From: Malthe Borch <mborch@gmail.com>
To: linux-wireless@vger.kernel.org
Subject: Intel Wireless: Microcode SW error detected.
Date: Mon, 26 Jul 2010 17:19:18 -0400 [thread overview]
Message-ID: <AANLkTimrv507n5-WmikUOhPE95wM1p1_Qtd65rOA1hei@mail.gmail.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 150 bytes --]
I get this with the latest and greatest Intel firmware 9.221.4.1 build 25532.
Ultimately enabling the device fails with: "uCode did not respond OK."
[-- Attachment #2: dmesg --]
[-- Type: application/octet-stream, Size: 3233 bytes --]
[ 35.882305] iwlagn 0000:02:00.0: Microcode SW error detected. Restarting 0x82000000.
[ 35.882313] iwlagn 0000:02:00.0: Loaded firmware version: 9.221.4.1 build 25532
[ 35.882318] iwlagn 0000:02:00.0: Not valid error log pointer 0x00000000 for RT uCode
[ 35.882322] iwlagn 0000:02:00.0: CSR values:
[ 35.882325] iwlagn 0000:02:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG)
[ 35.882333] iwlagn 0000:02:00.0: CSR_HW_IF_CONFIG_REG: 0X00480303
[ 35.882339] iwlagn 0000:02:00.0: CSR_INT_COALESCING: 0X00000040
[ 35.882346] iwlagn 0000:02:00.0: CSR_INT: 0X80000000
[ 35.882353] iwlagn 0000:02:00.0: CSR_INT_MASK: 0X00000000
[ 35.882359] iwlagn 0000:02:00.0: CSR_FH_INT_STATUS: 0X40010000
[ 35.882365] iwlagn 0000:02:00.0: CSR_GPIO_IN: 0X0000000f
[ 35.882371] iwlagn 0000:02:00.0: CSR_RESET: 0X00000000
[ 35.882377] iwlagn 0000:02:00.0: CSR_GP_CNTRL: 0X080403c5
[ 35.882383] iwlagn 0000:02:00.0: CSR_HW_REV: 0X00000074
[ 35.882389] iwlagn 0000:02:00.0: CSR_EEPROM_REG: 0X00000000
[ 35.882396] iwlagn 0000:02:00.0: CSR_EEPROM_GP: 0X90000004
[ 35.882403] iwlagn 0000:02:00.0: CSR_OTP_GP_REG: 0X00020000
[ 35.882408] iwlagn 0000:02:00.0: CSR_GIO_REG: 0X00080046
[ 35.882415] iwlagn 0000:02:00.0: CSR_GP_UCODE_REG: 0X00000000
[ 35.882421] iwlagn 0000:02:00.0: CSR_GP_DRIVER_REG: 0X00000000
[ 35.882427] iwlagn 0000:02:00.0: CSR_UCODE_DRV_GP1: 0X00000000
[ 35.882433] iwlagn 0000:02:00.0: CSR_UCODE_DRV_GP2: 0X00000000
[ 35.882439] iwlagn 0000:02:00.0: CSR_LED_REG: 0X00000018
[ 35.882446] iwlagn 0000:02:00.0: CSR_DRAM_INT_TBL_REG: 0X00000000
[ 35.882452] iwlagn 0000:02:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200
[ 35.882458] iwlagn 0000:02:00.0: CSR_ANA_PLL_CFG: 0X00000000
[ 35.882466] iwlagn 0000:02:00.0: CSR_HW_REV_WA_REG: 0X0001001a
[ 35.882470] iwlagn 0000:02:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0000
[ 35.882472] iwlagn 0000:02:00.0: FH register values:
[ 35.882484] iwlagn 0000:02:00.0: FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X0259b200
[ 35.882497] iwlagn 0000:02:00.0: FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X00259b50
[ 35.882510] iwlagn 0000:02:00.0: FH_RSCSR_CHNL0_WPTR: 0X000000f8
[ 35.882523] iwlagn 0000:02:00.0: FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104
[ 35.882535] iwlagn 0000:02:00.0: FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc
[ 35.882548] iwlagn 0000:02:00.0: FH_MEM_RSSR_RX_STATUS_REG: 0X07030000
[ 35.882560] iwlagn 0000:02:00.0: FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
[ 35.882573] iwlagn 0000:02:00.0: FH_TSSR_TX_STATUS_REG: 0X07ff0001
[ 35.882586] iwlagn 0000:02:00.0: FH_TSSR_TX_ERROR_REG: 0X00000000
[ 35.882588] iwlagn 0000:02:00.0: Invalid event log pointer 0x00000000 for RT uCode
[ 35.882594] iwlagn 0000:02:00.0: uCode did not respond OK.
[ 37.381061] eth0: no IPv6 routers present
[ 39.848203] iwlagn 0000:02:00.0: START_ALIVE timeout after 4000ms.
next reply other threads:[~2010-07-26 21:19 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-07-26 21:19 Malthe Borch [this message]
2010-07-27 14:40 ` Intel Wireless: Microcode SW error detected Guy, Wey-Yi W
2010-08-01 23:56 ` Malthe Borch
2010-08-26 11:46 ` Saurav Barik
2010-08-26 15:48 ` Guy, Wey-Yi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=AANLkTimrv507n5-WmikUOhPE95wM1p1_Qtd65rOA1hei@mail.gmail.com \
--to=mborch@gmail.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).