linux-wireless.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH 1/2] nl80211: vendor-cmd: qca: add command for ap power save
@ 2020-05-20  6:05 Venkateswara Naralasetty
  2020-05-20  6:05 ` [PATCH 2/2] ath11k: Add ap power save support Venkateswara Naralasetty
  2020-07-30 11:45 ` [PATCH 1/2] nl80211: vendor-cmd: qca: add command for ap power save Johannes Berg
  0 siblings, 2 replies; 3+ messages in thread
From: Venkateswara Naralasetty @ 2020-05-20  6:05 UTC (permalink / raw)
  To: ath11k; +Cc: linux-wireless, Venkateswara Naralasetty

This patch is to add vendor command support to enable/disable
ap power save.

An example of usage: iw dev wlanx vendor send 0x1374 0x4a ap-ps <val>

0x1374: vendor id
0x4a: vendor subcmd id
val: 0 - disable power save
     1 - enable power save

Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
---
 include/uapi/nl80211-vnd-qca.h | 42 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)
 create mode 100644 include/uapi/nl80211-vnd-qca.h

diff --git a/include/uapi/nl80211-vnd-qca.h b/include/uapi/nl80211-vnd-qca.h
new file mode 100644
index 0000000..357040a
--- /dev/null
+++ b/include/uapi/nl80211-vnd-qca.h
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier: ISC */
+/*
+ * Copyright (c) 2019-2020 The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _UAPI_NL80211_VND_QCA_H
+#define _UAPI_NL80211_VND_QCA_H
+
+/* Vendor id to be used in vendor specific command and events to user space
+ * NOTE: The authoritative place for definition of QCA_NL80211_VENDOR_ID,
+ * vendor subcmd definitions prefixed with QCA_NL80211_VENDOR_SUBCMD, and
+ * qca_wlan_vendor_attr is open source file src/common/qca-vendor.h in
+ * git://w1.fi/srv/git/hostap.git; the values here are just a copy of that
+ */
+#define QCA_NL80211_VENDOR_ID 0x001374
+
+/**
+ * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION: This vendor subcommand is
+ * used to set wifi configurations by the attributes defined in
+ * enum qca_wlan_vendor_attr_config.
+ */
+enum qca_nl80211_vendor_subcmds {
+	QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_config: Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_GTX: 8-bit unsigned value to trigger
+ * green Tx power saving 1-Enable, 0-Disable.
+ */
+enum qca_wlan_vendor_attr_config {
+	QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57,
+
+	QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
+	QCA_WLAN_VENDOR_ATTR_CONFIG_MAX =
+		QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1,
+};
+#endif /* _UAPI_NL80211_VND_QCA_H_ */
-- 
2.7.4


^ permalink raw reply related	[flat|nested] 3+ messages in thread

* [PATCH 2/2] ath11k: Add ap power save support
  2020-05-20  6:05 [PATCH 1/2] nl80211: vendor-cmd: qca: add command for ap power save Venkateswara Naralasetty
@ 2020-05-20  6:05 ` Venkateswara Naralasetty
  2020-07-30 11:45 ` [PATCH 1/2] nl80211: vendor-cmd: qca: add command for ap power save Johannes Berg
  1 sibling, 0 replies; 3+ messages in thread
From: Venkateswara Naralasetty @ 2020-05-20  6:05 UTC (permalink / raw)
  To: ath11k; +Cc: linux-wireless, Venkateswara Naralasetty

AP power save where AP goes to power save mode when no stations associate
to it and come out of power save when any station associate to AP.

This AP power save capability can be used to save power with the drawback
of reduced range or delayed discovery of the AP

This patch also porvides user configuration to enable/disable
this feature using vendor command. This feature is disabled by default.

Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1

Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
---
 drivers/net/wireless/ath/ath11k/Makefile |  3 +-
 drivers/net/wireless/ath/ath11k/core.h   |  8 ++++
 drivers/net/wireless/ath/ath11k/mac.c    | 44 +++++++++++++++++
 drivers/net/wireless/ath/ath11k/mac.h    |  1 +
 drivers/net/wireless/ath/ath11k/vendor.c | 81 ++++++++++++++++++++++++++++++++
 drivers/net/wireless/ath/ath11k/vendor.h | 12 +++++
 drivers/net/wireless/ath/ath11k/wmi.c    | 32 +++++++++++++
 drivers/net/wireless/ath/ath11k/wmi.h    |  7 +++
 8 files changed, 187 insertions(+), 1 deletion(-)
 create mode 100644 drivers/net/wireless/ath/ath11k/vendor.c
 create mode 100644 drivers/net/wireless/ath/ath11k/vendor.h

diff --git a/drivers/net/wireless/ath/ath11k/Makefile b/drivers/net/wireless/ath/ath11k/Makefile
index fe7736e..a7e8d00 100644
--- a/drivers/net/wireless/ath/ath11k/Makefile
+++ b/drivers/net/wireless/ath/ath11k/Makefile
@@ -15,7 +15,8 @@ ath11k-y += core.o \
 	    dp_rx.o \
 	    debug.o \
 	    ce.o \
-	    peer.o
+	    peer.o \
+	    vendor.o
 
 ath11k-$(CONFIG_ATH11K_DEBUGFS) += debug_htt_stats.o debugfs_sta.o
 ath11k-$(CONFIG_NL80211_TESTMODE) += testmode.o
diff --git a/drivers/net/wireless/ath/ath11k/core.h b/drivers/net/wireless/ath/ath11k/core.h
index e04f0e7..81cabbd 100644
--- a/drivers/net/wireless/ath/ath11k/core.h
+++ b/drivers/net/wireless/ath/ath11k/core.h
@@ -21,6 +21,7 @@
 #include "hal_rx.h"
 #include "reg.h"
 #include "thermal.h"
+#include "vendor.h"
 
 #define SM(_v, _f) (((_v) << _f##_LSB) & _f##_MASK)
 
@@ -419,6 +420,11 @@ struct ath11k_vdev_stop_status {
 	u32  vdev_id;
 };
 
+enum ath11k_ap_ps_state {
+	ATH11K_AP_PS_STATE_OFF,
+	ATH11K_AP_PS_STATE_ON,
+};
+
 struct ath11k {
 	struct ath11k_base *ab;
 	struct ath11k_pdev *pdev;
@@ -539,6 +545,8 @@ struct ath11k {
 #endif
 	bool dfs_block_radar_events;
 	struct ath11k_thermal thermal;
+	int ap_ps_enabled;
+	enum ath11k_ap_ps_state ap_ps_state;
 };
 
 struct ath11k_band_cap {
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index d9117eb..2cd2e9c 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -2785,6 +2785,33 @@ static void ath11k_mac_dec_num_stations(struct ath11k_vif *arvif,
 	ar->num_stations--;
 }
 
+int ath11k_mac_ap_ps_recalc(struct ath11k *ar)
+{
+	struct ath11k_vif *arvif;
+	bool has_sta_iface = false;
+	enum ath11k_ap_ps_state state = ATH11K_AP_PS_STATE_OFF;
+	int ret = 0;
+
+	list_for_each_entry(arvif, &ar->arvifs, list) {
+		if (arvif->vdev_type == WMI_VDEV_TYPE_STA) {
+			has_sta_iface = true;
+			break;
+		}
+	}
+
+	if (!has_sta_iface && !ar->num_stations && ar->ap_ps_enabled)
+		state = ATH11K_AP_PS_STATE_ON;
+
+	if (ar->ap_ps_state == state)
+		return ret;
+
+	ret = ath11k_wmi_pdev_ap_ps_cmd_send(ar, ar->pdev->pdev_id, state);
+	if (!ret)
+		ar->ap_ps_state = state;
+
+	return ret;
+}
+
 static int ath11k_mac_station_add(struct ath11k *ar,
 				  struct ieee80211_vif *vif,
 				  struct ieee80211_sta *sta)
@@ -2824,6 +2851,12 @@ static int ath11k_mac_station_add(struct ath11k *ar,
 	ath11k_dbg(ab, ATH11K_DBG_MAC, "Added peer: %pM for VDEV: %d\n",
 		   sta->addr, arvif->vdev_id);
 
+	ret = ath11k_mac_ap_ps_recalc(ar);
+	if (ret) {
+		ath11k_warn(ar->ab, "failed to send ap ps ret %d\n", ret);
+		goto exit;
+	}
+
 	if (ath11k_debug_is_extd_tx_stats_enabled(ar)) {
 		arsta->tx_stats = kzalloc(sizeof(*arsta->tx_stats), GFP_KERNEL);
 		if (!arsta->tx_stats) {
@@ -2925,6 +2958,10 @@ static int ath11k_mac_op_sta_state(struct ieee80211_hw *hw,
 
 		kfree(arsta->rx_stats);
 		arsta->rx_stats = NULL;
+
+		ret = ath11k_mac_ap_ps_recalc(ar);
+		if (ret)
+			ath11k_warn(ar->ab, "failed to send ap ps ret %d\n", ret);
 	} else if (old_state == IEEE80211_STA_AUTH &&
 		   new_state == IEEE80211_STA_ASSOC &&
 		   (vif->type == NL80211_IFTYPE_AP ||
@@ -4044,6 +4081,7 @@ static void ath11k_mac_op_stop(struct ieee80211_hw *hw)
 
 	clear_bit(ATH11K_CAC_RUNNING, &ar->dev_flags);
 	ar->state = ATH11K_STATE_OFF;
+	ar->ap_ps_state = ATH11K_AP_PS_STATE_OFF;
 	mutex_unlock(&ar->conf_mutex);
 
 	cancel_delayed_work_sync(&ar->scan.timeout);
@@ -4362,6 +4400,10 @@ static int ath11k_mac_op_add_interface(struct ieee80211_hw *hw,
 
 	ath11k_dp_vdev_tx_attach(ar, arvif);
 
+	ret = ath11k_mac_ap_ps_recalc(ar);
+	if (ret)
+		ath11k_warn(ar->ab, "failed to set ap ps ret %d\n", ret);
+
 	mutex_unlock(&ar->conf_mutex);
 
 	return 0;
@@ -4448,6 +4490,7 @@ static void ath11k_mac_op_remove_interface(struct ieee80211_hw *hw,
 
 	/* Recalc txpower for remaining vdev */
 	ath11k_mac_txpower_recalc(ar);
+	ath11k_mac_ap_ps_recalc(ar);
 	clear_bit(ATH11K_FLAG_MONITOR_ENABLED, &ar->monitor_flags);
 
 	/* TODO: recal traffic pause state based on the available vdevs */
@@ -5908,6 +5951,7 @@ static int __ath11k_mac_register(struct ath11k *ar)
 		ARRAY_SIZE(ath11k_iftypes_ext_capa);
 
 	ath11k_reg_init(ar);
+	ath11k_vendor_register(ar);
 
 	/* advertise HW checksum offload capabilities */
 	ar->hw->netdev_features = NETIF_F_HW_CSUM;
diff --git a/drivers/net/wireless/ath/ath11k/mac.h b/drivers/net/wireless/ath/ath11k/mac.h
index 0607479..18d2f28 100644
--- a/drivers/net/wireless/ath/ath11k/mac.h
+++ b/drivers/net/wireless/ath/ath11k/mac.h
@@ -146,4 +146,5 @@ int ath11k_mac_tx_mgmt_pending_free(int buf_id, void *skb, void *ctx);
 u8 ath11k_mac_bw_to_mac80211_bw(u8 bw);
 enum ath11k_supported_bw ath11k_mac_mac80211_bw_to_ath11k_bw(enum rate_info_bw bw);
 enum hal_encrypt_type ath11k_dp_tx_get_encrypt_type(u32 cipher);
+int ath11k_mac_ap_ps_recalc(struct ath11k *ar);
 #endif
diff --git a/drivers/net/wireless/ath/ath11k/vendor.c b/drivers/net/wireless/ath/ath11k/vendor.c
new file mode 100644
index 0000000..b28cc65
--- /dev/null
+++ b/drivers/net/wireless/ath/ath11k/vendor.c
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: BSD-3-Clause-Clear
+/*
+ * Copyright (c) 2019-2020 The Linux Foundation. All rights reserved.
+ */
+
+#include <net/netlink.h>
+#include <net/mac80211.h>
+#include <uapi/nl80211-vnd-qca.h>
+#include "core.h"
+#include "debug.h"
+
+static const struct nla_policy
+ath11k_vendor_set_wifi_config_policy[QCA_WLAN_VENDOR_ATTR_CONFIG_MAX + 1] = {
+	[QCA_WLAN_VENDOR_ATTR_CONFIG_GTX] = {.type = NLA_FLAG}
+};
+
+static int ath11k_vendor_set_wifi_config(struct wiphy *wihpy,
+					 struct wireless_dev *wdev,
+					 const void *data,
+					 int data_len)
+{
+	struct ieee80211_vif *vif;
+	struct ath11k_vif *arvif;
+	struct ath11k *ar;
+	struct nlattr *tb[QCA_WLAN_VENDOR_ATTR_CONFIG_MAX + 1];
+	int ret = 0;
+
+	if (!wdev)
+		return -EINVAL;
+
+	vif = wdev_to_ieee80211_vif(wdev);
+	if (!vif)
+		return -EINVAL;
+
+	arvif = (struct ath11k_vif *)vif->drv_priv;
+	if (!arvif)
+		return -EINVAL;
+
+	ar = arvif->ar;
+
+	mutex_lock(&ar->conf_mutex);
+
+	ret = nla_parse(tb, QCA_WLAN_VENDOR_ATTR_CONFIG_MAX, data, data_len,
+			ath11k_vendor_set_wifi_config_policy, NULL);
+	if (ret) {
+		ath11k_warn(ar->ab, "invalid set wifi config policy attribute\n");
+		goto exit;
+	}
+
+	ar->ap_ps_enabled = nla_get_flag(tb[QCA_WLAN_VENDOR_ATTR_CONFIG_GTX]);
+	ret = ath11k_mac_ap_ps_recalc(ar);
+	if (ret) {
+		ath11k_warn(ar->ab, "failed to send ap ps ret %d\n", ret);
+		goto exit;
+	}
+
+exit:
+	mutex_unlock(&ar->conf_mutex);
+	return ret;
+}
+
+static struct wiphy_vendor_command ath11k_vendor_commands[] = {
+	{
+		.info.vendor_id = QCA_NL80211_VENDOR_ID,
+		.info.subcmd = QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION,
+		.flags = WIPHY_VENDOR_CMD_NEED_WDEV |
+			WIPHY_VENDOR_CMD_NEED_RUNNING,
+		.doit = ath11k_vendor_set_wifi_config,
+		.policy = ath11k_vendor_set_wifi_config_policy,
+		.maxattr = QCA_WLAN_VENDOR_ATTR_CONFIG_MAX
+	}
+};
+
+int ath11k_vendor_register(struct ath11k *ar)
+{
+	ar->hw->wiphy->vendor_commands = ath11k_vendor_commands;
+	ar->hw->wiphy->n_vendor_commands = ARRAY_SIZE(ath11k_vendor_commands);
+
+	return 0;
+}
+
diff --git a/drivers/net/wireless/ath/ath11k/vendor.h b/drivers/net/wireless/ath/ath11k/vendor.h
new file mode 100644
index 0000000..6eaf07e
--- /dev/null
+++ b/drivers/net/wireless/ath/ath11k/vendor.h
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: BSD-3-Clause-Clear
+/*
+ * Copyright (c) 2019-2020 The Linux Foundation. All rights reserved.
+ */
+
+#ifndef ATH11K_VENDOR_H
+#define ATH11K_VENDOR_H
+
+int ath11k_vendor_register(struct ath11k *ar);
+
+#endif /* QCA_VENDOR_H */
+
diff --git a/drivers/net/wireless/ath/ath11k/wmi.c b/drivers/net/wireless/ath/ath11k/wmi.c
index c2a9723..71fff34 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.c
+++ b/drivers/net/wireless/ath/ath11k/wmi.c
@@ -1146,6 +1146,38 @@ ath11k_wmi_rx_reord_queue_remove(struct ath11k *ar,
 	return ret;
 }
 
+int ath11k_wmi_pdev_ap_ps_cmd_send(struct ath11k *ar, u8 pdev_id,
+				   u32 param_value)
+{
+	struct ath11k_pdev_wmi *wmi = ar->wmi;
+	struct wmi_pdev_ap_ps_cmd *cmd;
+	struct sk_buff *skb;
+	int ret;
+
+	skb = ath11k_wmi_alloc_skb(wmi->wmi_ab, sizeof(*cmd));
+	if (!skb)
+		return -ENOMEM;
+
+	cmd = (struct wmi_pdev_ap_ps_cmd *)skb->data;
+	cmd->tlv_header = FIELD_PREP(WMI_TLV_TAG,
+				     WMI_TAG_PDEV_GREEN_AP_PS_ENABLE_CMD) |
+			  FIELD_PREP(WMI_TLV_LEN, sizeof(*cmd) - TLV_HDR_SIZE);
+	cmd->pdev_id = pdev_id;
+	cmd->param_value = param_value;
+
+	ret = ath11k_wmi_cmd_send(wmi, skb, WMI_PDEV_GREEN_AP_PS_ENABLE_CMDID);
+	if (ret) {
+		ath11k_warn(ar->ab, "failed to send ap ps enable/disable cmd\n");
+		dev_kfree_skb(skb);
+	}
+
+	ath11k_dbg(ar->ab, ATH11K_DBG_WMI,
+		   "wmi pdev ap ps set pdev id %d value %d\n",
+		   pdev_id, param_value);
+
+	return ret;
+}
+
 int ath11k_wmi_pdev_set_param(struct ath11k *ar, u32 param_id,
 			      u32 param_value, u8 pdev_id)
 {
diff --git a/drivers/net/wireless/ath/ath11k/wmi.h b/drivers/net/wireless/ath/ath11k/wmi.h
index b9f3e55..1ef6c67 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.h
+++ b/drivers/net/wireless/ath/ath11k/wmi.h
@@ -2864,6 +2864,12 @@ struct set_fwtest_params {
 	u32 value;
 };
 
+struct wmi_pdev_ap_ps_cmd {
+	u32 tlv_header;
+	u32 pdev_id;
+	u32 param_value;
+} __packed;
+
 struct wmi_fwtest_set_param_cmd_param {
 	u32 tlv_header;
 	u32 param_id;
@@ -4941,4 +4947,5 @@ int ath11k_wmi_send_obss_color_collision_cfg_cmd(struct ath11k *ar, u32 vdev_id,
 int ath11k_wmi_send_bss_color_change_enable_cmd(struct ath11k *ar, u32 vdev_id,
 						bool enable);
 int ath11k_wmi_pdev_lro_cfg(struct ath11k *ar, int pdev_id);
+int ath11k_wmi_pdev_ap_ps_cmd_send(struct ath11k *ar, u8 pdev_id, u32 value);
 #endif
-- 
2.7.4


^ permalink raw reply related	[flat|nested] 3+ messages in thread

* Re: [PATCH 1/2] nl80211: vendor-cmd: qca: add command for ap power save
  2020-05-20  6:05 [PATCH 1/2] nl80211: vendor-cmd: qca: add command for ap power save Venkateswara Naralasetty
  2020-05-20  6:05 ` [PATCH 2/2] ath11k: Add ap power save support Venkateswara Naralasetty
@ 2020-07-30 11:45 ` Johannes Berg
  1 sibling, 0 replies; 3+ messages in thread
From: Johannes Berg @ 2020-07-30 11:45 UTC (permalink / raw)
  To: Venkateswara Naralasetty, ath11k; +Cc: linux-wireless

On Wed, 2020-05-20 at 11:35 +0530, Venkateswara Naralasetty wrote:
> This patch is to add vendor command support to enable/disable
> ap power save.
> 
> An example of usage: iw dev wlanx vendor send 0x1374 0x4a ap-ps <val>
> 
> 0x1374: vendor id
> 0x4a: vendor subcmd id
> val: 0 - disable power save
>      1 - enable power save

This really doesn't pass the bar ...

https://wireless.wiki.kernel.org/en/developers/documentation/nl80211#vendor-specific_api

johannes


^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2020-07-30 11:45 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-05-20  6:05 [PATCH 1/2] nl80211: vendor-cmd: qca: add command for ap power save Venkateswara Naralasetty
2020-05-20  6:05 ` [PATCH 2/2] ath11k: Add ap power save support Venkateswara Naralasetty
2020-07-30 11:45 ` [PATCH 1/2] nl80211: vendor-cmd: qca: add command for ap power save Johannes Berg

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).