From: Andy Shevchenko <andy.shevchenko@gmail.com>
To: "Jonas Dreßler" <verdre@v0yd.nl>
Cc: "Amitkumar Karwar" <amitkarwar@gmail.com>,
"Ganapathi Bhat" <ganapathi017@gmail.com>,
"Xinming Hu" <huxinming820@gmail.com>,
"Kalle Valo" <kvalo@codeaurora.org>,
"David S. Miller" <davem@davemloft.net>,
"Jakub Kicinski" <kuba@kernel.org>,
"Tsuchiya Yuto" <kitakar@gmail.com>,
"open list:TI WILINK WIRELES..." <linux-wireless@vger.kernel.org>,
netdev <netdev@vger.kernel.org>,
"Linux Kernel Mailing List" <linux-kernel@vger.kernel.org>,
linux-pci <linux-pci@vger.kernel.org>,
"Maximilian Luz" <luzmaximilian@gmail.com>,
"Andy Shevchenko" <andriy.shevchenko@linux.intel.com>,
"Bjorn Helgaas" <bhelgaas@google.com>,
"Pali Rohár" <pali@kernel.org>
Subject: Re: [PATCH 1/2] mwifiex: Use non-posted PCI register writes
Date: Mon, 30 Aug 2021 15:49:09 +0300 [thread overview]
Message-ID: <CAHp75VeAKs=nFw4E20etKc3C_Cszyz9AqN=mLsum7F-BdVK5Rg@mail.gmail.com> (raw)
In-Reply-To: <20210830123704.221494-2-verdre@v0yd.nl>
On Mon, Aug 30, 2021 at 3:38 PM Jonas Dreßler <verdre@v0yd.nl> wrote:
>
> On the 88W8897 card it's very important the TX ring write pointer is
> updated correctly to its new value before setting the TX ready
> interrupt, otherwise the firmware appears to crash (probably because
> it's trying to DMA-read from the wrong place).
>
> Since PCI uses "posted writes" when writing to a register, it's not
> guaranteed that a write will happen immediately. That means the pointer
> might be outdated when setting the TX ready interrupt, leading to
> firmware crashes especially when ASPM L1 and L1 substates are enabled
> (because of the higher link latency, the write will probably take
> longer).
>
> So fix those firmware crashes by always forcing non-posted writes. We do
> that by simply reading back the register after writing it, just as a lot
> of other drivers do.
>
> There are two reproducers that are fixed with this patch:
>
> 1) During rx/tx traffic and with ASPM L1 substates enabled (the enabled
> substates are platform dependent), the firmware crashes and eventually a
> command timeout appears in the logs. That crash is fixed by using a
> non-posted write in mwifiex_pcie_send_data().
>
> 2) When sending lots of commands to the card, waking it up from sleep in
> very quick intervals, the firmware eventually crashes. That crash
> appears to be fixed by some other non-posted write included here.
Thanks for all this work!
Nevertheless, do we have any commits that may be a good candidate to
be in the Fixes tag here?
> Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
> ---
> drivers/net/wireless/marvell/mwifiex/pcie.c | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/drivers/net/wireless/marvell/mwifiex/pcie.c b/drivers/net/wireless/marvell/mwifiex/pcie.c
> index c6ccce426b49..bfd6e135ed99 100644
> --- a/drivers/net/wireless/marvell/mwifiex/pcie.c
> +++ b/drivers/net/wireless/marvell/mwifiex/pcie.c
> @@ -237,6 +237,12 @@ static int mwifiex_write_reg(struct mwifiex_adapter *adapter, int reg, u32 data)
>
> iowrite32(data, card->pci_mmap1 + reg);
>
> + /* Do a read-back, which makes the write non-posted, ensuring the
> + * completion before returning.
> + * The firmware of the 88W8897 card is buggy and this avoids crashes.
Any firmware version reference? Would be nice to have just for the
sake of record.
> + */
> + ioread32(card->pci_mmap1 + reg);
> +
> return 0;
> }
--
With Best Regards,
Andy Shevchenko
next prev parent reply other threads:[~2021-08-30 12:49 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-30 12:37 [PATCH 0/2] mwifiex: Work around firmware bugs on 88W8897 chip Jonas Dreßler
2021-08-30 12:37 ` [PATCH 1/2] mwifiex: Use non-posted PCI register writes Jonas Dreßler
2021-08-30 12:49 ` Andy Shevchenko [this message]
2021-09-01 14:01 ` Jonas Dreßler
2021-09-01 15:47 ` Andy Shevchenko
2021-09-01 15:51 ` Pali Rohár
2021-09-01 16:51 ` Heiner Kallweit
2021-09-01 17:07 ` Johannes Berg
2021-09-01 19:07 ` Heiner Kallweit
2021-09-01 22:41 ` Bjorn Helgaas
2021-09-02 14:05 ` Bjorn Helgaas
2021-09-01 19:40 ` Brian Norris
2021-09-01 20:40 ` Andy Shevchenko
2021-09-01 21:04 ` Brian Norris
2021-09-01 21:07 ` Brian Norris
2021-09-18 7:37 ` Jonas Dreßler
2021-09-20 17:48 ` Brian Norris
2021-09-22 12:50 ` Jonas Dreßler
2021-09-23 15:28 ` Jonas Dreßler
2021-09-23 19:37 ` Andy Shevchenko
2021-09-23 19:41 ` Andy Shevchenko
2021-09-23 20:22 ` Pali Rohár
2021-09-30 15:38 ` Jonas Dreßler
2021-09-30 15:42 ` Pali Rohár
2021-09-30 16:14 ` Jonas Dreßler
2021-09-30 16:19 ` Pali Rohár
2021-09-30 16:22 ` Jonas Dreßler
2021-09-30 16:39 ` Pali Rohár
2021-08-30 12:37 ` [PATCH 2/2] mwifiex: Try waking the firmware until we get an interrupt Jonas Dreßler
2021-08-30 12:51 ` Andy Shevchenko
2021-08-30 12:55 ` Andy Shevchenko
2021-09-25 17:32 ` [PATCH 0/2] mwifiex: Work around firmware bugs on 88W8897 chip Pali Rohár
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAHp75VeAKs=nFw4E20etKc3C_Cszyz9AqN=mLsum7F-BdVK5Rg@mail.gmail.com' \
--to=andy.shevchenko@gmail.com \
--cc=amitkarwar@gmail.com \
--cc=andriy.shevchenko@linux.intel.com \
--cc=bhelgaas@google.com \
--cc=davem@davemloft.net \
--cc=ganapathi017@gmail.com \
--cc=huxinming820@gmail.com \
--cc=kitakar@gmail.com \
--cc=kuba@kernel.org \
--cc=kvalo@codeaurora.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=luzmaximilian@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=pali@kernel.org \
--cc=verdre@v0yd.nl \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).