LinuxPPC-Dev Archive on lore.kernel.org
 help / color / Atom feed
From: Rob Herring <robh@kernel.org>
To: devicetree@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org, Paul Mackerras <paulus@samba.org>,
	linux-kernel@vger.kernel.org
Subject: [PATCH 1/2] dt-bindings: powerpc: Add a schema for the 'sleep' property
Date: Thu,  8 Oct 2020 09:24:19 -0500
Message-ID: <20201008142420.2083861-1-robh@kernel.org> (raw)

Document the PowerPC specific 'sleep' property as a schema. It is
currently only documented in booting-without-of.rst which is getting
removed.

Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/powerpc/sleep.yaml    | 47 +++++++++++++++++++
 1 file changed, 47 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/powerpc/sleep.yaml

diff --git a/Documentation/devicetree/bindings/powerpc/sleep.yaml b/Documentation/devicetree/bindings/powerpc/sleep.yaml
new file mode 100644
index 000000000000..6494c7d08b93
--- /dev/null
+++ b/Documentation/devicetree/bindings/powerpc/sleep.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/powerpc/sleep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PowerPC sleep property
+
+maintainers:
+  - Rob Herring <robh@kernel.org>
+
+description: |
+  Devices on SOCs often have mechanisms for placing devices into low-power
+  states that are decoupled from the devices' own register blocks.  Sometimes,
+  this information is more complicated than a cell-index property can
+  reasonably describe.  Thus, each device controlled in such a manner
+  may contain a "sleep" property which describes these connections.
+
+  The sleep property consists of one or more sleep resources, each of
+  which consists of a phandle to a sleep controller, followed by a
+  controller-specific sleep specifier of zero or more cells.
+
+  The semantics of what type of low power modes are possible are defined
+  by the sleep controller.  Some examples of the types of low power modes
+  that may be supported are:
+
+   - Dynamic: The device may be disabled or enabled at any time.
+   - System Suspend: The device may request to be disabled or remain
+     awake during system suspend, but will not be disabled until then.
+   - Permanent: The device is disabled permanently (until the next hard
+     reset).
+
+  Some devices may share a clock domain with each other, such that they should
+  only be suspended when none of the devices are in use.  Where reasonable,
+  such nodes should be placed on a virtual bus, where the bus has the sleep
+  property.  If the clock domain is shared among devices that cannot be
+  reasonably grouped in this manner, then create a virtual sleep controller
+  (similar to an interrupt nexus, except that defining a standardized
+  sleep-map should wait until its necessity is demonstrated).
+
+select: true
+
+properties:
+  sleep:
+    $ref: /schemas/types.yaml#definitions/phandle-array
+
+additionalProperties: true
-- 
2.25.1


             reply index

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-10-08 14:24 Rob Herring [this message]
2020-10-08 14:24 ` [PATCH 2/2] dt: Remove booting-without-of.rst Rob Herring
2020-10-08 15:03   ` Borislav Petkov
2020-10-09  3:51   ` Michael Ellerman
2020-10-21  6:45   ` Mauro Carvalho Chehab
2021-01-17 16:10 ` [PATCH 1/2] dt-bindings: powerpc: Add a schema for the 'sleep' property Johan Jonker
2021-01-20  1:44   ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201008142420.2083861-1-robh@kernel.org \
    --to=robh@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linuxppc-dev@lists.ozlabs.org \
    --cc=paulus@samba.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

LinuxPPC-Dev Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linuxppc-dev/0 linuxppc-dev/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linuxppc-dev linuxppc-dev/ https://lore.kernel.org/linuxppc-dev \
		linuxppc-dev@lists.ozlabs.org linuxppc-dev@ozlabs.org
	public-inbox-index linuxppc-dev

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.ozlabs.lists.linuxppc-dev


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git