From: Anatolij Gustschin <agust@denx.de>
To: linuxppc-dev@ozlabs.org
Cc: Anatolij Gustschin <agust@denx.de>,
wd@denx.de, dzu@denx.de, Piotr Ziecik <kosmo@semihalf.com>
Subject: [PATCH 7/8 v2] powerpc/mpc5121: update mpc5121ads DTS
Date: Wed, 27 Jan 2010 13:07:31 +0100 [thread overview]
Message-ID: <1264594052-20317-8-git-send-email-agust@denx.de> (raw)
In-Reply-To: <1264594052-20317-1-git-send-email-agust@denx.de>
Collects several changes needed after applying
previous mpc5121 platform and driver patches:
- Add mpc5121 reset module node
- Clean up and fix NAND description, remove unused properties
here and correct NAND flash chip size.
- Clean up I2C nodes: remove obsolete "cell-index" properties,
add "fsl,preserve-clocking" property
- Add I2C RTC node for m41t61 RTC
- Add I2C nodes for AD7414 temperature sensor and AT24C32CD3 EEPROM
- Fix compatible property in DMA node
- Clean up CAN nodes, remove unused "cell-index" properties
- Fix compatible property in DIU node
- USB node changes:
- remove "port0" and "port1" properties as these are only used
for multi-port host(MHP) module which is not available
on MPC5121.
- MPC5121 Rev 2.0 EHCI registers are big endian.
'fsl,big-endian-regs' property in USB node indicates
this now.
- use 'fsl,invert-drvvbus' and 'fsl,invert-pwr-fault' in
USB node for internal PHY to specify polarities
of the appropriate port pins.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
---
Changes since v1:
- move RTC node for m41t61 RTC to the node for I2C0
- add nodes for AD74114 and AT24C32CD3 devices
- remove obsolete "cell-index" properties from i2c nodes
and add "fsl,preserve-clocking" property
- Clean up CAN nodes
- prefix USB properties with 'fsl,'
arch/powerpc/boot/dts/mpc5121ads.dts | 53 +++++++++++++++++++++-------------
1 files changed, 33 insertions(+), 20 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc5121ads.dts b/arch/powerpc/boot/dts/mpc5121ads.dts
index c353dac..9c5b3b4 100644
--- a/arch/powerpc/boot/dts/mpc5121ads.dts
+++ b/arch/powerpc/boot/dts/mpc5121ads.dts
@@ -62,17 +62,12 @@
interrupt-parent = < &ipic >;
#address-cells = <1>;
#size-cells = <1>;
- bank-width = <1>;
// ADS has two Hynix 512MB Nand flash chips in a single
- // stacked package .
+ // stacked package.
chips = <2>;
- nand0@0 {
- label = "nand0";
- reg = <0x00000000 0x02000000>; // first 32 MB of chip 0
- };
- nand1@20000000 {
- label = "nand1";
- reg = <0x20000000 0x02000000>; // first 32 MB of chip 1
+ nand@0 {
+ label = "nand";
+ reg = <0x00000000 0x40000000>; // 512MB + 512MB
};
};
@@ -166,6 +161,11 @@
interrupt-parent = < &ipic >;
};
+ reset@e00 { // Reset module
+ compatible = "fsl,mpc5121-reset";
+ reg = <0xe00 0x100>;
+ };
+
clock@f00 { // Clock control
compatible = "fsl,mpc5121-clock";
reg = <0xf00 0x100>;
@@ -185,17 +185,15 @@
interrupt-parent = < &ipic >;
};
- mscan@1300 {
+ can@1300 {
compatible = "fsl,mpc5121-mscan";
- cell-index = <0>;
interrupts = <12 0x8>;
interrupt-parent = < &ipic >;
reg = <0x1300 0x80>;
};
- mscan@1380 {
+ can@1380 {
compatible = "fsl,mpc5121-mscan";
- cell-index = <1>;
interrupts = <13 0x8>;
interrupt-parent = < &ipic >;
reg = <0x1380 0x80>;
@@ -205,17 +203,31 @@
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- cell-index = <0>;
reg = <0x1700 0x20>;
interrupts = <9 0x8>;
interrupt-parent = < &ipic >;
+ fsl,preserve-clocking;
+
+ hwmon@4a {
+ compatible = "adi,ad7414";
+ reg = <0x4a>;
+ };
+
+ eeprom@50 {
+ compatible = "at,24c32";
+ reg = <0x50>;
+ };
+
+ rtc@68 {
+ compatible = "stm,m41t62";
+ reg = <0x68>;
+ };
};
i2c@1720 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- cell-index = <1>;
reg = <0x1720 0x20>;
interrupts = <10 0x8>;
interrupt-parent = < &ipic >;
@@ -225,7 +237,6 @@
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- cell-index = <2>;
reg = <0x1740 0x20>;
interrupts = <11 0x8>;
interrupt-parent = < &ipic >;
@@ -244,7 +255,7 @@
};
display@2100 {
- compatible = "fsl,mpc5121-diu", "fsl-diu";
+ compatible = "fsl,mpc5121-diu", "fsl,diu";
reg = <0x2100 0x100>;
interrupts = <64 0x8>;
interrupt-parent = < &ipic >;
@@ -285,7 +296,7 @@
// interrupts = <43 0x8>;
// dr_mode = "otg";
// phy_type = "ulpi";
- // port1;
+ // fsl,big-endian-regs;
//};
// USB0 using internal UTMI PHY
@@ -298,7 +309,9 @@
interrupts = <44 0x8>;
dr_mode = "otg";
phy_type = "utmi_wide";
- port0;
+ fsl,big-endian-regs;
+ fsl,invert-drvvbus;
+ fsl,invert-pwr-fault;
};
// IO control
@@ -365,7 +378,7 @@
};
dma@14000 {
- compatible = "fsl,mpc5121-dma2";
+ compatible = "fsl,mpc5121-dma";
reg = <0x14000 0x1800>;
interrupts = <65 0x8>;
interrupt-parent = < &ipic >;
--
1.5.6.3
next prev parent reply other threads:[~2010-01-27 12:07 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-01-27 12:07 [PATCH 0/8] Update support for MPC512x Anatolij Gustschin
2010-01-27 12:07 ` [PATCH 1/8 v2] powerpc/mpc5121: Add machine restart support Anatolij Gustschin
2010-01-27 15:46 ` Grant Likely
2010-01-27 12:07 ` [PATCH 2/8 v2] rtc: Add MPC5121 Real time clock driver Anatolij Gustschin
2010-01-27 15:58 ` Grant Likely
2010-01-27 12:07 ` [PATCH 3/8 v2] mtd: Add MPC5121 NAND Flash Controller driver Anatolij Gustschin
2010-01-27 16:43 ` Grant Likely
2010-01-27 20:24 ` Wolfgang Denk
2010-01-27 12:07 ` [PATCH 4/8 v2] dma: Add MPC512x DMA driver Anatolij Gustschin
2010-01-27 12:07 ` [PATCH 5/8 v2] powerpc/mpc5121: add USB host support Anatolij Gustschin
2010-01-27 12:36 ` Jan Andersson
2010-01-27 15:45 ` Anatolij Gustschin
2010-01-27 16:54 ` Grant Likely
2010-01-27 12:07 ` [PATCH 6/8 v2] powerpc/mpc5121: shared DIU framebuffer support Anatolij Gustschin
2010-01-27 12:07 ` Anatolij Gustschin [this message]
2010-01-27 12:07 ` [PATCH 8/8 v2] powerpc/mpc5121: Add default config for MPC5121 Anatolij Gustschin
2010-01-27 14:23 ` [PATCH 0/8] Update support for MPC512x Anatolij Gustschin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1264594052-20317-8-git-send-email-agust@denx.de \
--to=agust@denx.de \
--cc=dzu@denx.de \
--cc=kosmo@semihalf.com \
--cc=linuxppc-dev@ozlabs.org \
--cc=wd@denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).