From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: from mercury.realtime.net (mercury.realtime.net [205.238.132.86]) by ozlabs.org (Postfix) with ESMTP id 754FBDDED6 for ; Tue, 30 Sep 2008 17:42:26 +1000 (EST) In-Reply-To: <20080929200448.GA23025@www.tglx.de> References: <20080923195404.GA10935@www.tglx.de> <200809240124.m8O1O2QK076012@sullivan.realtime.net> <20080929200448.GA23025@www.tglx.de> Mime-Version: 1.0 (Apple Message framework v624) Content-Type: text/plain; charset=US-ASCII; format=flowed Message-Id: <5162f4985b6fa3ced7fe8670cdae926a@bga.com> From: Milton Miller Subject: Re: [RFC] powerpc/boot: add kernel,end node to the cuboot target Date: Tue, 30 Sep 2008 02:44:42 -0500 To: Sebastian Siewior Cc: linuxppc-dev@ozlabs.org, Sebastian Siewior List-Id: Linux on PowerPC Developers Mail List List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , On Sep 29, 2008, at 3:04 PM, Sebastian Siewior wrote: > * Milton Miller | 2008-09-23 20:24:02 [-0500]: > >> If you have any questions about kdump or what needs to happen, >> please feel free to contact me > > I copied most of the 64bit code to parse the device tree without the > pci > nodes & moved it to 32. The userland *could* work, I'm not sure. My > outout is: > > |load: entry = 0x80053c flags = 0 > |nr_segments = 2 > |segment[0].buf = 0x1002b8f0 > |segment[0].bufsz = 80 > |segment[0].mem = (nil) > |segment[0].memsz = 1000 > |segment[1].buf = 0x4803f008 > |segment[1].bufsz = 3a3138 > |segment[1].mem = 0x800000 > |segment[1].memsz = 3b0000 I would expect a third segment (kernel/zImage, dtb, and purgatory), but its not clear that you are getting that far yet. > Now. The entry address in image->start is valid and is the entrypoint > of > the "custom" cuImage. Custom means that it does not depend any register > values passed from u-boot (the original one needs a pointer to bd_t). > The only requirement is a valid 1:1 memory mapping. ok sounds good. does this have the dtb in it too? > I learned, that I can not disable the MMU on Book-E so I have to create > a new temporary mapping in my relocate_new_kernel routine. _start is > doing the same thing what I am trying to accomplish: create a new > mapping and don't kill the current one and switch over. This is done by > disabling all mappings but the current, creating a new mapping with > EFN/RPN = 0 and swapping the TS bit in MAS1. This is my current patch > which is not really working: I have never actually written or debugged any book-E code, and this deals directly with that. However, a quick read of ePAPR chapter 5 suggests that rather than just "the other TS", you want to actively decide that the control will transfer to TS0, and establishing the mappings there. Again, I'm not faimilar with the book-E code, but the kernel itself will use the upper 1/4 of the effective address space by default, so the low offset will likely be available. > diff --git a/arch/powerpc/kernel/misc_32.S > b/arch/powerpc/kernel/misc_32.S > index 7a6dfbc..49c9c2a 100644 > --- a/arch/powerpc/kernel/misc_32.S > +++ b/arch/powerpc/kernel/misc_32.S > @@ -878,22 +878,142 @@ relocate_new_kernel: > /* r4 = reboot_code_buffer */ > /* r5 = start_address */ > > - li r0, 0 > + mr r27, r4 > + mr r28, r5 > + mr r29, r6 > + > + li r25,0 /* phys kernel start (low) */ > + li r24,0 /* CPU number */ > + li r23,0 /* phys kernel start (high) */ > + > + > +/* 1. Find the index of the entry we're executing in */ > + bl invstr /* Find our address */ > +invstr: mflr r6 /* Make it accessible > */ > + mfmsr r7 > + rlwinm r4,r7,27,31,31 /* extract MSR[IS] */ > + mfspr r7, SPRN_PID0 > + slwi r7,r7,16 > + or r7,r7,r4 > + mtspr SPRN_MAS6,r7 > + tlbsx 0,r6 /* search MSR[IS], SPID=PID0 > */ > +#ifndef CONFIG_E200 > + mfspr r7,SPRN_MAS1 > + andis. r7,r7,MAS1_VALID@h > + bne match_TLB > > The branch above is taken, so I've found my current mapping ok, but should you not be using PID0 explictly to say global only? > > + mfspr r7,SPRN_PID1 > + slwi r7,r7,16 > + or r7,r7,r4 > + mtspr SPRN_MAS6,r7 > + tlbsx 0,r6 /* search MSR[IS], SPID=PID1 > */ > + mfspr r7,SPRN_MAS1 > + andis. r7,r7,MAS1_VALID@h > + bne match_TLB > + mfspr r7, SPRN_PID2 > + slwi r7,r7,16 > + or r7,r7,r4 > + mtspr SPRN_MAS6,r7 > + tlbsx 0,r6 /* Fall through, we had to > match */ > +#endif > +match_TLB: > + > + rlwinm r3,r7,16,20,31 /* Extract MAS0(Entry) */ > + > + mfspr r7,SPRN_MAS1 /* Insure IPROT set */ > + oris r7,r7,MAS1_IPROT@h > + mtspr SPRN_MAS1,r7 > + tlbwe > + > +/* 2. Invalidate all entries except the entry we're executing in */ > + mfspr r9,SPRN_TLB1CFG > + andi. r9,r9,0xfff > + li r6,0 /* Set Entry counter to 0 */ > +1: lis r7,0x1000 /* Set MAS0(TLBSEL) = > 1 */ > + rlwimi r7,r6,16,4,15 /* Setup MAS0 = TLBSEL | > ESEL(r6) */ > + mtspr SPRN_MAS0,r7 > + tlbre > + mfspr r7,SPRN_MAS1 > + rlwinm r7,r7,0,2,31 /* Clear MAS1 Valid and > IPROT */ > + cmpw r3,r6 > + beq skpinv /* Dont update the current > execution TLB */ > + mtspr SPRN_MAS1,r7 > + tlbwe > + isync > +skpinv: addi r6,r6,1 /* Increment */ > + cmpw r6,r9 /* Are we done? */ > + bne 1b /* If not, repeat */ > > - /* > - * Set Machine Status Register to a known status, > - * switch the MMU off and jump to 1: in a single step. > - */ > + /* Invalidate TLB0 */ > + li r6,0x04 > + tlbivax 0,r6 > + TLBSYNC > + /* Invalidate TLB1 */ > + li r6,0x0c > + tlbivax 0,r6 > + TLBSYNC > > - mr r8, r0 > - ori r8, r8, MSR_RI|MSR_ME > - mtspr SPRN_SRR1, r8 > - addi r8, r4, 1f - relocate_new_kernel > - mtspr SPRN_SRR0, r8 > - sync > +/* 3. Setup a temp mapping and jump to it */ > + andi. r5, r3, 0x1 /* Find an entry not used and is non-zero */ > + addi r5, r5, 0x1 > + lis r7,0x1000 /* Set MAS0(TLBSEL) = 1 */ > + rlwimi r7,r3,16,4,15 /* Setup MAS0 = TLBSEL | ESEL(r3) */ > + mtspr SPRN_MAS0,r7 > + tlbre > + > + /* set mask to 0xfffff000 , EFN / RPN should be 0 / 0 */ > + li r8, -1 > + li r6, 12 > + slw r6,r8,r6 /* convert to mask */ > + > + li r7, 0 /* find our address */ > + addi r7, r27, current_IP - relocate_new_kernel > +current_IP: > + > + mfspr r8,SPRN_MAS3 > +#ifdef CONFIG_PHYS_64BIT > + mfspr r23,SPRN_MAS7 > +#endif > + and r8,r6,r8 > + subfic r9,r6,-4096 > + and r9,r9,r7 > + > + or r25,r8,r9 > + ori r8,r25,(MAS3_SX|MAS3_SW|MAS3_SR) > + > + /* Just modify the entry ID and EPN for the temp mapping */ > + lis r7,0x1000 /* Set MAS0(TLBSEL) = 1 */ > + rlwimi r7,r5,16,4,15 /* Setup MAS0 = TLBSEL | ESEL(r5) */ > + mtspr SPRN_MAS0,r7 > + xori r6,r4,1 /* Setup TMP mapping in the other Address > space */ > + slwi r6,r6,12 > + oris r6,r6,(MAS1_VALID|MAS1_IPROT)@h > + ori r6,r6,(MAS1_TSIZE(BOOKE_PAGESZ_1GB))@l > + mtspr SPRN_MAS1,r6 > + mfspr r6,SPRN_MAS2 > + li r7,0 /* temp EPN = 0 */ > + rlwimi r7,r6,0,20,31 > + > + mtspr SPRN_MAS2,r7 > + mtspr SPRN_MAS3,r8 > > Here I get: > > MAS0: 0x10010000 > MAS1: 0xc0001a00 > MAS2: 0x00000000 > MAS3: 0x00000015 > > + tlbwe > > I haven't made it to here. or you do make it, but you turned off all of your debugging access to notice. > > + > + xori r6,r4,1 > + slwi r6,r6,5 /* setup new context with other address > space */ > + > + li r7, 0 /* find our address */ > + addi r7, r27, old_copy_code - relocate_new_kernel > + > + mtspr SPRN_SRR0,r7 > + mtspr SPRN_SRR1,r6 > rfi hmm... so you are trying to keep one entry but establish mappings in the other ... > +old_copy_code: > + > + mr r4, r27 > + mr r5, r28 > + mr r6, r29 > + > + li r0, 0 > > -1: > /* from this point address translation is turned off */ > /* and interrupts are disabled */ > > > In order to dump the MASx values, I did not invalidate the TLBs entries > (s/beq skpinv/b skpinv) and branched to address 0 before the tlbwe to > receive a register dump. This little trick did not work after the tlbwe > instruction. I probably overwrote the wrong / active TLB entry. Since > the TI bit is fliped, this new TLB entry should not be used anyway. > Without invalidating the TLBs, I may have picked the wrong ESEL index > and overwrote either my current mapping or that one that used by the > expection handler/serial port and the bug is somewhere else. or you just killed enough of the mappings that the kernel can not take the fault and output the message that yoyu failed. > > Milton, do have an idea how I could debug this further? My cuImage does > not expect any register values or anything so I thing it hangs here > somewhere and never enter the cuImage code. obviously, a jtag or similar hardware debugger would be best. Second best is probably a simulator (I hear qemu has some support for 440, dont' know if its good ebough for this part or not), and third is some other kind of direct memory access (eg if you have a pci card, a firewire plug-in card can dma to ram once its setup). Without that, think about where the context is now, and what you want to end up with. THe kernel normally runs with effective address 0xc0000000 mapped to real 0x00000000 and linear offsets theretwo. But looking at ePAPR, the boot transfer, and also purgatory and cuboot, expect to run in effective=real. While the rfi can do the branch at the end and switch which mode the cpu is running in, I think it needs to end up in space 0 for the next code. Another thing to think about is the device tree the debug io for the boot wrapper. If you have a virt-addr property or even just a linux,stdout setup so that your console works, you will need to make sure that your shutdown space includes the mappnig of the io region (eg serial port). Pmce you establish a method to poke characters then it gets easier to debug. As a final note, it looks like you are currently replacing the code in relocate_new_kernel with book-e code. Obviously this will need refinement to select or move to heat_xx to merge. Again, I don't have any direct experience, but mauybe this gives you some ideas. milton