[PATCH v1 00/12] minor KVM fixes and cleanups

[PATCH v1 00/12] minor KVM fixes and cleanups

[Nicholas Piggin]

Here is the first batch of patches are extracted from the patches of the
KVM C conversion series, plus one new fix (host CTRL not restored) since
v6 was posted.

Please consider for merging.

Thanks,
Nick

Nicholas Piggin (12):
  KVM: PPC: Book3S HV P9: Restore host CTRL SPR after guest exit
  KVM: PPC: Book3S HV: Nested move LPCR sanitising to sanitise_hv_regs
  KVM: PPC: Book3S HV: Add a function to filter guest LPCR bits
  KVM: PPC: Book3S HV: Disallow LPCR[AIL] to be set to 1 or 2
  KVM: PPC: Book3S HV: Prevent radix guests setting LPCR[TC]
  KVM: PPC: Book3S HV: Remove redundant mtspr PSPB
  KVM: PPC: Book3S HV: remove unused kvmppc_h_protect argument
  KVM: PPC: Book3S HV: Fix CONFIG_SPAPR_TCE_IOMMU=n default hcalls
  powerpc/64s: Remove KVM handler support from CBE_RAS interrupts
  powerpc/64s: remove KVM SKIP test from instruction breakpoint handler
  KVM: PPC: Book3S HV: Ensure MSR[ME] is always set in guest MSR
  KVM: PPC: Book3S HV: Ensure MSR[HV] is always clear in guest MSR

 arch/powerpc/include/asm/kvm_book3s.h |  2 +
 arch/powerpc/include/asm/kvm_ppc.h    |  3 +-
 arch/powerpc/kernel/exceptions-64s.S  | 15 +++--
 arch/powerpc/kvm/book3s_hv.c          | 85 ++++++++++++++++++++-------
 arch/powerpc/kvm/book3s_hv_builtin.c  |  3 +
 arch/powerpc/kvm/book3s_hv_nested.c   | 37 +++++++++---
 arch/powerpc/kvm/book3s_hv_rm_mmu.c   |  3 +-
 7 files changed, 109 insertions(+), 39 deletions(-)

-- 
2.23.0

[PATCH v1 01/12] KVM: PPC: Book3S HV P9: Restore host CTRL SPR after guest exit

[Nicholas Piggin]

The host CTRL (runlatch) value is not restored after guest exit. The
host CTRL should always be 1 except in CPU idle code, so this can result
in the host running with runlatch clear, and potentially switching to
a different vCPU which then runs with runlatch clear as well.

This has little effect on P9 machines, CTRL is only responsible for some
PMU counter logic in the host and so other than corner cases of software
relying on that, or explicitly reading the runlatch value (Linux does
not appear to be affected but it's possible non-Linux guests could be),
there should be no execution correctness problem, though it could be
used as a covert channel between guests.

There may be microcontrollers, firmware or monitoring tools that sample
the runlatch value out-of-band, however since the register is writable
by guests, these values would (should) not be relied upon for correct
operation of the host, so suboptimal performance or incorrect reporting
should be the worst problem.

Fixes: 95a6432ce9038 ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kvm/book3s_hv.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/powerpc/kvm/book3s_hv.c b/arch/powerpc/kvm/book3s_hv.c
index 13bad6bf4c95..208a053c9adf 100644
--- a/arch/powerpc/kvm/book3s_hv.c
+++ b/arch/powerpc/kvm/book3s_hv.c
@@ -3728,7 +3728,10 @@ static int kvmhv_p9_guest_entry(struct kvm_vcpu *vcpu, u64 time_limit,
 	vcpu->arch.dec_expires = dec + tb;
 	vcpu->cpu = -1;
 	vcpu->arch.thread_cpu = -1;
+	/* Save guest CTRL register, set runlatch to 1 */
 	vcpu->arch.ctrl = mfspr(SPRN_CTRLF);
+	if (!(vcpu->arch.ctrl & 1))
+		mtspr(SPRN_CTRLT, vcpu->arch.ctrl | 1);
 
 	vcpu->arch.iamr = mfspr(SPRN_IAMR);
 	vcpu->arch.pspb = mfspr(SPRN_PSPB);
-- 
2.23.0

Re: [PATCH v1 01/12] KVM: PPC: Book3S HV P9: Restore host CTRL SPR after guest exit

[Fabiano Rosas]

Nicholas Piggin <npiggin@gmail.com> writes:

> The host CTRL (runlatch) value is not restored after guest exit. The
> host CTRL should always be 1 except in CPU idle code, so this can result
> in the host running with runlatch clear, and potentially switching to
> a different vCPU which then runs with runlatch clear as well.
>
> This has little effect on P9 machines, CTRL is only responsible for some
> PMU counter logic in the host and so other than corner cases of software
> relying on that, or explicitly reading the runlatch value (Linux does
> not appear to be affected but it's possible non-Linux guests could be),
> there should be no execution correctness problem, though it could be
> used as a covert channel between guests.
>
> There may be microcontrollers, firmware or monitoring tools that sample
> the runlatch value out-of-band, however since the register is writable
> by guests, these values would (should) not be relied upon for correct
> operation of the host, so suboptimal performance or incorrect reporting
> should be the worst problem.
>
> Fixes: 95a6432ce9038 ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests")
> Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
> ---
>  arch/powerpc/kvm/book3s_hv.c | 3 +++
>  1 file changed, 3 insertions(+)
>
> diff --git a/arch/powerpc/kvm/book3s_hv.c b/arch/powerpc/kvm/book3s_hv.c
> index 13bad6bf4c95..208a053c9adf 100644
> --- a/arch/powerpc/kvm/book3s_hv.c
> +++ b/arch/powerpc/kvm/book3s_hv.c
> @@ -3728,7 +3728,10 @@ static int kvmhv_p9_guest_entry(struct kvm_vcpu *vcpu, u64 time_limit,
>  	vcpu->arch.dec_expires = dec + tb;
>  	vcpu->cpu = -1;
>  	vcpu->arch.thread_cpu = -1;
> +	/* Save guest CTRL register, set runlatch to 1 */
>  	vcpu->arch.ctrl = mfspr(SPRN_CTRLF);
> +	if (!(vcpu->arch.ctrl & 1))
> +		mtspr(SPRN_CTRLT, vcpu->arch.ctrl | 1);

Maybe ditch the comment and use the already defined CTRL_RUNLATCH?

>
>  	vcpu->arch.iamr = mfspr(SPRN_IAMR);
>  	vcpu->arch.pspb = mfspr(SPRN_PSPB);

Re: [PATCH v1 01/12] KVM: PPC: Book3S HV P9: Restore host CTRL SPR after guest exit

[Nicholas Piggin]

Excerpts from Fabiano Rosas's message of April 13, 2021 12:06 am:
> Nicholas Piggin <npiggin@gmail.com> writes:
> 
>> The host CTRL (runlatch) value is not restored after guest exit. The
>> host CTRL should always be 1 except in CPU idle code, so this can result
>> in the host running with runlatch clear, and potentially switching to
>> a different vCPU which then runs with runlatch clear as well.
>>
>> This has little effect on P9 machines, CTRL is only responsible for some
>> PMU counter logic in the host and so other than corner cases of software
>> relying on that, or explicitly reading the runlatch value (Linux does
>> not appear to be affected but it's possible non-Linux guests could be),
>> there should be no execution correctness problem, though it could be
>> used as a covert channel between guests.
>>
>> There may be microcontrollers, firmware or monitoring tools that sample
>> the runlatch value out-of-band, however since the register is writable
>> by guests, these values would (should) not be relied upon for correct
>> operation of the host, so suboptimal performance or incorrect reporting
>> should be the worst problem.
>>
>> Fixes: 95a6432ce9038 ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests")
>> Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
>> ---
>>  arch/powerpc/kvm/book3s_hv.c | 3 +++
>>  1 file changed, 3 insertions(+)
>>
>> diff --git a/arch/powerpc/kvm/book3s_hv.c b/arch/powerpc/kvm/book3s_hv.c
>> index 13bad6bf4c95..208a053c9adf 100644
>> --- a/arch/powerpc/kvm/book3s_hv.c
>> +++ b/arch/powerpc/kvm/book3s_hv.c
>> @@ -3728,7 +3728,10 @@ static int kvmhv_p9_guest_entry(struct kvm_vcpu *vcpu, u64 time_limit,
>>  	vcpu->arch.dec_expires = dec + tb;
>>  	vcpu->cpu = -1;
>>  	vcpu->arch.thread_cpu = -1;
>> +	/* Save guest CTRL register, set runlatch to 1 */
>>  	vcpu->arch.ctrl = mfspr(SPRN_CTRLF);
>> +	if (!(vcpu->arch.ctrl & 1))
>> +		mtspr(SPRN_CTRLT, vcpu->arch.ctrl | 1);
> 
> Maybe ditch the comment and use the already defined CTRL_RUNLATCH?

I did it this way so you can more easily match up the C with the 
existing asm version.

I have a later patch to clean up CTRL handling a bit (in both C and 
asm).

Thanks,
Nick

[PATCH v1 02/12] KVM: PPC: Book3S HV: Nested move LPCR sanitising to sanitise_hv_regs

[Nicholas Piggin]

This will get a bit more complicated in future patches. Move it
into the helper function.

This change allows the L1 hypervisor to determine some of the LPCR
bits that the L0 is using to run it, which could be a privilege
violation (LPCR is HV-privileged), although the same problem exists
now for HFSCR for example. Discussion of the HV privilege issue is
ongoing and can be resolved with a later change.

Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kvm/book3s_hv_nested.c | 27 +++++++++++++++++++++------
 1 file changed, 21 insertions(+), 6 deletions(-)

diff --git a/arch/powerpc/kvm/book3s_hv_nested.c b/arch/powerpc/kvm/book3s_hv_nested.c
index 0cd0e7aad588..3060e5deffc8 100644
--- a/arch/powerpc/kvm/book3s_hv_nested.c
+++ b/arch/powerpc/kvm/book3s_hv_nested.c
@@ -132,8 +132,27 @@ static void save_hv_return_state(struct kvm_vcpu *vcpu, int trap,
 	}
 }
 
+/*
+ * This can result in some L0 HV register state being leaked to an L1
+ * hypervisor when the hv_guest_state is copied back to the guest after
+ * being modified here.
+ *
+ * There is no known problem with such a leak, and in many cases these
+ * register settings could be derived by the guest by observing behaviour
+ * and timing, interrupts, etc., but it is an issue to consider.
+ */
 static void sanitise_hv_regs(struct kvm_vcpu *vcpu, struct hv_guest_state *hr)
 {
+	struct kvmppc_vcore *vc = vcpu->arch.vcore;
+	u64 mask;
+
+	/*
+	 * Don't let L1 change LPCR bits for the L2 except these:
+	 */
+	mask = LPCR_DPFD | LPCR_ILE | LPCR_TC | LPCR_AIL | LPCR_LD |
+		LPCR_LPES | LPCR_MER;
+	hr->lpcr = (vc->lpcr & ~mask) | (hr->lpcr & mask);
+
 	/*
 	 * Don't let L1 enable features for L2 which we've disabled for L1,
 	 * but preserve the interrupt cause field.
@@ -271,8 +290,6 @@ long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
 	u64 hv_ptr, regs_ptr;
 	u64 hdec_exp;
 	s64 delta_purr, delta_spurr, delta_ic, delta_vtb;
-	u64 mask;
-	unsigned long lpcr;
 
 	if (vcpu->kvm->arch.l1_ptcr == 0)
 		return H_NOT_AVAILABLE;
@@ -321,9 +338,7 @@ long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
 	vcpu->arch.nested_vcpu_id = l2_hv.vcpu_token;
 	vcpu->arch.regs = l2_regs;
 	vcpu->arch.shregs.msr = vcpu->arch.regs.msr;
-	mask = LPCR_DPFD | LPCR_ILE | LPCR_TC | LPCR_AIL | LPCR_LD |
-		LPCR_LPES | LPCR_MER;
-	lpcr = (vc->lpcr & ~mask) | (l2_hv.lpcr & mask);
+
 	sanitise_hv_regs(vcpu, &l2_hv);
 	restore_hv_regs(vcpu, &l2_hv);
 
@@ -335,7 +350,7 @@ long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
 			r = RESUME_HOST;
 			break;
 		}
-		r = kvmhv_run_single_vcpu(vcpu, hdec_exp, lpcr);
+		r = kvmhv_run_single_vcpu(vcpu, hdec_exp, l2_hv.lpcr);
 	} while (is_kvmppc_resume_guest(r));
 
 	/* save L2 state for return */
-- 
2.23.0

[PATCH v1 03/12] KVM: PPC: Book3S HV: Add a function to filter guest LPCR bits

[Nicholas Piggin]

Guest LPCR depends on hardware type, and future changes will add
restrictions based on errata and guest MMU mode. Move this logic
to a common function and use it for the cases where the guest
wants to update its LPCR (or the LPCR of a nested guest).

This also adds a warning in other places that set or update LPCR
if we try to set something that would have been disallowed by
the filter, as a sanity check.

Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/include/asm/kvm_book3s.h |  2 +
 arch/powerpc/kvm/book3s_hv.c          | 68 ++++++++++++++++++++-------
 arch/powerpc/kvm/book3s_hv_nested.c   |  8 +++-
 3 files changed, 59 insertions(+), 19 deletions(-)

diff --git a/arch/powerpc/include/asm/kvm_book3s.h b/arch/powerpc/include/asm/kvm_book3s.h
index 2f5f919f6cd3..c58121508157 100644
--- a/arch/powerpc/include/asm/kvm_book3s.h
+++ b/arch/powerpc/include/asm/kvm_book3s.h
@@ -258,6 +258,8 @@ extern long kvmppc_hv_get_dirty_log_hpt(struct kvm *kvm,
 extern void kvmppc_harvest_vpa_dirty(struct kvmppc_vpa *vpa,
 			struct kvm_memory_slot *memslot,
 			unsigned long *map);
+extern unsigned long kvmppc_filter_lpcr_hv(struct kvm *kvm,
+			unsigned long lpcr);
 extern void kvmppc_update_lpcr(struct kvm *kvm, unsigned long lpcr,
 			unsigned long mask);
 extern void kvmppc_set_fscr(struct kvm_vcpu *vcpu, u64 fscr);
diff --git a/arch/powerpc/kvm/book3s_hv.c b/arch/powerpc/kvm/book3s_hv.c
index 208a053c9adf..268e31c7e49c 100644
--- a/arch/powerpc/kvm/book3s_hv.c
+++ b/arch/powerpc/kvm/book3s_hv.c
@@ -1635,6 +1635,35 @@ static int kvm_arch_vcpu_ioctl_set_sregs_hv(struct kvm_vcpu *vcpu,
 	return 0;
 }
 
+/*
+ * Enforce limits on guest LPCR values based on hardware availability,
+ * guest configuration, and possibly hypervisor support and security
+ * concerns.
+ */
+unsigned long kvmppc_filter_lpcr_hv(struct kvm *kvm, unsigned long lpcr)
+{
+	/* On POWER8 and above, userspace can modify AIL */
+	if (!cpu_has_feature(CPU_FTR_ARCH_207S))
+		lpcr &= ~LPCR_AIL;
+
+	/*
+	 * On POWER9, allow userspace to enable large decrementer for the
+	 * guest, whether or not the host has it enabled.
+	 */
+	if (!cpu_has_feature(CPU_FTR_ARCH_300))
+		lpcr &= ~LPCR_LD;
+
+	return lpcr;
+}
+
+static void verify_lpcr(struct kvm *kvm, unsigned long lpcr)
+{
+	if (lpcr != kvmppc_filter_lpcr_hv(kvm, lpcr)) {
+		WARN_ONCE(1, "lpcr 0x%lx differs from filtered 0x%lx\n",
+			  lpcr, kvmppc_filter_lpcr_hv(kvm, lpcr));
+	}
+}
+
 static void kvmppc_set_lpcr(struct kvm_vcpu *vcpu, u64 new_lpcr,
 		bool preserve_top32)
 {
@@ -1643,6 +1672,23 @@ static void kvmppc_set_lpcr(struct kvm_vcpu *vcpu, u64 new_lpcr,
 	u64 mask;
 
 	spin_lock(&vc->lock);
+
+	/*
+	 * Userspace can only modify
+	 * DPFD (default prefetch depth), ILE (interrupt little-endian),
+	 * TC (translation control), AIL (alternate interrupt location),
+	 * LD (large decrementer).
+	 * These are subject to restrictions from kvmppc_filter_lcpr_hv().
+	 */
+	mask = LPCR_DPFD | LPCR_ILE | LPCR_TC | LPCR_AIL | LPCR_LD;
+
+	/* Broken 32-bit version of LPCR must not clear top bits */
+	if (preserve_top32)
+		mask &= 0xFFFFFFFF;
+
+	new_lpcr = kvmppc_filter_lpcr_hv(kvm,
+			(vc->lpcr & ~mask) | (new_lpcr & mask));
+
 	/*
 	 * If ILE (interrupt little-endian) has changed, update the
 	 * MSR_LE bit in the intr_msr for each vcpu in this vcore.
@@ -1661,25 +1707,8 @@ static void kvmppc_set_lpcr(struct kvm_vcpu *vcpu, u64 new_lpcr,
 		}
 	}
 
-	/*
-	 * Userspace can only modify DPFD (default prefetch depth),
-	 * ILE (interrupt little-endian) and TC (translation control).
-	 * On POWER8 and POWER9 userspace can also modify AIL (alt. interrupt loc.).
-	 */
-	mask = LPCR_DPFD | LPCR_ILE | LPCR_TC;
-	if (cpu_has_feature(CPU_FTR_ARCH_207S))
-		mask |= LPCR_AIL;
-	/*
-	 * On POWER9, allow userspace to enable large decrementer for the
-	 * guest, whether or not the host has it enabled.
-	 */
-	if (cpu_has_feature(CPU_FTR_ARCH_300))
-		mask |= LPCR_LD;
+	vc->lpcr = new_lpcr;
 
-	/* Broken 32-bit version of LPCR must not clear top bits */
-	if (preserve_top32)
-		mask &= 0xFFFFFFFF;
-	vc->lpcr = (vc->lpcr & ~mask) | (new_lpcr & mask);
 	spin_unlock(&vc->lock);
 }
 
@@ -4644,8 +4673,10 @@ void kvmppc_update_lpcr(struct kvm *kvm, unsigned long lpcr, unsigned long mask)
 		struct kvmppc_vcore *vc = kvm->arch.vcores[i];
 		if (!vc)
 			continue;
+
 		spin_lock(&vc->lock);
 		vc->lpcr = (vc->lpcr & ~mask) | lpcr;
+		verify_lpcr(kvm, vc->lpcr);
 		spin_unlock(&vc->lock);
 		if (++cores_done >= kvm->arch.online_vcores)
 			break;
@@ -4973,6 +5004,7 @@ static int kvmppc_core_init_vm_hv(struct kvm *kvm)
 		kvmppc_setup_partition_table(kvm);
 	}
 
+	verify_lpcr(kvm, lpcr);
 	kvm->arch.lpcr = lpcr;
 
 	/* Initialization for future HPT resizes */
diff --git a/arch/powerpc/kvm/book3s_hv_nested.c b/arch/powerpc/kvm/book3s_hv_nested.c
index 3060e5deffc8..d14fe32f167b 100644
--- a/arch/powerpc/kvm/book3s_hv_nested.c
+++ b/arch/powerpc/kvm/book3s_hv_nested.c
@@ -151,7 +151,13 @@ static void sanitise_hv_regs(struct kvm_vcpu *vcpu, struct hv_guest_state *hr)
 	 */
 	mask = LPCR_DPFD | LPCR_ILE | LPCR_TC | LPCR_AIL | LPCR_LD |
 		LPCR_LPES | LPCR_MER;
-	hr->lpcr = (vc->lpcr & ~mask) | (hr->lpcr & mask);
+
+	/*
+	 * Additional filtering is required depending on hardware
+	 * and configuration.
+	 */
+	hr->lpcr = kvmppc_filter_lpcr_hv(vcpu->kvm,
+			(vc->lpcr & ~mask) | (hr->lpcr & mask));
 
 	/*
 	 * Don't let L1 enable features for L2 which we've disabled for L1,
-- 
2.23.0

[PATCH v1 04/12] KVM: PPC: Book3S HV: Disallow LPCR[AIL] to be set to 1 or 2

[Nicholas Piggin]

These are already disallowed by H_SET_MODE from the guest, also disallow
these by updating LPCR directly.

AIL modes can affect the host interrupt behaviour while the guest LPCR
value is set, so filter it here too.

Acked-by: Paul Mackerras <paulus@ozlabs.org>
Suggested-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kvm/book3s_hv.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/arch/powerpc/kvm/book3s_hv.c b/arch/powerpc/kvm/book3s_hv.c
index 268e31c7e49c..3de8a1f89a7d 100644
--- a/arch/powerpc/kvm/book3s_hv.c
+++ b/arch/powerpc/kvm/book3s_hv.c
@@ -803,7 +803,10 @@ static int kvmppc_h_set_mode(struct kvm_vcpu *vcpu, unsigned long mflags,
 		vcpu->arch.dawrx1 = value2;
 		return H_SUCCESS;
 	case H_SET_MODE_RESOURCE_ADDR_TRANS_MODE:
-		/* KVM does not support mflags=2 (AIL=2) */
+		/*
+		 * KVM does not support mflags=2 (AIL=2) and AIL=1 is reserved.
+		 * Keep this in synch with kvmppc_filter_guest_lpcr_hv.
+		 */
 		if (mflags != 0 && mflags != 3)
 			return H_UNSUPPORTED_FLAG_START;
 		return H_TOO_HARD;
@@ -1645,6 +1648,8 @@ unsigned long kvmppc_filter_lpcr_hv(struct kvm *kvm, unsigned long lpcr)
 	/* On POWER8 and above, userspace can modify AIL */
 	if (!cpu_has_feature(CPU_FTR_ARCH_207S))
 		lpcr &= ~LPCR_AIL;
+	if ((lpcr & LPCR_AIL) != LPCR_AIL_3)
+		lpcr &= ~LPCR_AIL; /* LPCR[AIL]=1/2 is disallowed */
 
 	/*
 	 * On POWER9, allow userspace to enable large decrementer for the
-- 
2.23.0

[PATCH v1 05/12] KVM: PPC: Book3S HV: Prevent radix guests setting LPCR[TC]

[Nicholas Piggin]

Prevent radix guests setting LPCR[TC]. This bit only applies to hash
partitions.

Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kvm/book3s_hv.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/powerpc/kvm/book3s_hv.c b/arch/powerpc/kvm/book3s_hv.c
index 3de8a1f89a7d..70c6e9c27eb7 100644
--- a/arch/powerpc/kvm/book3s_hv.c
+++ b/arch/powerpc/kvm/book3s_hv.c
@@ -1645,6 +1645,10 @@ static int kvm_arch_vcpu_ioctl_set_sregs_hv(struct kvm_vcpu *vcpu,
  */
 unsigned long kvmppc_filter_lpcr_hv(struct kvm *kvm, unsigned long lpcr)
 {
+	/* LPCR_TC only applies to HPT guests */
+	if (kvm_is_radix(kvm))
+		lpcr &= ~LPCR_TC;
+
 	/* On POWER8 and above, userspace can modify AIL */
 	if (!cpu_has_feature(CPU_FTR_ARCH_207S))
 		lpcr &= ~LPCR_AIL;
-- 
2.23.0

[PATCH v1 06/12] KVM: PPC: Book3S HV: Remove redundant mtspr PSPB

[Nicholas Piggin]

This SPR is set to 0 twice when exiting the guest.

Acked-by: Paul Mackerras <paulus@ozlabs.org>
Suggested-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kvm/book3s_hv.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/powerpc/kvm/book3s_hv.c b/arch/powerpc/kvm/book3s_hv.c
index 70c6e9c27eb7..b88df175aa76 100644
--- a/arch/powerpc/kvm/book3s_hv.c
+++ b/arch/powerpc/kvm/book3s_hv.c
@@ -3790,7 +3790,6 @@ static int kvmhv_p9_guest_entry(struct kvm_vcpu *vcpu, u64 time_limit,
 	mtspr(SPRN_DSCR, host_dscr);
 	mtspr(SPRN_TIDR, host_tidr);
 	mtspr(SPRN_IAMR, host_iamr);
-	mtspr(SPRN_PSPB, 0);
 
 	if (host_amr != vcpu->arch.amr)
 		mtspr(SPRN_AMR, host_amr);
-- 
2.23.0

[PATCH v1 07/12] KVM: PPC: Book3S HV: remove unused kvmppc_h_protect argument

[Nicholas Piggin]

The va argument is not used in the function or set by its asm caller,
so remove it to be safe.

Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/include/asm/kvm_ppc.h  | 3 +--
 arch/powerpc/kvm/book3s_hv_rm_mmu.c | 3 +--
 2 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/powerpc/include/asm/kvm_ppc.h b/arch/powerpc/include/asm/kvm_ppc.h
index 8aacd76bb702..9531b1c1b190 100644
--- a/arch/powerpc/include/asm/kvm_ppc.h
+++ b/arch/powerpc/include/asm/kvm_ppc.h
@@ -767,8 +767,7 @@ long kvmppc_h_remove(struct kvm_vcpu *vcpu, unsigned long flags,
                      unsigned long pte_index, unsigned long avpn);
 long kvmppc_h_bulk_remove(struct kvm_vcpu *vcpu);
 long kvmppc_h_protect(struct kvm_vcpu *vcpu, unsigned long flags,
-                      unsigned long pte_index, unsigned long avpn,
-                      unsigned long va);
+                      unsigned long pte_index, unsigned long avpn);
 long kvmppc_h_read(struct kvm_vcpu *vcpu, unsigned long flags,
                    unsigned long pte_index);
 long kvmppc_h_clear_ref(struct kvm_vcpu *vcpu, unsigned long flags,
diff --git a/arch/powerpc/kvm/book3s_hv_rm_mmu.c b/arch/powerpc/kvm/book3s_hv_rm_mmu.c
index 88da2764c1bb..7af7c70f1468 100644
--- a/arch/powerpc/kvm/book3s_hv_rm_mmu.c
+++ b/arch/powerpc/kvm/book3s_hv_rm_mmu.c
@@ -673,8 +673,7 @@ long kvmppc_h_bulk_remove(struct kvm_vcpu *vcpu)
 }
 
 long kvmppc_h_protect(struct kvm_vcpu *vcpu, unsigned long flags,
-		      unsigned long pte_index, unsigned long avpn,
-		      unsigned long va)
+		      unsigned long pte_index, unsigned long avpn)
 {
 	struct kvm *kvm = vcpu->kvm;
 	__be64 *hpte;
-- 
2.23.0

[PATCH v1 08/12] KVM: PPC: Book3S HV: Fix CONFIG_SPAPR_TCE_IOMMU=n default hcalls

[Nicholas Piggin]

This config option causes the warning in init_default_hcalls to fire
because the TCE handlers are in the default hcall list but not
implemented.

Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kvm/book3s_hv.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/powerpc/kvm/book3s_hv.c b/arch/powerpc/kvm/book3s_hv.c
index b88df175aa76..4a532410e128 100644
--- a/arch/powerpc/kvm/book3s_hv.c
+++ b/arch/powerpc/kvm/book3s_hv.c
@@ -5412,8 +5412,10 @@ static unsigned int default_hcall_list[] = {
 	H_READ,
 	H_PROTECT,
 	H_BULK_REMOVE,
+#ifdef CONFIG_SPAPR_TCE_IOMMU
 	H_GET_TCE,
 	H_PUT_TCE,
+#endif
 	H_SET_DABR,
 	H_SET_XDABR,
 	H_CEDE,
-- 
2.23.0

[PATCH v1 09/12] powerpc/64s: Remove KVM handler support from CBE_RAS interrupts

[Nicholas Piggin]

Cell does not support KVM.

Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kernel/exceptions-64s.S | 6 ------
 1 file changed, 6 deletions(-)

diff --git a/arch/powerpc/kernel/exceptions-64s.S b/arch/powerpc/kernel/exceptions-64s.S
index 8082b690e874..a0515cb829c2 100644
--- a/arch/powerpc/kernel/exceptions-64s.S
+++ b/arch/powerpc/kernel/exceptions-64s.S
@@ -2530,8 +2530,6 @@ EXC_VIRT_NONE(0x5100, 0x100)
 INT_DEFINE_BEGIN(cbe_system_error)
 	IVEC=0x1200
 	IHSRR=1
-	IKVM_SKIP=1
-	IKVM_REAL=1
 INT_DEFINE_END(cbe_system_error)
 
 EXC_REAL_BEGIN(cbe_system_error, 0x1200, 0x100)
@@ -2701,8 +2699,6 @@ EXC_COMMON_BEGIN(denorm_exception_common)
 INT_DEFINE_BEGIN(cbe_maintenance)
 	IVEC=0x1600
 	IHSRR=1
-	IKVM_SKIP=1
-	IKVM_REAL=1
 INT_DEFINE_END(cbe_maintenance)
 
 EXC_REAL_BEGIN(cbe_maintenance, 0x1600, 0x100)
@@ -2754,8 +2750,6 @@ EXC_COMMON_BEGIN(altivec_assist_common)
 INT_DEFINE_BEGIN(cbe_thermal)
 	IVEC=0x1800
 	IHSRR=1
-	IKVM_SKIP=1
-	IKVM_REAL=1
 INT_DEFINE_END(cbe_thermal)
 
 EXC_REAL_BEGIN(cbe_thermal, 0x1800, 0x100)
-- 
2.23.0

[PATCH v1 10/12] powerpc/64s: remove KVM SKIP test from instruction breakpoint handler

[Nicholas Piggin]

The code being executed in KVM_GUEST_MODE_SKIP is hypervisor code with
MSR[IR]=0, so the faults of concern are the d-side ones caused by access
to guest context by the hypervisor.

Instruction breakpoint interrupts are not a concern here. It's unlikely
any good would come of causing breaks in this code, but skipping the
instruction that caused it won't help matters (e.g., skip the mtmsr that
sets MSR[DR]=0 or clears KVM_GUEST_MODE_SKIP).

 [Paul notes: "the 0x1300 interrupt was dropped from the architecture a
  long time ago and is not generated by P7, P8, P9 or P10." So add a
  comment about this in the handler code while we're here. ]

Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kernel/exceptions-64s.S | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/arch/powerpc/kernel/exceptions-64s.S b/arch/powerpc/kernel/exceptions-64s.S
index a0515cb829c2..358cd4b0c08e 100644
--- a/arch/powerpc/kernel/exceptions-64s.S
+++ b/arch/powerpc/kernel/exceptions-64s.S
@@ -2549,11 +2549,16 @@ EXC_REAL_NONE(0x1200, 0x100)
 EXC_VIRT_NONE(0x5200, 0x100)
 #endif
 
-
+/**
+ * Interrupt 0x1300 - Instruction Address Breakpoint Interrupt.
+ * This has been removed from the ISA before 2.01, which is the earliest
+ * 64-bit BookS ISA supported, however the G5 / 970 implements this
+ * interrupt with a non-architected feature available through the support
+ * processor interface.
+ */
 INT_DEFINE_BEGIN(instruction_breakpoint)
 	IVEC=0x1300
 #ifdef CONFIG_KVM_BOOK3S_PR_POSSIBLE
-	IKVM_SKIP=1
 	IKVM_REAL=1
 #endif
 INT_DEFINE_END(instruction_breakpoint)
-- 
2.23.0

[PATCH v1 11/12] KVM: PPC: Book3S HV: Ensure MSR[ME] is always set in guest MSR

[Nicholas Piggin]

Rather than add the ME bit to the MSR at guest entry, make it clear
that the hypervisor does not allow the guest to clear the bit.

The ME set is kept in guest entry for now, but a future patch will
warn if it's not present.

Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kvm/book3s_hv_builtin.c | 3 +++
 arch/powerpc/kvm/book3s_hv_nested.c  | 4 +++-
 2 files changed, 6 insertions(+), 1 deletion(-)

diff --git a/arch/powerpc/kvm/book3s_hv_builtin.c b/arch/powerpc/kvm/book3s_hv_builtin.c
index 158d309b42a3..41cb03d0bde4 100644
--- a/arch/powerpc/kvm/book3s_hv_builtin.c
+++ b/arch/powerpc/kvm/book3s_hv_builtin.c
@@ -662,6 +662,9 @@ static void kvmppc_end_cede(struct kvm_vcpu *vcpu)
 
 void kvmppc_set_msr_hv(struct kvm_vcpu *vcpu, u64 msr)
 {
+	/* Guest must always run with ME enabled. */
+	msr = msr | MSR_ME;
+
 	/*
 	 * Check for illegal transactional state bit combination
 	 * and if we find it, force the TS field to a safe state.
diff --git a/arch/powerpc/kvm/book3s_hv_nested.c b/arch/powerpc/kvm/book3s_hv_nested.c
index d14fe32f167b..fb03085c902b 100644
--- a/arch/powerpc/kvm/book3s_hv_nested.c
+++ b/arch/powerpc/kvm/book3s_hv_nested.c
@@ -343,7 +343,9 @@ long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
 	vcpu->arch.nested = l2;
 	vcpu->arch.nested_vcpu_id = l2_hv.vcpu_token;
 	vcpu->arch.regs = l2_regs;
-	vcpu->arch.shregs.msr = vcpu->arch.regs.msr;
+
+	/* Guest must always run with ME enabled. */
+	vcpu->arch.shregs.msr = vcpu->arch.regs.msr | MSR_ME;
 
 	sanitise_hv_regs(vcpu, &l2_hv);
 	restore_hv_regs(vcpu, &l2_hv);
-- 
2.23.0

[PATCH v1 12/12] KVM: PPC: Book3S HV: Ensure MSR[HV] is always clear in guest MSR

[Nicholas Piggin]

Rather than clear the HV bit from the MSR at guest entry, make it clear
that the hypervisor does not allow the guest to set the bit.

The HV clear is kept in guest entry for now, but a future patch will
warn if it is set.

Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
---
 arch/powerpc/kvm/book3s_hv_builtin.c | 4 ++--
 arch/powerpc/kvm/book3s_hv_nested.c  | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/powerpc/kvm/book3s_hv_builtin.c b/arch/powerpc/kvm/book3s_hv_builtin.c
index 41cb03d0bde4..7a0e33a9c980 100644
--- a/arch/powerpc/kvm/book3s_hv_builtin.c
+++ b/arch/powerpc/kvm/book3s_hv_builtin.c
@@ -662,8 +662,8 @@ static void kvmppc_end_cede(struct kvm_vcpu *vcpu)
 
 void kvmppc_set_msr_hv(struct kvm_vcpu *vcpu, u64 msr)
 {
-	/* Guest must always run with ME enabled. */
-	msr = msr | MSR_ME;
+	/* Guest must always run with ME enabled, HV disabled. */
+	msr = (msr | MSR_ME) & ~MSR_HV;
 
 	/*
 	 * Check for illegal transactional state bit combination
diff --git a/arch/powerpc/kvm/book3s_hv_nested.c b/arch/powerpc/kvm/book3s_hv_nested.c
index fb03085c902b..60724f674421 100644
--- a/arch/powerpc/kvm/book3s_hv_nested.c
+++ b/arch/powerpc/kvm/book3s_hv_nested.c
@@ -344,8 +344,8 @@ long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
 	vcpu->arch.nested_vcpu_id = l2_hv.vcpu_token;
 	vcpu->arch.regs = l2_regs;
 
-	/* Guest must always run with ME enabled. */
-	vcpu->arch.shregs.msr = vcpu->arch.regs.msr | MSR_ME;
+	/* Guest must always run with ME enabled, HV disabled. */
+	vcpu->arch.shregs.msr = (vcpu->arch.regs.msr | MSR_ME) & ~MSR_HV;
 
 	sanitise_hv_regs(vcpu, &l2_hv);
 	restore_hv_regs(vcpu, &l2_hv);
-- 
2.23.0

Re: [PATCH v1 12/12] KVM: PPC: Book3S HV: Ensure MSR[HV] is always clear in guest MSR

[Fabiano Rosas]

Nicholas Piggin <npiggin@gmail.com> writes:

> Rather than clear the HV bit from the MSR at guest entry, make it clear
> that the hypervisor does not allow the guest to set the bit.
>
> The HV clear is kept in guest entry for now, but a future patch will
> warn if it is set.
>
> Acked-by: Paul Mackerras <paulus@ozlabs.org>
> Signed-off-by: Nicholas Piggin <npiggin@gmail.com>

Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>

> ---
>  arch/powerpc/kvm/book3s_hv_builtin.c | 4 ++--
>  arch/powerpc/kvm/book3s_hv_nested.c  | 4 ++--
>  2 files changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/arch/powerpc/kvm/book3s_hv_builtin.c b/arch/powerpc/kvm/book3s_hv_builtin.c
> index 41cb03d0bde4..7a0e33a9c980 100644
> --- a/arch/powerpc/kvm/book3s_hv_builtin.c
> +++ b/arch/powerpc/kvm/book3s_hv_builtin.c
> @@ -662,8 +662,8 @@ static void kvmppc_end_cede(struct kvm_vcpu *vcpu)
>
>  void kvmppc_set_msr_hv(struct kvm_vcpu *vcpu, u64 msr)
>  {
> -	/* Guest must always run with ME enabled. */
> -	msr = msr | MSR_ME;
> +	/* Guest must always run with ME enabled, HV disabled. */
> +	msr = (msr | MSR_ME) & ~MSR_HV;
>
>  	/*
>  	 * Check for illegal transactional state bit combination
> diff --git a/arch/powerpc/kvm/book3s_hv_nested.c b/arch/powerpc/kvm/book3s_hv_nested.c
> index fb03085c902b..60724f674421 100644
> --- a/arch/powerpc/kvm/book3s_hv_nested.c
> +++ b/arch/powerpc/kvm/book3s_hv_nested.c
> @@ -344,8 +344,8 @@ long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
>  	vcpu->arch.nested_vcpu_id = l2_hv.vcpu_token;
>  	vcpu->arch.regs = l2_regs;
>
> -	/* Guest must always run with ME enabled. */
> -	vcpu->arch.shregs.msr = vcpu->arch.regs.msr | MSR_ME;
> +	/* Guest must always run with ME enabled, HV disabled. */
> +	vcpu->arch.shregs.msr = (vcpu->arch.regs.msr | MSR_ME) & ~MSR_HV;
>
>  	sanitise_hv_regs(vcpu, &l2_hv);
>  	restore_hv_regs(vcpu, &l2_hv);

Re: [PATCH v1 00/12] minor KVM fixes and cleanups

[Michael Ellerman]

On Mon, 12 Apr 2021 11:48:33 +1000, Nicholas Piggin wrote:
> Here is the first batch of patches are extracted from the patches of the
> KVM C conversion series, plus one new fix (host CTRL not restored) since
> v6 was posted.
> 
> Please consider for merging.
> 
> Thanks,
> Nick
> 
> [...]

Applied to powerpc/next.

[01/12] KVM: PPC: Book3S HV P9: Restore host CTRL SPR after guest exit
        https://git.kernel.org/powerpc/c/5088eb4092df12d701af8e0e92860b7186365279
[02/12] KVM: PPC: Book3S HV: Nested move LPCR sanitising to sanitise_hv_regs
        https://git.kernel.org/powerpc/c/a19b70abc69aea8ea5974c57e1c3457d9df6aff2
[03/12] KVM: PPC: Book3S HV: Add a function to filter guest LPCR bits
        https://git.kernel.org/powerpc/c/67145ef4960f55923b9e404c0b184944bfeded4d
[04/12] KVM: PPC: Book3S HV: Disallow LPCR[AIL] to be set to 1 or 2
        https://git.kernel.org/powerpc/c/bcc92a0d6d6eae1e7b34a88f58ae69c081d85f97
[05/12] KVM: PPC: Book3S HV: Prevent radix guests setting LPCR[TC]
        https://git.kernel.org/powerpc/c/72c15287210f7433f5fcb55452b05e4b6ccc6c15
[06/12] KVM: PPC: Book3S HV: Remove redundant mtspr PSPB
        https://git.kernel.org/powerpc/c/4b5f0a0d49e663adf1c7c6f2dd05cb18dd53db8c
[07/12] KVM: PPC: Book3S HV: remove unused kvmppc_h_protect argument
        https://git.kernel.org/powerpc/c/6c12c4376bbbc89fc84480096ba838e07ab7c405
[08/12] KVM: PPC: Book3S HV: Fix CONFIG_SPAPR_TCE_IOMMU=n default hcalls
        https://git.kernel.org/powerpc/c/0fd85cb83fbd7048d8a024ba1338924349e26fd5
[09/12] powerpc/64s: Remove KVM handler support from CBE_RAS interrupts
        https://git.kernel.org/powerpc/c/5eee8371828a92a2620453907d6b2b6dc819ab3a
[10/12] powerpc/64s: remove KVM SKIP test from instruction breakpoint handler
        https://git.kernel.org/powerpc/c/da487a5d1bee6a30798a8db15986d3d028c8ac92
[11/12] KVM: PPC: Book3S HV: Ensure MSR[ME] is always set in guest MSR
        https://git.kernel.org/powerpc/c/946cf44ac6ce61378ea02386d39394a06d502f28
[12/12] KVM: PPC: Book3S HV: Ensure MSR[HV] is always clear in guest MSR
        https://git.kernel.org/powerpc/c/732f21a3053cf279eb6b85d19b7818a8f1dd2071

cheers