linux-wireless.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Equipe Soft <equipe.soft.isere@gmail.com>
To: linux-wireless@vger.kernel.org
Subject: Issue with intel wireless-AC 9260 in wifi direct in 5Ghz
Date: Wed, 28 Aug 2019 19:21:24 +0200	[thread overview]
Message-ID: <CAFb4eQksH4B8fO8kShaLSPk+-tNsE3tdUHb7qbXXSneSwjt9QA@mail.gmail.com> (raw)

Hello,
I'm trying to set up a wifi direct group between my AC9260 wifi board
and a android tablet supporting WifiDirect.

I tried several configurations and I faced some issues.
Here follow the testing sequence. All the following command are sent
through wpa_cli:

> p2p_find
P2P-DEVICE-FOUND f2:ee:10:c2:ce:68 p2p_dev_addr=f2:ee:10:c2:ce:68
pri_dev_type=10-0050F204-5 name='[Tablet] Galaxy Tab S3'
config_methods=0x188 dev_capab=0x25 group_capab=0x0 vendor_elems=1
new=1

>p2p_connect f2:ee:10:c2:ce:68 pin 1234 go_intent=1
74493685

PIN is set on the tablet then, on my terminal I see:

P2P-GO-NEG-SUCCESS role=GO freq=5785 ht40=0 peer_dev=f2:ee:10:c2:ce:68
peer_iface=f2:ee:10:c2:4e:68 wps_method=Display
P2P-GROUP-FORMATION-FAILURE
P2P-GROUP-REMOVED p2p-wlan0-0 GO reason=FORMATION_FAILED

dmesg :

[ 1875.593069] IPv6: ADDRCONF(NETDEV_UP): p2p-wlan0-0: link is not ready
[ 1875.659199] iwlwifi 0000:01:00.0: Microcode SW error detected.
Restarting 0x2000000.
[ 1875.667246] iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
[ 1875.672851] iwlwifi 0000:01:00.0: Status: 0x00000100, count: 6
[ 1875.678718] iwlwifi 0000:01:00.0: Loaded firmware version: 38.755cfdd8.0
[ 1875.685466] iwlwifi 0000:01:00.0: 0x000014FC | ADVANCED_SYSASSERT
[ 1875.692498] iwlwifi 0000:01:00.0: 0x00A0A200 | trm_hw_status0
[ 1875.698270] iwlwifi 0000:01:00.0: 0x00000000 | trm_hw_status1
[ 1875.704048] iwlwifi 0000:01:00.0: 0x00454EF6 | branchlink2
[ 1875.709561] iwlwifi 0000:01:00.0: 0x0045E90E | interruptlink1
[ 1875.715330] iwlwifi 0000:01:00.0: 0x00000000 | interruptlink2
[ 1875.721096] iwlwifi 0000:01:00.0: 0x00009D00 | data1
[ 1875.726084] iwlwifi 0000:01:00.0: 0x00000741 | data2
[ 1875.731070] iwlwifi 0000:01:00.0: 0x00090010 | data3
[ 1875.736076] iwlwifi 0000:01:00.0: 0x00000000 | beacon time
[ 1875.741589] iwlwifi 0000:01:00.0: 0x6F091C80 | tsf low
[ 1875.746757] iwlwifi 0000:01:00.0: 0x00000000 | tsf hi
[ 1875.751833] iwlwifi 0000:01:00.0: 0x00000000 | time gp1
[ 1875.757081] iwlwifi 0000:01:00.0: 0x6F091C81 | time gp2
[ 1875.762325] iwlwifi 0000:01:00.0: 0x00000001 | uCode revision type
[ 1875.768529] iwlwifi 0000:01:00.0: 0x00000026 | uCode version major
[ 1875.774731] iwlwifi 0000:01:00.0: 0x755CFDD8 | uCode version minor
[ 1875.780934] iwlwifi 0000:01:00.0: 0x00000321 | hw version
[ 1875.786352] iwlwifi 0000:01:00.0: 0x00C89004 | board version
[ 1875.792044] iwlwifi 0000:01:00.0: 0x801BF402 | hcmd
[ 1875.796951] iwlwifi 0000:01:00.0: 0x24022000 | isr0
[ 1875.801853] iwlwifi 0000:01:00.0: 0x01000000 | isr1
[ 1875.806751] iwlwifi 0000:01:00.0: 0x08301802 | isr2
[ 1875.811653] iwlwifi 0000:01:00.0: 0x00415CC0 | isr3
[ 1875.816559] iwlwifi 0000:01:00.0: 0x00000000 | isr4
[ 1875.821462] iwlwifi 0000:01:00.0: 0x000501D1 | last cmd Id
[ 1875.826975] iwlwifi 0000:01:00.0: 0x00000000 | wait_event
[ 1875.832399] iwlwifi 0000:01:00.0: 0x000000D0 | l2p_control
[ 1875.837928] iwlwifi 0000:01:00.0: 0x00018014 | l2p_duration
[ 1875.843527] iwlwifi 0000:01:00.0: 0x0000003F | l2p_mhvalid
[ 1875.849040] iwlwifi 0000:01:00.0: 0x00000000 | l2p_addr_match
[ 1875.854811] iwlwifi 0000:01:00.0: 0x0000000D | lmpm_pmg_sel
[ 1875.860412] iwlwifi 0000:01:00.0: 0x04071046 | timestamp
[ 1875.865758] iwlwifi 0000:01:00.0: 0x0000C0E4 | flow_handler
[ 1875.871405] iwlwifi 0000:01:00.0: Start IWL Error Log Dump:
[ 1875.877037] iwlwifi 0000:01:00.0: Status: 0x00000100, count: 7
[ 1875.882889] iwlwifi 0000:01:00.0: 0x00000070 | ADVANCED_SYSASSERT
[ 1875.889020] iwlwifi 0000:01:00.0: 0x00000000 | umac branchlink1
[ 1875.894959] iwlwifi 0000:01:00.0: 0xC0087CB8 | umac branchlink2
[ 1875.900904] iwlwifi 0000:01:00.0: 0xC0084264 | umac interruptlink1
[ 1875.907134] iwlwifi 0000:01:00.0: 0xC00847C8 | umac interruptlink2
[ 1875.913344] iwlwifi 0000:01:00.0: 0x00000800 | umac data1
[ 1875.918764] iwlwifi 0000:01:00.0: 0xC00847C8 | umac data2
[ 1875.924184] iwlwifi 0000:01:00.0: 0xDEADBEEF | umac data3
[ 1875.929606] iwlwifi 0000:01:00.0: 0x00000026 | umac major
[ 1875.935026] iwlwifi 0000:01:00.0: 0x755CFDD8 | umac minor
[ 1875.940448] iwlwifi 0000:01:00.0: 0xC0887F30 | frame pointer
[ 1875.946128] iwlwifi 0000:01:00.0: 0xC0887F30 | stack pointer
[ 1875.951810] iwlwifi 0000:01:00.0: 0x0006012B | last host cmd
[ 1875.957488] iwlwifi 0000:01:00.0: 0x00000000 | isr status reg
[ 1875.963268] ieee80211 phy0: Hardware restart was requested
[ 1875.968932] iwlwifi 0000:01:00.0: iwlwifi transaction failed,
dumping registers
[ 1875.976275] iwlwifi 0000:01:00.0: iwlwifi device config registers:
[ 1875.983647] iwlwifi 0000:01:00.0: 00000000: 25268086 00100406
02800029 00000000 e0000004 00000000 00000000 00000000
[ 1875.994312] iwlwifi 0000:01:00.0: 00000020: 00000000 00000000
00000000 00148086 00000000 000000c8 00000000 0000012b
[ 1876.004835] iwlwifi 0000:01:00.0: iwlwifi device memory mapped registers:
[ 1876.011780] iwlwifi 0000:01:00.0: 00000000: 00c89004 00000040
00000000 ba00008b 00000000 00000000 00027e1f 00000000
[ 1876.022251] iwlwifi 0000:01:00.0: 00000020: 00000000 0c040005
00000321 d55555d5 d55555d5 d55555d5 80008040 041f0044
[ 1876.032714] iwlwifi 0000:01:00.0: iwlwifi device AER capability structure:
[ 1876.039694] iwlwifi 0000:01:00.0: 00000000: 14c10001 00000000
00000000 00462031 00000000 00002000 00000000 00000000
[ 1876.050219] iwlwifi 0000:01:00.0: 00000020: 00000000 00000000 00000000
[ 1876.056838] iwlwifi 0000:01:00.0: iwlwifi parent port
(0000:00:00.0) config registers:
[ 1876.064933] iwlwifi 0000:00:00.0: 00000000: d02110ee 00100006
06040000 00010000 00000000 00000000 000c0100 00000000
[ 1876.075399] iwlwifi 0000:00:00.0: 00000020: e000e000 0001fff1
00000000 00000000 00000000 00000040 00000000 0000012b
[ 1876.085869] iwlwifi 0000:01:00.0: FW error in SYNC CMD BINDING_CONTEXT_CMD
[ 1876.092773] CPU: 1 PID: 498 Comm: wpa_supplicant Not tainted
4.18.31-yocto-standard #1
[ 1876.100680] Hardware name: ********
[ 1876.105290] Call trace:
[ 1876.107744]  dump_backtrace+0x0/0x158
[ 1876.111403]  show_stack+0x24/0x30
[ 1876.114723]  dump_stack+0x80/0xa4
[ 1876.118064]  iwl_trans_pcie_send_hcmd+0x5d0/0x5e8 [iwlwifi]
[ 1876.123649]  iwl_trans_send_cmd+0x68/0x108 [iwlwifi]
[ 1876.128644]  iwl_mvm_send_cmd_status+0x44/0xe0 [iwlmvm]
[ 1876.133889]  iwl_mvm_send_cmd_pdu_status+0x6c/0x98 [iwlmvm]
[ 1876.139480]  iwl_mvm_binding_update+0x148/0x230 [iwlmvm]
[ 1876.144809]  iwl_mvm_binding_add_vif+0x5c/0x80 [iwlmvm]
[ 1876.150048]  iwl_mvm_start_ap_ibss+0xe0/0x238 [iwlmvm]
[ 1876.155268]  ieee80211_start_ap+0x218/0x488 [mac80211]
[ 1876.160473]  nl80211_start_ap+0x3f4/0x6a8 [cfg80211]
[ 1876.165446]  genl_family_rcv_msg+0x1cc/0x338
[ 1876.169718]  genl_rcv_msg+0xa0/0xd8
[ 1876.173207]  netlink_rcv_skb+0x60/0x120
[ 1876.177043]  genl_rcv+0x3c/0x50
[ 1876.180186]  netlink_unicast+0x194/0x210
[ 1876.184109]  netlink_sendmsg+0x1a0/0x348
[ 1876.188036]  sock_sendmsg+0x34/0x50
[ 1876.191523]  ___sys_sendmsg+0x288/0x2c8
[ 1876.195357]  __sys_sendmsg+0x7c/0xd0
[ 1876.198933]  sys_sendmsg+0x38/0x48
[ 1876.202330]  el0_svc_naked+0x30/0x34
[ 1876.206366] iwlwifi 0000:01:00.0: Failed to send binding (action:1): -5
[ 1876.213092] iwlwifi 0000:01:00.0: Failed to remove MAC context: -5
[ 1876.219353] iwlwifi 0000:01:00.0: PHY ctxt cmd error. ret=-5

It looks like the module firmware got an error when trying to set the
module in AP in 5GHz. I know there could be some regulatory limitation
for IBSS in 5Ghz, but why this does not work for wifi direct.
Thanks for your time.
@team.

             reply	other threads:[~2019-08-28 17:21 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-08-28 17:21 Equipe Soft [this message]
2019-09-04  7:19 ` Issue with intel wireless-AC 9260 in wifi direct in 5Ghz Equipe Soft

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=CAFb4eQksH4B8fO8kShaLSPk+-tNsE3tdUHb7qbXXSneSwjt9QA@mail.gmail.com \
    --to=equipe.soft.isere@gmail.com \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).