From: Lukas Wunner <lukas@wunner.de>
To: Kalle Valo <kvalo@kernel.org>,
Amitkumar Karwar <amitkarwar@gmail.com>,
Ganapathi Bhat <ganapathi017@gmail.com>,
Sharvari Harisangam <sharvari.harisangam@nxp.com>,
Xinming Hu <huxinming820@gmail.com>
Cc: linux-wireless@vger.kernel.org, Sherry Sun <sherry.sun@nxp.com>,
Matt Ranostay <mranostay@ti.com>
Subject: [PATCH 2/3] wifi: mwifiex: Support SD8978 chipset
Date: Fri, 27 Jan 2023 15:02:00 +0100 [thread overview]
Message-ID: <536b4f17a72ca460ad1b07045757043fb0778988.1674827105.git.lukas@wunner.de> (raw)
In-Reply-To: <cover.1674827105.git.lukas@wunner.de>
The Marvell SD8978 (aka NXP IW416) uses identical registers as SD8987,
so reuse the existing mwifiex_reg_sd8987 definition.
Note that mwifiex_reg_sd8977 and mwifiex_reg_sd8997 are likewise
identical, save for the fw_dump_ctrl register: They define it as 0xf0
whereas mwifiex_reg_sd8987 defines it as 0xf9. I've verified that
0xf9 is the correct value on SD8978. NXP's out-of-tree driver uses
0xf9 for all of them, so there's a chance that 0xf0 is not correct
in the mwifiex_reg_sd8977 and mwifiex_reg_sd8997 definitions. I cannot
test that for lack of hardware, hence am leaving it as is.
NXP has only released a firmware which runs Bluetooth over UART.
Perhaps Bluetooth over SDIO is unsupported by this chipset.
Consequently, only an "sdiouart" firmware image is referenced, not an
alternative "sdsd" image.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
---
.../bindings/net/wireless/marvell-8xxx.txt | 4 ++-
drivers/net/wireless/marvell/mwifiex/Kconfig | 5 ++--
drivers/net/wireless/marvell/mwifiex/sdio.c | 25 +++++++++++++++++--
drivers/net/wireless/marvell/mwifiex/sdio.h | 1 +
include/linux/mmc/sdio_ids.h | 1 +
5 files changed, 31 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt
index 9bf9bbac16e2..cdc303caf5f4 100644
--- a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt
+++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt
@@ -1,4 +1,4 @@
-Marvell 8787/8897/8997 (sd8787/sd8897/sd8997/pcie8997) SDIO/PCIE devices
+Marvell 8787/8897/8978/8997 (sd8787/sd8897/sd8978/sd8997/pcie8997) SDIO/PCIE devices
------
This node provides properties for controlling the Marvell SDIO/PCIE wireless device.
@@ -10,7 +10,9 @@ Required properties:
- compatible : should be one of the following:
* "marvell,sd8787"
* "marvell,sd8897"
+ * "marvell,sd8978"
* "marvell,sd8997"
+ * "nxp,iw416"
* "pci11ab,2b42"
* "pci1b4b,2b42"
diff --git a/drivers/net/wireless/marvell/mwifiex/Kconfig b/drivers/net/wireless/marvell/mwifiex/Kconfig
index 2b4ff2b78a7e..b182f7155d66 100644
--- a/drivers/net/wireless/marvell/mwifiex/Kconfig
+++ b/drivers/net/wireless/marvell/mwifiex/Kconfig
@@ -10,13 +10,14 @@ config MWIFIEX
mwifiex.
config MWIFIEX_SDIO
- tristate "Marvell WiFi-Ex Driver for SD8786/SD8787/SD8797/SD8887/SD8897/SD8977/SD8987/SD8997"
+ tristate "Marvell WiFi-Ex Driver for SD8786/SD8787/SD8797/SD8887/SD8897/SD8977/SD8978/SD8987/SD8997"
depends on MWIFIEX && MMC
select FW_LOADER
select WANT_DEV_COREDUMP
help
This adds support for wireless adapters based on Marvell
- 8786/8787/8797/8887/8897/8977/8987/8997 chipsets with SDIO interface.
+ 8786/8787/8797/8887/8897/8977/8978/8987/8997 chipsets with
+ SDIO interface. SD8978 is also known as NXP IW416.
If you choose to build it as a module, it will be called
mwifiex_sdio.
diff --git a/drivers/net/wireless/marvell/mwifiex/sdio.c b/drivers/net/wireless/marvell/mwifiex/sdio.c
index 9f506efa5370..c64e24c10ea6 100644
--- a/drivers/net/wireless/marvell/mwifiex/sdio.c
+++ b/drivers/net/wireless/marvell/mwifiex/sdio.c
@@ -263,7 +263,7 @@ static const struct mwifiex_sdio_card_reg mwifiex_reg_sd8887 = {
0x68, 0x69, 0x6a},
};
-static const struct mwifiex_sdio_card_reg mwifiex_reg_sd8987 = {
+static const struct mwifiex_sdio_card_reg mwifiex_reg_sd89xx = {
.start_rd_port = 0,
.start_wr_port = 0,
.base_0_reg = 0xF8,
@@ -394,6 +394,22 @@ static const struct mwifiex_sdio_device mwifiex_sdio_sd8977 = {
.can_ext_scan = true,
};
+static const struct mwifiex_sdio_device mwifiex_sdio_sd8978 = {
+ .firmware_sdiouart = SD8978_SDIOUART_FW_NAME,
+ .reg = &mwifiex_reg_sd89xx,
+ .max_ports = 32,
+ .mp_agg_pkt_limit = 16,
+ .tx_buf_size = MWIFIEX_TX_DATA_BUF_SIZE_4K,
+ .mp_tx_agg_buf_size = MWIFIEX_MP_AGGR_BUF_SIZE_MAX,
+ .mp_rx_agg_buf_size = MWIFIEX_MP_AGGR_BUF_SIZE_MAX,
+ .supports_sdio_new_mode = true,
+ .has_control_mask = false,
+ .can_dump_fw = true,
+ .fw_dump_enh = true,
+ .can_auto_tdls = false,
+ .can_ext_scan = true,
+};
+
static const struct mwifiex_sdio_device mwifiex_sdio_sd8997 = {
.firmware = SD8997_DEFAULT_FW_NAME,
.firmware_sdiouart = SD8997_SDIOUART_FW_NAME,
@@ -428,7 +444,7 @@ static const struct mwifiex_sdio_device mwifiex_sdio_sd8887 = {
static const struct mwifiex_sdio_device mwifiex_sdio_sd8987 = {
.firmware = SD8987_DEFAULT_FW_NAME,
- .reg = &mwifiex_reg_sd8987,
+ .reg = &mwifiex_reg_sd89xx,
.max_ports = 32,
.mp_agg_pkt_limit = 16,
.tx_buf_size = MWIFIEX_TX_DATA_BUF_SIZE_2K,
@@ -482,7 +498,9 @@ static struct memory_type_mapping mem_type_mapping_tbl[] = {
static const struct of_device_id mwifiex_sdio_of_match_table[] = {
{ .compatible = "marvell,sd8787" },
{ .compatible = "marvell,sd8897" },
+ { .compatible = "marvell,sd8978" },
{ .compatible = "marvell,sd8997" },
+ { .compatible = "nxp,iw416" },
{ }
};
@@ -920,6 +938,8 @@ static const struct sdio_device_id mwifiex_ids[] = {
.driver_data = (unsigned long)&mwifiex_sdio_sd8801},
{SDIO_DEVICE(SDIO_VENDOR_ID_MARVELL, SDIO_DEVICE_ID_MARVELL_8977_WLAN),
.driver_data = (unsigned long)&mwifiex_sdio_sd8977},
+ {SDIO_DEVICE(SDIO_VENDOR_ID_MARVELL, SDIO_DEVICE_ID_MARVELL_8978_WLAN),
+ .driver_data = (unsigned long)&mwifiex_sdio_sd8978},
{SDIO_DEVICE(SDIO_VENDOR_ID_MARVELL, SDIO_DEVICE_ID_MARVELL_8987_WLAN),
.driver_data = (unsigned long)&mwifiex_sdio_sd8987},
{SDIO_DEVICE(SDIO_VENDOR_ID_MARVELL, SDIO_DEVICE_ID_MARVELL_8997_WLAN),
@@ -3164,6 +3184,7 @@ MODULE_FIRMWARE(SD8797_DEFAULT_FW_NAME);
MODULE_FIRMWARE(SD8897_DEFAULT_FW_NAME);
MODULE_FIRMWARE(SD8887_DEFAULT_FW_NAME);
MODULE_FIRMWARE(SD8977_DEFAULT_FW_NAME);
+MODULE_FIRMWARE(SD8978_SDIOUART_FW_NAME);
MODULE_FIRMWARE(SD8987_DEFAULT_FW_NAME);
MODULE_FIRMWARE(SD8997_DEFAULT_FW_NAME);
MODULE_FIRMWARE(SD8997_SDIOUART_FW_NAME);
diff --git a/drivers/net/wireless/marvell/mwifiex/sdio.h b/drivers/net/wireless/marvell/mwifiex/sdio.h
index 3a24bb48b299..ae94c172310f 100644
--- a/drivers/net/wireless/marvell/mwifiex/sdio.h
+++ b/drivers/net/wireless/marvell/mwifiex/sdio.h
@@ -25,6 +25,7 @@
#define SD8887_DEFAULT_FW_NAME "mrvl/sd8887_uapsta.bin"
#define SD8801_DEFAULT_FW_NAME "mrvl/sd8801_uapsta.bin"
#define SD8977_DEFAULT_FW_NAME "mrvl/sdsd8977_combo_v2.bin"
+#define SD8978_SDIOUART_FW_NAME "mrvl/sdiouartiw416_combo_v0.bin"
#define SD8987_DEFAULT_FW_NAME "mrvl/sd8987_uapsta.bin"
#define SD8997_DEFAULT_FW_NAME "mrvl/sdsd8997_combo_v4.bin"
#define SD8997_SDIOUART_FW_NAME "mrvl/sdiouart8997_combo_v4.bin"
diff --git a/include/linux/mmc/sdio_ids.h b/include/linux/mmc/sdio_ids.h
index 74f9d9a6d330..0e4ef9c5127a 100644
--- a/include/linux/mmc/sdio_ids.h
+++ b/include/linux/mmc/sdio_ids.h
@@ -102,6 +102,7 @@
#define SDIO_DEVICE_ID_MARVELL_8977_BT 0x9146
#define SDIO_DEVICE_ID_MARVELL_8987_WLAN 0x9149
#define SDIO_DEVICE_ID_MARVELL_8987_BT 0x914a
+#define SDIO_DEVICE_ID_MARVELL_8978_WLAN 0x9159
#define SDIO_VENDOR_ID_MEDIATEK 0x037a
#define SDIO_DEVICE_ID_MEDIATEK_MT7663 0x7663
--
2.39.1
next prev parent reply other threads:[~2023-01-27 14:19 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-27 14:00 [PATCH 0/3] mwifiex material for next Lukas Wunner
2023-01-27 14:01 ` [PATCH 1/3] wifi: mwifiex: Add missing compatible string for SD8787 Lukas Wunner
2023-02-13 16:52 ` Kalle Valo
2023-01-27 14:02 ` Lukas Wunner [this message]
2023-01-27 14:03 ` [PATCH 3/3] wifi: mwifiex: Support firmware hotfix version in GET_HW_SPEC responses Lukas Wunner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=536b4f17a72ca460ad1b07045757043fb0778988.1674827105.git.lukas@wunner.de \
--to=lukas@wunner.de \
--cc=amitkarwar@gmail.com \
--cc=ganapathi017@gmail.com \
--cc=huxinming820@gmail.com \
--cc=kvalo@kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=mranostay@ti.com \
--cc=sharvari.harisangam@nxp.com \
--cc=sherry.sun@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).