Hi,
here are logs with debug enabled - working and not working.
I think the most interesitng part from the notworking is this:

<7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [285]
<7>drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [285]
<7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [287]
<7>drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [287]
<7>drivers/input/serio/i8042.c: 93 -> i8042 (command) [290]
<7>drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [290]
<7>drivers/input/serio/i8042.c: fe <- i8042 (interrupt, aux3, 12, bad
parity, timeout) [295]
<7>drivers/input/serio/i8042.c: 93 -> i8042 (command) [295]
<7>drivers/input/serio/i8042.c: ed -> i8042 (parameter) [295]
<7>drivers/input/serio/i8042.c: fe <- i8042 (interrupt, aux3, 12, bad
parity, timeout) [298]
<7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [298]
<7>drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [298]
<7>drivers/input/serio/i8042.c: fe <- i8042 (flush, aux) [300]
<7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [300]
<7>drivers/input/serio/i8042.c: 02 -> i8042 (parameter) [300]
<7>drivers/input/serio/i8042.c: 93 -> i8042 (command) [303]
<7>drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [303]
<7>drivers/input/serio/i8042.c: fe <- i8042 (interrupt, aux3, 12, bad
parity, timeout) [308]
<7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [308]
<7>drivers/input/serio/i8042.c: 00 -> i8042 (parameter) [308]
<7>drivers/input/serio/i8042.c: fe <- i8042 (interrupt, aux3, 12, bad
parity, timeout) [311]

Full logs are attached.
    Milan Roubal

----- Original Message ----- 
From: "Paul Nasrat" <pauln@truemesh.com>
To: "Milan Roubal" <roubm9am@barbora.ms.mff.cuni.cz>
Cc: "Andrew Morton" <akpm@osdl.org>; <linux-kernel@vger.kernel.org>
Sent: Friday, August 15, 2003 1:39 PM
Subject: Re: 2.6.0test3mm2 - Synaptics touchpad problem


> On Fri, Aug 15, 2003 at 01:00:09PM +0200, Milan Roubal wrote:
> > Hi,
> > I am using the new drivers for XFree86 and if the touchpad is visible
>
> Apologies I misread your bug report.  Maybe this will be of more help.
>
> > in dmesg, than it is working in XFree86 too. When it isn't,
> > it isn't than listed in /proc/bus/input/devices and is not working in
> > XFree86.
>
> That does seem odd, I haven't noticed this with vanilla 2.6.0test3
> (linux only, but a reboot linux->linux would exhibit that).
>
> I note on the non synaptics boot you have this instead of the synaptics.
>
> serio: i8042 AUX3 port at 0x60,0x64 irq 12
>
> It may be worth #define DEBUG in i8042.c, to see the differences between
> the two boot sequences in more detail.
>
> You might want to try against 2.6.0-test3, if it works for you
> then it might be worth going through the synaptics patches in mm2 one by
> one :(
>
>
http://www.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.0-test3/2.6.0-test3-mm2/broken-out/
>
>
http://w1.894.telia.com/~u89404340/patches/touchpad/2.6.0-test2/v1/Readme.txt
>
> I'll see if I can replicate this with my laptop this evening.
>
> Paul
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/