)
@@ -2523,47 +2542,68 @@ int mt7915_dfs_init_radar_detector(struct mt7915_phy *phy)
 	int err;
 	struct mt7915_vif_counts counts = {0};
 
-	if (dev->mt76.region == NL80211_DFS_UNSET) {
-		phy->dfs_state = -1;
-		if (phy->rdd_state)
-			goto stop;
+	dev_dbg(dev->mt76.dev,
+		"dfs-init-radar-detector, region: %d freq: %d chandef dfs-state: %d",
+		dev->mt76.region, chandef->chan->center_freq,
+		chandef->chan->dfs_state);
 
+	if (test_bit(MT76_SCANNING, &phy->mt76->state)) {
+		dev_dbg(dev->mt76.dev, "init-radar, was scanning, no change.\n");
 		return 0;
 	}
 
-	if (test_bit(MT76_SCANNING, &phy->mt76->state))
-		return 0;
+	if (dev->mt76.region == NL80211_DFS_UNSET) {
+		dev_dbg(dev->mt76.dev,
+			"dfs-init-radar, region is UNSET, disable radar.");
+		goto stop;
+	}
+
+	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR)) {
+		dev_dbg(dev->mt76.dev,
+			"dfs-init-radar, chandef does not want radar.");
+		goto stop;
+	}
 
-	if (phy->dfs_state == chandef->chan->dfs_state)
+	ieee80211_iterate_active_interfaces(phy->mt76->hw,
+					    IEEE80211_IFACE_ITER_RESUME_ALL,
+					    mt7915_vif_counts, &counts);
+
+	if (!(counts.ap + counts.adhoc + counts.mesh)) {
+		/* No beaconning interfaces, do not start CAC */
+		dev_dbg(dev->mt76.dev,
+			"dfs-init-radar, no AP/Mesh/Adhoc vifs active, stop radar.");
+		goto stop;
+	}
+
+	/* At this point, we need radar detection, see if we have started
+	 * it already.
+	 */
+	if (phy->rdd_state) {
+		if (chandef->chan->dfs_state == NL80211_DFS_AVAILABLE) {
+			/* CAC is already complete. */
+			dev_dbg(dev->mt76.dev,
+				"init-radar, RADAR started and DFS state is AVAILABLE, call RDD_CAC_END");
+			return mt7915_mcu_rdd_cmd(dev, RDD_CAC_END, ext_phy,
+						  MT_RX_SEL0, 0);
+		}
+		dev_dbg(dev->mt76.dev,
+			"init-radar, rdd_state indicates RADAR already started,"
+			" DFS state: %d not YET available, rdd_state: 0x%x",
+			chandef->chan->dfs_state, phy->rdd_state);
 		return 0;
+	}
 
 	err = mt7915_dfs_init_radar_specs(phy);
 	if (err < 0) {
-		phy->dfs_state = -1;
+		dev_err(dev->mt76.dev, "dfs-init-radar-specs failed: %d",
+			err);
 		goto stop;
 	}
 
-	phy->dfs_state = chandef->chan->dfs_state;
-
-	if (chandef->chan->flags & IEEE80211_CHAN_RADAR) {
-		if (chandef->chan->dfs_state != NL80211_DFS_AVAILABLE) {
-			ieee80211_iterate_active_interfaces(phy->mt76->hw,
-				IEEE80211_IFACE_ITER_RESUME_ALL,
-				mt7915_vif_counts, &counts);
-			if (counts.ap + counts.adhoc + counts.mesh)
-				mt7915_dfs_start_radar_detector(phy);
-			return 0;
-		}
-		return mt7915_mcu_rdd_cmd(dev, RDD_CAC_END, ext_phy,
-					  MT_RX_SEL0, 0);
-	}
+	err = mt7915_dfs_start_radar_detector(phy);
+	dev_dbg(dev->mt76.dev, "dfs-start-radar-detector rv: %d", err);
+	return err;
 
 stop:
-	err = mt7915_mcu_rdd_cmd(dev, RDD_NORMAL_START, ext_phy,
-				 MT_RX_SEL0, 0);
-	if (err < 0)
-		return err;
-
-	mt7915_dfs_stop_radar_detector(phy);
-	return 0;
+	return mt7915_dfs_stop_radar_detector(phy, ext_phy);
 }
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/main.c b/drivers/net/wireless/mediatek/mt76/mt7915/main.c
index f3df5ea066a2..6bffddb63461 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/main.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/main.c
@@ -298,6 +298,8 @@ static void mt7915_init_dfs_state(struct mt7915_phy *phy)
 	struct mt76_phy *mphy = phy->mt76;
 	struct ieee80211_hw *hw = mphy->hw;
 	struct cfg80211_chan_def *chandef = &hw->conf.chandef;
+	struct mt7915_dev *dev = phy->dev;
+	bool ext_phy = phy != &dev->phy;
 
 	if (hw->conf.flags & IEEE80211_CONF_OFFCHANNEL)
 		return;
@@ -305,11 +307,23 @@ static void mt7915_init_dfs_state(struct mt7915_phy *phy)
 	if (!(chandef->chan->flags & IEEE80211_CHAN_RADAR))
 		return;
 
-	if (mphy->chandef.chan->center_freq == chandef->chan->center_freq &&
-	    mphy->chandef.width == chandef->width)
+	if (phy->dfs_center_freq == chandef->chan->center_freq &&
+	    phy->dfs_ch_width == chandef->width)
 		return;
 
-	phy->dfs_state = -1;
+	/* We are being moved to a new frequency/bw, still on DFS.  Stop
+	 * any existing DFS, then will start it again in the
+	 * init-radar-detector logic.
+	 */
+	if (phy->rdd_state) {
+		dev_dbg(dev->mt76.dev,
+			"init-dfs-state, channel changed, old: %d:%d  new: %d:%d, stopping radar.",
+			phy->dfs_center_freq, phy->dfs_ch_width,
+			chandef->chan->center_freq, chandef->width);
+		mt7915_dfs_stop_radar_detector(phy, ext_phy);
+	}
+	phy->dfs_center_freq = chandef->chan->center_freq;
+	phy->dfs_ch_width = chandef->width;
 }
 
 int mt7915_set_channel(struct mt7915_phy *phy)
@@ -337,6 +351,9 @@ int mt7915_set_channel(struct mt7915_phy *phy)
 
 	mt7915_mac_set_timing(phy);
 	ret = mt7915_dfs_init_radar_detector(phy);
+	if (ret < 0)
+		dev_err(dev->mt76.dev, "set-channel: dfs-init-radar-detector failed: %d",
+			ret);
 	mt7915_mac_cca_stats_reset(phy);
 
 	mt7915_mac_reset_counters(phy);
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h b/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h
index f46816cefa3f..a9f55748cf1e 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h
@@ -284,8 +284,9 @@ struct mt7915_phy {
 	s16 coverage_class;
 	u8 slottime;
 
-	u8 rdd_state;
-	int dfs_state;
+	u8 rdd_state; /* radar detection started bitfield */
+	enum nl80211_chan_width dfs_ch_width;
+	u32 dfs_center_freq;
 
 	u32 rx_ampdu_ts;
 	u32 ampdu_ref;
@@ -574,6 +575,7 @@ int mt7915_dfs_init_radar_detector(struct mt7915_phy *phy);
 void mt7915_set_stream_he_caps(struct mt7915_phy *phy);
 void mt7915_set_stream_vht_txbf_caps(struct mt7915_phy *phy);
 void mt7915_update_channel(struct mt76_phy *mphy);
+int mt7915_dfs_stop_radar_detector(struct mt7915_phy *phy, bool ext_phy);
 int mt7915_init_debugfs(struct mt7915_dev *dev);
 #ifdef CONFIG_MAC80211_DEBUGFS
 void mt7915_sta_add_debugfs(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
-- 
2.20.1


  reply	other threads:[~2021-08-20 20:35 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-08-20 20:35 [PATCH v3 1/2] mt76: mt7915: fix STA mode connection on DFS channels greearb
2021-08-20 20:35 ` greearb [this message]
2021-11-10 20:32   ` [PATCH v3 2/2] mt76: mt7915: fix radar detector logic Ben Greear
2021-11-10 22:36     ` Janusz Dziedzic
2021-08-29 18:17 ` [PATCH v3 1/2] mt76: mt7915: fix STA mode connection on DFS channels Janusz Dziedzic
2021-08-30 22:38   ` Ben Greear

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210820203531.20706-2-greearb@candelatech.com \
    --to=greearb@candelatech.com \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).